This pull request covers the major oopsing issues with OMAP, caused by
the lack of the TWL driver.  Even when the TWL driver is not built in,
we shouldn't oops.

* 'omap-fixes-urgent' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: omap: fix broken twl-core dependencies and ifdefs
  ARM: omap: fix oops in drivers/video/omap2/dss/dpi.c
  ARM: omap: fix oops in arch/arm/mach-omap2/vp.c when pmic is not found

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: 7322/1: Print BUG instead of undefined instruction on BUG_ON()
  ARM: 7321/1: cache-v7: Disable preemption when reading CCSIDR
  ARM: 7320/1: Fix proc_info table alignment

Some code - especially the crypto layer - wants to use the x86
FP/MMX/AVX register set in what may be interrupt (typically softirq)
context.

That *can* be ok, but the tests for when it was ok were somewhat
suspect.  We cannot touch the thread-specific status bits either, so
we'd better check that we're not going to try to save FP state or
anything like that.

Now, it may be that the TS bit is always cleared *before* we set the
USEDFPU bit (and only set when we had already cleared the USEDFP
before), so the TS bit test may actually have been sufficient, but it
certainly was not obviously so.

So this explicitly verifies that we will not touch the TS_USEDFPU bit,
and adds a few related sanity-checks.  Because it seems that somehow
AES-NI is corrupting user FP state.  The cause is not clear, and this
patch doesn't fix it, but while debugging it I really wanted the code to
be more obviously correct and robust.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

It was marked asmlinkage for some really old and stale legacy reasons.
Fix that and the equally stale comment.

Noticed when debugging the irq_fpu_usable() bugs.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Says Jens:

 "Time to push off some of the pending items.  I really wanted to wait
  until we had the regression nailed, but alas it's not quite there yet.
  But I'm very confident that it's "just" a missing expire on exit, so
  fix from Tejun should be fairly trivial.  I'm headed out for a week on
  the slopes.

  - Killing the barrier part of mtip32xx.  It doesn't really support
    barriers, and it doesn't need them (writes are fully ordered).

  - A few fixes from Dan Carpenter, preventing overflows of integer
    multiplication.

  - A fixup for loop, fixing a previous commit that didn't quite solve
    the partial read problem from Dave Young.

  - A bio integer overflow fix from Kent Overstreet.

  - Improvement/fix of the door "keep locked" part of the cdrom shared
    code from Paolo Benzini.

  - A few cfq fixes from Shaohua Li.

  - A fix for bsg sysfs warning when removing a file it did not create
    from Stanislaw Gruszka.

  - Two fixes for floppy from Vivek, preventing a crash.

  - A few block core fixes from Tejun.  One killing the over-optimized
    ioc exit path, cleaning that up nicely.  Two others fixing an oops
    on elevator switch, due to calling into the scheduler merge check
    code without holding the queue lock."

* 'for-linus' of git://git.kernel.dk/linux-block:
  block: fix lockdep warning on io_context release put_io_context()
  relay: prevent integer overflow in relay_open()
  loop: zero fill bio instead of return -EIO for partial read
  bio: don't overflow in bio_get_nr_vecs()
  floppy: Fix a crash during rmmod
  floppy: Cleanup disk->queue before caling put_disk() if add_disk() was never called
  cdrom: move shared static to cdrom_device_info
  bsg: fix sysfs link remove warning
  block: don't call elevator callbacks for plug merges
  block: separate out blk_rq_merge_ok() and blk_try_merge() from elevator functions
  mtip32xx: removed the irrelevant argument of mtip_hw_submit_io() and the unused member of struct driver_data
  block: strip out locking optimization in put_io_context()
  cdrom: use copy_to_user() without the underscores
  block: fix ioc locking warning
  block: fix NULL icq_cache reference
  block,cfq: change code order

11a3122f "block: strip out locking optimization in put_io_context()"
removed ioc_lock depth lockdep annoation along with locking
optimization; however, while recursing from put_io_context() is no
longer possible, ioc_release_fn() may still end up putting the last
reference of another ioc through elevator, which wlil grab ioc->lock
triggering spurious (as the ioc is always different one) A-A deadlock
warning.

As this can only happen one time from ioc_release_fn(), using non-zero
subclass from ioc_release_fn() is enough.  Use subclass 1.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Quoth David:

1) GRO MAC header comparisons were ethernet specific, breaking other
   link types.  This required a multi-faceted fix to cure the originally
   noted case (Infiniband), because IPoIB was lying about it's actual
   hard header length.  Thanks to Eric Dumazet, Roland Dreier, and
   others.

2) Fix build failure when INET_UDP_DIAG is built in and ipv6 is modular.
   From Anisse Astier.

3) Off by ones and other bug fixes in netprio_cgroup from Neil Horman.

4) ipv4 TCP reset generation needs to respect any network interface
   binding from the socket, otherwise route lookups might give a
   different result than all the other segments received.  From Shawn
   Lu.

5) Fix unintended regression in ipv4 proxy ARP responses, from Thomas
   Graf.

6) Fix SKB under-allocation bug in sh_eth, from Yoshihiro Shimoda.

7) Revert skge PCI mapping changes that are causing crashes for some
   folks, from Stephen Hemminger.

8) IPV4 route lookups fill in the wildcarded fields of the given flow
   lookup key passed in, which is fine most of the time as this is
   exactly what the caller's want.  However there are a few cases that
   want to retain the original flow key values afterwards, so handle
   those cases properly.  Fix from Julian Anastasov.

