- 14 Nov, 2014 21 commits
-
-
Hans de Goede authored
commit 2391eacb upstream. Streams seem to be broken on the Asmedia 1042. An uas capable Seagate disk which is known to work fine with other controllers causes the system to freeze when connected over usb-3 with this controller, where as it works fine with uas in usb-2 ports, indicating a problem with streams. This is a bit bigger hammer then I would like to use for this, but for now it will have to make do. I've ordered a pci-e usb controller card with an Asmedia 1042, once that arrives I'll try to get streams to work (with a quirk flag if necessary) and then we can re-enable them. For now this at least makes uas capable disk enclosures work again by forcing fallback to the usb-storage driver. Reported-by:
Bogdan Mihalcea <bogdan.mihalcea@infim.ro> Cc: Bogdan Mihalcea <bogdan.mihalcea@infim.ro> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Hans de Goede authored
commit aee0ce3a upstream. These drives hang when receiving ATA12 commands, so set the US_FL_NO_ATA_1X quirk to filter these out. Signed-off-by:
-
Alan Stern authored
commit 93c9bf4d upstream. Sometimes mass-storage devices using the Bulk-only transport will mistakenly skip the data phase of a command. Rather than sending the data expected by the host or sending a zero-length packet, they go directly to the status phase and send the CSW. This causes problems for usb-storage, for obvious reasons. The driver will interpret the CSW as a short data transfer and will wait to receive a CSW. The device won't have anything left to send, so the command eventually times out. The SCSI layer doesn't retry commands after they time out (this is a relatively recent change). Therefore we should do our best to detect a skipped data phase and handle it promptly. This patch adds code to do that. If usb-storage receives a short 13-byte data transfer from the device, and if the first four bytes of the data match the CSW signature, the driver will set the residue to the full transfer length and interpret the data as a CSW. This fixes Bugzilla #86611. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Tested-by:
Paul Osmialowski <newchief@king.net.pl> Signed-off-by:
-
Hans de Goede authored
commit 90a646c7 upstream. This commit fixes the following oops: [10238.622067] scsi host3: uas_eh_bus_reset_handler start [10240.766164] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd [10245.779365] usb 3-4: device descriptor read/8, error -110 [10245.883331] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd [10250.897603] usb 3-4: device descriptor read/8, error -110 [10251.058200] BUG: unable to handle kernel NULL pointer dereference at 0000000000000040 [10251.058244] IP: [<ffffffff815ac6e1>] xhci_check_streams_endpoint+0x91/0x140 <snip> [10251.059473] Call Trace: [10251.059487] [<ffffffff815aca6c>] xhci_calculate_streams_and_bitmask+0xbc/0x130 [10251.059520] [<ffffffff815aeb5f>] xhci_alloc_streams+0x10f/0x5a0 [10251.059548] [<ffffffff810a4685>] ? check_preempt_curr+0x75/0xa0 [10251.059575] [<ffffffff810a46dc>] ? ttwu_do_wakeup+0x2c/0x100 [10251.059601] [<ffffffff810a49e6>] ? ttwu_do_activate.constprop.111+0x66/0x70 [10251.059635] [<ffffffff815779ab>] usb_alloc_streams+0xab/0xf0 [10251.059662] [<ffffffffc0616b48>] uas_configure_endpoints+0x128/0x150 [uas] [10251.059694] [<ffffffffc0616bac>] uas_post_reset+0x3c/0xb0 [uas] [10251.059722] [<ffffffff815727d9>] usb_reset_device+0x1b9/0x2a0 [10251.059749] [<ffffffffc0616f42>] uas_eh_bus_reset_handler+0xb2/0x190 [uas] [10251.059781] [<ffffffff81514293>] scsi_try_bus_reset+0x53/0x110 [10251.059808] [<ffffffff815163b7>] scsi_eh_bus_reset+0xf7/0x270 <snip> The problem is the following call sequence (simplified): 1) usb_reset_device 2) usb_reset_and_verify_device 2) hub_port_init 3) hub_port_finish_reset 3) xhci_discover_or_reset_device This frees xhci->devs[slot_id]->eps[ep_index].ring for all eps but 0 4) usb_get_device_descriptor This fails 5) hub_port_init fails 6) usb_reset_and_verify_device fails, does not restore device config 7) uas_post_reset 8) xhci_alloc_streams NULL deref on the free-ed ring This commit fixes this by not allowing usb_alloc_streams to continue if the device is not configured. Note that we do allow usb_free_streams to continue after a (logical) disconnect, as it is necessary to explicitly free the streams at the xhci controller level. Signed-off-by:
