There are typos in setting RTL8168H hardware parameters. If system install
another version driver that may cuase system hang.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dmitry reported memory leaks of IP options allocated in
ip_cmsg_send() when/if this function returns an error.

Callers are responsible for the freeing.

Many thanks to Dmitry for the report and diagnostic.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The return value of kzalloc on failure of allocation of memory should
be -ENOMEM and not -1.

Found using Coccinelle. A simplified version of the semantic patch
used is:

//<smpl>
@@
expression *e;
position p,q;
@@

e@q = kzalloc(...);
if@p (e == NULL) {
...
return
- -1
+ -ENOMEM
;
}
//</smpl>

This function may also return -1 after calling mpp2_prs_tcam_port_map_get.
So that the function consistently returns meaningful error values on
failure, the -1 is changed to -EINVAL.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The return value of vmalloc on failure of allocation of memory should
be -ENOMEM and not -1.

Found using Coccinelle. A simplified version of the semantic patch
used is:

//<smpl>
@@
expression *e;
identifier l1;
position p,q;
@@

e@q = vmalloc(...);
if@p (e == NULL) {
...
goto l1;
}
l1:
...
return -1
+ -ENOMEM
;
//</smpl

The single call site of the containing function checks whether the
returned value is -1, so this check is changed as well. The single call
site of this call site, however, only checks whether the value is not 0,
so no further change was required.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current logic in bond_arp_rcv will accept an incoming ARP for
validation if (a) the receiving slave is either "active" (which includes
the currently active slave, or the current ARP slave) or, (b) there is a
currently active slave, and it has received an ARP since it became active.
For case (b), the receiving slave isn't the currently active slave, and is
receiving the original broadcast ARP request, not an ARP reply from the
target.

	This logic can fail if there is no currently active slave.  In
this situation, the ARP probe logic cycles through all slaves, assigning
each in turn as the "current_arp_slave" for one arp_interval, then setting
that one as "active," and sending an ARP probe from that slave.  The
current logic expects the ARP reply to arrive on the sending
current_arp_slave, however, due to switch FDB updating delays, the reply
may be directed to another slave.

	This can arise if the bonding slaves and switch are working, but
the ARP target is not responding.  When the ARP target recovers, a
condition may result wherein the ARP target host replies faster than the
switch can update its forwarding table, causing each ARP reply to be sent
to the previous current_arp_slave.  This will never pass the logic in
bond_arp_rcv, as neither of the above conditions (a) or (b) are met.

	Some experimentation on a LAN shows ARP reply round trips in the
200 usec range, but my available switches never update their FDB in less
than 4000 usec.

	This patch changes the logic in bond_arp_rcv to additionally
accept an ARP reply for validation on any slave if there is a current ARP
slave and it sent an ARP probe during the previous arp_interval.

Fixes: aeea64ac ("bonding: don't trust arp requests unless active slave really works")
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull GPIO fixes from Linus Walleij:
 - Probe errorpath fix for the Altera
 - irqchip ofnode pointer added to the DaVinci driver
 - controller instance number correction for DaVinci

* tag 'gpio-v4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: davinci: Fix the number of controllers allocated
  gpio: davinci: Add the missing of-node pointer
  gpio: gpio-altera: Remove gpiochip on probe failure.

Merge tag 'platform-drivers-x86-v4.5-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86

Pull x86 platform driver fixes from Darren Hart:
 "Just two small fixes for the 4.5-rc cycle:

  intel_scu_ipcutil:
   - underflow in scu_reg_access()

  intel-hid:
   - fix incorrect entries in intel_hid_keymap"

* tag 'platform-drivers-x86-v4.5-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
  intel_scu_ipcutil: underflow in scu_reg_access()
  intel-hid: fix incorrect entries in intel_hid_keymap

Pull networking fixes from David Miller:

 1) Fix BPF handling of branch offset adjustmnets on backjumps, from
    Daniel Borkmann.

 2) Make sure selinux knows about SOCK_DESTROY netlink messages, from
    Lorenzo Colitti.

 3) Fix openvswitch tunnel mtu regression, from David Wragg.

 4) Fix ICMP handling of TCP sockets in syn_recv state, from Eric
    Dumazet.

 5) Fix SCTP user hmacid byte ordering bug, from Xin Long.

