Skip to content

L
linux
Switch branch/tag
  1. 09 May, 2022 5 commits
  3. 04 May, 2022 4 commits
  5. 29 Apr, 2022 1 commit
    • Wen Gong's avatar
      ath11k: reduce the wait time of 11d scan and hw scan while add interface · bb300130
      Wen Gong authored 
      (cherry picked from commit 1f682dc9 in wireless-next)

Currently ath11k will wait 11d scan complete while add interface in
ath11k_mac_op_add_interface(), when system resume without enable
wowlan, ath11k_mac_op_add_interface() is called for each resume, thus
it increase the resume time of system. And ath11k_mac_op_hw_scan()
after ath11k_mac_op_add_interface() also needs some time cost because
the previous 11d scan need more than 5 seconds when 6 GHz is enabled,
then the scan started event will indicated to ath11k after the 11d
scan completed.

While 11d scan/hw scan is running in firmware, if ath11k update channel
list to firmware by WMI_SCAN_CHAN_LIST_CMDID, then firmware will cancel
the current scan which is running, it lead the scan failed. The patch
commit 9dcf6808 ("ath11k: add 11d scan offload support") used
finish_11d_scan/finish_11d_ch_list/pending_11d to synchronize the 11d
scan/hw scan/channel list between ath11k/firmware/mac80211 and to avoid
the scan fail.

Add wait operation before ath11k update channel list, function
ath11k_reg_update_chan_list() will wait until the current 11d scan/hw
scan completed. And remove the wait operation of start 11d scan and
waiting channel list complete in hw scan. After these changes, resume
time cost reduce about 5 seconds and also hw scan time cost reduced
obviously, and scan failed not seen.

The 11d scan is sent to firmware only one time for each interface added
in mac.c, and it is moved after the 1st hw scan because 11d scan will
cost some time and thus leads the AP scan result update to UI delay.
Currently priority of ath11k's hw scan is WMI_SCAN_PRIORITY_LOW, and
priority of 11d scan in firmware is WMI_SCAN_PRIORITY_MEDIUM, then the
11d scan which sent after hw scan will cancel the hw scan in firmware,
so change the priority to WMI_SCAN_PRIORITY_MEDIUM for the hw scan which
is in front of the 11d scan, thus it will not happen scan cancel in
firmware.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3

Fixes: 9dcf6808 ("ath11k: add 11d scan offload support")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215777
Cc: <stable@vger.kernel.org>
Signed-off-by: default avatarWen Gong <quic_wgong@quicinc.com>
Signed-off-by: default avatarKalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328035832.14122-1-quic_wgong@quicinc.comSigned-off-by: default avatarKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220427111619.9758-1-kvalo@kernel.org
      bb300130
  7. 23 Apr, 2022 2 commits
  9. 13 Apr, 2022 7 commits
    • Lin Ma's avatar
      nfc: nci: add flush_workqueue to prevent uaf · ef27324e
      Lin Ma authored 
      Our detector found a concurrent use-after-free bug when detaching an
NCI device. The main reason for this bug is the unexpected scheduling
between the used delayed mechanism (timer and workqueue).

The race can be demonstrated below:

Thread-1                           Thread-2
                                 | nci_dev_up()
                                 |   nci_open_device()
                                 |     __nci_request(nci_reset_req)
                                 |       nci_send_cmd
                                 |         queue_work(cmd_work)
nci_unregister_device()          |
  nci_close_device()             | ...
    del_timer_sync(cmd_timer)[1] |
...                              | Worker
nci_free_device()                | nci_cmd_work()
  kfree(ndev)[3]                 |   mod_timer(cmd_timer)[2]

In short, the cleanup routine thought that the cmd_timer has already
been detached by [1] but the mod_timer can re-attach the timer [2], even
it is already released [3], resulting in UAF.

