Merge tag 'omap-for-v3.13/hwmod-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc

From Tony Lindgren:
omap hwmod related changes via Paul Walmsley <paul@pwsan.com>:

Some OMAP hwmod changes for 3.13.  Significant changes here include:

- support for moving some of the hwmod flags to DT data

- support for the SSI, hardware spinlock, USB host/TLL, and RNG IP
  blocks for various OMAPs

- a fix that again decouples hwmod data changes from unrelated DT data
  patchsets

Basic test logs are available at:

http://www.pwsan.com/omap/testlogs/prcm_fixes_v3.13/20131009094936/

* tag 'omap-for-v3.13/hwmod-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP5: hwmod: add missing ocp2scp hwmod data
  ARM: AM33xx: hwmod: Add RNG module data
  ARM: OMAP2+: hwmod: Extract no-idle and no-reset info from DT
  ARM: OMAP2+: hwmod: cleanup HWMOD_INIT_NO_RESET usage
  ARM: AM33xx: hwmod_data: add the sysc configuration for spinlock
  ARM: OMAP5: hwmod data: Add spinlock data
  ARM: OMAP5: hwmod data: Add USB Host and TLL modules
  ARM: OMAP2+: hwmod data: Add SSI information
  ARM: OMAP2+: hwmod: check for module address space during init

initcalls need to have platform specific checks so they are not run in
multi-platform builds.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>

Add this hwmod data to allow USB3 to work in OMAP5 boards.
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
[tony@atomide.com: updated to apply against Paul's changes]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Merge tag 'keystone-soc-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/soc

From Santosh Shilimkar:
SOC updates for Keystone II devices:

- Clock tree support
- Clock management support using PM core
- Keystone config update for EMDA with ack from Vinod
- Enable SPI and I2C drivers

* tag 'keystone-soc-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone: (510 commits)
  ARM: keystone: Enable I2C and SPI bus support
  ARM: keystone: Select TI_EDMA to be able to enable SPI driver
  dma: Allow TI_EDMA selectable for ARCH_KEYSTONE
  ARM: dts: keystone: Add the SPI nodes
  ARM: dts: keystone: Add i2c device nodes
  ARM: keystone: add PM domain support for clock management
  ARM: keystone: Enable clock drivers
  ARM: dts: keystone: Add clock phandle to UART nodes
  ARM: dts: keystone: Add clock tree data to devicetree
  +Linux 3.12-rc4
Signed-off-by: Kevin Hilman <khilman@linaro.org>

Merge tag 'for-v3.13/hwmod' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.13/hwmod

Some OMAP hwmod changes for 3.13.  Significant changes here include:

- support for moving some of the hwmod flags to DT data

- support for the SSI, hardware spinlock, USB host/TLL, and RNG IP
  blocks for various OMAPs

- a fix that again decouples hwmod data changes from unrelated DT data
  patchsets

Basic test logs are available at:

http://www.pwsan.com/omap/testlogs/prcm_fixes_v3.13/20131009094936/

The summary reports that the 4460varsomom boots are failing, but this looks
incorrect - it's probably a bug in the validation scripts here.

Keystone I2C dnd SPI driver updates are already merged so lets
enable them in config.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

Select the TI EDMA to be able to enable SPI driver on Keystone
SOCs. Keystone SOCs share the EDMA IP with other TI SOCs.

Note that EDMA support hasn't been added and tested yet for
Keystone SOC data(device tree), but building it, is harmless since
driver like SPI already takes care of supporting non-dma mode
in the absence of such data.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

Allow the TI_EDMA to be built for ARCH_KEYSTONE which also supports
the EDMA IP.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

Keystone2 based SOCs supports 3 instances of SPI controllers. Add
the device nodes for them.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

Keystone2 based SOCs supports 3 instances of i2c controllers. Add
the device nodes for them. The i2c0 child device AT24C1024 EEPROM node
is also added. When different board variants are added in future, it
can be moved to the supported boards from common SOC file.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

Add runtime PM core support to Keystone SOCs by using the pm_clk
infrastructure of the PM core. Patch is based on Kevin's pm_domain
work on DaVinci SOCs.

