Thierry writes:
"Add support for 2 hardware overlays found on Tegra. These support YUV
pixel formats and can be used as video overlays. .mode_set_base() is
implemented and support for VBLANK and page-flipping is added.

A few minor bug fixes are also included and a new debugfs file allows
to inspect the framebuffers attached to the Tegra DRM device."

* 'drm/tegra-for-3.9' of git://anongit.freedesktop.org/tegra/linux:
  drm/tegra: Add list of framebuffers to debugfs
  drm/tegra: Fix color expansion
  drm/tegra: Split DC_CMD_STATE_CONTROL register write
  drm/tegra: Implement page-flipping support
  drm/tegra: Implement VBLANK support
  drm/tegra: Implement .mode_set_base()
  drm/tegra: Add plane support
  drm/tegra: Remove bogus tegra_framebuffer structure
  drm: Add consistency check for page-flipping

This list is most useful to inspect whether framebuffer reference
counting works as expected. The code is loosely based on the i915
implementation.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>

bpp stores the number of bytes per pixel, but color expansion needs to
be enabled for less than 24 bits per pixel.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>

The Tegra TRM says that the ACT_REQ and UPDATE fields cannot be
programmed at the same time so they are updated in two consecutive
writes instead.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>

All the necessary support bits like .mode_set_base() and VBLANK are now
available, so page-flipping case easily be implemented on top.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>

Implement support for the VBLANK IOCTL. Note that Tegra is somewhat
special in this case because it doesn't use the generic IRQ support
provided by the DRM core (DRIVER_HAVE_IRQ) but rather registers one
interrupt handler for each display controller.

While at it, clean up the way that interrupts are enabled to ensure
that the VBLANK interrupt only gets enabled when required.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>

The sequence for replacing the scanout buffer is much shorter than a
full mode change operation so implementing this callback considerably
speeds up cases where only a new framebuffer is to be scanned out.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>

Add support for the B and C planes which support RGB and YUV pixel
formats and can be used as overlays or hardware cursor. Currently 32-bit
XRGB as well as UYVY, YUV420 and YUV422 pixel formats are advertised.
Other formats should be easy to add but these are the most common ones
and should cover the majority of use-cases.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>

Tegra uses the CMA FB helpers so framebuffers passed to the driver need
to use the corresponding functions to access the underlying GEM objects.

This used to work because struct tegra_framebuffer was sufficiently
similar to struct drm_fb_cma but that isn't guaranteed to stay that way.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>

Driver implementations of the drm_crtc's .page_flip() function are
required to update the crtc->fb field on success to reflect that the new
framebuffer is now in use. This is important to keep reference counting
on the framebuffers balanced.

While at it, document this requirement to keep others from falling into
the same trap.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Merge branch 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-next

The summary:
. Add display mode check operaion to mixer driver
  - Mixer IP also can put certain restrictions on the proposed
    display modes and these restrictions need to be considered
    during mode negotiation, which happens immediately after
    edid parsing.
. Set correct mode for range of resolutions
  - With this patch, the mixer driver could find the correct mode
    for the range of resolutions upto 1080 vertical lines.
. Support extra resolution for hdmi
  - This patch programs the core and timing generator registers
    using the timing data provided in drm_display_mode without
    hard-coded configurations. So this patch adds additional PHY
    configs to allow us to support more permissible resolutions
    and refresh rates.
. Add device tree support for g2d
  - This patch adds just the compatible string for exynos5250 SoC
    so that with device tree enabling, this driver can be probed.
. And bug fixes and code cleanups.

* 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
  drm/exynos: Add device tree based discovery support for G2D
  drm/exynos: hdmi: support extra resolutions using drm_display_mode timings
  drm/exynos: mixer: set correct mode for range of resolutions
  drm/exynos: implement display-mode-check callback in mixer driver
  drm/exynos: add display-mode-check operation to exynos_mixer_ops struct
  drm/exynos: release resources properly when fb creation is failed.
  drm/exynos: fix wrong pointer access at vm close.
  drm/exynos: Add missing braces around sizeof
  drm/exynos: consider exception case to fb handle creation
  drm/exynos: fix iommu address allocation order

The values of n, m1 and m2 needs to be subtracted by 2 before writing them to
the FP register. The dot clock calculation already thinks of these values in
register form so we must also specify them as such.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

This patch adds device tree match table for Exynos G2D controller.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

This patch programs the core and timing generator registers using the
timing data provided in drm_display_mode and not using hard-coded
configurations.