This UAF is easy to trigger, crash trace by POC is like below

[   66.703713] ==================================================================
[   66.703974] BUG: KASAN: use-after-free in enqueue_timer+0x448/0x490
[   66.703974] Write of size 8 at addr ffff888009fb7058 by task kworker/u4:1/33
[   66.703974]
[   66.703974] CPU: 1 PID: 33 Comm: kworker/u4:1 Not tainted 5.18.0-rc2 #5
[   66.703974] Workqueue: nfc2_nci_cmd_wq nci_cmd_work
[   66.703974] Call Trace:
[   66.703974]  <TASK>
[   66.703974]  dump_stack_lvl+0x57/0x7d
[   66.703974]  print_report.cold+0x5e/0x5db
[   66.703974]  ? enqueue_timer+0x448/0x490
[   66.703974]  kasan_report+0xbe/0x1c0
[   66.703974]  ? enqueue_timer+0x448/0x490
[   66.703974]  enqueue_timer+0x448/0x490
[   66.703974]  __mod_timer+0x5e6/0xb80
[   66.703974]  ? mark_held_locks+0x9e/0xe0
[   66.703974]  ? try_to_del_timer_sync+0xf0/0xf0
[   66.703974]  ? lockdep_hardirqs_on_prepare+0x17b/0x410
[   66.703974]  ? queue_work_on+0x61/0x80
[   66.703974]  ? lockdep_hardirqs_on+0xbf/0x130
[   66.703974]  process_one_work+0x8bb/0x1510
[   66.703974]  ? lockdep_hardirqs_on_prepare+0x410/0x410
[   66.703974]  ? pwq_dec_nr_in_flight+0x230/0x230
[   66.703974]  ? rwlock_bug.part.0+0x90/0x90
[   66.703974]  ? _raw_spin_lock_irq+0x41/0x50
[   66.703974]  worker_thread+0x575/0x1190
[   66.703974]  ? process_one_work+0x1510/0x1510
[   66.703974]  kthread+0x2a0/0x340
[   66.703974]  ? kthread_complete_and_exit+0x20/0x20
[   66.703974]  ret_from_fork+0x22/0x30
[   66.703974]  </TASK>
[   66.703974]
[   66.703974] Allocated by task 267:
[   66.703974]  kasan_save_stack+0x1e/0x40
[   66.703974]  __kasan_kmalloc+0x81/0xa0
[   66.703974]  nci_allocate_device+0xd3/0x390
[   66.703974]  nfcmrvl_nci_register_dev+0x183/0x2c0
[   66.703974]  nfcmrvl_nci_uart_open+0xf2/0x1dd
[   66.703974]  nci_uart_tty_ioctl+0x2c3/0x4a0
[   66.703974]  tty_ioctl+0x764/0x1310
[   66.703974]  __x64_sys_ioctl+0x122/0x190
[   66.703974]  do_syscall_64+0x3b/0x90
[   66.703974]  entry_SYSCALL_64_after_hwframe+0x44/0xae
[   66.703974]
[   66.703974] Freed by task 406:
[   66.703974]  kasan_save_stack+0x1e/0x40
[   66.703974]  kasan_set_track+0x21/0x30
[   66.703974]  kasan_set_free_info+0x20/0x30
[   66.703974]  __kasan_slab_free+0x108/0x170
[   66.703974]  kfree+0xb0/0x330
[   66.703974]  nfcmrvl_nci_unregister_dev+0x90/0xd0
[   66.703974]  nci_uart_tty_close+0xdf/0x180
[   66.703974]  tty_ldisc_kill+0x73/0x110
[   66.703974]  tty_ldisc_hangup+0x281/0x5b0
[   66.703974]  __tty_hangup.part.0+0x431/0x890
[   66.703974]  tty_release+0x3a8/0xc80
[   66.703974]  __fput+0x1f0/0x8c0
[   66.703974]  task_work_run+0xc9/0x170
[   66.703974]  exit_to_user_mode_prepare+0x194/0x1a0
[   66.703974]  syscall_exit_to_user_mode+0x19/0x50
[   66.703974]  do_syscall_64+0x48/0x90
[   66.703974]  entry_SYSCALL_64_after_hwframe+0x44/0xae

To fix the UAF, this patch adds flush_workqueue() to ensure the
nci_cmd_work is finished before the following del_timer_sync.
This combination will promise the timer is actually detached.

Fixes: 6a2968aa ("NFC: basic NCI protocol implementation")
Signed-off-by: default avatarLin Ma <linma@zju.edu.cn>
Reviewed-by: default avatarKrzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      ef27324e
    • Alvin Šipraga's avatar
      net: dsa: realtek: don't parse compatible string for RTL8366S · 8e925de6
      Alvin Šipraga authored 
      This switch is not even supported, but if someone were to actually put
this compatible string "realtek,rtl8366s" in their device tree, they
would be greeted with a kernel panic because the probe function would
dereference NULL. So let's just remove it.

Link: https://lore.kernel.org/all/CACRpkdYdKZs0WExXc3=0yPNOwP+oOV60HRz7SRoGjZvYHaT=1g@mail.gmail.com/Signed-off-by: default avatarAlvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      8e925de6
    • Alvin Šipraga's avatar
      net: dsa: realtek: fix Kconfig to assure consistent driver linkage · 2511e0c8
      Alvin Šipraga authored 
      The kernel test robot reported a build failure:

or1k-linux-ld: drivers/net/dsa/realtek/realtek-smi.o:(.rodata+0x16c): undefined reference to `rtl8366rb_variant'

... with the following build configuration:

CONFIG_NET_DSA_REALTEK=y
CONFIG_NET_DSA_REALTEK_SMI=y
CONFIG_NET_DSA_REALTEK_RTL8365MB=y
CONFIG_NET_DSA_REALTEK_RTL8366RB=m

The problem here is that the realtek-smi interface driver gets built-in,
while the rtl8366rb switch subdriver gets built as a module, hence the
symbol rtl8366rb_variant is not reachable when defining the OF device
table in the interface driver.