-
Johan Hovold authored
commit cf84a691 upstream. Add device-id entry for GW Instek AFG-2225, which has a byte swapped bInterfaceSubClass (0x20). Reported-by:
Karl Palsson <karlp@tweak.net.au> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Krzysztof Kozlowski authored
commit ca0c37a0 upstream. Driver allocated on stack struct regulator_config but didn't initialize it fully. Few fields (driver_data, ena_gpio) were left untouched. This lead to using random ena_gpio values as GPIOs for max77693 regulators. On occasion these values could match real GPIO numbers leading to interfering with other drivers and to unsuccessful enable/disable of regulator. Signed-off-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Fixes: 80b022e2 ("regulator: max77693: Add max77693 regualtor driver.") Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Johan Hovold authored
commit e681286d upstream. Write may be called from interrupt context so make sure to use GFP_ATOMIC for all allocations in write. Fixes: 0d930e51 ("USB: opticon: Add Opticon OPN2001 write support") Signed-off-by:
-
Johan Hovold authored
commit 19125283 upstream. Write may be called from interrupt context so make sure to use GFP_ATOMIC for all allocations in write. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Grzegorz Jaszczyk authored
commit 758e8366 upstream. In both Armada-375 and Armada-38x MPIC interrupts should be identified by reading cause register multiplied by the interrupt mask. A lack of above mentioned multiplication resulted in a bug, caused by the fact that in Armada-375 and Armada-38x some of the interrupts (e.g. network interrupts) can be handled either as a GIC or MPIC interrupts. Therefore during MPIC interrupts handling, cause register shows hits from interrupts even if they are masked for MPIC but unmasked for a GIC. This resulted in 'bad IRQ' error, because masked MPIC interrupt without registered interrupt handler, was trying to be handled during interrupt handling procedure of some other unmasked MPIC interrupt (e.g. local timer irq). This commit fixes that by ensuring that during MPIC interrupt handling only interrupts that are unmasked for MPIC are processed. Signed-off-by:
Grzegorz Jaszczyk <jaz@semihalf.com> Reviewed-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Fixes: bc69b8ad ("irqchip: armada-370-xp: Setup a chained handler for the MPIC") Acked-by:
Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Link: https://lkml.kernel.org/r/1411643839-64925-3-git-send-email-jaz@semihalf.comSigned-off-by:
Jason Cooper <jason@lakedaemon.net> Signed-off-by:
-
Grzegorz Jaszczyk authored
commit 298dcb2d upstream. The MSI interrupts use the 16 high doorbells, which are notified by using IRQ1 of the main interrupt controller. The MSI interrupts were handled correctly for Armada-XP and Armada-370 but not for Armada-375 and Armada-38x, which use chained handler for the MPIC. This commit fixes that by checking proper interrupt number in chained handler for the MPIC. Signed-off-by:
-
Benjamin Herrenschmidt authored