Keystone SOC doesn't have depedency to enable clocks in early
in the boot and hence the clock and PM domain initialisation is done
at subsys_init() level.

Cc: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

Merge tag 'renesas-soc2-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc

From Simon Horman:
Second Round of Renesas ARM based SoC updates for v3.13

* SMP support for r8a7791 SoC
* r8a7779_init_irq_extpin() for DT for r8a7779 and r8a7778 SoCs
* Add HPB-DMAC to r8a7779 and r8a7778 SoCs
* Add r7s72100 SoC
* Make use of ARCH timer workaround on r8a7791 SoC
* Add IRQC platform device support to r8a7791 SoC
* Add I2C clocks and aliases for the DT mode for r8a7790 SoC
* Add MAC platform device to r8a73a4 SoC

* tag 'renesas-soc2-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: r8a7791 SMP support
  ARM: shmobile: r8a7779: split r8a7779_init_irq_extpin() for DT
  ARM: shmobile: r8a7778: split r8a7778_init_irq_extpin() for DT
  ARM: shmobile: r7s72100 SCIF support
  ARM: shmobile: Initial r7s72100 SoC support
  ARM: shmobile: r8a7791 Arch timer workaround
  ARM: shmobile: r8a7791 IRQC platform device support
  ARM: shmobile: Introduce r8a7791_add_standard_devices()
  ARM: shmobile: Break out R-Car Gen2 setup code
  ARM: shmobile: r8a73a4: add a clock alias for the DMAC in DT mode
  ARM: shmobile: r8a7790: add I2C clocks and aliases for the DT mode
  ARM: shmobile: r8a7779: add HPB-DMAC support
  ARM: shmobile: r8a7778: add HPB-DMAC support
  ARM: shmobile: r8a73a4: add a DMAC platform device and clock for it
  ARM: shmobile: Remove #gpio-ranges-cells DT property
  gpio: rcar: Remove #gpio-range-cells DT property usage
  ARM: shmobile: armadillo: fixup ether pinctrl naming
  ARM: shmobile: Lager: add Micrel KSZ8041 PHY fixup
  ARM: shmobile: update SDHI DT compatibility string to the <unit>-<soc> format
Signed-off-by: Kevin Hilman <khilman@linaro.org>

Add RNG hwmod data for AM33xx SoC.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Now that we have DT bindings to specify which devices should not
be reset and idled during init, make hwmod extract the information
(and store them in internal flags) from Device tree.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

For modules/IPs/hwmods which do not have
-1- sys->class->reset()
and
-2- hardreset lines
and
-3- No way to do an ocp reset (no sysc control)
the flag 'HWMOD_INIT_NO_RESET' is not much useful.

Cleanup all such instances across various hwmod data files.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Add the missing sysc configuration to the AM335 spinlock hwmod
data. This ensures that smart-idle is enabled whenever the module
is enabled by the driver.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Add the hwmod data for the spinlock IP in OMAP5 SoC.
This is needed to be able to enable the OMAP spinlock
support for OMAP5.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Add hwmod data for High Speed USB host and TLL modules

CC: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

This patch adds Synchronous Serial Interface (SSI) hwmod support for
OMAP34xx SoCs.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

The hwmod init sequence involves initializing and idling all the
hwmods during bootup. If a module class has sysconfig, the init
sequence utilizes the module register base for performing any
sysc configuration.

The module address space is being removed from hwmod database and
retrieved from the <reg> property of the corresponding DT node.
If a hwmod does not have its corresponding DT node defined and the
memory address space is not defined in the corresponding
omap_hwmod_ocp_if, then the module register target address space
would be NULL and any sysc programming would result in a NULL
pointer dereference and a kernel boot hang.

