The assignment 'cf->data[2] |= CAN_ERR_PROT_UNSPEC' used at CAN error message
creation time is obsolete as CAN_ERR_PROT_UNSPEC is zero and cf->data[2] is
initialized with zero in alloc_can_err_skb() anyway.

So we could either assign 'cf->data[2] = CAN_ERR_PROT_UNSPEC' correctly or we
can remove the obsolete OR operation entirely.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

As Dan Carpenter reported in http://marc.info/?l=linux-can&m=144793696016187
the assignment of the error location in CAN error messages had some bit wise
overlaps. Indeed the value to be assigned in data[3] is no bitfield but defines
a single value which points to a location inside the CAN frame on the wire.

This patch fixes the assignments for the error locations in error messages.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

According to SJA1000 data sheet error-warning (EI) interrupt is not
cleared by setting the controller in to reset-mode.

Then if we have the following case:
- system is suspended (echo mem > /sys/power/state) and SJA1000 is left
  in operating state
- A bus error condition occurs which activates EI interrupt, system is
  still suspended which means EI interrupt will be not be handled nor
  cleared.

If the above two events occur, on resume there is no way to return the
SJA1000 to operating state, except to cycle power to it.

By simply reading the IR register on start we will clear any previous
conditions that could be present.
Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com>
Reported-by: Christian Magnusson <Christian.Magnusson@semcon.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Similar to ipv4, when destroying an mrt table the static mfc entries and
the static devices are kept, which leads to devices that can never be
destroyed (because of refcnt taken) and leaked memory. Make sure that
everything is cleaned up on netns destruction.

Fixes: 8229efda ("netns: ip6mr: enable namespace support in ipv6 multicast forwarding code")
CC: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When destroying an mrt table the static mfc entries and the static
devices are kept, which leads to devices that can never be destroyed
(because of refcnt taken) and leaked memory, for example:
unreferenced object 0xffff880034c144c0 (size 192):
  comm "mfc-broken", pid 4777, jiffies 4320349055 (age 46001.964s)
  hex dump (first 32 bytes):
    98 53 f0 34 00 88 ff ff 98 53 f0 34 00 88 ff ff  .S.4.....S.4....
    ef 0a 0a 14 01 02 03 04 00 00 00 00 01 00 00 00  ................
  backtrace:
    [<ffffffff815c1b9e>] kmemleak_alloc+0x4e/0xb0
    [<ffffffff811ea6e0>] kmem_cache_alloc+0x190/0x300
    [<ffffffff815931cb>] ip_mroute_setsockopt+0x5cb/0x910
    [<ffffffff8153d575>] do_ip_setsockopt.isra.11+0x105/0xff0
    [<ffffffff8153e490>] ip_setsockopt+0x30/0xa0
    [<ffffffff81564e13>] raw_setsockopt+0x33/0x90
    [<ffffffff814d1e14>] sock_common_setsockopt+0x14/0x20
    [<ffffffff814d0b51>] SyS_setsockopt+0x71/0xc0
    [<ffffffff815cdbf6>] entry_SYSCALL_64_fastpath+0x16/0x7a
    [<ffffffffffffffff>] 0xffffffffffffffff

Make sure that everything is cleaned on netns destruction.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2015-11-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
iwlwifi

* bump API to firmware 19 - not released yet.
* fix D3 flows (Luca)
* new device IDs (Oren)
* fix NULL pointer dereference (Avri)

ath10k

* fix invalid NSS for 4x4 devices
* add QCA9377 hw1.0 support
* fix QCA6174 regression with CE5 usage

wil6210

* new maintainer - Maya Erez

rtlwifi

* rtl8821ae: Fix lockups on boot
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

I haven't had any PCI tulip HW for the past ~5 years. I have
been reviewing tulip patches and can continue doing that.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

David and HacKurx reported a following/similar size overflow triggered
in a grsecurity kernel, thanks to PaX's gcc size overflow plugin:

(Already fixed in later grsecurity versions by Brad and PaX Team.)

