- 29 Apr, 2015 3 commits
-
-
Tom Herbert authored
commit 3dfb0534 upstream. Call checksum_complete_unset in PPP receive to discard checksum-complete value. PPP does not pull checksum for headers and also modifies packet as in VJ compression. Signed-off-by:
Tom Herbert <tom@herbertland.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Tom Herbert authored
commit 4e18b9ad upstream. This function changes ip_summed to CHECKSUM_NONE if CHECKSUM_COMPLETE is set. This is called to discard checksum-complete when packet is being modified and checksum is not pulled for headers in a layer. Signed-off-by:
-
Sebastian Pöhn authored
commit 2ab95749 upstream. Initial discussion was: [FYI] xfrm: Don't lookup sk_policy for timewait sockets Forwarded frames should not have a socket attached. Especially tw sockets will lead to panics later-on in the stack. This was observed with TPROXY assigning a tw socket and broken policy routing (misconfigured). As a result frame enters forwarding path instead of input. We cannot solve this in TPROXY as it cannot know that policy routing is broken. v2: Remove useless comment Signed-off-by:
Sebastian Poehn <sebastian.poehn@gmail.com> Signed-off-by:
-
- 28 Apr, 2015 1 commit
-
-
Jann Horn authored
commit 8b01fc86 upstream. This prevents a race between chown() and execve(), where chowning a setuid-user binary to root would momentarily make the binary setuid root. This patch was mostly written by Linus Torvalds. Signed-off-by:
Jann Horn <jann@thejh.net> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> [ luis: backported to 3.16: - relaced task_no_new_privs() by current->no_new_privs - replaced READ_ONCE() by ACCESS_ONCE() ] Signed-off-by:
-
- 27 Apr, 2015 33 commits
-
-
Omar Sandoval authored
commit 6f30b7e3 upstream. Commit 4f579ae7 (ext4: fix punch hole on files with indirect mapping) rewrote FALLOC_FL_PUNCH_HOLE for ext4 files with indirect mapping. However, there are bugs in several corner cases. This fixes 5 distinct bugs: 1. When there is at least one entire level of indirection between the start and end of the punch range and the end of the punch range is the first block of its level, we can't return early; we have to free the intervening levels. 2. When the end is at a higher level of indirection than the start and ext4_find_shared returns a top branch for the end, we still need to free the rest of the shared branch it returns; we can't decrement partial2. 3. When a punch happens within one level of indirection, we need to converge on an indirect block that contains the start and end. However, because the branches returned from ext4_find_shared do not necessarily start at the same level (e.g., the partial2 chain will be shallower if the last block occurs at the beginning of an indirect group), the walk of the two chains can end up "missing" each other and freeing a bunch of extra blocks in the process. This mismatch can be handled by first making sure that the chains are at the same level, then walking them together until they converge. 4. When the punch happens within one level of indirection and ext4_find_shared returns a top branch for the start, we must free it, but only if the end does not occur within that branch. 5. When the punch happens within one level of indirection and ext4_find_shared returns a top branch for the end, then we shouldn't free the block referenced by the end of the returned chain (this mirrors the different levels case). Signed-off-by:
Omar Sandoval <osandov@osandov.com> Signed-off-by:
-
Mike Christie authored
commit b815fc12 upstream. This fixes a oops due to a double list add when adding a reject PDU for iscsit_allocate_iovecs allocation failures. The cmd has already been added to the conn_cmd_list in iscsit_setup_scsi_cmd, so this has us call iscsit_reject_cmd. Note that for ERL0 the reject PDU is not actually sent, so this patch is not completely tested. Just verified we do not oops. The problem is the add reject functions return -1 which is returned all the way up to iscsi_target_rx_thread which for ERL0 will drop the connection. Signed-off-by:
Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Dmitry M. Fedin authored
commit 3dc8523f upstream. Adds an entry for Creative USB X-Fi to the rc_config array in mixer_quirks.c to allow use of volume knob on the device. Adds support for newer X-Fi Pro card, known as "Model No. SB1095" with USB ID "041e:3237" Signed-off-by:
Dmitry M. Fedin <dmitry.fedin@gmail.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Al Viro authored
commit 64b4e252 upstream. "ocfs2 syncs the wrong range" had been broken; prior to it the code was doing the wrong thing in case of O_APPEND, all right, but _after_ it we were syncing the wrong range in 100% cases. *ppos, aka iocb->ki_pos is incremented prior to that point, so we are always doing sync on the area _after_ the one we'd written to. Spotted by Joseph Qi <joseph.qi@huawei.com> back in January; unfortunately, I'd missed his mail back then ;-/ Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Takashi Iwai authored
commit cc7016ab upstream. Some BIOS version of Fujitsu Lifebook T731 seems to set up the headphone pin (0x21) without the assoc number 0x0f while it's set only to the output on the docking port (0x1a). With the recent commit [03ad6a8c: ALSA: hda - Fix "PCM" name being used on one DAC when there are two DACs], this resulted in the weird mixer element mapping where the headphone on the laptop is assigned as a shared volume with the speaker and the docking port is assigned as an individual headphone. This patch improves the situation by correcting the headphone pin config to the more appropriate value. Reported-and-tested-by:
Taylor Smock <smocktaylor@gmail.com> Signed-off-by:
-
Bart Van Assche authored
commit bba0bdd7 upstream. SCSI transport drivers and SCSI LLDs block a SCSI device if the transport layer is not operational. This means that in this state no requests should be processed, even if the REQ_PREEMPT flag has been set. This patch avoids that a rescan shortly after a cable pull sporadically triggers the following kernel oops: BUG: unable to handle kernel paging request at ffffc9001a6bc084 IP: [<ffffffffa04e08f2>] mlx4_ib_post_send+0xd2/0xb30 [mlx4_ib] Process rescan-scsi-bus (pid: 9241, threadinfo ffff88053484a000, task ffff880534aae100) Call Trace: [<ffffffffa0718135>] srp_post_send+0x65/0x70 [ib_srp] [<ffffffffa071b9df>] srp_queuecommand+0x1cf/0x3e0 [ib_srp] [<ffffffffa0001ff1>] scsi_dispatch_cmd+0x101/0x280 [scsi_mod] [<ffffffffa0009ad1>] scsi_request_fn+0x411/0x4d0 [scsi_mod] [<ffffffff81223b37>] __blk_run_queue+0x27/0x30 [<ffffffff8122a8d2>] blk_execute_rq_nowait+0x82/0x110 [<ffffffff8122a9c2>] blk_execute_rq+0x62/0xf0 [<ffffffffa000b0e8>] scsi_execute+0xe8/0x190 [scsi_mod] [<ffffffffa000b2f3>] scsi_execute_req+0xa3/0x130 [scsi_mod] [<ffffffffa000c1aa>] scsi_probe_lun+0x17a/0x450 [scsi_mod] [<ffffffffa000ce86>] scsi_probe_and_add_lun+0x156/0x480 [scsi_mod] [<ffffffffa000dc2f>] __scsi_scan_target+0xdf/0x1f0 [scsi_mod] [<ffffffffa000dfa3>] scsi_scan_host_selected+0x183/0x1c0 [scsi_mod] [<ffffffffa000edfb>] scsi_scan+0xdb/0xe0 [scsi_mod] [<ffffffffa000ee13>] store_scan+0x13/0x20 [scsi_mod] [<ffffffff811c8d9b>] sysfs_write_file+0xcb/0x160 [<ffffffff811589de>] vfs_write+0xce/0x140 [<ffffffff81158b53>] sys_write+0x53/0xa0 [<ffffffff81464592>] system_call_fastpath+0x16/0x1b [<00007f611c9d9300>] 0x7f611c9d92ff Reported-by:
Max Gurtuvoy <maxg@mellanox.com> Signed-off-by:
Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by:
James Bottomley <JBottomley@Odin.com> Signed-off-by:
-
John Soni Jose authored
commit 2e7cee02 upstream. Kernel panic was happening as iscsi_host_remove() was called on a host which was not yet added. Signed-off-by:
John Soni Jose <sony.john-n@emulex.com> Reviewed-by:
-
Takashi Sakamoto authored
commit a053fc31 upstream. Some M-Audio devices require to receive bootup command just after powering on, while codes in BeBoB driver doesn't work properly in big-endian machine because the command should be aligned by little-endian. This commit fixes this bug. This fix should go to stable kernel. Cc: Takayuki Shiroma <t.shiroma.oki@gmail.com> Signed-off-by:
Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by:
-
Kailang Yang authored
commit a59d7199 upstream. Pin sense will active when power pin is wake up. Power pin will not wake up immediately during resume state. Add some delay to wait for power pin activated. Signed-off-by:
Kailang Yang <kailang@realtek.com> Signed-off-by:
-
Jesse Barnes authored
commit 5df0582b upstream. Looks like it was introduced in: commit 650ad970 Author: Imre Deak <imre.deak@intel.com> Date: Fri Apr 18 16:35:02 2014 +0300 drm/i915: vlv: factor out vlv_force_gfx_clock and check for pending force-of but I'm not sure why. It has caused problems for us in the past (see 85250ddf "drm/i915/chv: Remove Wait for a previous gfx force-off" and 8d4eee9c "drm/i915: vlv: increase timeout when forcing on the GFX clock") and doesn't seem to be required, so let's just drop it. References: https://bugs.freedesktop.org/show_bug.cgi?id=89611Signed-off-by:
Jesse Barnes <jbarnes@virtuousgeek.org> Tested-by:
Darren Hart <dvhart@linux.intel.com> Reviewed-by:
Deepak S <deepak.s@linux.intel.com> Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Signed-off-by:
-
Deepak S authored
commit c9c52e24 upstream. On CHV, PUNIT team confirmed that 'VLV_GFX_CLK_STATUS_BIT' is not a sticky bit and it will always be set. So ignore Check for previous Gfx force off during suspend and allow the force clk as part S0ix Sequence Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
-
Jesse Barnes authored
commit 9c25210f upstream. Some BIOSes (e.g. the one on the Minnowboard) don't save/restore this reg. If it's unlocked, we can just restore the previous value, and if it's locked (in case the BIOS re-programmed it for us) the write will be ignored and we'll still have "did it move" sanity check in the PM code to warn us if something is still amiss. References: https://bugs.freedesktop.org/show_bug.cgi?id=89611Signed-off-by:
Imre Deak <imre.deak@intel.com> Reviewed-by:
-
Al Viro authored
commit deeb8525 upstream. If we fail past the aio_setup_ring(), we need to destroy the mapping. We don't need to care about anybody having found ctx, or added requests to it, since the last failure exit is exactly the failure to make ctx visible to lookups. Reproducer (based on one by Joe Mario <jmario@redhat.com>): void count(char *p) { char s[80]; printf("%s: ", p); fflush(stdout); sprintf(s, "/bin/cat /proc/%d/maps|/bin/fgrep -c '/[aio] (deleted)'", getpid()); system(s); } int main() { io_context_t *ctx; int created, limit, i, destroyed; FILE *f; count("before"); if ((f = fopen("/proc/sys/fs/aio-max-nr", "r")) == NULL) perror("opening aio-max-nr"); else if (fscanf(f, "%d", &limit) != 1) fprintf(stderr, "can't parse aio-max-nr\n"); else if ((ctx = calloc(limit, sizeof(io_context_t))) == NULL) perror("allocating aio_context_t array"); else { for (i = 0, created = 0; i < limit; i++) { if (io_setup(1000, ctx + created) == 0) created++; } for (i = 0, destroyed = 0; i < created; i++) if (io_destroy(ctx[i]) == 0) destroyed++; printf("created %d, failed %d, destroyed %d\n", created, limit - created, destroyed); count("after"); } } Found-by:
Joe Mario <jmario@redhat.com> Signed-off-by:
-
Thomas Schlichter authored
commit c7e8bdf5 upstream. Fix a bug that leads to showing the name and description of C-state C0 as "<null>" in sysfs after the ACPI C-states changed (e.g. after AC->DC or DC->AC transition). The function poll_idle_init() in drivers/cpuidle/driver.c initializes the state 0 during cpuidle_register_driver(), so we better do not overwrite it again with '\0' during acpi_processor_cst_has_changed(). Signed-off-by:
Thomas Schlichter <thomas.schlichter@web.de> Reviewed-by:
Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
commit d75e4af1 upstream. Thomas Schlichter reports the following issue on his Samsung NC20: "The C-states C1 and C2 to the OS when connected to AC, and additionally provides the C3 C-state when disconnected from AC. However, the number of C-states shown in sysfs is fixed to the number of C-states present at boot. If I boot with AC connected, I always only see the C-states up to C2 even if I disconnect AC. The reason is commit 130a5f69 (ACPI / cpuidle: remove dev->state_count setting). It removes the update of dev->state_count, but sysfs uses exactly this variable to show the C-states. The fix is to use drv->state_count in sysfs. As this is currently the last user of dev->state_count, this variable can be completely removed." Remove dev->state_count as per the above. Reported-by:
Kyungmin Park <kyungmin.park@samsung.com> Acked-by:
Daniel Lezcano <daniel.lezcano@linaro.org> [ rjw: Changelog ] Signed-off-by:
-
Viresh Kumar authored
commit c75de0ac upstream. All CPUs leaving the first-online CPU are hotplugged out on suspend and and cpufreq core stops managing them. On resume, we need to call cpufreq_update_policy() for this CPU's policy to make sure its frequency is in sync with cpufreq's cached value, as it might have got updated by hardware during suspend/resume. The policies are always added to the top of the policy-list. So, in normal circumstances, CPU 0's policy will be the last one in the list. And so the code checks for the last policy. But there are cases where it will fail. Consider quad-core system, with policy-per core. If CPU0 is hotplugged out and added back again, the last policy will be on CPU1 :( To fix this in a proper way, always look for the policy of the first online CPU. That way we will be sure that we are calling cpufreq_update_policy() for the only CPU that wasn't hotplugged out. Fixes: 2f0aea93 ("cpufreq: suspend governors on system suspend/hibernate") Reported-by:
Saravana Kannan <skannan@codeaurora.org> Signed-off-by:
Viresh Kumar <viresh.kumar@linaro.org> Acked-by:
-
Marek Szyprowski authored
commit 05b676ab upstream. TASK_SIZE is depends on the systems architecture (32 or 64 bits) and it should not be used for defining offset boundary for mmaping buffers for CAPTURE and OUTPUT queues. This patch fixes support for MMAP calls on the CAPTURE queue on 64bit architectures (like ARM64). Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
Kamil Debski <k.debski@samsung.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
-
Hans Verkuil authored
commit ab312030 upstream. The v4l2_dev field of struct video_device must be set correctly. This was never done for this driver, so no video nodes were created anymore. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Dan Carpenter authored
commit bc3b5b47 upstream. I don't have this hardware but it looks like we weren't adding bridge devices as intended. Maybe the bridge is always the last device? Fixes: 05b12500 ("PCI: cpcihp: Iterate over all devices in slot, not functions 0-7") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Acked-by:
Yijing Wang <wangyijing@huawei.com> Signed-off-by:
-
Rasmus Villemoes authored
commit a1b7f2f6 upstream. Commit fab4c256 ("PCI/AER: Add a TLP header print helper") introduced the helper function __print_tlp_header(), but contrary to the intention, the behaviour did change: Since we're taking the address of the parameter t, the first 4 or 8 bytes printed will be the value of the pointer t itself, and the remaining 12 or 8 bytes will be who-knows-what (something from the stack). We want to show the values of the four members of the struct aer_header_log_regs; that can be done without ugly and error-prone casts. On little-endian this should produce the same output as originally intended, and since no-one has complained about getting garbage output so far, I think big-endian should be ok too. Fixes: fab4c256 ("PCI/AER: Add a TLP header print helper") Signed-off-by:
Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by:
Borislav Petkov <bp@suse.de> Signed-off-by:
-
oliver@neukum.org authored
commit a4154577 upstream. This device disconnects every 60s without X Signed-off-by:
Oliver Neukum <oliver@neukum.org> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Anton Nayshtut authored
commit f5e2dc5d upstream. Before commit 3900f290 ("bonding: slight optimizztion for bond_slave_override()") the override logic was to send packets with non-zero queue_id through the slave with corresponding queue_id, under two conditions only - if the slave can transmit and it's up. The above mentioned commit changed this logic by introducing an additional condition - whether the bond is active (indirectly, using the slave_can_tx and later - bond_is_active_slave), that prevents the user from implementing more complex policies according to the Documentation/networking/bonding.txt. Signed-off-by:
Anton Nayshtut <anton@swortex.com> Signed-off-by:
Alexey Bogoslavsky <alexey@swortex.com> Signed-off-by:
Andy Gospodarek <gospo@cumulusnetworks.com> Signed-off-by:
-
Ben Hutchings authored
commit 7a1e890e upstream. cdc_ncm disagrees with usbnet about how much framing overhead should be counted in the tx_bytes statistics, and tries 'fix' this by decrementing tx_bytes on the transmit path. But statistics must never be decremented except due to roll-over; this will thoroughly confuse user-space. Also, tx_bytes is only incremented by usbnet in the completion path. Fix this by requiring drivers that set FLAG_MULTI_FRAME to set a tx_bytes delta along with the tx_packets count. Fixes: beeecd42 ("net: cdc_ncm/cdc_mbim: adding NCM protocol statistics") Signed-off-by:
Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Ben Hutchings authored
commit 1e9e39f4 upstream. Currently the usbnet core does not update the tx_packets statistic for drivers with FLAG_MULTI_PACKET and there is no hook in the TX completion path where they could do this. cdc_ncm and dependent drivers are bumping tx_packets stat on the transmit path while asix and sr9800 aren't updating it at all. Add a packet count in struct skb_data so these drivers can fill it in, initialise it to 1 for other drivers, and add the packet count to the tx_packets statistic on completion. Signed-off-by:
-
Eric Dumazet authored
commit b50edd78 upstream. I noticed tcpdump was giving funky timestamps for locally generated SYNACK messages on loopback interface. 11:42:46.938990 IP 127.0.0.1.48245 > 127.0.0.2.23850: S 945476042:945476042(0) win 43690 <mss 65495,nop,nop,sackOK,nop,wscale 7> 20:28:58.502209 IP 127.0.0.2.23850 > 127.0.0.1.48245: S 3160535375:3160535375(0) ack 945476043 win 43690 <mss 65495,nop,nop,sackOK,nop,wscale 7> This is because we need to clear skb->tstamp before entering lower stack, otherwise net_timestamp_check() does not set skb->tstamp. Fixes: 7faee5c0 ("tcp: remove TCP_SKB_CB(skb)->when") Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
hannes@stressinduktion.org authored
commit f60e5990 upstream. We should not consult skb->sk for output decisions in xmit recursion levels > 0 in the stack. Otherwise local socket settings could influence the result of e.g. tunnel encapsulation process. ipv6 does not conform with this in three places: 1) ip6_fragment: we do consult ipv6_npinfo for frag_size 2) sk_mc_loop in ipv6 uses skb->sk and checks if we should loop the packet back to the local socket 3) ip6_skb_dst_mtu could query the settings from the user socket and force a wrong MTU Furthermore: In sk_mc_loop we could potentially land in WARN_ON(1) if we use a PF_PACKET socket ontop of an IPv6-backed vxlan device. Reuse xmit_recursion as we are currently only interested in protecting tunnel devices. Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