 6) Fix recursive locking in ipv6 addrconf, from Subash Abhinov
    Kasiviswanathan.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  bpf: fix branch offset adjustment on backjumps after patching ctx expansion
  vxlan, gre, geneve: Set a large MTU on ovs-created tunnel devices
  geneve: Relax MTU constraints
  vxlan: Relax MTU constraints
  flow_dissector: Fix unaligned access in __skb_flow_dissector when used by eth_get_headlen
  of: of_mdio: Add marvell, 88e1145 to whitelist of PHY compatibilities.
  selinux: nlmsgtab: add SOCK_DESTROY to the netlink mapping tables
  sctp: translate network order to host order when users get a hmacid
  enic: increment devcmd2 result ring in case of timeout
  tg3: Fix for tg3 transmit queue 0 timed out when too many gso_segs
  net:Add sysctl_max_skb_frags
  tcp: do not drop syn_recv on all icmp reports
  ipv6: fix a lockdep splat
  unix: correctly track in-flight fds in sending process user_struct
  update be2net maintainers' email addresses
  dwc_eth_qos: Reset hardware before PHY start
  ipv6: addrconf: Fix recursive spin lock call

Pull rdma fixes from Doug Ledford:
 "A few more minor fixes for rc3:

   - One fix to ipoib
   - One fix to core sysfs code
   - Four patches that resolve an oops found in testing of ocrdma and a
     couple other ocrdma issues"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
  RDMA/ocrdma: Fixing ocrdma debugfs directory remove
  RDMA/ocrdma: Fix pkey_index returned by driver in rq work completion
  RDMA/ocrdma: populate max_sge_rd in device attributes
  RDMA/ocrdma: Initialize stats resources in the driver before ib device registration.
  IB/sysfs: remove unused va_list args
  IB/IPoIB: Do not set skb truesize since using one linearskb

When ctx access is used, the kernel often needs to expand/rewrite
instructions, so after that patching, branch offsets have to be
adjusted for both forward and backward jumps in the new eBPF program,
but for backward jumps it fails to account the delta. Meaning, for
example, if the expansion happens exactly on the insn that sits at
the jump target, it doesn't fix up the back jump offset.

Analysis on what the check in adjust_branches() is currently doing:

  /* adjust offset of jmps if necessary */
  if (i < pos && i + insn->off + 1 > pos)
    insn->off += delta;
  else if (i > pos && i + insn->off + 1 < pos)
    insn->off -= delta;

First condition (forward jumps):

  Before:                         After:

  insns[0]                        insns[0]
  insns[1] <--- i/insn            insns[1] <--- i/insn
  insns[2] <--- pos               insns[P] <--- pos
  insns[3]                        insns[P]  `------| delta
  insns[4] <--- target_X          insns[P]   `-----|
  insns[5]                        insns[3]
                                  insns[4] <--- target_X
                                  insns[5]

First case is if we cross pos-boundary and the jump instruction was
before pos. This is handeled correctly. I.e. if i == pos, then this
would mean our jump that we currently check was the patchlet itself
that we just injected. Since such patchlets are self-contained and
have no awareness of any insns before or after the patched one, the
delta is correctly not adjusted. Also, for the second condition in
case of i + insn->off + 1 == pos, means we jump to that newly patched
instruction, so no offset adjustment are needed. That part is correct.

Second condition (backward jumps):

  Before:                         After:

  insns[0]                        insns[0]
  insns[1] <--- target_X          insns[1] <--- target_X
  insns[2] <--- pos <-- target_Y  insns[P] <--- pos <-- target_Y
  insns[3]                        insns[P]  `------| delta
  insns[4] <--- i/insn            insns[P]   `-----|
  insns[5]                        insns[3]
                                  insns[4] <--- i/insn
                                  insns[5]

Second interesting case is where we cross pos-boundary and the jump
instruction was after pos. Backward jump with i == pos would be
impossible and pose a bug somewhere in the patchlet, so the first
condition checking i > pos is okay only by itself. However, i +
insn->off + 1 < pos does not always work as intended to trigger the
adjustment. It works when jump targets would be far off where the
delta wouldn't matter. But, for example, where the fixed insn->off
before pointed to pos (target_Y), it now points to pos + delta, so
that additional room needs to be taken into account for the check.
This means that i) both tests here need to be adjusted into pos + delta,
and ii) for the second condition, the test needs to be <= as pos
itself can be a target in the backjump, too.