[ 1002.296137] PAX: size overflow detected in function scm_detach_fds net/core/scm.c:314
               cicus.202_127 min, count: 4, decl: msg_controllen; num: 0; context: msghdr;
[ 1002.296145] CPU: 0 PID: 3685 Comm: scm_rights_recv Not tainted 4.2.3-grsec+ #7
[ 1002.296149] Hardware name: Apple Inc. MacBookAir5,1/Mac-66F35F19FE2A0D05, [...]
[ 1002.296153]  ffffffff81c27366 0000000000000000 ffffffff81c27375 ffffc90007843aa8
[ 1002.296162]  ffffffff818129ba 0000000000000000 ffffffff81c27366 ffffc90007843ad8
[ 1002.296169]  ffffffff8121f838 fffffffffffffffc fffffffffffffffc ffffc90007843e60
[ 1002.296176] Call Trace:
[ 1002.296190]  [<ffffffff818129ba>] dump_stack+0x45/0x57
[ 1002.296200]  [<ffffffff8121f838>] report_size_overflow+0x38/0x60
[ 1002.296209]  [<ffffffff816a979e>] scm_detach_fds+0x2ce/0x300
[ 1002.296220]  [<ffffffff81791899>] unix_stream_read_generic+0x609/0x930
[ 1002.296228]  [<ffffffff81791c9f>] unix_stream_recvmsg+0x4f/0x60
[ 1002.296236]  [<ffffffff8178dc00>] ? unix_set_peek_off+0x50/0x50
[ 1002.296243]  [<ffffffff8168fac7>] sock_recvmsg+0x47/0x60
[ 1002.296248]  [<ffffffff81691522>] ___sys_recvmsg+0xe2/0x1e0
[ 1002.296257]  [<ffffffff81693496>] __sys_recvmsg+0x46/0x80
[ 1002.296263]  [<ffffffff816934fc>] SyS_recvmsg+0x2c/0x40
[ 1002.296271]  [<ffffffff8181a3ab>] entry_SYSCALL_64_fastpath+0x12/0x85

Further investigation showed that this can happen when an *odd* number of
fds are being passed over AF_UNIX sockets.

In these cases CMSG_LEN(i * sizeof(int)) and CMSG_SPACE(i * sizeof(int)),
where i is the number of successfully passed fds, differ by 4 bytes due
to the extra CMSG_ALIGN() padding in CMSG_SPACE() to an 8 byte boundary
on 64 bit. The padding is used to align subsequent cmsg headers in the
control buffer.

When the control buffer passed in from the receiver side *lacks* these 4
bytes (e.g. due to buggy/wrong API usage), then msg->msg_controllen will
overflow in scm_detach_fds():

  int cmlen = CMSG_LEN(i * sizeof(int));  <--- cmlen w/o tail-padding
  err = put_user(SOL_SOCKET, &cm->cmsg_level);
  if (!err)
    err = put_user(SCM_RIGHTS, &cm->cmsg_type);
  if (!err)
    err = put_user(cmlen, &cm->cmsg_len);
  if (!err) {
    cmlen = CMSG_SPACE(i * sizeof(int));  <--- cmlen w/ 4 byte extra tail-padding
    msg->msg_control += cmlen;
    msg->msg_controllen -= cmlen;         <--- iff no tail-padding space here ...
  }                                            ... wrap-around

F.e. it will wrap to a length of 18446744073709551612 bytes in case the
receiver passed in msg->msg_controllen of 20 bytes, and the sender
properly transferred 1 fd to the receiver, so that its CMSG_LEN results
in 20 bytes and CMSG_SPACE in 24 bytes.

In case of MSG_CMSG_COMPAT (scm_detach_fds_compat()), I haven't seen an
issue in my tests as alignment seems always on 4 byte boundary. Same
should be in case of native 32 bit, where we end up with 4 byte boundaries
as well.

In practice, passing msg->msg_controllen of 20 to recvmsg() while receiving
a single fd would mean that on successful return, msg->msg_controllen is
being set by the kernel to 24 bytes instead, thus more than the input
buffer advertised. It could f.e. become an issue if such application later
on zeroes or copies the control buffer based on the returned msg->msg_controllen
elsewhere.

