- 29 Dec, 2008 40 commits
-
-
Mauro Carvalho Chehab authored
The previous patches removed XCLK and I2C magic. Now, we finally know what those registers do. Also, only a very few cards need different setups for those. Instead of keeping the setups for those values inside the per-device hack magic switch, move the uncommon values to the board-specific struct, and have a common setup for all other boards. So, almost 100 lines of hacking magic were removed. A co-lateral effect of this patch is that it also fixes a bug at em28xx-core, where xclk were set, without taking any care about not overriding a previous xclk setup. Signed-off-by:Mauro Carvalho Chehab <mchehab@redhat.com>
-
Devin Heitmueller authored
Cleanup the calls to set the GPIOs and GPOs for various devices, replacing the register number with the #define from em28xx-reg.h and converting over to using em28xx_write_reg() Signed-off-by:
Devin Heitmueller <devin.heitmueller@gmail.com> Signed-off-by:
-
Devin Heitmueller authored
Convert over to setting the XCLK register usage with the new em28xx_write_reg() function. Thanks to Ray Lu from Empia for providing the em2860/2880 datasheet. Signed-off-by:
-
Uri Shkolnik authored
This patch provides USB suspend and hibernation support for Siano's SMS chipset based USB device Signed-off-by:
Uri Shkolnik <uris@siano-ms.com> Signed-off-by:
Michael Krufky <mkrufky@linuxtv.org> Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Add function smsdvb_read_ucblocks to report uncorrectable error counts. Signed-off-by:
-
Michael Krufky authored
Enable power LED while the frontend is in use. Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
add USB IDs for Hauppauge WinTV MiniCard DVB-T Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Mauro Carvalho Chehab authored
On some em28xx devices, there's an unused interface. This is printed on the logs as an error. We can just ignore that interface. Signed-off-by: -
Jean-Francois Moine authored
Signed-off-by:
Jean-Francois Moine <moinejf@free.fr> Signed-off-by:
-
Antonio Ospite authored
The OmniVision OV534 is the USB bridge chip used in Sony Playstation EYE, it is found also in other webcams like Hercules Blog Webcam and Hercules Dualpix HD. This driver is the port to gspca of a prototype driver by Mark Ferrell based on vivi. The original code to initialize the camera and start the capture is from Jim Paris on ps2dev.org, here integrated with the analysis of the USB communications taken by the windows driver. Signed-off-by:
Antonio Ospite <ospite@studenti.unina.it> Signed-off-by:
-
Jean-Francois Moine authored
Signed-off-by:
-
Jean-Francois Moine authored
Signed-off-by:
-
Jean-Francois Moine authored
The sn9c105 and sn9c120 bridges must be differently programmed for the ov7660. Signed-off-by:
-
Hans de Goede authored
Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Erik Andrén authored
V4L/DVB (9703): Move the s5k4aa vflip quirk table to the main sensor file in order to avoid compilation errors on older kernels Signed-off-by:
Erik Andrén <erik.andren@gmail.com> Signed-off-by:
-
Erik Andrén authored
Signed-off-by:
-
Erik Andrén authored
Signed-off-by:
-
Erik Andrén authored
The msi gx7xx range of computers seem to be a strange lot with lots of different sys vendor names and differently oriented sensors. This commit adds another quirk for a range of them. Signed-off-by:
-
Erik Andrén authored
Signed-off-by:
-
Erik Andrén authored
Signed-off-by:
-
Erik Andrén authored
The gspca conversion deprecated a number of defines. Remove them. Signed-off-by:
-
Jean-Francois Moine authored
Signed-off-by:
-
Hans de Goede authored
Signed-off-by:
-
Hans de Goede authored
The bridge takes some time to update after a write, so apps doing a quick write/read can get the old value back. Signed-off-by:
-
Hans de Goede authored
Currently the spca501 driver only works the first time used, then the cam needs to be unplugged or the driver reloaded, this is because currently the data which should be send each time the stream is started is send only once. Likewise currently the data to initialize the cam is send from the probe function, and thus will not get send after a suspend/resume. This patch fixes this by sending both at the right time. Signed-off-by:
-
Antonio Ospite authored
Some webcams with image transfer by bulk messages accept one or many permanent bulk read. Signed-off-by:
-
Jean-Francois Moine authored
The new exchanges are adapted from MS-win traces and the webcams work better. Signed-off-by:
-
Jean-Francois Moine authored
The driver sn9c102 has no code for the ov7648 sensor. Signed-off-by:
-
Hans Verkuil authored
It is much more readable to swap the byteorder in the switch rather than in each case statement. Signed-off-by:
Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by:
-
Dirk Heer authored
This Patch does modify the bttv-cards.c and bttc.h so that the driver supports VD-011, VD-012, VD-012-X1 and VD-012-X2 Framegrabber from Phytec Messtechnik GmbH. Signed-off-by:
Dirk Heer <d.heer@phytec.de> Signed-off-by:
-
Mauro Carvalho Chehab authored
If removing and reiserting the driver on some devices, tuner type will be unset at the second time. This patch fixes this issue. Signed-off-by: -
Mauro Carvalho Chehab authored
This patch cleans up the entries of xc2028/3028, since those devices don't need or use a tda9887. Signed-off-by: -
Mauro Carvalho Chehab authored
Pixelview uses a Sigmatel stac codec. It has an external line out pin, connected to AC97_MASTER_VOL. It also provides I2S output, but using a Signed-off-by: -
Mauro Carvalho Chehab authored
Some devices use more than one AC97 outputs. This patch allows such devices to properly work. Signed-off-by: -
Mauro Carvalho Chehab authored
Signed-off-by: -
Mauro Carvalho Chehab authored
Some boards use different AC97 setups for output. This patch adds the capability of specifying the output to be used. Currently, only one output is selected, but the better is to allow user to select it via a mixer, on alsa driver. Signed-off-by: -
Mauro Carvalho Chehab authored
Signed-off-by:
-