commit 325e4114 upstream. Endian is hard, especially when I designed a stupid FW interface, and I should know better... oh well, this is attempt #2 at fixing this properly. This time it seems to work with all access sizes and I can run my flashing tool (which exercises all sort of access sizes and types to access the SPI controller in the BMC) just fine. Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Anton Blanchard authored
commit 808be314 upstream. Back in 7230c564 ("powerpc: Rework lazy-interrupt handling") we added a call out to restore_interrupts() (written in c) before calling do_notify_resume: bl restore_interrupts addi r3,r1,STACK_FRAME_OVERHEAD bl do_notify_resume Unfortunately do_notify_resume takes two arguments, the second one being the thread_info flags: void do_notify_resume(struct pt_regs *regs, unsigned long thread_info_flags) We do populate r4 (the second argument) earlier, but restore_interrupts() is free to muck it up all it wants. My guess is the gcc compiler gods shone down on us and its register allocator never used r4. Sometimes, rarely, luck is on our side. LLVM on the other hand did trample r4. Signed-off-by:
Anton Blanchard <anton@samba.org> Signed-off-by:
-
Ulrich Eckhardt authored
commit 8c5bcded upstream. The Tevii S480 outputs 18V on startup for the LNB supply voltage and does not automatically power down. This blocks other receivers connected to a satellite channel router (EN50494), since the receivers can not send the required DiSEqC sequences when the Tevii card is connected to a the same SCR. This patch switches off the LNB supply voltage on initialization of the frontend. [mchehab@osg.samsung.com: add a comment about why we're explicitly turning off voltage at device init] Signed-off-by:
Ulrich Eckhardt <uli@uli-eckhardt.de> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
-
Jan Kara authored
commit a8d42056 upstream. When we fail to allocate page vector in rbd_obj_read_sync() we just basically ignore the problem and continue which will result in an oops later. Fix the problem by returning proper error. CC: Yehuda Sadeh <yehuda@inktank.com> CC: Sage Weil <sage@inktank.com> CC: ceph-devel@vger.kernel.org Coverity-id: 1226882 Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
Ilya Dryomov <idryomov@redhat.com> Signed-off-by:
-
Lukas Bossard authored
commit 7c21539c upstream. Adding ultra doch support for Lenovo Thinkpad X240 (17aa:2214). [Actually replaced the entry with ALC292_FIXUP_TPT440_DOCK -- tiwai] Signed-off-by:
Lukas Bossard <mr.bobukas@gmail.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit 6d16941a upstream. There is another Thinkpad T440 with SSID 17aa:2212 that has a dock port. Reported-by:
Siwei Luo <sluo@smartbeans.de> Signed-off-by:
-
David Cohen authored
commit d90c3381 upstream. Even if a gpio pin is set to output, we still need to set INPUT_EN functionality (by clearing INPUT_EN bit) to be able to read the pin's level. E.g. without this change, we'll always read low level state from sysfs. Cc: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
David Cohen <david.a.cohen@linux.intel.com> Reviewed-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
-
Hans de Goede authored
commit 183fd8fc upstream. The acpi-video backlight interface on the Acer KAV80 is broken, and worse it causes the entire machine to slow down significantly after a suspend/resume. Blacklist it, and use the acer-wmi backlight interface instead. Note that the KAV80 is somewhat unique in that it is the only Acer model where we fall back to acer-wmi after blacklisting, rather then using the native (e.g. intel) backlight driver. This is done because there is no native backlight interface on this model. BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1128309Signed-off-by:
Darren Hart <dvhart@linux.intel.com> Signed-off-by:
-
Hans de Goede authored
commit 5a1426c9 upstream. The acpi-video backlight interface on the NC210 does not work, blacklist it and use the samsung-laptop interface instead. BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=861573Signed-off-by:
-
Luis Henriques authored
Signed-off-by: -
Cong Wang authored
commit 21e81002 upstream. I saw the following kernel warning: [ 1852.321222] ------------[ cut here ]------------ [ 1852.326527] WARNING: CPU: 0 PID: 118 at fs/proc/generic.c:521 remove_proc_entry+0x154/0x16b() [ 1852.335630] remove_proc_entry: removing non-empty directory 'fs/nfsfs', leaking at least 'volumes' [ 1852.344084] CPU: 0 PID: 118 Comm: kworker/u8:2 Not tainted 3.16.0+ #540 [ 1852.350036] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 [ 1852.354992] Workqueue: netns cleanup_net [ 1852.358701] 0000000000000000 ffff880116f2fbd0 ffffffff819c03e9 ffff880116f2fc18 [ 1852.366474] ffff880116f2fc08 ffffffff810744ee ffffffff811e0e6e ffff8800d4e96238 [ 1852.373507] ffffffff81dbe665 ffff8800d46a5948 0000000000000005 ffff880116f2fc68 [ 1852.380224] Call Trace: [ 1852.381976] [<ffffffff819c03e9>] dump_stack+0x4d/0x66 [ 1852.385495] [<ffffffff810744ee>] warn_slowpath_common+0x7a/0x93 [ 1852.389869] [<ffffffff811e0e6e>] ? remove_proc_entry+0x154/0x16b [ 1852.393987] [<ffffffff8107457b>] warn_slowpath_fmt+0x4c/0x4e [ 1852.397999] [<ffffffff811e0e6e>] remove_proc_entry+0x154/0x16b [ 1852.402034] [<ffffffff8129c73d>] nfs_fs_proc_net_exit+0x53/0x56 [ 1852.406136] [<ffffffff812a103b>] nfs_net_exit+0x12/0x1d [ 1852.409774] [<ffffffff81785bc9>] ops_exit_list+0x44/0x55 [ 1852.413529] [<ffffffff81786389>] cleanup_net+0xee/0x182 [ 1852.417198] [<ffffffff81088c9e>] process_one_work+0x209/0x40d [ 1852.502320] [<ffffffff81088bf7>] ? process_one_work+0x162/0x40d [ 1852.587629] [<ffffffff810890c1>] worker_thread+0x1f0/0x2c7 [ 1852.673291] [<ffffffff81088ed1>] ? process_scheduled_works+0x2f/0x2f [ 1852.759470] [<ffffffff8108e079>] kthread+0xc9/0xd1 [ 1852.843099] [<ffffffff8109427f>] ? finish_task_switch+0x3a/0xce [ 1852.926518] [<ffffffff8108dfb0>] ? __kthread_parkme+0x61/0x61 [ 1853.008565] [<ffffffff819cbeac>] ret_from_fork+0x7c/0xb0 [ 1853.076477] [<ffffffff8108dfb0>] ? __kthread_parkme+0x61/0x61 [ 1853.140653] ---[ end trace 69c4c6617f78e32d ]--- It looks wrong that we add "/proc/net/nfsfs" in nfs_fs_proc_net_init() while remove "/proc/fs/nfsfs" in nfs_fs_proc_net_exit(). Fixes: commit 65b38851 (NFS: Fix /proc/fs/nfsfs/servers and /proc/fs/nfsfs/volumes) Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Trond Myklebust <trond.myklebust@primarydata.com> Cc: Dan Aloni <dan@kernelim.com> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> [Trond: replace uses of remove_proc_entry() with remove_proc_subtree() as suggested by Al Viro] Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by:
-
- 13 Nov, 2014 19 commits
-
-
Jan Kara authored
commit f55fefd1 upstream. The WARN_ON checking whether i_mutex is held in pagecache_isize_extended() was wrong because some filesystems (e.g. XFS) use different locks for serialization of truncates / writes. So just remove the check. Signed-off-by:
Dave Chinner <dchinner@redhat.com> Signed-off-by:
Dave Chinner <david@fromorbit.com> Signed-off-by:
-
Eric W. Biederman authored
commit 0d082601 upstream. Andy Lutomirski recently demonstrated that when chroot is used to set the root path below the path for the new ``root'' passed to pivot_root the pivot_root system call succeeds and leaks mounts. In examining the code I see that starting with a new root that is below the current root in the mount tree will result in a loop in the mount tree after the mounts are detached and then reattached to one another. Resulting in all kinds of ugliness including a leak of that mounts involved in the leak of the mount loop. Prevent this problem by ensuring that the new mount is reachable from the current root of the mount tree. [Added stable cc. Fixes CVE-2014-7970. --Andy] Reported-by:
Andy Lutomirski <luto@amacapital.net> Reviewed-by:
"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
-
Andy Lutomirski authored
commit 653bc77a upstream. Rusty noticed a Really Bad Bug (tm) in my NT fix. The entry code reads out of bounds, causing the NT fix to be unreliable. But, and this is much, much worse, if your stack is somehow just below the top of the direct map (or a hole), you read out of bounds and crash. Excerpt from the crash: [ 1.129513] RSP: 0018:ffff88001da4bf88 EFLAGS: 00010296 2b:* f7 84 24 90 00 00 00 testl $0x4000,0x90(%rsp) That read is deterministically above the top of the stack. I thought I even single-stepped through this code when I wrote it to check the offset, but I clearly screwed it up. Fixes: 8c7aa698 ("x86_64, entry: Filter RFLAGS.NT on entry from userspace") Reported-by:
Rusty Russell <rusty@ozlabs.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Andy Lutomirski authored
commit 8c7aa698 upstream. The NT flag doesn't do anything in long mode other than causing IRET to #GP. Oddly, CPL3 code can still set NT using popf. Entry via hardware or software interrupt clears NT automatically, so the only relevant entries are fast syscalls. If user code causes kernel code to run with NT set, then there's at least some (small) chance that it could cause trouble. For example, user code could cause a call to EFI code with NT set, and who knows what would happen? Apparently some games on Wine sometimes do this (!), and, if an IRET return happens, they will segfault. That segfault cannot be handled, because signal delivery fails, too. This patch programs the CPU to clear NT on entry via SYSCALL (both 32-bit and 64-bit, by my reading of the AMD APM), and it clears NT in software on entry via SYSENTER. To save a few cycles, this borrows a trick from Jan Beulich in Xen: it checks whether NT is set before trying to clear it. As a result, it seems to have very little effect on SYSENTER performance on my machine. There's another minor bug fix in here: it looks like the CFI annotations were wrong if CONFIG_AUDITSYSCALL=n. Testers beware: on Xen, SYSENTER with NT set turns into a GPF. I haven't touched anything on 32-bit kernels. The syscall mask change comes from a variant of this patch by Anish Bhatt. Note to stable maintainers: there is no known security issue here. A misguided program can set NT and cause the kernel to try and fail to deliver SIGSEGV, crashing the program. This patch fixes Far Cry on Wine: https://bugs.winehq.org/show_bug.cgi?id=33275Reported-by:
Anish Bhatt <anish@chelsio.com> Signed-off-by:
H. Peter Anvin <hpa@zytor.com> Signed-off-by:
-
Rabin Vincent authored
commit 086ba77a upstream. ARM has some private syscalls (for example, set_tls(2)) which lie outside the range of NR_syscalls. If any of these are called while syscall tracing is being performed, out-of-bounds array access will occur in the ftrace and perf sys_{enter,exit} handlers. # trace-cmd record -e raw_syscalls:* true && trace-cmd report ... true-653 [000] 384.675777: sys_enter: NR 192 (0, 1000, 3, 4000022, ffffffff, 0) true-653 [000] 384.675812: sys_exit: NR 192 = 1995915264 true-653 [000] 384.675971: sys_enter: NR 983045 (76f74480, 76f74000, 76f74b28, 76f74480, 76f76f74, 1) true-653 [000] 384.675988: sys_exit: NR 983045 = 0 ... # trace-cmd record -e syscalls:* true [ 17.289329] Unable to handle kernel paging request at virtual address aaaaaace [ 17.289590] pgd = 9e71c000 [ 17.289696] [aaaaaace] *pgd=00000000 [ 17.289985] Internal error: Oops: 5 [#1] PREEMPT SMP ARM [ 17.290169] Modules linked in: [ 17.290391] CPU: 0 PID: 704 Comm: true Not tainted 3.18.0-rc2+ #21 [ 17.290585] task: 9f4dab00 ti: 9e710000 task.ti: 9e710000 [ 17.290747] PC is at ftrace_syscall_enter+0x48/0x1f8 [ 17.290866] LR is at syscall_trace_enter+0x124/0x184 Fix this by ignoring out-of-NR_syscalls-bounds syscall numbers. Commit cd0980fc "tracing: Check invalid syscall nr while tracing syscalls" added the check for less than zero, but it should have also checked for greater than NR_syscalls. Link: http://lkml.kernel.org/p/1414620418-29472-1-git-send-email-rabin@rab.in Fixes: cd0980fc "tracing: Check invalid syscall nr while tracing syscalls" Signed-off-by:
Rabin Vincent <rabin@rab.in> Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Eric Rannaud authored
commit 69a91c23 upstream. The man page for open(2) indicates that when O_CREAT is specified, the 'mode' argument applies only to future accesses to the file: Note that this mode applies only to future accesses of the newly created file; the open() call that creates a read-only file may well return a read/write file descriptor. The man page for open(2) implies that 'mode' is treated identically by O_CREAT and O_TMPFILE. O_TMPFILE, however, behaves differently: int fd = open("/tmp", O_TMPFILE | O_RDWR, 0); assert(fd == -1); assert(errno == EACCES); int fd = open("/tmp", O_TMPFILE | O_RDWR, 0600); assert(fd > 0); For O_CREAT, do_last() sets acc_mode to MAY_OPEN only: if (*opened & FILE_CREATED) { /* Don't check for write permission, don't truncate */ open_flag &= ~O_TRUNC; will_truncate = false; acc_mode = MAY_OPEN; path_to_nameidata(path, nd); goto finish_open_created; } But for O_TMPFILE, do_tmpfile() passes the full op->acc_mode to may_open(). This patch lines up the behavior of O_TMPFILE with O_CREAT. After the inode is created, may_open() is called with acc_mode = MAY_OPEN, in do_tmpfile(). A different, but related glibc bug revealed the discrepancy: https://sourceware.org/bugzilla/show_bug.cgi?id=17523 The glibc lazily loads the 'mode' argument of open() and openat() using va_arg() only if O_CREAT is present in 'flags' (to support both the 2 argument and the 3 argument forms of open; same idea for openat()). However, the glibc ignores the 'mode' argument if O_TMPFILE is in 'flags'. On x86_64, for open(), it magically works anyway, as 'mode' is in RDX when entering open(), and is still in RDX on SYSCALL, which is where the kernel looks for the 3rd argument of a syscall. But openat() is not quite so lucky: 'mode' is in RCX when entering the glibc wrapper for openat(), while the kernel looks for the 4th argument of a syscall in R10. Indeed, the syscall calling convention differs from the regular calling convention in this respect on x86_64. So the kernel sees mode = 0 when trying to use glibc openat() with O_TMPFILE, and fails with EACCES. Signed-off-by:
Eric Rannaud <e@nanocritical.com> Acked-by:
-
Cyril Brulebois authored
commit 664d6a79 upstream. 0x1b75 0xa200 AirLive WN-200USB wireless 11b/g/n dongle References: https://bugs.debian.org/766802Reported-by:
Martin Mokrejs <mmokrejs@fold.natur.cuni.cz> Signed-off-by:
Cyril Brulebois <kibi@debian.org> Acked-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Greg Kroah-Hartman authored
commit d8e7d53a upstream. Back in commit 5136b2da ("PCI: convert bus code to use dev_groups"), I misstyped the 'enable' sysfs filename as 'enabled', which broke the userspace API. This patch fixes that issue by renaming the file back. Fixes: 5136b2da ("PCI: convert bus code to use dev_groups") Reported-by:
Jeff Epler <jepler@unpythonic.net> Tested-by: Jeff Epler <jepler@unpythonic.net> # on v3.14-rt Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Signed-off-by:
-
Jan Kara authored
commit 6050d47a upstream. When ext4_handle_dirty_dx_node() or ext4_handle_dirty_dirent_node() fail, there's really something wrong with the fs and there's no point in continuing further. Just return error from make_indexed_dir() in that case. Also initialize frames array so that if we return early due to error, dx_release() doesn't try to dereference uninitialized memory (which could happen also due to error in do_split()). Coverity-id: 741300 Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Theodore Ts'o authored