9) IGB/IXGBE VF lookup bug fixes from Greg Rose.

10) Properly null terminate filename passed to ethtool flash device
    method, from Ben Hutchings.

11) S3 resume fix in via-velocity from David Lv.

12) Fix double SKB free during xmit failure in CAIF, from Dmitry
    Tarnyagin.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (72 commits)
  net: Don't proxy arp respond if iif == rt->dst.dev if private VLAN is disabled
  ipv4: Fix wrong order of ip_rt_get_source() and update iph->daddr.
  netprio_cgroup: fix wrong memory access when NETPRIO_CGROUP=m
  netprio_cgroup: don't allocate prio table when a device is registered
  netprio_cgroup: fix an off-by-one bug
  bna: fix error handling of bnad_get_flash_partition_by_offset()
  isdn: type bug in isdn_net_header()
  net: Make qdisc_skb_cb upper size bound explicit.
  ixgbe: ethtool: stats user buffer overrun
  ixgbe: dcb: up2tc mapping lost on disable/enable CEE DCB state
  ixgbe: do not update real num queues when netdev is going away
  ixgbe: Fix broken dependency on MAX_SKB_FRAGS being related to page size
  ixgbe: Fix case of Tx Hang in PF with 32 VFs
  ixgbe: fix vf lookup
  igb: fix vf lookup
  e1000: add dropped DMA receive enable back in for WoL
  gro: more generic L2 header check
  IPoIB: Stop lying about hard_header_len and use skb->cb to stash LL addresses
  zd1211rw: firmware needs duration_id set to zero for non-pspoll frames
  net: enable TC35815 for MIPS again
  ...

Commit 653241 (net: RFC3069, private VLAN proxy arp support) changed
the behavior of arp proxy to send arp replies back out on the interface
the request came in even if the private VLAN feature is disabled.

Previously we checked rt->dst.dev != skb->dev for in scenarios, when
proxy arp is enabled on for the netdevice and also when individual proxy
neighbour entries have been added.

This patch adds the check back for the pneigh_lookup() scenario.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fix a bug which introduced by commit ac8a4810 (ipv4: Save
nexthop address of LSRR/SSRR option to IPCB.).In that patch, we saved
the nexthop of SRR in ip_option->nexthop and update iph->daddr until
we get to ip_forward_options(), but we need to update it before
ip_rt_get_source(), otherwise we may get a wrong src.
Signed-off-by: Li Wei <lw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the netprio_cgroup module is not loaded, net_prio_subsys_id
is -1, and so sock_update_prioidx() accesses cgroup_subsys array
with negative index subsys[-1].

Make the code resembles cls_cgroup code, which is bug free.
Origionally-authored-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

So we delay the allocation till the priority is set through cgroup,
and this makes skb_update_priority() faster when it's not set.

This also eliminates an off-by-one bug similar with the one fixed
in the previous patch.
Origionally-authored-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

# mount -t cgroup xxx /mnt
  # mkdir /mnt/tmp
  # cat /mnt/tmp/net_prio.ifpriomap
  lo 0
  eth0 0
  virbr0 0
  # echo 'lo 999' > /mnt/tmp/net_prio.ifpriomap
  # cat /mnt/tmp/net_prio.ifpriomap
  lo 999
  eth0 0
  virbr0 4101267344

We got weired output, because we exceeded the boundary of the array.
We may even crash the kernel..
Origionally-authored-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT (v2)
  drm/i915: no lvds quirk for AOpen MP45
  drm/i915: Force explicit bpp selection for intel_dp_link_required
  drm/radeon: do not continue after error from r600_ib_test
  drivers/gpu/drm/drm_ioc32.c: initialize all fields
  drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT
  drm/i915:: Disable FBC on SandyBridge

fix 1 mysterious divide error
fix 3 NULL dereference bugs in writeback tracing, on SD card removal w/o umount

* tag 'writeback-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/wfg/linux:
  writeback: fix dereferencing NULL bdi->dev on trace_writeback_queue
  lib: proportion: lower PROP_MAX_SHIFT to 32 on 64-bit kernel
  writeback: fix NULL bdi->dev in trace writeback_single_inode
  backing-dev: fix wakeup timer races with bdi_unregister()

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: Fix double start/stop in x86_pmu_start()
  perf evsel: Fix an issue where perf report fails to show the proper percentage
  perf tools: Fix prefix matching for kernel maps
  perf tools: Fix perf stack to non executable on x86_64
  perf: Remove deprecated WARN_ON_ONCE()

Couple of regressions, couple of zero-day bugs, a minor enhancement.
Nothing really major.

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (f75375s) Let f75375_update_device treat pwmX as a measured value
  hwmon: (f75375s) Fix bit shifting in f75375_write16
  hwmon: (f75375s) Fix reading of wrong register when initializing the F75387
  hwmon: (f75375s) Fix automatic pwm mode setting for F75373 & F75375
  hwmon: (w83627ehf) Remove duplicate code

Merge branch 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux into drm-fixes

* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux:
  drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT (v2)
  drm/i915: no lvds quirk for AOpen MP45
  drm/i915: Force explicit bpp selection for intel_dp_link_required
  drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT
  drm/i915:: Disable FBC on SandyBridge

"subbuf_size" and "n_subbufs" come from the user and they need to be
capped to prevent an integer overflow.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Serial/TTY fixes for the 3.3-rc3 tree

Just a few new device ids, omap serial driver regression fixes, and a
build fix for the 8250 driver movement.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