Fixes: 9bac3d6d ("bpf: allow extended BPF programs access skb fields")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull input updates from Dmitry Torokhov:
 "Just small driver fixups"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: colibri-vf50-ts - add missing #include <linux/of.h>
  Input: adp5589 - fix row 5 handling for adp5589
  Input: edt-ft5x06 - fix setting gain, offset, and threshold via device tree
  Input: vmmouse - fix absolute device registration
  Input: serio - drop warnings in case of EPROBE_DEFER from serio_find_driver()
  Input: cap11xx - add missing of_node_put
  Input: sirfsoc-onkey - allow modular build
  Input: xpad - remove unused function

Pull libata fixes from Tejun Heo:

 - PORTS_IMPL workaround for very early ahci controllers is misbehaving
   on new systems.  Disabled on recent ahci versions.

 - Old-style PIO state machine had a horrible locking problem.  Don't
   know how we've been getting away this far.  Fixed.

 - Other device specific updates.

* 'for-4.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  ahci: Intel DNV device IDs SATA
  libata: fix sff host state machine locking while polling
  libata-sff: use WARN instead of BUG on illegal host state machine state
  libata: disable forced PORTS_IMPL for >= AHCI 1.3
  libata: blacklist a Viking flash model for MWDMA corruption
  drivers: ata: wake port before DMA stop for ALPM

Pull cgroup fixes from Tejun Heo:

 - The destruction path of cgroup objects are asynchronous and
   multi-staged and some of them ended up destroying parents before
   children leading to failures in cpu and memory controllers.  Ensure
   that parents are always destroyed after children.

 - cpuset mm node migration was performed synchronously while holding
   threadgroup and cgroup mutexes and the recent threadgroup locking
   update resulted in a possible deadlock.  The migration is best effort
   and shouldn't have been performed under those locks to begin with.
   Made asynchronous.

 - Minor documentation fix.

* 'for-4.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  Documentation: cgroup: Fix 'cgroup-legacy' -> 'cgroup-v1'
  cgroup: make sure a parent css isn't freed before its children
  cgroup: make sure a parent css isn't offlined before its children
  cpuset: make mm migration asynchronous

Pull workqueue fixes from Tejun Heo:
 "Workqueue fixes for v4.5-rc3.

   - Remove a spurious triggering of flush dependency warning.

   - Officially break local execution guarantee of unbound work items
     and add a debug feature to flush out usages which depend on it.

   - Work around CPU -> NODE mapping becoming invalid on CPU offline.

  The branch is young but pushing out early as stable kernels are being
  affected"

* 'for-4.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  workqueue: handle NUMA_NO_NODE for unbound pool_workqueue lookup
  workqueue: implement "workqueue.debug_force_rr_cpu" debug feature
  workqueue: schedule WORK_CPU_UNBOUND work on wq_unbound_cpumask CPUs
  Revert "workqueue: make sure delayed work run in local cpu"
  workqueue: skip flush dependency checks for legacy workqueues

When looking up the pool_workqueue to use for an unbound workqueue,
workqueue assumes that the target CPU is always bound to a valid NUMA
node.  However, currently, when a CPU goes offline, the mapping is
destroyed and cpu_to_node() returns NUMA_NO_NODE.

This has always been broken but hasn't triggered often enough before
874bbfe6 ("workqueue: make sure delayed work run in local cpu").
After the commit, workqueue forcifully assigns the local CPU for
delayed work items without explicit target CPU to fix a different
issue.  This widens the window where CPU can go offline while a
delayed work item is pending causing delayed work items dispatched
with target CPU set to an already offlined CPU.  The resulting
NUMA_NO_NODE mapping makes workqueue try to queue the work item on a
NULL pool_workqueue and thus crash.