Handle this scenario by checking for a valid module address space
during the _init of each hwmod, and leaving it in the registered
state if no module register address base is defined in either of
the hwmod data or the DT data.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
[paul@pwsan.com: use -ENXIO rather than -ENOMEM to indicate a missing address
 space error; fixed checkpatch.pl problem]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Enable common clock drivers on Keystone 2 based SOCs.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

Now since the clock tree is added, update UART dt nodes with clock data
and remove the hard coded clock frequency.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

Add clock tree for Keystone 2 based SOCs.

Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

Tie in the APMU SMP code on r8a7791. When used together
with the secondary CPU device node and smp_ops in the
board specific code then this will allow use of the
two Cortex-A15 cores in the r8a7791 SoC.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

r8a7779 INTC needs IRL pin mode settings to determine
behavior of IRQ0 - IRQ3, and r8a7779_init_irq_extpin()
is controlling it via irlm parameter.
But this function registers renesas_intc_irqpin driver
if irlm was set, and this value depends on platform.
This is not good for DT.
This patch splits r8a7779_init_irq_extpin() function
into "mode settings" and "funtion register" parts
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

r8a7778 INTC needs IRL pin mode settings to determine
behavior of IRQ0 - IRQ3, and r8a7778_init_irq_extpin()
is controlling it via irlm parameter.
But this function registers renesas_intc_irqpin driver
if irlm was set, and this value depends on platform.
This is not good for DT.
This patch splits r8a7778_init_irq_extpin() function
into "mode settings" and "funtion register" parts.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add SCIF serial port support to the r7s72100 SoC by
adding platform devices for SCIF0 -> SCIF7 together with
clock bindings. DT device description is excluded at
this point since such bindings are still under
development.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add initial support for the r7272100 SoC including:
 - Single Cortex-A9 CPU Core
 - GIC

No static virtual mappings are used, all the components
make use of ioremap(). DT_MACHINE_START is still wrapped
in CONFIG_USE_OF to match other mach-shmobile code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Make use of the R-Car Gen2 arch timer workaround on r8a7791.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a platform device for the r8a7791 IRQC hardware
driving IRQ pins IRQ0 to IRQ9. The Linux interrupt
number is statically assigned to allow board code
written in C to make use of static interrupt numbers.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Introduce the function r8a7791_add_standard_devices() that
follows the same style as other mach-shmobile SoC code and
allows C version of board code to add on-chip devices.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Move arch timer workaround code and boot mode pin
handling from setup-r8a7790.c to setup-rcar-gen2.c.

With this in place the same code can be used on
other R-Car Generation 2 devices such as r8a7791.
Signed-off-by: Magnus Damm <damm@opensource.se>
[horms+renesas@verge.net.au trivial rebase of board-lager.c
 for introduction of lager_add_standard_devices()]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Devices, initialised from the Device Tree and from platform code usually
have different names. This patch adds a clock alias for DMAC on r8a73a4
in DT mode.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds clock definitions for the 4 I2C interfaces on r8a7790 and
clock aliases, suitable for the DT mode.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add HPB-DMAC platform device on R8A7779 SoC along with its slave and channel
configurations (only for SDHI0 so far).
Signed-off-by: Max Filippov <max.filippov@cogentembedded.com>
[Sergei: moved *enum* declaring HPB-DMAC slave IDs from now removed <mach/dma.h>
to <mach/r8a7779.h>, removed #include <mach/dma.h> from setup-r8a7779.c, removed
SSI-related *enum* values and SSI-related data from hpb_dmae_slaves[] and
hpb_dmae_channels[], added ASYNCMDR.ASBTMD{20|24|43} and ASYNCMDR.ASMD{20|24|43}
fields/values, fixed comments to ASYNCMDR.ASBTMD2[123] and ASYNCMDR.ASMD2[123]
fields/values, renamed all the bit/field/value #define's to include 'HBP_DMAE_'
prefix to match the driver, moved comments after the element initializers of
hpb_dmae_channels[].]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add HPB-DMAC platform device on R8A7778 SoC along with its slave and channel
configurations (only for SDHI0 so far).
Signed-off-by: Max Filippov <max.filippov@cogentembedded.com>
[Sergei: moved *enum* declaring HPB-DMAC slave IDs from now removed <mach/dma.h>
to <mach/r8a7778.h>, removed #include <mach/dma.h> from setup-r8a7778.c, removed
SSI-related *enum* values and SSI-related data from hpb_dmae_slaves[] and
hpb_dmae_channels[], moved the comments after the element initializers of
hpb_dmae_channels[].]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a DMAC platform device and clock definitions for it on r8a73a4.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Fourth Round of Renesas ARM based SoC fixes for v3.12