Maximum number of fds we can send is a hard upper limit SCM_MAX_FD (253).

Going over the code, it seems like msg->msg_controllen is not being read
after scm_detach_fds() in scm_recv() anymore by the kernel, good!

Relevant recvmsg() handler are unix_dgram_recvmsg() (unix_seqpacket_recvmsg())
and unix_stream_recvmsg(). Both return back to their recvmsg() caller,
and ___sys_recvmsg() places the updated length, that is, new msg_control -
old msg_control pointer into msg->msg_controllen (hence the 24 bytes seen
in the example).

Long time ago, Wei Yongjun fixed something related in commit 1ac70e7a
("[NET]: Fix function put_cmsg() which may cause usr application memory
overflow").

RFC3542, section 20.2. says:

  The fields shown as "XX" are possible padding, between the cmsghdr
  structure and the data, and between the data and the next cmsghdr
  structure, if required by the implementation. While sending an
  application may or may not include padding at the end of last
  ancillary data in msg_controllen and implementations must accept both
  as valid. On receiving a portable application must provide space for
  padding at the end of the last ancillary data as implementations may
  copy out the padding at the end of the control message buffer and
  include it in the received msg_controllen. When recvmsg() is called
  if msg_controllen is too small for all the ancillary data items
  including any trailing padding after the last item an implementation
  may set MSG_CTRUNC.

Since we didn't place MSG_CTRUNC for already quite a long time, just do
the same as in 1ac70e7a to avoid an overflow.

Btw, even man-page author got this wrong :/ See db939c9b26e9 ("cmsg.3: Fix
error in SCM_RIGHTS code sample"). Some people must have copied this (?),
thus it got triggered in the wild (reported several times during boot by
David and HacKurx).

No Fixes tag this time as pre 2002 (that is, pre history tree).
Reported-by: David Sterba <dave@jikos.cz>
Reported-by: HacKurx <hackurx@gmail.com>
Cc: PaX Team <pageexec@freemail.hu>
Cc: Emese Revfy <re.emese@gmail.com>
Cc: Brad Spengler <spender@grsecurity.net>
Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: Eric Dumazet <edumazet@google.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 52666986 ("tipc: let broadcast packet
reception use new link receive function") the broadcast send
link state was meant to always be set to LINK_ESTABLISHED, since
we don't need this link to follow the regular link FSM rules. It
was also the intention that this state anyway shouldn't impact
the run-time working state of the link, since the latter in
reality is controlled by the number of registered peers.

We have now discovered that this assumption is not quite correct.
If the broadcast link is reset because of too many retransmissions,
its state will inadvertently go to LINK_RESETTING, and never go
back to LINK_ESTABLISHED, because the LINK_FAILURE event was not
anticipated. This will work well once, but if it happens a second
time, the reset on a link in LINK_RESETTING has has no effect, and
neither the broadcast link nor the unicast links will go down as
they should.

Furthermore, it is confusing that the management tool shows that
this link is in UP state when that obviously isn't the case.

We now ensure that this state strictly follows the true working
state of the link. The state is set to LINK_ESTABLISHED when
the number of peers is non-zero, and to LINK_RESET otherwise.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds a driver for the Aurora VLSI NB8800 Ethernet controller.
It is an almost complete rewrite of a driver originally found in
a Sigma Designs 2.6.22 tree.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The tulip driver causes annoying build-time warnings for allmodconfig
builds for all recent architectures:

dec/tulip/winbond-840.c:910:2: warning: #warning Processor architecture undefined
dec/tulip/tulip_core.c:101:2: warning: #warning Processor architecture undefined!

This is the last remaining warning for arm64, and I'd like to get rid of
it. We don't really know the cache line size, architecturally it would
be at least 16 bytes, but all implementations I found have 64 or 128
bytes. Configuring tulip for 32-byte lines as we do on ARM32 seems to
be the safe but slow default, and nobody who cares about performance these
days would use a tulip chip anyway, so we can just use that.