* tag 'tty-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: serial: omap-serial: wakeup latency constraint is in microseconds, not milliseconds
  tty: serial: OMAP: block idle while the UART is transferring data in PIO mode
  tty: serial: OMAP: use a 1-byte RX FIFO threshold in PIO mode
  m32r: relocate drivers back out of 8250 dir
  tty: fix a build failure on sparc
  serial: samsung: Add support for EXYNOS5250
  serial: samsung: Add support for EXYNOS4212 and EXYNOS4412
  drivers/tty/vt/vt_ioctl.c: fix KDFONTOP 32bit compatibility layer

Staging tree patches for 3.3-rc3

Big things here is the deletion of the Android pmem driver, as it's
obsolete and no one uses it, the gma500 driver as it's already in the
drm portion of the kernel tree, and the pohmelfs filesystem as it's
obsolete and a rewritten version is being proposed for the fs/ section
of the kernel.

Other than that, a smattering of different bugfixes and regressions, and
some omap drm api merge fixups that were needed due to api changes in
the main portion of the drm tree, allowing this code to build properly
again.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

* tag 'staging-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (28 commits)
  staging: pohmelfs: remove drivers/staging/pohmelfs
  staging: android/ram_console: Don't build on arches w/o ioremap
  staging: r8712u: Use asynchronous firmware loading
  staging: usbip: fix to prevent potentially using uninitialized spinlock
  staging: r8712u: Fix problem when CONFIG_R8712_AP is set
  staging: tidspbridge: fix incorrect free to drv_datap
  staging: tidspbridge: fix bridge_open memory leaks
  staging: android: lowmemorykiller: Don't wait more than one second for a process to die
  MAINTAINERS: staging: iio: add iio information
  staging: zcache: fix serialization bug in zv stats
  staging: fix go7007-usb license
  Staging: android: binder: Fix crashes when sharing a binder file between processes
  Staging: android: Remove pmem driver
  Staging: asus_oled: fix NULL-ptr crash on unloading
  Staging: asus_oled: fix image processing
  Staging: android: binder: Don't call dump_stack in binder_vma_open
  staging: r8712u: Add new Sitecom UsB ID
  zcache: Set SWIZ_BITS to 8 to reduce tmem bucket lock contention.
  zcache: fix deadlock condition
  staging: drm/omap: fix locking issue
  ...

Driver core fixes for the 3.3-rc3 tree.

A few fixes for kobject warnings that have popped up in the cpu hotplug path,
and a regression fix for the speed of the hotplug memory code.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

* tag 'driver-core-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  driver-core: cpu: fix kobject warning when hotplugging a cpu
  ACPI: remove duplicated lines of merging problems with acpi_processor_add
  docbook: fix fatal errors in device-drivers docbook and add DMA Management section
  drivers/base/memory.c: fix memory_dev_init() long delay
  driver core: cpu: remove kernel warning when removing a cpu

Minor char-misc fixes for 3.3-rc3

Nothing big here, some Kconfig fixes for the MISC_DEVICES config option
that was being used incorrectly, and some other minor bug fixes.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

* tag 'char-misc-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  mmc: cb710 core: Add missing spin_lock_init for irq_lock of struct cb710_chip
  cs5535-mfgpt: don't call __init function from __devinit
  vmw_balloon: fix for a -Wuninitialized warning
  drivers: misc: Remove MISC_DEVICES config option
  c2port: fix build error for duramar2150 due to missing header.

USB fixes for 3.3-rc3

Here are a few minor USB fixes and a bunch of device id updates for the
USB drivers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

* tag 'usb-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: usbserial: add new PID number (0xa951) to the ftdi driver
  usb: ch9.h: usb_endpoint_maxp() uses __le16_to_cpu()
  usb: musb: fix a build error on mips
  uwb & wusb & usb wireless controllers: fix kconfig error & build errors
  usb: Skip PCI USB quirk handling for Netlogic XLP
  powerpc/usb: fix issue of CPU halt when missing USB PHY clock
  usb: otg: mv_otg: Add dependence
  usb: host: Distinguish Kconfig text for Freescale controllers
  USB: add new zte 3g-dongle's pid to option.c
  usb: ch9.h: usb_endpoint_maxp() uses __le16_to_cpu()
  USB: qcserial: don't enable autosuspend
  USB: qcserial: add several new serial devices
  usb: otg: mv_otg: Add dependence
  usb: gadget: zero: fix bug in loopback autoresume handling

The current error handling doesn't work because we flash_part is a u32
so the checks for negative error codes don't work.  I considered making
things signed but I don't know the hardware enough to say if that's a
problem.  Really, we don't use the error codes so just returning zero
for all problems is fine.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We use len to store the return value from eth_header().  eth_header()
can return -ETH_HLEN (-14).  We want to pass this back instead of
truncating it to 65522 and returning that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Treat pwmX as a measured value, not as a (mostly static) limit value, so
that it is updated more frequently from the device register.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>

Just like skb->cb[], so that qdisc_skb_cb can be encapsulated inside
of other data structures.

This is intended to be used by IPoIB so that it can remember
addressing information stored at hard_header_ops->create() time that
it can fetch when the packet gets to the transmit routine.
Signed-off-by: David S. Miller <davem@davemloft.net>

The receive FIFO wakeup latency estimate in the omap-serial driver is
three orders of magnitude too small.  This effectively prevents the
MPU from going to a low-power state when CONFIG_CPU_IDLE=y.  This is a
major power management regression and masks some other FIFO-related
bugs in the driver.