commit f8b3b59d upstream. Signed-off-by:
-
Dmitry Monakhov authored
commit a41537e6 upstream. O_DIRECT flags can be toggeled via fcntl(F_SETFL). But this value checked twice inside ext4_file_write_iter() and __generic_file_write() which result in BUG_ON inside ext4_direct_IO. Let's initialize iocb->private unconditionally. TESTCASE: xfstest:generic/036 https://patchwork.ozlabs.org/patch/402445/ #TYPICAL STACK TRACE: kernel BUG at fs/ext4/inode.c:2960! invalid opcode: 0000 [#1] SMP Modules linked in: brd iTCO_wdt lpc_ich mfd_core igb ptp dm_mirror dm_region_hash dm_log dm_mod CPU: 6 PID: 5505 Comm: aio-dio-fcntl-r Not tainted 3.17.0-rc2-00176-gff5c017 #161 Hardware name: Intel Corporation W2600CR/W2600CR, BIOS SE5C600.86B.99.99.x028.061320111235 06/13/2011 task: ffff88080e95a7c0 ti: ffff88080f908000 task.ti: ffff88080f908000 RIP: 0010:[<ffffffff811fabf2>] [<ffffffff811fabf2>] ext4_direct_IO+0x162/0x3d0 RSP: 0018:ffff88080f90bb58 EFLAGS: 00010246 RAX: 0000000000000400 RBX: ffff88080fdb2a28 RCX: 00000000a802c818 RDX: 0000040000080000 RSI: ffff88080d8aeb80 RDI: 0000000000000001 RBP: ffff88080f90bbc8 R08: 0000000000000000 R09: 0000000000001581 R10: 0000000000000000 R11: 0000000000000000 R12: ffff88080d8aeb80 R13: ffff88080f90bbf8 R14: ffff88080fdb28c8 R15: ffff88080fdb2a28 FS: 00007f23b2055700(0000) GS:ffff880818400000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f23b2045000 CR3: 000000080cedf000 CR4: 00000000000407e0 Stack: ffff88080f90bb98 0000000000000000 7ffffffffffffffe ffff88080fdb2c30 0000000000000200 0000000000000200 0000000000000001 0000000000000200 ffff88080f90bbc8 ffff88080fdb2c30 ffff88080f90be08 0000000000000200 Call Trace: [<ffffffff8112ca9d>] generic_file_direct_write+0xed/0x180 [<ffffffff8112f2b2>] __generic_file_write_iter+0x222/0x370 [<ffffffff811f495b>] ext4_file_write_iter+0x34b/0x400 [<ffffffff811bd709>] ? aio_run_iocb+0x239/0x410 [<ffffffff811bd709>] ? aio_run_iocb+0x239/0x410 [<ffffffff810990e5>] ? local_clock+0x25/0x30 [<ffffffff810abd94>] ? __lock_acquire+0x274/0x700 [<ffffffff811f4610>] ? ext4_unwritten_wait+0xb0/0xb0 [<ffffffff811bd756>] aio_run_iocb+0x286/0x410 [<ffffffff810990e5>] ? local_clock+0x25/0x30 [<ffffffff810ac359>] ? lock_release_holdtime+0x29/0x190 [<ffffffff811bc05b>] ? lookup_ioctx+0x4b/0xf0 [<ffffffff811bde3b>] do_io_submit+0x55b/0x740 [<ffffffff811bdcaa>] ? do_io_submit+0x3ca/0x740 [<ffffffff811be030>] SyS_io_submit+0x10/0x20 [<ffffffff815ce192>] system_call_fastpath+0x16/0x1b Code: 01 48 8b 80 f0 01 00 00 48 8b 18 49 8b 45 10 0f 85 f1 01 00 00 48 03 45 c8 48 3b 43 48 0f 8f e3 01 00 00 49 83 7c 24 18 00 75 04 <0f> 0b eb fe f0 ff 83 ec 01 00 00 49 8b 44 24 18 8b 00 85 c0 89 RIP [<ffffffff811fabf2>] ext4_direct_IO+0x162/0x3d0 RSP <ffff88080f90bb58> Reported-by:
Sasha Levin <sasha.levin@oracle.com> Signed-off-by:
Dmitry Monakhov <dmonakhov@openvz.org> Signed-off-by:
-
Darrick J. Wong authored
commit 98c1a759 upstream. If metadata checksumming is turned on for the FS, we need to tell the journal to use checksumming too. Signed-off-by:
Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by:
-
Jan Kara authored
commit 599a9b77 upstream. When we fail to load block bitmap in __ext4_new_inode() we will dereference NULL pointer in ext4_journal_get_write_access(). So check for error from ext4_read_block_bitmap(). Coverity-id: 989065 Signed-off-by:
-
Jan Kara authored
commit 9378c676 upstream. When there are no meta block groups update_backups() will compute the backup block in 32-bit arithmetics thus possibly overflowing the block number and corrupting the filesystem. OTOH filesystems without meta block groups larger than 16 TB should be rare. Fix the problem by doing the counting in 64-bit arithmetics. Coverity-id: 741252 Signed-off-by:
Lukas Czerner <lczerner@redhat.com> Signed-off-by:
-
Dmitry Eremin-Solenikov authored
commit 89cf38dd upstream. After '#echo mem > /sys/power/state' some devices can not be properly resumed because apparently the MTD Partition Configuration Register has been reset to default thus the rootfs cannot be mounted cleanly on resume. An example of this can be found in the SA-1100 Developer's Manual at 9.5.3.3 where the second step of the Sleep Shutdown Sequence is described: "An internal reset is applied to the SA-1100. All units are reset...". As workaround we refresh the PCR value as done initially on chip setup. This behavior and the fix are confirmed by our tests done on 2 different Zaurus collie units with kernel 3.17. Fixes: 812c5fa8: ("mtd: cfi_cmdset_0001.c: add support for Sharp LH28F640BF NOR") Signed-off-by:
Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Signed-off-by:
Andrea Adami <andrea.adami@gmail.com> Signed-off-by:
Brian Norris <computersforpeace@gmail.com> Signed-off-by:
-
Andriy Skulysh authored
commit 5417421b upstream. Resources scif1_resources & scif2_resources overlap. Actual SCIF region size is 0x10. This is regression from commit d850acf9 ("sh: Declare SCIF register base and IRQ as resources") Signed-off-by:
Andriy Skulysh <askulysh@gmail.com> Acked-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Jan Kara authored
commit ea5d05b3 upstream. If __bitmap_shift_left() or __bitmap_shift_right() are asked to shift by a multiple of BITS_PER_LONG, they will try to shift a long value by BITS_PER_LONG bits which is undefined. Change the functions to avoid the undefined shift. Coverity id: 1192175 Coverity id: 1192174 Signed-off-by:
-
David Rientjes authored
commit 6d50e60c upstream. If an anonymous mapping is not allowed to fault thp memory and then madvise(MADV_HUGEPAGE) is used after fault, khugepaged will never collapse this memory into thp memory. This occurs because the madvise(2) handler for thp, hugepage_madvise(), clears VM_NOHUGEPAGE on the stack and it isn't stored in vma->vm_flags until the final action of madvise_behavior(). This causes the khugepaged_enter_vma_merge() to be a no-op in hugepage_madvise() when the vma had previously had VM_NOHUGEPAGE set. Fix this by passing the correct vma flags to the khugepaged mm slot handler. There's no chance khugepaged can run on this vma until after madvise_behavior() returns since we hold mm->mmap_sem. It would be possible to clear VM_NOHUGEPAGE directly from vma->vm_flags in hugepage_advise(), but I didn't want to introduce special case behavior into madvise_behavior(). I think it's best to just let it always set vma->vm_flags itself. Signed-off-by:
David Rientjes <rientjes@google.com> Reported-by:
Suleiman Souhlal <suleiman@google.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by:
-
Yu Zhao authored
commit 5ddacbe9 upstream. Compound page should be freed by put_page() or free_pages() with correct order. Not doing so will cause tail pages leaked. The compound order can be obtained by compound_order() or use HPAGE_PMD_ORDER in our case. Some people would argue the latter is faster but I prefer the former which is more general. This bug was observed not just on our servers (the worst case we saw is 11G leaked on a 48G machine) but also on our workstations running Ubuntu based distro. $ cat /proc/vmstat | grep thp_zero_page_alloc thp_zero_page_alloc 55 thp_zero_page_alloc_failed 0 This means there is (thp_zero_page_alloc - 1) * (2M - 4K) memory leaked. Fixes: 97ae1749 ("thp: implement refcounting for huge zero page") Signed-off-by:
Yu Zhao <yuzhao@google.com> Acked-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Mel Gorman <mel@csn.ul.ie> Cc: David Rientjes <rientjes@google.com> Cc: Bob Liu <lliubbo@gmail.com> Signed-off-by:
-