To save the next person the job of trying to find out what this is for
and picking a default for their architecture just to kill off the warning,
I'm now removing the preprocessor #warning and turning it into a pr_warn
or dev_warn that prints the equivalent information when the driver gets
loaded.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commmit ac7eccd4 "bnx2x: track vxlan port count" contains a bug -
Instead of achieving the required goal, vxlan configuration would not
be removed since we're decrementing the port instead of the counter.

CC: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp_send_rcvq() is used for re-injecting data into tcp receive queue.

Problems :

- No check against size is performed, allowed user to fool kernel in
  attempting very large memory allocations, eventually triggering
  OOM when memory is fragmented.

- In case of fault during the copy we do not return correct errno.

Lets use alloc_skb_with_frags() to cook optimal skbs.

Fixes: 292e8d8c ("tcp: Move rcvq sending to tcp_input.c")
Fixes: c0e88ff0 ("tcp: Repair socket queues")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix incrementing TCPFastOpenActiveFailed snmp stats multiple times
when the handshake experiences multiple SYN timeouts.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some middle-boxes black-hole the data after the Fast Open handshake
(https://www.ietf.org/proceedings/94/slides/slides-94-tcpm-13.pdf).
The exact reason is unknown. The work-around is to disable Fast Open
temporarily after multiple recurring timeouts with few or no data
delivered in the established state.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit b6745f6e ("drivers: net: cpsw: davinci_emac: move reading mac
id to common file") started using of_machine_is_compatible for detecting
type but missed at dm8148 causing Ethernet to stop working.

Let's fix the issue by adding handling for dm814x.

Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Mugunthnan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a passive TCP is created, we eventually call tcp_md5_do_add()
with sk pointing to the child. It is not owner by the user yet (we
will add this socket into listener accept queue a bit later anyway)

But we do own the spinlock, so amend the lockdep annotation to avoid
following splat :

[ 8451.090932] net/ipv4/tcp_ipv4.c:923 suspicious rcu_dereference_protected() usage!
[ 8451.090932]
[ 8451.090932] other info that might help us debug this:
[ 8451.090932]
[ 8451.090934]
[ 8451.090934] rcu_scheduler_active = 1, debug_locks = 1
[ 8451.090936] 3 locks held by socket_sockopt_/214795:
[ 8451.090936]  #0:  (rcu_read_lock){.+.+..}, at: [<ffffffff855c6ac1>] __netif_receive_skb_core+0x151/0xe90
[ 8451.090947]  #1:  (rcu_read_lock){.+.+..}, at: [<ffffffff85618143>] ip_local_deliver_finish+0x43/0x2b0
[ 8451.090952]  #2:  (slock-AF_INET){+.-...}, at: [<ffffffff855acda5>] sk_clone_lock+0x1c5/0x500
[ 8451.090958]
[ 8451.090958] stack backtrace:
[ 8451.090960] CPU: 7 PID: 214795 Comm: socket_sockopt_

[ 8451.091215] Call Trace:
[ 8451.091216]  <IRQ>  [<ffffffff856fb29c>] dump_stack+0x55/0x76
[ 8451.091229]  [<ffffffff85123b5b>] lockdep_rcu_suspicious+0xeb/0x110
[ 8451.091235]  [<ffffffff8564544f>] tcp_md5_do_add+0x1bf/0x1e0
[ 8451.091239]  [<ffffffff85645751>] tcp_v4_syn_recv_sock+0x1f1/0x4c0
[ 8451.091242]  [<ffffffff85642b27>] ? tcp_v4_md5_hash_skb+0x167/0x190
[ 8451.091246]  [<ffffffff85647c78>] tcp_check_req+0x3c8/0x500
[ 8451.091249]  [<ffffffff856451ae>] ? tcp_v4_inbound_md5_hash+0x11e/0x190
[ 8451.091253]  [<ffffffff85647170>] tcp_v4_rcv+0x3c0/0x9f0
[ 8451.091256]  [<ffffffff85618143>] ? ip_local_deliver_finish+0x43/0x2b0
[ 8451.091260]  [<ffffffff856181b6>] ip_local_deliver_finish+0xb6/0x2b0
[ 8451.091263]  [<ffffffff85618143>] ? ip_local_deliver_finish+0x43/0x2b0
[ 8451.091267]  [<ffffffff85618d38>] ip_local_deliver+0x48/0x80
[ 8451.091270]  [<ffffffff85618510>] ip_rcv_finish+0x160/0x700
[ 8451.091273]  [<ffffffff8561900e>] ip_rcv+0x29e/0x3d0
[ 8451.091277]  [<ffffffff855c74b7>] __netif_receive_skb_core+0xb47/0xe90