Fix by correcting the most egregious problem in the RX wakeup latency
estimate.  There are several other flaws in the estimator; these will
be fixed by a separate patch series intended for 3.4.

The difference in low-power states with this patch can be observed via
debugfs in pm_debug/count.

This estimate does not have any effect when CONFIG_CPU_IDLE=n.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Prevent OMAP UARTs from going idle while they are still transferring
data in PIO mode.  This works around an oversight in the OMAP UART
hardware present in OMAP34xx and earlier: an idle UART won't send a
wakeup when the TX FIFO threshold is reached.  This causes long delays
during data transmission when the MPU powerdomain enters a low-power
mode.  The MPU interrupt controller is not able to respond to
interrupts when it's in a low-power state, so the TX buffer is not
refilled until another wakeup event occurs.

This fix changes the erratum i291 DMA idle workaround.  Rather than
toggling between force-idle and no-idle, it will toggle between
smart-idle and no-idle.  The important part of the workaround is the
no-idle part, so this shouldn't result in any change in behavior.

This fix should work on all OMAP UARTs.  Future patches intended for
the 3.4 merge window will make this workaround conditional on a
"feature" flag, and will use the OMAP36xx+ TX event wakeup support.

Thanks to Kevin Hilman <khilman@ti.com> for mentioning the erratum i291
workaround, which led to the development of this approach.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In the (default) PIO mode, use a one-byte RX FIFO threshold.  The OMAP
UART IP blocks do not appear to be capable of waking the system under
an RX timeout condition.  Since the previous RX FIFO threshold was 16
bytes, this meant that omap-serial.c did not become aware of any
received data until all those bytes arrived or until another UART
interrupt occurred.  This made the serial console and presumably other
serial applications (GPS, serial Bluetooth) unusable or extremely
slow.  A 1-byte RX FIFO threshold also allows the MPU to enter a
low-power consumption state while waiting for the FIFO to fill.

This can be verified using the serial console by comparing the
behavior when "0123456789abcde" is pasted in from another window, with
the behavior when "0123456789abcdef" is pasted in.  Since the former
string is less than sixteen bytes long, the string is not echoed for
some time, while the latter string is echoed immediately.

DMA operation is unaffected by this patch.

Thanks to Russell King - ARM Linux <linux@arm.linux.org.uk> for some
additional information on the standard behavior of the RX timeout
event, which was used to improve this commit description.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Govindraj Raja <govindraj.r@ti.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

_parse_integer() does one or two division instructions (which are slow)
per digit parsed to perform the overflow check.

Furthermore, these are particularly expensive examples of division
instruction as the number of clock cycles required to complete them may
go up with the position of the most significant set bit in the dividend:

	if (*res > div_u64(ULLONG_MAX - val, base))

which is as maximal as possible.

Worse, on 32-bit arches, more than one of these division instructions
may be required per digit.

So, assuming we don't support a base of more than 16, skip the check if the
top nibble of the result is not set at this point.
Signed-off-by: David Howells <dhowells@redhat.com>
[ Changed it to not dereference the pointer all the time - even if the
  compiler can and does optimize it away, the code just looks cleaner.
  And edited the top nybble test slightly to make the code generated on
  x86-64 better in the loop - test against a hoisted constant instead of
  shifting and testing the result ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In commit aeb5032b, a dependency on IRQ_DOMAIN was added, which causes
regressions on previously working setups: a previously working non-DT
kernel configuration now loses its PMIC support.  The lack of PMIC
support in turn causes the loss of other functionality the kernel had.

This dependency was added because the driver now registers its
interrupts with the IRQ domain code, presumably to prevent a build error.

The result is that OMAP3 oopses in the vp.c code (fixed by a previous
commit) due to the lack of PMIC support.

However, even with IRQ_DOMAIN enabled, the driver oopses:

Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] SMP
Modules linked in:
CPU: 1    Not tainted  (3.3.0-rc2+ #271)
PC is at irq_domain_add+0x1c/0x134
LR is at twl_probe+0xd0/0x370
pc : [<c007bad0>]    lr : [<c029baac>]    psr: 00000113
sp : df843c48  ip : df843c68  fp : df843c64
r10: c02b93e4  r9 : 00000000  r8 : c029b9dc
r7 : df9d8a00  r6 : c03bef90  r5 : 00000000  r4 : c03f5240
r3 : 00000000  r2 : c03f5240  r1 : 00000015  r0 : c03f5240
Flags: nzcv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
Control: 10c5387d  Table: 8000404a  DAC: 00000015
Process swapper/0 (pid: 1, stack limit = 0xdf8422f0)
Stack: (0xdf843c48 to 0xdf844000)
3c40:                   00000014 00000170 00000014 c03bef90 df843c9c df843c68
3c60: c029baac c007bac0 00000000 df9d8a20 00000001 c03cd238 c02b93e4 df9d8a20
3c80: df9d8a04 df9d8a00 c029b9dc df8cae08 df843cc4 df843ca0 c01eee70 c029b9e8
...
Backtrace:
[<c007bab4>] (irq_domain_add+0x0/0x134) from [<c029baac>] (twl_probe+0xd0/0x370)
 r6:c03bef90 r5:00000014 r4:00000170
[<c029b9dc>] (twl_probe+0x0/0x370) from [<c01eee70>] (i2c_device_probe+0xb0/0xe4)
[<c01eedc0>] (i2c_device_probe+0x0/0xe4) from [<c01d1f34>] (really_probe+0xa0/0x178)
 r8:df8f0070 r7:c03cd238 r6:df9d8a20 r5:df9d8a20 r4:df9d8a20
[<c01d1e94>] (really_probe+0x0/0x178) from [<c01d205c>] (driver_probe_device+0x50/0x68)
 r7:df843d18 r6:df9d8a20 r5:c03cd238 r4:df9d8a20
[<c01d200c>] (driver_probe_device+0x0/0x68) from [<c01d2148>] (__device_attach+0x44/0x48)
 r5:df9d8a20 r4:c03cd238
[<c01d2104>] (__device_attach+0x0/0x48) from [<c01d0840>] (bus_for_each_drv+0x58/0x98)
 r5:c01d2104 r4:00000000
[<c01d07e8>] (bus_for_each_drv+0x0/0x98) from [<c01d21f8>] (device_attach+0x80/0xac)
 r7:df9d8a28 r6:df9d8a54 r5:c03cd978 r4:df9d8a20
[<c01d2178>] (device_attach+0x0/0xac) from [<c01d1430>] (bus_probe_device+0x34/0xa4)
 r6:df9d8a20 r5:c03cd978 r4:df9d8a20
[<c01d13fc>] (bus_probe_device+0x0/0xa4) from [<c01cffb0>] (device_add+0x2a0/0x420)
 r6:00000000 r5:df9d8a20 r4:df9d8a20
[<c01cfd10>] (device_add+0x0/0x420) from [<c01d0150>] (device_register+0x20/0x24)
 r8:df9d8a00 r7:df9d8a04 r6:df8f0048 r5:df9d8a00 r4:df9d8a20
[<c01d0130>] (device_register+0x0/0x24) from [<c01ef8d4>] (i2c_new_device+0x118/0x180)
 r4:df9d8a20
[<c01ef7bc>] (i2c_new_device+0x0/0x180) from [<c01efc88>] (i2c_register_adapter+0x140/0x204)
 r8:c03cd970 r7:00000000 r6:df8f0070 r5:df8a6300 r4:df8f0048
[<c01efb48>] (i2c_register_adapter+0x0/0x204) from [<c01efe9c>] (i2c_add_numbered_adapter+0xb4/0xcc)
 r8:df8a4c54 r7:df8cae00 r6:df843e2c r5:df8f0048 r4:00000000
[<c01efde8>] (i2c_add_numbered_adapter+0x0/0xcc) from [<c029ce1c>] (omap_i2c_probe+0x2f8/0x3b4)
 r6:00000000 r5:df8f0000 r4:df8f0070
[<c029cb24>] (omap_i2c_probe+0x0/0x3b4) from [<c01d3484>] (platform_drv_probe+0x20/0x24)
[<c01d3464>] (platform_drv_probe+0x0/0x24) from [<c01d1f34>] (really_probe+0xa0/0x178)
[<c01d1e94>] (really_probe+0x0/0x178) from [<c01d205c>] (driver_probe_device+0x50/0x68)
 r7:df843ef0 r6:c03cdb2c r5:c03cdb2c r4:df8cae08
[<c01d200c>] (driver_probe_device+0x0/0x68) from [<c01d20e0>] (__driver_attach+0x6c/0x90)
 r5:df8cae3c r4:df8cae08
[<c01d2074>] (__driver_attach+0x0/0x90) from [<c01d08d8>] (bus_for_each_dev+0x58/0x98)
 r6:c03cdb2c r5:c01d2074 r4:00000000
[<c01d0880>] (bus_for_each_dev+0x0/0x98) from [<c01d1d80>] (driver_attach+0x20/0x28)
 r7:df880b80 r6:c03cdb2c r5:c03cdb2c r4:c0394f28
[<c01d1d60>] (driver_attach+0x0/0x28) from [<c01d115c>] (bus_add_driver+0xb4/0x230)
[<c01d10a8>] (bus_add_driver+0x0/0x230) from [<c01d278c>] (driver_register+0xc8/0x154)
[<c01d26c4>] (driver_register+0x0/0x154) from [<c01d37e4>] (platform_driver_register+0x4c/0x60)
 r8:00000000 r7:00000013 r6:c00384c8 r5:c0395180 r4:c0394f28
[<c01d3798>] (platform_driver_register+0x0/0x60) from [<c038626c>] (omap_i2c_init_driver+0x14/0x1c)
[<c0386258>] (omap_i2c_init_driver+0x0/0x1c) from [<c00087b8>] (do_one_initcall+0x9c/0x164)
[<c000871c>] (do_one_initcall+0x0/0x164) from [<c036c2f4>] (kernel_init+0x90/0x138)
[<c036c264>] (kernel_init+0x0/0x138) from [<c00384c8>] (do_exit+0x0/0x2ec)
 r5:c036c264 r4:00000000
<0>Code: e24dd004 e5903014 e1a04000 e5905010 (e5933000)
<4>---[ end trace 1b75b31a2719ed1c ]---

This happens because we try to register an IRQ domain with a NULL ops
structure, and the first thing irq_domain_add() does is try to
dereference this ops structure.

So, fix the problem by getting rid of the incorrect OF_IRQ ifdef and
wrapping the IRQ domain bits of the driver with an IRQ_DOMAIN ifdef
instead.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

When a PMIC is not found, this driver is unable to obtain its
'vdds_dsi_reg' regulator.  Even through its initialization function
fails, other code still calls its enable function, which fails to
check whether it has this regulator before asking for it to be enabled.

This fixes the oops, however a better fix would be to sort out the
upper layers to prevent them calling into a module which failed to
initialize.

