X86_64 allmodconfig screams like so:
warning: (PINCTRL_MT6397) selects PINCTRL_MTK_COMMON
which has unmet direct dependencies
(PINCTRL && (ARCH_MEDIATEK || COMPILE_TEST) && OF)

So add OF to dependencies to shut up this warning.

Cc: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Pinctrl module (ioc) controls the Pad's function select
(each pad can have 8 functions), Pad's Drive Strength, Pad's
Pull Select and Pad's Input Disable status.

The ioc has two modules, ioc_top & ioc_rtc. Both of these two
modules have function select/clear, Pull select and Drive
Strength registers. But only ioc_rtc has input-disable
registers. The Pads on ioc_top have to access ioc_rtc to set
their input-disable status and intpu-disable-value.

So have to use one ioc driver instance to drive these two
ioc modules at the same time, and each ioc module will be
treat as one bank on the "IOC Device".

The GPIO Controller controls the GPIO status if the Pad has
been config as GPIO by Pinctrl already. Includes the GPIO
Input/output, Interrupt type, Interrupt Status, and Set/Get
Values.
The GPIO pull up/down are controlled by Pinctrl.

There are 7 GPIO Groups and splited into 3 MACROs in atlas7.
The GPIO Groups in one MACRO share one GPIO controllers, each
GPIO Group are treated as one GPIO bank.

For example:
In VDIFM macro, there is one GPIO Controller, it has 3 banks
to control 3 gpio groups. Its gpio name space is from 0 to 95.

The Device Tree can be written as following:

gpio-ranges = <&pinctrl 0 0 0>,
<&pinctrl 32 0 0>,
<&pinctrl 64 0 0>;

gpio-ranges-group-names = "gnss_gpio_grp",
"lcd_vip_gpio_grp",
"sdio_i2s_gpio_grp";

bank#0 is from 0~31, the pins are from pinctrl's "gnss_gpio_grp".
bank#2 is from 32~63, the pins are from pinctrl's "lcd_vip_gpio_grp".
bank#3 is from 64~95, the pins are from pinctrl's "sdio_i2s_gpio_grp".
Signed-off-by: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This function is only referenced in this file.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

MT8127 pinctrl/eint are similar to mt8135 and mt8173, add
support for mt8127 using mediatek common pinctrl driver.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add mt6397 support using mediatek common pinctrl driver.

mt6397 is a PMIC, and pinctrl/GPIO is part of 6397 chip.
Pinctrl/GPIO driver should obtain regmap from PMIC,
so adding this support to common code.

Also, mt6397 is no need to support interrupt controller,
so changing common code to skip it.
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Input enable and smt setting have different register,
modify code to fix it.

Several mediatek soc use similar input enable/smt setting
procedure as mt8173, some soc use generic input enable/smt
setting, some soc has no input enable/smt setting. Adding
common code to handle all those cases, so future soc driver
can use it.
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Several mediatek soc use similar pull setting procedure as mt8173,
the pupd enable and resistance setting are in the same register.
Add common code mtk_pctrl_spec_pull_set_samereg out of spec_pull_set
in mt8173 to handle this case, so future soc driver can use it.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

struct mtk_desc_pin.chip, mtk_pinctrl_devdata.invser_offset
and mtk_pinctrl_devdata.chip_type are never used in code.
Remove them.

Some per-pin data are using int for pin number and offsets.
Change to short and rearrange to reduce const data size.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add pinfunc header file, mt8135/mt8173 relate dts will include it.
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Since 6397 is no need to support interrupt controller,
moving interrupt controller relate property to optional list.
Also adding mt8173 and mt8127 to bindings.
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add the required group function map and fill it at probe using
the pin capabilities information already present in the driver.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Fixed a small typo in the Cygnus GPIO driver
Signed-off-by: Jason Uy <jasonuy@broadcom.com>
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add a driver for the pin controller present on the IMG Pistachio SoC.
This driver provides pinmux and pinconfig operations as well as GPIO
and IRQ chips for the GPIO banks.

Changes from v4:
 - Switched to using gpiochip_add_pin_range().
 - Fixed up Kconfig entry.
Changes from v3:
 - Addressed review comments from Ezequiel.
Changes from v2:
 - Removed module stuff which would be compiled out.
Changes from v1:
 - Addressed review comments from Linus.
 - Changed compatible string to "img,pistachio-system-pinctrl".
 - Look for GPIO sub-nodes by name.
 - A couple of bug fixes.
Signed-off-by: Damien Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Both pconf_get_pin and pconf_set_pin needs to lookup pin cap based
on the pin number. Create a common helper function that both
functions can use that also handles the case where no pin number is
found in the pins array.