Fixes: a8afca03 ("tcp: md5: protects md5sig_info with RCU")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Thomas reports
"
4gsystems sells two total different LTE-surfsticks under the same name.
..
The newer version of XS Stick W100 is from "omega"
..
Under windows the driver switches to the same ID, and uses MI03\6 for
network and MI01\6 for modem.
..
echo "1c9e 9b01" > /sys/bus/usb/drivers/qmi_wwan/new_id
echo "1c9e 9b01" > /sys/bus/usb-serial/drivers/option1/new_id

T:  Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=  4 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1c9e ProdID=9b01 Rev=02.32
S:  Manufacturer=USB Modem
S:  Product=USB Modem
S:  SerialNumber=
C:  #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage

Now all important things are there:

wwp0s29f7u2i3 (net), ttyUSB2 (at), cdc-wdm0 (qmi), ttyUSB1 (at)

There is also ttyUSB0, but it is not usable, at least not for at.

The device works well with qmi and ModemManager-NetworkManager.
"
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

During code review, I noticed we were passing a bad buffer pointer
to bpf_load_pointer helper function called by jitted code.

Point to the buffer allocated by JIT, so we don't silently corrupt
other parts of the stack.
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Acked-by: Yang Shi <yang.shi@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the R8A7795 support was  added to the driver, little attention was paid
to the ravb_open() error path: free_irq()  for the EMAC interrupt was called
uncoditionally, unlike request_irq(), and in  a wrong order as well...
As a result, on the R-Car gen2 SoCs I started getting the following in case
of a device  opening error:

WARNING: CPU: 0 PID: 1 at kernel/irq/manage.c:1448 __free_irq+0x8c/0x228()
Trying to free already-free IRQ 0
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.4.0-rc1-dirty #1005
Hardware name: Generic R8A7791 (Flattened Device Tree)
Backtrace:
[<c0013818>] (dump_backtrace) from [<c00139b4>] (show_stack+0x18/0x1c)
 r6:c063cdd6 r5:00000009 r4:00000000 r3:00204140
[<c001399c>] (show_stack) from [<c022a578>] (dump_stack+0x74/0x90)
[<c022a504>] (dump_stack) from [<c0025f04>] (warn_slowpath_common+0x8c/0xb8)
 r4:ef04fd38 r3:c0714770
[<c0025e78>] (warn_slowpath_common) from [<c0025fd4>] (warn_slowpath_fmt+0x38/0x40)
 r8:ee8ad800 r7:ef0030a0 r6:00000000 r5:00000000 r4:ef003040
[<c0025fa0>] (warn_slowpath_fmt) from [<c0064cc0>] (__free_irq+0x8c/0x228)
 r3:00000000 r2:c063ce9f
[<c0064c34>] (__free_irq) from [<c0064ecc>] (free_irq+0x70/0xa4)
 r10:0000016b r8:00000000 r7:00000000 r6:ee8ad800 r5:00000000 r4:ef003040
[<c0064e5c>] (free_irq) from [<c033472c>] (ravb_open+0x224/0x274)
 r7:fffffffe r6:00000000 r5:fffffffe r4:ee8ad800
[<c0334508>] (ravb_open) from [<c041ac78>] (__dev_open+0x84/0x104)
 r7:ee8ad830 r6:c0566334 r5:00000000 r4:ee8ad800
[<c041abf4>] (__dev_open) from [<c041af08>] (__dev_change_flags+0x94/0x13c)
 r7:00001002 r6:00000001 r5:00001003 r4:ee8ad800
[<c041ae74>] (__dev_change_flags) from [<c041afe8>] (dev_change_flags+0x20/0x50)
 r7:c072e6e0 r6:00000138 r5:00001002 r4:ee8ad800
[<c041afc8>] (dev_change_flags) from [<c06ec06c>] (ip_auto_config+0x174/0xfb8)
 r8:00001002 r7:c072e6e0 r6:c0703344 r5:00000001 r4:ee8ad800 r3:00000101
[<c06ebef8>] (ip_auto_config) from [<c000a810>] (do_one_initcall+0x100/0x1cc)
 r10:c06fb83c r9:00000000 r8:c06ebef8 r7:c0736000 r6:c0710918 r5:c0710918
 r4:ef2f8f80
[<c000a710>] (do_one_initcall) from [<c06ccddc>] (kernel_init_freeable+0x11c/0x1
ec)
 r10:c06fb83c r9:00000000 r8:0000009a r7:c0736000 r6:c0706bf0 r5:c06fb834
 r4:00000007
[<c06cccc0>] (kernel_init_freeable) from [<c0514c54>] (kernel_init+0x14/0xec)
 r10:00000000 r8:00000000 r7:00000000 r6:00000000 r5:c0514c40 r4:c0736000
[<c0514c40>] (kernel_init) from [<c0010458>] (ret_from_fork+0x14/0x3c)
 r4:00000000 r3:ef04e000