Unable to handle kernel NULL pointer dereference at virtual address 00000038
pgd = c0004000
[00000038] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT
Modules linked in:
CPU: 0    Not tainted  (3.3.0-rc2+ #228)
PC is at regulator_enable+0x10/0x70
LR is at omapdss_dpi_display_enable+0x54/0x15c
pc : [<c01b9a08>]    lr : [<c01af994>]    psr: 60000013
sp : c181fd90  ip : c181fdb0  fp : c181fdac
r10: c042eff0  r9 : 00000060  r8 : c044a164
r7 : c042c0e4  r6 : c042bd60  r5 : 00000000  r4 : c042bd60
r3 : c084de48  r2 : c181e000  r1 : c042bd60  r0 : 00000000
Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
Control: 10c5387d  Table: 80004019  DAC: 00000015
Process swapper (pid: 1, stack limit = 0xc181e2e8)
Stack: (0xc181fd90 to 0xc1820000)
fd80:                                     c001754c c042bd60 00000000 c042bd60
fda0: c181fdcc c181fdb0 c01af994 c01b9a04 c0016104 c042bd60 c042bd60 c044a338
fdc0: c181fdec c181fdd0 c01b5ed0 c01af94c c042bd60 c042bd60 c1aa8000 c1aa8a0c
fde0: c181fe04 c181fdf0 c01b5f54 c01b5ea8 c02fc18c c042bd60 c181fe3c c181fe08
fe00: c01b2a18 c01b5f48 c01aed14 c02fc160 c01df8ec 00000002 c042bd60 00000003
fe20: c042bd60 c1aa8000 c1aa8a0c c042eff8 c181fe84 c181fe40 c01b3874 c01b29fc
fe40: c042eff8 00000000 c042f000 c0449db8 c044ed78 00000000 c181fe74 c042eff8
fe60: c042eff8 c0449db8 c0449db8 c044ed78 00000000 00000000 c181fe94 c181fe88
fe80: c01e452c c01b35e8 c181feb4 c181fe98 c01e2fdc c01e4518 c042eff8 c0449db8
fea0: c0449db8 c181fef0 c181fecc c181feb8 c01e3104 c01e2f48 c042eff8 c042f02c
fec0: c181feec c181fed0 c01e3190 c01e30c0 c01e311c 00000000 c01e311c c0449db8
fee0: c181ff14 c181fef0 c01e1998 c01e3128 c18330a8 c1892290 c04165e8 c0449db8
ff00: c0449db8 c1ab60c0 c181ff24 c181ff18 c01e2e28 c01e194c c181ff54 c181ff28
ff20: c01e2218 c01e2e14 c039afed c181ff38 c04165e8 c041660c c0449db8 00000013
ff40: 00000000 c03ffdb8 c181ff7c c181ff58 c01e384c c01e217c c181ff7c c04165e8
ff60: c041660c c003a37c 00000013 00000000 c181ff8c c181ff80 c01e488c c01e3790
ff80: c181ff9c c181ff90 c03ffdcc c01e484c c181ffdc c181ffa0 c0008798 c03ffdc4
ffa0: c181ffc4 c181ffb0 c0056440 c0187810 c003a37c c04165e8 c041660c c003a37c
ffc0: 00000013 00000000 00000000 00000000 c181fff4 c181ffe0 c03ea284 c0008708
ffe0: 00000000 c03ea208 00000000 c181fff8 c003a37c c03ea214 1073cec0 01f7ee08
Backtrace:
[<c01b99f8>] (regulator_enable+0x0/0x70) from [<c01af994>] (omapdss_dpi_display_enable+0x54/0x15c)
 r6:c042bd60 r5:00000000 r4:c042bd60
[<c01af940>] (omapdss_dpi_display_enable+0x0/0x15c) from [<c01b5ed0>] (generic_dpi_panel_power_on+0x34/0x78)
 r6:c044a338 r5:c042bd60 r4:c042bd60
[<c01b5e9c>] (generic_dpi_panel_power_on+0x0/0x78) from [<c01b5f54>] (generic_dpi_panel_enable+0x18/0x28)
 r7:c1aa8a0c r6:c1aa8000 r5:c042bd60 r4:c042bd60
[<c01b5f3c>] (generic_dpi_panel_enable+0x0/0x28) from [<c01b2a18>] (omapfb_init_display+0x28/0x150)
 r4:c042bd60
[<c01b29f0>] (omapfb_init_display+0x0/0x150) from [<c01b3874>] (omapfb_probe+0x298/0x318)
 r8:c042eff8 r7:c1aa8a0c r6:c1aa8000 r5:c042bd60 r4:00000003
[<c01b35dc>] (omapfb_probe+0x0/0x318) from [<c01e452c>] (platform_drv_probe+0x20/0x24)
[<c01e450c>] (platform_drv_probe+0x0/0x24) from [<c01e2fdc>] (really_probe+0xa0/0x178)
[<c01e2f3c>] (really_probe+0x0/0x178) from [<c01e3104>] (driver_probe_device+0x50/0x68)
 r7:c181fef0 r6:c0449db8 r5:c0449db8 r4:c042eff8
[<c01e30b4>] (driver_probe_device+0x0/0x68) from [<c01e3190>] (__driver_attach+0x74/0x98)
 r5:c042f02c r4:c042eff8
[<c01e311c>] (__driver_attach+0x0/0x98) from [<c01e1998>] (bus_for_each_dev+0x58/0x98)
 r6:c0449db8 r5:c01e311c r4:00000000
[<c01e1940>] (bus_for_each_dev+0x0/0x98) from [<c01e2e28>] (driver_attach+0x20/0x28)
 r7:c1ab60c0 r6:c0449db8 r5:c0449db8 r4:c04165e8
[<c01e2e08>] (driver_attach+0x0/0x28) from [<c01e2218>] (bus_add_driver+0xa8/0x22c)
[<c01e2170>] (bus_add_driver+0x0/0x22c) from [<c01e384c>] (driver_register+0xc8/0x154)
[<c01e3784>] (driver_register+0x0/0x154) from [<c01e488c>] (platform_driver_register+0x4c/0x60)
 r8:00000000 r7:00000013 r6:c003a37c r5:c041660c r4:c04165e8
[<c01e4840>] (platform_driver_register+0x0/0x60) from [<c03ffdcc>] (omapfb_init+0x14/0x34)
[<c03ffdb8>] (omapfb_init+0x0/0x34) from [<c0008798>] (do_one_initcall+0x9c/0x164)
[<c00086fc>] (do_one_initcall+0x0/0x164) from [<c03ea284>] (kernel_init+0x7c/0x120)
[<c03ea208>] (kernel_init+0x0/0x120) from [<c003a37c>] (do_exit+0x0/0x2d8)
 r5:c03ea208 r4:00000000
Code: e1a0c00d e92dd870 e24cb004 e24dd004 (e5906038)
---[ end trace 9e2474c2e193b223 ]---
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