Michal Kubeček authored
commit d0c294c5 upstream. On s390x, gcc 4.8 compiles this part of tcp_v6_early_demux() struct dst_entry *dst = sk->sk_rx_dst; if (dst) dst = dst_check(dst, inet6_sk(sk)->rx_dst_cookie); to code reading sk->sk_rx_dst twice, once for the test and once for the argument of ip6_dst_check() (dst_check() is inline). This allows ip6_dst_check() to be called with null first argument, causing a crash. Protect sk->sk_rx_dst access by READ_ONCE() both in IPv4 and IPv6 TCP early demux code. Fixes: 41063e9d ("ipv4: Early TCP socket demux.") Fixes: c7109986 ("ipv6: Early TCP socket demux") Signed-off-by:
Michal Kubecek <mkubecek@suse.cz> Acked-by:
-
Nadav Amit authored
commit f210f757 upstream. apic_find_highest_irr assumes irr_pending is set if any vector in APIC_IRR is set. If this assumption is broken and apicv is disabled, the injection of interrupts may be deferred until another interrupt is delivered to the guest. Ultimately, if no other interrupt should be injected to that vCPU, the pending interrupt may be lost. commit 56cc2406 ("KVM: nVMX: fix "acknowledge interrupt on exit" when APICv is in use") changed the behavior of apic_clear_irr so irr_pending is cleared after setting APIC_IRR vector. After this commit, if apic_set_irr and apic_clear_irr run simultaneously, a race may occur, resulting in APIC_IRR vector set, and irr_pending cleared. In the following example, assume a single vector is set in IRR prior to calling apic_clear_irr: apic_set_irr apic_clear_irr ------------ -------------- apic->irr_pending = true; apic_clear_vector(...); vec = apic_search_irr(apic); // => vec == -1 apic_set_vector(...); apic->irr_pending = (vec != -1); // => apic->irr_pending == false Nonetheless, it appears the race might even occur prior to this commit: apic_set_irr apic_clear_irr ------------ -------------- apic->irr_pending = true; apic->irr_pending = false; apic_clear_vector(...); if (apic_search_irr(apic) != -1) apic->irr_pending = true; // => apic->irr_pending == false apic_set_vector(...); Fixing this issue by: 1. Restoring the previous behavior of apic_clear_irr: clear irr_pending, call apic_clear_vector, and then if APIC_IRR is non-zero, set irr_pending. 2. On apic_set_irr: first call apic_set_vector, then set irr_pending. Signed-off-by:
Nadav Amit <namit@cs.technion.ac.il> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Hans de Goede authored
commit 078fd7d6 upstream. Our detection logic to avoid doing UAS on ASM1051 bridge chips causes problems with newer ASM1153 disk enclosures in 2 ways: 1) Some ASM1153 disk enclosures re-use the ASM1051 device-id of 5106, which we assume is always an ASM1051, so remove the quirk for 5106, and instead use the same detection logic as we already use for device-id 55aa, which is used for all of ASM1051, ASM1053 and ASM1153 devices <sigh>. 2) Our detection logic to differentiate between ASM1051 and ASM1053 sees ASM1153 devices as ASM1051 because they have 32 streams like ASM1051 devs. Luckily the ASM1153 descriptors are not 100% identical, unlike the previous models the ASM1153 has bMaxPower == 0, so use that to differentiate it. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Arun Chandran authored
commit 1915e2ad upstream. Building a kernel with CPU_BIG_ENDIAN fails if there are stale objects from a !CPU_BIG_ENDIAN build. Due to a missing FORCE prerequisite on an if_changed rule in the VDSO Makefile, we attempt to link a stale LE object into the new BE kernel. According to Documentation/kbuild/makefiles.txt, FORCE is required for if_changed rules and forgetting it is a common mistake, so fix it by 'Forcing' the build of vdso. This patch fixes build errors like these: arch/arm64/kernel/vdso/note.o: compiled for a little endian system and target is big endian failed to merge target specific data of file arch/arm64/kernel/vdso/note.o arch/arm64/kernel/vdso/sigreturn.o: compiled for a little endian system and target is big endian failed to merge target specific data of file arch/arm64/kernel/vdso/sigreturn.o Tested-by:
Mark Rutland <mark.rutland@arm.com> Signed-off-by:
Arun Chandran <achandran@mvista.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Ian Abbott authored
commit f20fbaad upstream. `spidev_message()` sums the lengths of the individual SPI transfers to determine the overall SPI message length. It restricts the total length, returning an error if too long, but it does not check for arithmetic overflow. For example, if the SPI message consisted of two transfers and the first has a length of 10 and the second has a length of (__u32)(-1), the total length would be seen as 9, even though the second transfer is actually very long. If the second transfer specifies a null `rx_buf` and a non-null `tx_buf`, the `copy_from_user()` could overrun the spidev's pre-allocated tx buffer before it reaches an invalid user memory address. Fix it by checking that neither the total nor the individual transfer lengths exceed the maximum allowed value. Thanks to Dan Carpenter for reporting the potential integer overflow. Signed-off-by:
Ian Abbott <abbotti@mev.co.uk> Signed-off-by:
Mark Brown <broonie@kernel.org> [ luis: backported to 3.16: used backport provided by Ian ] Signed-off-by:
-
Peter Hurley authored
commit fb5ef9e7 upstream. In canon mode, the read buffer head will advance over the buffer tail if the input > 4095 bytes without receiving a line termination char. Discard additional input until a line termination is received. Before evaluating for overflow, the 'room' value is normalized for I_PARMRK and 1 byte is reserved for line termination (even in !icanon mode, in case the mode is switched). The following table shows the transform: actual buffer | 'room' value before overflow calc space avail | !I_PARMRK | I_PARMRK -------------------------------------------------- 0 | -1 | -1 1 | 0 | 0 2 | 1 | 0 3 | 2 | 0 4+ | 3 | 1 When !icanon or when icanon and the read buffer contains newlines, normalized 'room' values of -1 and 0 are clamped to 0, and 'overflow' is 0, so read_head is not adjusted and the input i/o loop exits (setting no_room if called from flush_to_ldisc()). No input is discarded since the reader does have input available to read which ensures forward progress. When icanon and the read buffer does not contain newlines and the normalized 'room' value is 0, then overflow and room are reset to 1, so that the i/o loop will process the next input char normally (except for parity errors which are ignored). Thus, erasures, signalling chars, 7-bit mode, etc. will continue to be handled properly. If the input char processed was not a line termination char, then the canon_head index will not have advanced, so the normalized 'room' value will now be -1 and 'overflow' will be set, which indicates the read_head can safely be reset, effectively erasing the last char processed. If the input char processed was a line termination, then the canon_head index will have advanced, so 'overflow' is cleared to 0, the read_head is not reset, and 'room' is cleared to 0, which exits the i/o loop (because the reader now have input available to read which ensures forward progress). Note that it is possible for a line termination to be received, and for the reader to copy the line to the user buffer before the input i/o loop is ready to process the next input char. This is why the i/o loop recomputes the room/overflow state with every input char while handling overflow. Finally, if the input data was processed without receiving a line termination (so that overflow is still set), the pty driver must receive a write wakeup. A pty writer may be waiting to write more data in n_tty_write() but without unthrottling here that wakeup will not arrive, and forward progress will halt. (Normally, the pty writer is woken when the reader reads data out of the buffer and more space become available). Signed-off-by:
Peter Hurley <peter@hurleysoftware.com> Signed-off-by:
Joseph Salisbury <joseph.salisbury@canonical.com> Signed-off-by:
-
Luis Henriques authored
Signed-off-by:
-
- 21 Apr, 2015 3 commits
-
-
Ben Hutchings authored
Commit 355a901e ("tcp: make connect() mem charging friendly") changed tcp_send_syn_data() to perform an open-coded copy of the 'syn' skb rather than using skb_copy_expand(). The open-coded copy does not cover the skb_shared_info::gso_segs field, so in the new skb it is left set to 0. When this commit was backported into stable branches between 3.10.y and 3.16.7-ckty inclusive, it triggered the BUG() in tcp_transmit_skb(). Since Linux 3.18 the GSO segment count is kept in the tcp_skb_cb::tcp_gso_segs field and tcp_send_syn_data() does copy the tcp_skb_cb structure to the new skb, so mainline and newer stable branches are not affected. Set skb_shared_info::gso_segs to the correct value of 1. Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Acked-by:
-
Andrew Elble authored
commit c1b8940b upstream. We have observed a BUG() crash in fs/attr.c:notify_change(). The crash occurs during an rsync into a filesystem that is exported via NFS. 1.) fs/attr.c:notify_change() modifies the caller's version of attr. 2.) 6de0ec00 ("VFS: make notify_change pass ATTR_KILL_S*ID to setattr operations") introduced a BUG() restriction such that "no function will ever call notify_change() with both ATTR_MODE and ATTR_KILL_S*ID set". Under some circumstances though, it will have assisted in setting the caller's version of attr to this very combination. 3.) 27ac0ffe ("locks: break delegations on any attribute modification") introduced code to handle breaking delegations. This can result in notify_change() being re-called. attr _must_ be explicitly reset to avoid triggering the BUG() established in #2. 4.) The path that that triggers this is via fs/open.c:chmod_common(). The combination of attr flags set here and in the first call to notify_change() along with a later failed break_deleg_wait() results in notify_change() being called again via retry_deleg without resetting attr. Solution is to move retry_deleg in chmod_common() a bit further up to ensure attr is completely reset. There are other places where this seemingly could occur, such as fs/utimes.c:utimes_common(), but the attr flags are not initially set in such a way to trigger this. Fixes: 27ac0ffe ("locks: break delegations on any attribute modification") Reported-by:
Eric Meddaugh <etmsys@rit.edu> Tested-by:
Andrew Elble <aweits@rit.edu> Signed-off-by:
-
Seth Jennings authored
commit 351fc4a9 upstream. Intel IA32 SDM Table 15-14 defines channel 0xf as 'not specified', but EDAC doesn't know about this and returns and INTERNAL ERROR when the channel is greater than NUM_CHANNELS: kernel: [ 1538.886456] CPU 0: Machine Check Exception: 0 Bank 1: 940000000000009f kernel: [ 1538.886669] TSC 2bc68b22e7e812 ADDR 46dae7000 MISC 0 PROCESSOR 0:306e4 TIME 1390414572 SOCKET 0 APIC 0 kernel: [ 1538.971948] EDAC MC1: INTERNAL ERROR: channel value is out of range (15 >= 4) kernel: [ 1538.972203] EDAC MC1: 0 CE memory read error on unknown memory (slot:0 page:0x46dae7 offset:0x0 grain:0 syndrome:0x0 - area:DRAM err_code:0000:009f socket:1 channel_mask:1 rank:0) This commit changes sb_edac to forward a channel of -1 to EDAC if the channel is not specified. edac_mc_handle_error() sets the channel to -1 internally after the error message anyway, so this commit should have no effect other than avoiding the INTERNAL ERROR message when the channel is not specified. Signed-off-by:
Seth Jennings <sjenning@redhat.com> Signed-off-by:
-