Fix up the free_irq() call order and add a new label on the error path.

Fixes: 22d4df8f ("ravb: Add support for r8a7795 SoC")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Changes the definition of the pointer _expiry from time_t to
time64_t. This is to handle the Y2038 problem where time_t
will overflow in the year 2038. The change is safe because
the kernel subsystems that call dns_query pass NULL.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Aya Mahfouz <mahfouz.saif.elyazal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

the commit cdf3464e ("ipv6: Fix dst_entry refcnt bugs in ip6_tunnel")
introduced percpu storage for ip6_tunnel dst cache, but while clearing
such cache it used raw_cpu_ptr to walk the per cpu entries, so cached
dst on non current cpu are not actually reset.

This patch replaces raw_cpu_ptr with per_cpu_ptr, properly cleaning
such storage.

Fixes: cdf3464e ("ipv6: Fix dst_entry refcnt bugs in ip6_tunnel")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for the sgmii phy interface.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the PCI device ID (0xe0a1) and alx_pci_tbl entry for the
Killer E2400 Ethernet controller, modeled after the Killer E2200
controller support (0xe091) already present in the alx driver.

This patch was originally authored by Ben Pope, but it got held up by
issues in the commit message, so I'm resubmitting it on his behalf.

I've extensively used a kernel with this patch on a System76 serw9
laptop and am quite confident it works well (at least on the hardware I
have available for testing).

Note that as a favor to System76, Ubuntu has been carrying this as a
sauce patch in their 4.2 based Wily kernel, which presumably has given
it real-world testing on other E2400 equipped hardware (I don't know of
any Ubuntu kernel bugs filed about it):

https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1498633Signed-off-by: Jason Gerard DeRose <jason@system76.com>
Signed-off-by: Ben Pope <benpope81@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If alloc_netdev() failed and return NULL, then the next instruction
would dereference it. Found by Coverity.