When the PMIC is not found, voltdm->pmic will be NULL.  vp.c's
initialization function tries to dereferences this, which causes an
oops:

Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT
Modules linked in:
CPU: 0    Not tainted  (3.3.0-rc2+ #204)
PC is at omap_vp_init+0x5c/0x15c
LR is at omap_vp_init+0x58/0x15c
pc : [<c03db880>]    lr : [<c03db87c>]    psr: 60000013
sp : c181ff30  ip : c181ff68  fp : c181ff64
r10: c0407808  r9 : c040786c  r8 : c0407814
r7 : c0026868  r6 : c00264fc  r5 : c040ad6c  r4 : 00000000
r3 : 00000040  r2 : 000032c8  r1 : 0000fa00  r0 : 000032c8
Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
Control: 10c5387d  Table: 80004019  DAC: 00000015
Process swapper (pid: 1, stack limit = 0xc181e2e8)
Stack: (0xc181ff30 to 0xc1820000)
ff20:                                     c0381d00 c02e9c6d c0383582 c040786c
ff40: c040ad6c c00264fc c0026868 c0407814 00000000 c03d9de4 c181ff8c c181ff68
ff60: c03db448 c03db830 c02e982c c03fdfb8 c03fe004 c0039988 00000013 00000000
ff80: c181ff9c c181ff90 c03d9df8 c03db390 c181ffdc c181ffa0 c0008798 c03d9df0
ffa0: c181ffc4 c181ffb0 c0055a44 c0187050 c0039988 c03fdfb8 c03fe004 c0039988
ffc0: 00000013 00000000 00000000 00000000 c181fff4 c181ffe0 c03d1284 c0008708
ffe0: 00000000 c03d1208 00000000 c181fff8 c0039988 c03d1214 1077ce40 01f7ee08
Backtrace:
[<c03db824>] (omap_vp_init+0x0/0x15c) from [<c03db448>] (omap_voltage_late_init+0xc4/0xfc)
[<c03db384>] (omap_voltage_late_init+0x0/0xfc) from [<c03d9df8>] (omap2_common_pm_late_init+0x14/0x54)
 r8:00000000 r7:00000013 r6:c0039988 r5:c03fe004 r4:c03fdfb8
[<c03d9de4>] (omap2_common_pm_late_init+0x0/0x54) from [<c0008798>] (do_one_initcall+0x9c/0x164)
[<c00086fc>] (do_one_initcall+0x0/0x164) from [<c03d1284>] (kernel_init+0x7c/0x120)
[<c03d1208>] (kernel_init+0x0/0x120) from [<c0039988>] (do_exit+0x0/0x2cc)
 r5:c03d1208 r4:00000000
Code: e5ca300b e5900034 ebf69027 e5994024 (e5941000)
---[ end trace aed617dddaf32c3d ]---
Kernel panic - not syncing: Attempted to kill init!
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The ARM kernel uses undefined instructions to implement
BUG/BUG_ON(). This leads to problems where people don't read one
line above the Oops message and see the "kernel BUG at ..."
message and so they wrongly assume the kernel has hit an
undefined instruction.

Instead of printing:

 Internal error: Oops - undefined instruction: 0 [#1] PREEMPT SMP

print

 Internal error: Oops - BUG: 0 [#1] PREEMPT SMP

This should prevent people from thinking the BUG_ON was an
undefined instruction when it was actually intentional.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

armv7's flush_cache_all() flushes caches via set/way. To
determine the cache attributes (line size, number of sets,
etc.) the assembly first writes the CSSELR register to select a
cache level and then reads the CCSIDR register. The CSSELR register
is banked per-cpu and is used to determine which cache level CCSIDR
reads. If the task is migrated between when the CSSELR is written and
the CCSIDR is read the CCSIDR value may be for an unexpected cache
level (for example L1 instead of L2) and incorrect cache flushing
could occur.

Disable interrupts across the write and read so that the correct
cache attributes are read and used for the cache flushing
routine. We disable interrupts instead of disabling preemption
because the critical section is only 3 instructions and we want
to call v7_dcache_flush_all from __v7_setup which doesn't have a
full kernel stack with a struct thread_info.