The Kconfig dependencies don't help in this scenario because they just
say that the subdriver(s) depend on at least one interface driver. In
fact, the subdrivers don't depend on the interface drivers at all, and
can even be built even in their absence. Somewhat strangely, the
interface drivers can also be built in the absence of any subdriver,
BUT, if a subdriver IS enabled, then it must be reachable according to
the linkage of the interface driver: effectively what the IS_REACHABLE()
macro achieves. If it is not reachable, the above kind of linker error
will be observed.

Rather than papering over the above build error by simply using
IS_REACHABLE(), we can do a little better and admit that it is actually
the interface drivers that have a dependency on the subdrivers. So this
patch does exactly that. Specifically, we ensure that:

1. The interface drivers' Kconfig symbols must have a value no greater
   than the value of any subdriver Kconfig symbols.

2. The subdrivers should by default enable both interface drivers, since
   most users probably want at least one of them; those interface
   drivers can be explicitly disabled however.

What this doesn't do is prevent a user from building only a subdriver,
without any interface driver. To that end, add an additional line of
help in the menu to guide users in the right direction.

Link: https://lore.kernel.org/all/202204110757.XIafvVnj-lkp@intel.com/Reported-by: default avatarkernel test robot <lkp@intel.com>
Fixes: aac94001 ("net: dsa: realtek: add new mdio interface for drivers")
Signed-off-by: default avatarAlvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      2511e0c8
    • David S. Miller's avatar
      Merge tag 'wireless-2022-04-13' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless · dad32cfe
      David S. Miller authored 
      Kalle Valo says:

====================
wireless fixes for v5.18

First set of fixes for v5.18. Maintainers file updates, two
compilation warning fixes, one revert for ath11k and smaller fixes to
drivers and stack. All the usual stuff.
====================
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      dad32cfe
    • Dylan Hung's avatar
      net: ftgmac100: access hardware register after clock ready · 3d250452
      Dylan Hung authored 
      AST2600 MAC register 0x58 is writable only when the MAC clock is
enabled.  Usually, the MAC clock is enabled by the bootloader so
register 0x58 is set normally when the bootloader is involved.  To make
ast2600 ftgmac100 work without the bootloader, postpone the register
write until the clock is ready.

Fixes: 137d23ce ("net: ftgmac100: Fix Aspeed ast2600 TX hang issue")
Signed-off-by: default avatarDylan Hung <dylan_hung@aspeedtech.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      3d250452
    • Vladimir Oltean's avatar
      Revert "net: dsa: setup master before ports" · 762c2998
      Vladimir Oltean authored 
      This reverts commit 11fd667d.

dsa_slave_change_mtu() updates the MTU of the DSA master and of the
associated CPU port, but only if it detects a change to the master MTU.

The blamed commit in the Fixes: tag below addressed a regression where
dsa_slave_change_mtu() would return early and not do anything due to
ds->ops->port_change_mtu() not being implemented.

However, that commit also had the effect that the master MTU got set up
to the correct value by dsa_master_setup(), but the associated CPU port's
MTU did not get updated. This causes breakage for drivers that rely on
the ->port_change_mtu() DSA call to account for the tagging overhead on
the CPU port, and don't set up the initial MTU during the setup phase.

Things actually worked before because they were in a fragile equilibrium
where dsa_slave_change_mtu() was called before dsa_master_setup() was.
So dsa_slave_change_mtu() could actually detect a change and update the
CPU port MTU too.

Restore the code to the way things used to work by reverting the reorder
of dsa_tree_setup_master() and dsa_tree_setup_ports(). That change did
not have a concrete motivation going for it anyway, it just looked
better.

Fixes: 066dfc42 ("Revert "net: dsa: stop updating master MTU from master.c"")
Signed-off-by: default avatarVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      762c2998
    • Martin Willi's avatar
      macvlan: Fix leaking skb in source mode with nodst option · e16b8598
      Martin Willi authored 
      The MACVLAN receive handler clones skbs to all matching source MACVLAN
interfaces, before it passes the packet along to match on destination
based MACVLANs.

When using the MACVLAN nodst mode, passing the packet to destination based
MACVLANs is omitted and the handler returns with RX_HANDLER_CONSUMED.
However, the passed skb is not freed, leaking for any packet processed
with the nodst option.

Properly free the skb when consuming packets to fix that leak.

Fixes: 427f0c8c ("macvlan: Add nodst option to macvlan type source")
Signed-off-by: default avatarMartin Willi <martin@strongswan.org>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      e16b8598
  11. 12 Apr, 2022 14 commits
  13. 11 Apr, 2022 7 commits
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7