While 874bbfe6 has been reverted for a different reason making the
bug less visible again, it can still happen.  Fix it by mapping
NUMA_NO_NODE to the default pool_workqueue from unbound_pwq_by_node().
This is a temporary workaround.  The long term solution is keeping CPU
-> NODE mapping stable across CPU off/online cycles which is being
worked on.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: Len Brown <len.brown@intel.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/g/1454424264.11183.46.camel@gmail.com
Link: http://lkml.kernel.org/g/1453702100-2597-1-git-send-email-tangchen@cn.fujitsu.com

Adding Intel codename DNV platform device IDs for SATA.
Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org

David Wragg says:

====================
Set a large MTU on ovs-created tunnel devices

Prior to 4.3, openvswitch tunnel vports (vxlan, gre and geneve) could
transmit vxlan packets of any size, constrained only by the ability to
send out the resulting packets.  4.3 introduced netdevs corresponding
to tunnel vports.  These netdevs have an MTU, which limits the size of
a packet that can be successfully encapsulated.  The default MTU
values are low (1500 or less), which is awkwardly small in the context
of physical networks supporting jumbo frames, and leads to a
conspicuous change in behaviour for userspace.

This patch series sets the MTU on openvswitch-created netdevs to be
the relevant maximum (i.e. the maximum IP packet size minus any
relevant overhead), effectively restoring the behaviour prior to 4.3.

Where relevant, the limits on MTU values that can be directly set on
the netdevs are also relaxed.

Changes in v2:
* Extend to all openvswitch tunnel types, i.e. gre and geneve as well
* Use IP_MAX_MTU

Changes in v3:
* Fix block comment style
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Prior to 4.3, openvswitch tunnel vports (vxlan, gre and geneve) could
transmit vxlan packets of any size, constrained only by the ability to
send out the resulting packets.  4.3 introduced netdevs corresponding
to tunnel vports.  These netdevs have an MTU, which limits the size of
a packet that can be successfully encapsulated.  The default MTU
values are low (1500 or less), which is awkwardly small in the context
of physical networks supporting jumbo frames, and leads to a
conspicuous change in behaviour for userspace.

Instead, set the MTU on openvswitch-created netdevs to be the relevant
maximum (i.e. the maximum IP packet size minus any relevant overhead),
effectively restoring the behaviour prior to 4.3.
Signed-off-by: David Wragg <david@weave.works>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow the MTU of geneve devices to be set to large values, in order to
exploit underlying networks with larger frame sizes.

GENEVE does not have a fixed encapsulation overhead (an openvswitch
rule can add variable length options), so there is no relevant maximum
MTU to enforce.  A maximum of IP_MAX_MTU is used instead.
Encapsulated packets that are too big for the underlying network will
get dropped on the floor.
Signed-off-by: David Wragg <david@weave.works>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow the MTU of vxlan devices without an underlying device to be set
to larger values (up to a maximum based on IP packet limits and vxlan
overhead).

Previously, their MTUs could not be set to higher than the
conventional ethernet value of 1500.  This is a very arbitrary value
in the context of vxlan, and prevented vxlan devices from being able
to take advantage of jumbo frames etc.

The default MTU remains 1500, for compatibility.
Signed-off-by: David Wragg <david@weave.works>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver only needs to allocate for [ngpio / 32] controllers,
as each controller handles 32 gpios. But the current driver
allocates for ngpio of which the extra allocated are unused.
Fix it be registering only the required number of controllers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Currently the first parameter of irq_domain_add_legacy is NULL.
irq_find_host function returns NULL when we do not populate the of_node
and hence irq_of_parse_and_map call fails whenever we want to request a
gpio irq. This fixes the request_irq failures for gpio interrupts.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Pull module fixes from Rusty Russell:
 "Fix for async_probe module param added in 4.3 (clearly not widely used
  yet), and a much more interesting kallsyms race which has been around
  approximately forever.  This fix is more invasive, and will require
  some care in backporting, but I hated all the bandaids I could think
  of, so...

  There are some more coming, which are only for breakages introduced
  this cycle (livepatch), but wanted these in now"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
  modules: fix longstanding /proc/kallsyms vs module insertion race.
  module: wrapper for symbol name.
  modules: fix modparam async_probe request

drivers/input/touchscreen/colibri-vf50-ts.c: In function ‘vf50_ts_probe’:
drivers/input/touchscreen/colibri-vf50-ts.c:302: error: implicit declaration of function ‘of_property_read_u32’
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The adp5589 has row 5, don't skip it when creating the GPIO mapping.
Otherwise the pin gets reserved as used and it is not possible to use it as
a GPIO.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

A recent patch broke parsing the gain, offset, and threshold parameters
from device tree. Instead of setting the cached values and writing them
to the correct registers during probe, it would write the values from DT
into the register address variables and never write them to the chip
during normal operation.