This also fixes a small bug in pconf_get_pin where pconf_get_i2c0
would use the pins array index rather than the pin number.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

As of commit 9d07d414 ("ARM: shmobile: r8a73a4: ape6evm: Remove
legacy platform"), r8a73a4 is only supported in generic ARM
multi-platform builds.  Hence CONFIG_ARCH_MULTIPLATFORM is always set,
and the check can be removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Also renames "R-Car M2" to "R-Car M2-W" to avoid confusion.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Regarding pin control, r8a7791 and r8a7793 are identical, so it is
sufficient to add an sh_pfc_soc_info structure to enable r8a7793 support.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The last serial port is called "SCIFB", not "SCIFAB".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Intel Sunrisepoint-H is a desktop version of the PCH (Platform Controller
Hub). It has slightly different pin configuration compared to the LP
version. This patch adds support for Sunrisepoint-H to the existing
pinctrl-sunrisepoint.c driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

As of commit 9d07d414 ("ARM: shmobile: r8a73a4: ape6evm: Remove
legacy platform"), r8a73a4 is only supported in generic DT-only ARM
multi-platform builds.  The driver doesn't need to match platform
devices by name anymore, hence remove the corresponding
platform_device_id entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Inspired by scripts/coccinelle/api/err_cast.cocci
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The irq_domain_ops are not modified by the driver and the irqdomain core
code accepts pointer to a const data.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The irq_domain_ops are not modified by the driver and the irqdomain core
code accepts pointer to a const data.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The old format to define pinctrl settings for imx in DT has two
hierarchy levels. The first level are function device nodes. The second
level are pingroups which contain a property fsl,pins. The original
intention was to define all pin functions in a single dtsi file and just
reference the correct ones in the board files.
This idea was rejected some time ago leading to the current design to
have all the pinfunctions defined in the board files. So we don't need
the function device nodes anymore.

This patch changes the pinctrl driver to accept devicetrees which do not
have the first hierarchy level, function device nodes. For example
karo-tx25 already has such a devicetree. Old devicetrees are still
parsed and supported.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Since SCLK, MISO and MOSI are the only mandatory signals at Zynq's SPI
interfaces, SS0, SS1 and SS2 have to be configured separately as they may
be used as simple GPIO lines.

This, of course, has to be considered in the devicetree, so pin controller
configuration for e.g. an SPI0 using SS0 and SS1 only might look like the
following snippet (derived from the example of chapter "17.5.3
MIO/EMIO" Routing of Zynq-7000 TRM UG585). So MIO20 can now be used
as GPIO instead of being occupied by SPI0 SS2 function. Note the separate
pinmux function for the slave select signals:

pinctrl_spi0_default: spi0-default {
	mux_spi {
		function = "spi0";
		groups = "spi0_0_grp";
	};

	mux_ss {
		function = "spi0_ss";
		groups = "spi0_0_ss0_grp", "spi0_0_ss1_grp";
	}

	conf-output {
		pins = "MIO16", "MIO21";
		slew-rate = <0>;
		bias-disable;
		low-power-disable;
		io-standard = <1>;
	};

	conf-input {
		pins = "MIO17";
		slew-rate = <0>;
		bias-high-impedance;
		low-power-disable;
		io-standard = <1>;
	};

	conf-select {
		pins = "MIO18", "MIO19";
		slew-rate = <0>;
		bias-pull-up;
		low-power-disable;
		io-standard = <1>;
	};
};

pinctrl_gpio0_default {
	mux {
		function = "gpio0";
		groups = "gpio0_20_grp"
	};

	conf {
		pins = "MIO20";
		slew-rate = <0>;
		bias-pull-up;
		low-power-disable;
		io-standard = <1>;
	};
};
Signed-off-by: Helmut Buchsbaum <helmut.buchsbaum@gmail.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Assign GPIO chip and irqchip to the GPIO container dynamically,
so we can set a unique name for each GPIO irqchip and see what
chip the hwirq offset actually relates to.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This activates strict mode muxing for the Nomadik pin controllers,
as these do not allow GPIO and functions to use the same pin
simultaneously.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

While the pinmux_ops are ideally just a vtable for pin mux
calls, the "strict" setting belongs so intuitively with the
pin multiplexing that we should move it here anyway. Putting
it in the top pinctrl_desc makes no sense.

Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Disallow simultaneous use of the the GPIO and peripheral mux
functions by setting a flag "strict" in struct pinctrl_desc.

The blackfin pinmux and gpio controller doesn't allow user to
set up a pin for both GPIO and peripheral function. So, add flag
strict in struct pinctrl_desc to check both gpio_owner and
mux_owner before approving the pin request.

v2-changes:
- if strict flag is set, check gpio_owner and mux_onwer in if and
  else clause

v3-changes:
- add kerneldoc for this struct
- augment Documentation/pinctrl.txt
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add i.MX7D pinctrl driver support
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add a device-tree binding document for the pin controller present
on the IMG Pistachio SoC.
Signed-off-by: Damien Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Pinctrl driver for the System Control Unit (SCU) found on NXP
LPC18xx/43xx devices.

Driver uses the generic pinctrl DT bindings for multiplexing
and property settings.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds the callback for set_multiple.

As this controller has a separate set and clear register, we
can't write directly to PIO_ODSR as this would required a cached
variable and would race with at91_gpio_set.

So build masks for the PIO_SODR and PIO_CODR registers and
write them together.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Pull ext4 fixes from Ted Ts'o:
 "Some miscellaneous bug fixes and some final on-disk and ABI changes
  for ext4 encryption which provide better security and performance"

* tag 'for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix growing of tiny filesystems
  ext4: move check under lock scope to close a race.
  ext4: fix data corruption caused by unwritten and delayed extents
  ext4 crypto: remove duplicated encryption mode definitions
  ext4 crypto: do not select from EXT4_FS_ENCRYPTION
  ext4 crypto: add padding to filenames before encrypting
  ext4 crypto: simplify and speed up filename encryption