This fixes a problem we see in scm_call() when flush_cache_all()
is called from preemptible context and sometimes the L2 cache is
not properly flushed out.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

With an admittedly exotic choice of configuration options
(CC_OPTIMIZE_FOR_SIZE, THUMB2, some other size-minimizing ones)
and compiler, the proc_info table can end up being misaligned,
and the kernel being unbootable (Error: unrecognized/unsupported
processor variant).

Forcing the alignement to 4 bytes in the linker script fixes the
issue.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

If the number of tx/rx queues changes the ethtool ioctl
ETHTOOL_GSTATS may overrun the userspace buffer. This
occurs because the general practice in user space to
query stats is to issue a ETHTOOL_GSSET cmd to learn the
buffer size needed, allocate the buffer, then call
ETHTOOL_GSTIRNGS and ETHTOOL_GSTATS. If the number of
real_num_queues is changed or flow control attributes
are changed after ETHTOOL_GSSET but before the
ETHTOOL_GSTRINGS/ETHTOOL_GSTATS a user space buffer
overrun occurs.

To fix the overrun always return the max buffer size
needed from get_sset_count() then return all strings
and stats from get_strings()/get_ethtool_stats().

This _will_ change the output from the ioctl() call
which could break applications and script parsing in
theory. I believe these changes should not break existing
tools because the only changes will be more {tx|rx}_queues
and the {tx|rx}_pb_* stats will always be returned.
Existing scripts already need to handle changing number
of queues because this occurs today depending on system
and current features. The {tx|rx}_pb_* stats are at the
end of the output and should be handled by scripts today
regardless.

Finally get_ethtool_stats and get_strings are free-form
outputs tools parsing these outputs should be defensive
anyways. In the end these updates are better then
having a tool segfault because of a buffer overrun.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Users expect the up2tc mapping to be maintained across a DCB
enable/disable/enable transition. And since we maintain all
the other DCB attributes we should do this for up2tc mappings
as well just to be consistent. Also without this we break
user space applications that expect this to occur that
previously worked.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

If the netdev is already in NETREG_UNREGISTERING/_UNREGISTERED state, do not
update the real num tx queues. netdev_queue_update_kobjects() is already
called via remove_queue_kobjects() at NETREG_UNREGISTERING time. So, when
upper layer driver, e.g., FCoE protocol stack is monitoring the netdev
event of NETDEV_UNREGISTER and calls back to LLD ndo_fcoe_disable() to remove
extra queues allocated for FCoE, the associated txq sysfs kobjects are already
removed, and trying to update the real num queues would cause something like
below:

...
PID: 25138  TASK: ffff88021e64c440  CPU: 3   COMMAND: "kworker/3:3"
 #0 [ffff88021f007760] machine_kexec at ffffffff810226d9
 #1 [ffff88021f0077d0] crash_kexec at ffffffff81089d2d
 #2 [ffff88021f0078a0] oops_end at ffffffff813bca78
 #3 [ffff88021f0078d0] no_context at ffffffff81029e72
 #4 [ffff88021f007920] __bad_area_nosemaphore at ffffffff8102a155
 #5 [ffff88021f0079f0] bad_area_nosemaphore at ffffffff8102a23e
 #6 [ffff88021f007a00] do_page_fault at ffffffff813bf32e
 #7 [ffff88021f007b10] page_fault at ffffffff813bc045
    [exception RIP: sysfs_find_dirent+17]
    RIP: ffffffff81178611  RSP: ffff88021f007bc0  RFLAGS: 00010246
    RAX: ffff88021e64c440  RBX: ffffffff8156cc63  RCX: 0000000000000004
    RDX: ffffffff8156cc63  RSI: 0000000000000000  RDI: 0000000000000000
    RBP: ffff88021f007be0   R8: 0000000000000004   R9: 0000000000000008
    R10: ffffffff816fed00  R11: 0000000000000004  R12: 0000000000000000
    R13: ffffffff8156cc63  R14: 0000000000000000  R15: ffff8802222a0000
    ORIG_RAX: ffffffffffffffff  CS: 0010  SS: 0018
 #8 [ffff88021f007be8] sysfs_get_dirent at ffffffff81178c07
 #9 [ffff88021f007c18] sysfs_remove_group at ffffffff8117ac27
#10 [ffff88021f007c48] netdev_queue_update_kobjects at ffffffff813178f9
#11 [ffff88021f007c88] netif_set_real_num_tx_queues at ffffffff81303e38
#12 [ffff88021f007cc8] ixgbe_set_num_queues at ffffffffa0249763 [ixgbe]
#13 [ffff88021f007cf8] ixgbe_init_interrupt_scheme at ffffffffa024ea89 [ixgbe]
#14 [ffff88021f007d48] ixgbe_fcoe_disable at ffffffffa0267113 [ixgbe]
#15 [ffff88021f007d68] vlan_dev_fcoe_disable at ffffffffa014fef5 [8021q]
#16 [ffff88021f007d78] fcoe_interface_cleanup at ffffffffa02b7dfd [fcoe]
#17 [ffff88021f007df8] fcoe_destroy_work at ffffffffa02b7f08 [fcoe]
#18 [ffff88021f007e18] process_one_work at ffffffff8105d7ca
#19 [ffff88021f007e68] worker_thread at ffffffff81060513
#20 [ffff88021f007ee8] kthread at ffffffff810648b6
#21 [ffff88021f007f48] kernel_thread_helper at ffffffff813c40f4
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>