Compile tested only. Not sure if anyone still uses this driver
(or the whole WAN subsystem).
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This was detected by Coverity.
The function skb_cow_head leaves skb alone on failure, so caller needs
to free.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull s390 fixes from Martin Schwidefsky:
 "Assorted bug fixes, the mlock2 system call gets added, and one
  improvement.  The boot from dasd devices is now possible from a wider
  range of devices"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390: remove SALIPL loader
  s390: wire up mlock2 system call
  s390: remove g5 elf platform support
  s390: avoid cache aliasing under z/VM and KVM
  s390/sclp: _sclp_wait_int(): retain full PSW mask
  s390/zcrypt: Fix initialisation when zcrypt is built-in
  s390/zcrypt: Fix kernel crash on systems without AP bus support
  s390: add support for ipl devices in subchannel sets > 0
  s390/ipl: fix out of bounds access in scpdata_write
  s390/pci_dma: improve debugging of errors during dma map
  s390/pci_dma: handle dma table failures
  s390/pci_dma: unify label of invalid translation table entries
  s390/syscalls: remove system call number calculation
  s390/cio: simplify css_generate_pgid
  s390/diag: add a s390 prefix to the diagnose trace point
  s390/head: fix error message on unsupported hardware

Merge tag 'hwmon-for-linus-v4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fixes from Guenter Roeck:
 "Fix build issues in scpi and ina2xx drivers, update scpi driver to
  support recent firmware, and fix an uninitialized variable warning in
  applesmc driver"

* tag 'hwmon-for-linus-v4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (scpi) skip unsupported sensors properly
  hwmon: (scpi) add thermal-of dependency
  hwmon : (applesmc) Fix uninitialized variables warnings
  hwmon: (ina2xx) Fix build issue by selecting REGMAP_I2C

Pull networking fixes from David Miller:

 1) Fix list tests in netfilter ingress support, from Florian Westphal.

 2) Fix reversal of input and output interfaces in ingress hook
    invocation, from Pablo Neira Ayuso.

 3) We have a use after free in r8169, caught by Dave Jones, fixed by
    Francois Romieu.

 4) Splice use-after-free fix in AF_UNIX frmo Hannes Frederic Sowa.

 5) Three ipv6 route handling bug fixes from Martin KaFai Lau:
    a) Don't create clone routes not managed by the fib6 tree
    b) Don't forget to check expiration of DST_NOCACHE routes.
    c) Handle rt->dst.from == NULL properly.

 6) Several AF_PACKET fixes wrt transport header setting and SKB
    protocol setting, from Daniel Borkmann.

 7) Fix thunder driver crash on shutdown, from Pavel Fedin.

 8) Several Mellanox driver fixes (max MTU calculations, use of correct
    DMA unmap in TX path, etc.) from Saeed Mahameed, Tariq Toukan, Doron
    Tsur, Achiad Shochat, Eran Ben Elisha, and Noa Osherovich.

 9) Several mv88e6060 DSA driver fixes (wrong bit definitions for
    certain registers, etc.) from Neil Armstrong.

10) Make sure to disable preemption while updating per-cpu stats of ip
    tunnels, from Jason A.  Donenfeld.

11) Various ARM64 bpf JIT fixes, from Yang Shi.

12) Flush icache properly in ARM JITs, from Daniel Borkmann.

13) Fix masking of RX and TX interrupts in ravb driver, from Masaru
    Nagai.

14) Fix netdev feature propagation for devices not implementing
    ->ndo_set_features().  From Nikolay Aleksandrov.

15) Big endian fix in vmxnet3 driver, from Shrikrishna Khare.

16) RAW socket code increments incorrect SNMP counters, fix from Ben
    Cartwright-Cox.

17) IPv6 multicast SNMP counters are bumped twice, fix from Neil Horman.

18) Fix handling of VLAN headers on stacked devices when REORDER is
    disabled.  From Vlad Yasevich.

19) Fix SKB leaks and use-after-free in ipvlan and macvlan drivers, from
    Sabrina Dubroca.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (83 commits)
  MAINTAINERS: Update Mellanox's Eth NIC driver entries
  net/core: revert "net: fix __netdev_update_features return.." and add comment
  af_unix: take receive queue lock while appending new skb
  rtnetlink: fix frame size warning in rtnl_fill_ifinfo
  net: use skb_clone to avoid alloc_pages failure.
  packet: Use PAGE_ALIGNED macro
  packet: Don't check frames_per_block against negative values
  net: phy: Use interrupts when available in NOLINK state
  phy: marvell: Add support for 88E1540 PHY
  arm64: bpf: make BPF prologue and epilogue align with ARM64 AAPCS
  macvlan: fix leak in macvlan_handle_frame
  ipvlan: fix use after free of skb
  ipvlan: fix leak in ipvlan_rcv_frame
  vlan: Do not put vlan headers back on bridge and macvlan ports
  vlan: Fix untag operations of stacked vlans with REORDER_HEADER off
  via-velocity: unconditionally drop frames with bad l2 length
  ipg: Remove ipg driver
  dl2k: Add support for IP1000A-based cards
  snmp: Remove duplicate OUTMCAST stat increment
  net: thunder: Check for driver data in nicvf_remove()
  ...