Fixes: 2e23b7a9 ("Input: edt-ft5x06 - use generic properties API")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Workqueue used to guarantee local execution for work items queued
without explicit target CPU.  The guarantee is gone now which can
break some usages in subtle ways.  To flush out those cases, this
patch implements a debug feature which forces round-robin CPU
selection for all such work items.

The debug feature defaults to off and can be enabled with a kernel
parameter.  The default can be flipped with a debug config option.

If you hit this commit during bisection, please refer to 041bd12e
("Revert "workqueue: make sure delayed work run in local cpu"") for
more information and ping me.
Signed-off-by: Tejun Heo <tj@kernel.org>

WORK_CPU_UNBOUND work items queued to a bound workqueue always run
locally.  This is a good thing normally, but not when the user has
asked us to keep unbound work away from certain CPUs.  Round robin
these to wq_unbound_cpumask CPUs instead, as perturbation avoidance
trumps performance.

tj: Cosmetic and comment changes.  WARN_ON_ONCE() dropped from empty
    (wq_unbound_cpumask AND cpu_online_mask).  If we want that, it
    should be done when config changes.
Signed-off-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>

This reverts commit 874bbfe6.

Workqueue used to implicity guarantee that work items queued without
explicit CPU specified are put on the local CPU.  Recent changes in
timer broke the guarantee and led to vmstat breakage which was fixed
by 176bed1d ("vmstat: explicitly schedule per-cpu work on the CPU
we need it to run on").

vmstat is the most likely to expose the issue and it's quite possible
that there are other similar problems which are a lot more difficult
to trigger.  As a preventive measure, 874bbfe6 ("workqueue: make
sure delayed work run in local cpu") was applied to restore the local
CPU guarnatee.  Unfortunately, the change exposed a bug in timer code
which got fixed by 22b886dd ("timers: Use proper base migration in
add_timer_on()").  Due to code restructuring, the commit couldn't be
backported beyond certain point and stable kernels which only had
874bbfe6 started crashing.

The local CPU guarantee was accidental more than anything else and we
want to get rid of it anyway.  As, with the vmstat case fixed,
874bbfe6 is causing more problems than it's fixing, it has been
decided to take the chance and officially break the guarantee by
reverting the commit.  A debug feature will be added to force foreign
CPU assignment to expose cases relying on the guarantee and fixes for
the individual cases will be backported to stable as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: 874bbfe6 ("workqueue: make sure delayed work run in local cpu")
Link: http://lkml.kernel.org/g/20160120211926.GJ10810@quack.suse.cz
Cc: stable@vger.kernel.org
Cc: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Daniel Bilik <daniel.bilik@neosystem.cz>
Cc: Jan Kara <jack@suse.cz>
Cc: Shaohua Li <shli@fb.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Bilik <daniel.bilik@neosystem.cz>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Michal Hocko <mhocko@kernel.org>

Pull crypto fixes from Herbert Xu:
 "This fixes the following issues:

  API:
   - Fix async algif_skcipher, it was broken by recent fixes.
   - Fix potential race condition in algif_skcipher with ctx.
   - Fix potential memory corruption in algif_skcipher.
   - Add missing lock to crypto_user when doing an alg dump.

  Drivers:
   - marvell/cesa was testing the wrong variable for NULL after
     allocation.
   - Fix potential double-free in atmel-sha.
   - Fix illegal call to sleepin function from atomic context in
     atmel-sha"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: marvell/cesa - fix test in mv_cesa_dev_dma_init()
  crypto: atmel-sha - remove calls of clk_prepare() from atomic contexts
  crypto: atmel-sha - fix atmel_sha_remove()
  crypto: algif_skcipher - Do not set MAY_BACKLOG on the async path
  crypto: algif_skcipher - Do not dereference ctx without socket lock
  crypto: algif_skcipher - Do not assume that req is unchanged
  crypto: user - lock crypto_alg_list on alg dump

Long ago, Dave Jones complained about CONFIG_LOCALVERSION_AUTO:
 "I don't use the auto config, because I end up filling up /boot unless
  I go through and clean them out by hand every time I install a new one
  (which I do probably a dozen or so times a day).  Is there some easy
  way to prune old builds I'm missing?"