* Remove unused #gpio-ranges-cells DT property

* Remove usage of deprecated #gpio-range-cells DT property
  from GPIO R-Car

  Property was deprecated in v3.11-rc2

* Correct ether pinctl naming for armadillo800eva board

  Regression introduced in v3.10-rc5

* Add Micrel KSZ8041 PHY fixup to lager board

  This resolves a problem that has been present since 3.11-rc2

* Update SDHI DT compatibility string to the <unit>-<soc> format

  This makes compatibility strings consistent across all renesas
  hardware which currently supports DT.

  The bindings which are being updated where intorodiced on
  a per-SoC basis starting in v3.8-rc7. They may have
  been internally consistent when originally added.

Renesas ARM based SoC SMP updates for v3.13

* Add CPU notifier based SCU boot vector code
  - Use on emev2, r8a7779 and sh73a0 SoCs
  - Remove now unused shmobile_smp_scu_boot_secondary()
* Add shared APMU SMP support code
  - Use to add SMP support for r8a7790 SoC
* Introduce shmobile_boot_size
* Expose shmobile_invalidate_start()
* Introduce shmobile_smp_cpu_disable()
  - Use on sh73a0 SoC
  - Remove now unused shmobile_smp_init_cpus()

Merge tag 'renesas-smp-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc

From Simon Horman:
Renesas ARM based SoC SMP updates for v3.13

* Add CPU notifier based SCU boot vector code
  - Use on emev2, r8a7779 and sh73a0 SoCs
  - Remove now unused shmobile_smp_scu_boot_secondary()
* Add shared APMU SMP support code
  - Use to add SMP support for r8a7790 SoC
* Introduce shmobile_boot_size
* Expose shmobile_invalidate_start()
* Introduce shmobile_smp_cpu_disable()
  - Use on sh73a0 SoC
  - Remove now unused shmobile_smp_init_cpus()

* tag 'renesas-smp-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: Include CA7 cores in APMU table
  ARM: shmobile: Extend APMU code to allow single cluster only
  ARM: shmobile: Remove shmobile_smp_scu_boot_secondary()
  ARM: shmobile: Let r8a7779 rely on SCU CPU notifier
  ARM: shmobile: Let EMEV2 rely on SCU CPU notifier
  ARM: shmobile: Let sh73a0 rely on SCU CPU notifier
  ARM: shmobile: Add CPU notifier based SCU boot vector code
  ARM: shmobile: Add r8a7790 SMP support using APMU code
  ARM: shmobile: Shared APMU SMP support code without DT
  ARM: shmobile: Introduce shmobile_boot_size
  ARM: shmobile: Expose shmobile_invalidate_start()
  ARM: shmobile: Remove unused shmobile_smp_init_cpus()
  ARM: shmobile: Use shmobile_smp_cpu_disable() on sh73a0
  ARM: shmobile: Introduce shmobile_smp_cpu_disable()
  ARM: shmobile: r8a7790: Constify platform data and resources
  ARM: shmobile: Rename to r8a7790_init_early()
  ARM: shmobile: Rename to r8a73a4_init_early()
Signed-off-by: Olof Johansson <olof@lixom.net>