Eugenia (Jenny) Emantayev is replacing Amir Vadai as the
mlx4 Ethernet driver maintainer.

Saeed Mahameed is assigned to maintain mlx5 Eth functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 00ee5927 ("net: fix __netdev_update_features return
on ndo_set_features failure")
and adds a comment explaining why it's okay to return a value other than
0 upon error. Some drivers might actually change flags and return an
error so it's better to fire a spurious notification rather than miss
these.

CC: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While possibly in future we don't necessarily need to use
sk_buff_head.lock this is a rather larger change, as it affects the
af_unix fd garbage collector, diag and socket cleanups. This is too much
for a stable patch.

For the time being grab sk_buff_head.lock without disabling bh and irqs,
so don't use locked skb_queue_tail.

Fixes: 869e7c62 ("net: af_unix: implement stream sendpage support")
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reported-by: Eric Dumazet <edumazet@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the following warning:

  CC      net/core/rtnetlink.o
net/core/rtnetlink.c: In function ‘rtnl_fill_ifinfo’:
net/core/rtnetlink.c:1308:1: warning: the frame size of 2864 bytes is larger than 2048 bytes [-Wframe-larger-than=]
 }
 ^
by splitting up the huge rtnl_fill_ifinfo into some smaller ones, so we
don't have the huge frame allocations at the same time.

Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1. new skb only need dst and ip address(v4 or v6).
2. skb_copy may need high order pages, which is very rare on long running server.
Signed-off-by: Junwei Zhang <linggao.zjw@alibaba-inc.com>
Signed-off-by: Martin Zhang <martinbj2008@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use PAGE_ALIGNED(...) instead of open-coding it.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

rb->frames_per_block is an unsigned int, thus can never be negative.

Also fix spacing in the calculation of frames_per_block.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The NOLINK state will poll the phy once a second to see if the link
has come up. If the phy has an interrupt line, this polling can be
skipped, since the phy should interrupt when the link returns.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 88E1540 can be found embedded in the Marvell 88E6352 switch.  It
is compatible with the 88E1510, so add support for it, using the
88E1510 specific functions.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Save and restore FP/LR in BPF prog prologue and epilogue, save SP to FP
in prologue in order to get the correct stack backtrace.

However, ARM64 JIT used FP (x29) as eBPF fp register, FP is subjected to
change during function call so it may cause the BPF prog stack base address
change too.

Use x25 to replace FP as BPF stack base register (fp). Since x25 is callee
saved register, so it will keep intact during function call.
It is initialized in BPF prog prologue when BPF prog is started to run
everytime. Save and restore x25/x26 in BPF prologue and epilogue to keep
them intact for the outside of BPF. Actually, x26 is unnecessary, but SP
requires 16 bytes alignment.

So, the BPF stack layout looks like:

                                 high
         original A64_SP =>   0:+-----+ BPF prologue
                                |FP/LR|
         current A64_FP =>  -16:+-----+
                                | ... | callee saved registers
                                +-----+
                                |     | x25/x26
         BPF fp register => -80:+-----+
                                |     |
                                | ... | BPF prog stack
                                |     |
                                |     |
         current A64_SP =>      +-----+
                                |     |
                                | ... | Function call stack
                                |     |
                                +-----+
                                  low

CC: Zi Shen Lim <zlim.lnx@gmail.com>
CC: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Yang Shi <yang.shi@linaro.org>
Acked-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>