To which Bruce replied:
 "I run this by hand every now and then.  I'm probably doing it all wrong"

And if he is running it wrong, then so am I - because I've been using
this script ever since.  It is true that CONFIG_LOCALVERSION_AUTO easily
ends up filling your /boot partition if you don't clean up old versions
regularly, and this script helps make that easier.

Checked with Bruce to see that it's fine to add this to the kernel
scripts.  Maybe people will come up with enhancements, but more
importantly, this way I won't misplace this script whenever I install a
new machine and start doing custom kernels for it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch fixes an issue with unaligned accesses when using
eth_get_headlen on a page that was DMA aligned instead of being IP aligned.
The fact is when trying to check the length we don't need to be looking at
the flow label so we can reorder the checks to first check if we are
supposed to gather the flow label and then make the call to actually get
it.

v2:  Updated path so that either STOP_AT_FLOW_LABEL or KEY_FLOW_LABEL can
     cause us to check for the flow label.
Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit ae461131 ("of: of_mdio: Add a whitelist of PHY
compatibilities.") missed one compatible string used in in-tree DTBs:
in OCTEON, for selected boards, the kernel DTB pruning code will overwrite
the DTB compatible string with "marvell,88e1145", which is missing
from the whitelist. Add it.

The patch fixes broken networking on EdgeRouter Lite.

Fixes: ae461131 ("of: of_mdio: Add a whitelist of PHY compatibilities.")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Without this, using SOCK_DESTROY in enforcing mode results in:

  SELinux: unrecognized netlink message type=21 for sclass=32
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit ed5a377d ("sctp: translate host order to network order when
setting a hmacid") corrected the hmacid byte-order when setting a hmacid.
but the same issue also exists on getting a hmacid.

We fix it by changing hmacids to host order when users get them with
getsockopt.

Fixes: Commit ed5a377d ("sctp: translate host order to network order when setting a hmacid")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Firmware posts the devcmd result in result ring. In case of timeout, driver
does not increment the current result pointer and firmware could post the
result after timeout has occurred. During next devcmd, driver would be
reading the result of previous devcmd.

Fix this by incrementing result even in case of timeout.

Fixes: 373fb087 ("enic: add devcmd2")
Signed-off-by: Sandeep Pillai <sanpilla@cisco.com>
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3_tso_bug() can hit a condition where the entire tx ring is not big
enough to segment the GSO packet. For example, if MSS is very small,
gso_segs can exceed the tx ring size. When we hit the condition, it
will cause tx timeout.

tg3_tso_bug() is called to handle TSO and DMA hardware bugs.
For TSO bugs, if tg3_tso_bug() cannot succeed, we have to drop the packet.
For DMA bugs, we can still fall back to linearize the SKB and let the
hardware transmit the TSO packet.

This patch adds a function tg3_tso_bug_gso_check() to check if there
are enough tx descriptors for GSO before calling tg3_tso_bug().
The caller will then handle the error appropriately - drop or
lineraize the SKB.

v2: Corrected patch description to avoid confusion.
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Devices may have limits on the number of fragments in an skb they support.
Current codebase uses a constant as maximum for number of fragments one
skb can hold and use.
When enabling scatter/gather and running traffic with many small messages
the codebase uses the maximum number of fragments and may thereby violate
the max for certain devices.
The patch introduces a global variable as max number of fragments.
Signed-off-by: Hans Westgaard Ry <hans.westgaard.ry@oracle.com>
Reviewed-by: Håkon Bugge <haakon.bugge@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Petr Novopashenniy reported that ICMP redirects on SYN_RECV sockets
were leading to RST.

This is of course incorrect.

A specific list of ICMP messages should be able to drop a SYN_RECV.

For instance, a REDIRECT on SYN_RECV shall be ignored, as we do
not hold a dst per SYN_RECV pseudo request.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=111751
Fixes: 079096f1 ("tcp/dccp: install syn_recv requests into ehash table")
Reported-by: Petr Novopashenniy <pety@rusnet.ru>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull KVM fixes from Paolo Bonzini:
 "KVM-ARM fixes, mostly coming from the PMU work"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  arm64: KVM: Fix guest dead loop when register accessor returns false
  arm64: KVM: Fix comments of the CP handler
  arm64: KVM: Fix wrong use of the CPSR MODE mask for 32bit guests
  arm64: KVM: Obey RES0/1 reserved bits when setting CPTR_EL2
  arm64: KVM: Fix AArch64 guest userspace exception injection