Additional PHY configs has been added. This allows us to support more
permissible resolutions and refresh rates.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Shirish S <s.shirish@samsung.com>
Signed-off-by: Akshay Saraswat <Akshay.s@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

With this patch, mixer driver find the correct resolution mode for
the range of resolutions, upto 1080 vertical lines. Resolution will
be categorized to NTSC SD, PAL SD or HD and the correct mode is
set to the mixer configuration register.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

This patch adds the implementation of check_timing callback in the mixer
driver. Based on the mixer version, correct set of restrictions will be
exposed by the mixer driver. A resolution will be acceptable only if passes
the criteria set by mixer and hdmi IPs.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

This patch adds the display mode check operation to exynos_mixer_ops
in drm-common-hdmi. In Exynos SoCs, mixer IP can put certain restrictions
on the proposed display modes. These restriction needs to be considered
during mode negotiation, which happens immediately after edid parsing.

Both, mixer check-mode and hdmi check-timing callbacks are called one after
another and ANDed result is returned back.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

This patch releases allocated resources properly when
exynos_user_fb_create() is failed.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>

This patch fixes wrong pointer access issue to filp->f_op and
filp->private_data.

The exynos_drm_gem_mmap_ioctl() changes filp->f_op and
filp->private_data temporarily and restore them to use
original ones in exynos_drm_gem_mmap_buffer() but there
was no lock between the changing and the restoring so
wrong pointer access to filp->f_op and filp->private_data
was induced by vm close callback.

So this patch uses mutex lock properly to resolve this issue.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>

Fixes the following checkpatch warning:
WARNING: sizeof *sgt should be sizeof(*sgt)
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

GETFB ioctl request creates a new handle to only one gem object
so it should check if the given fb has one gem object.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>

This patch modifies iommu address allocation order from 64k
to 4k. 64k order causes waste of the io space and this was
our mistakes.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>

KMS driver for TI LCD controller

* 'tilcdc-next' of git://people.freedesktop.org/~robclark/linux:
  drm/tilcdc: add support for LCD panels (v5)
  drm/tilcdc: add encoder slave (v2)
  drm/i2c: nxp-tda998x (v3)
  drm/tilcdc: add TI LCD Controller DRM driver (v4)
  drm/nouveau: use i2c encoder helper wrappers
  drm: i2c encoder helper wrappers
  drm/cma: add debugfs helpers
  drm: small fix in drm_send_vblank_event()
  drm: Don't set the plane->fb to NULL on successfull set_plane
  drm/cma-helper: fixup compilation

Conflicts:
	drivers/gpu/drm/Kconfig
	drivers/gpu/drm/Makefile
	drivers/gpu/drm/drm_fb_cma_helper.c

More drm-next bits for radeon.  Just bug fixes.

* 'drm-next-3.9' of git://people.freedesktop.org/~agd5f/linux:
  drm/radeon: properly validate the atpx interface
  drm/radeon: switch get_gpu_clock() to a callback (v2)
  drm/radeon: add a asic callback to get the xclk
  drm/radeon: Avoid NULL pointer dereference from atom_index_iio() allocation failure
  drm/radeon: remove overzealous warning in hdmi handling
  drm/radeon: fix multi-head power profile stability on BTC+ asics

Merge branch 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-next

restore debugfs vbios, fix multiple actions with supervisor intrs

* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
  drm/nouveau: restore debugfs/vbios.rom support
  drm/nv50-/kms: remove UPDATE methods after each encoder disconnect
  drm/nvd0/disp: handle multiple actions from one set of supervisor intrs
  drm/nv50/disp: handle multiple actions from one set of supervisor intrs

Some bioses don't set the function mask correctly
which caused required functions to be disabled.

Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=53111Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Cleans up the code for future asics

v2: rebase, fix some missing radeon_asic updates
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This is required to get the reference clock used
by the gfx engine for things like timestamps. Fixes
support for GL extensions the use timestamps on
certain boards.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Smatch anlysis:

drivers/gpu/drm/radeon/atom.c:1242 atom_index_iio() error: potential null
 dereference 'ctx->iio'.  (kzalloc returns null)

Also cleaned up some checks before calls to kfree(). kfree(NULL) is OK.

Cc: David Airlie <airlied@linux.ie>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Michel Dänzer" <michel.daenzer@amd.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

hdmi audio works fine.  The warning just confuses users.

fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=44341Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable@vger.kernel.org

vddci needs to track mclk for multi-head.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>

Supervisor can now handle more than one operation within a single
series of interrupts.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

In v3.3, the gma500 drm driver moved from staging to drm group by
Alan Cox's 3abcf41f patch. the gma500 drm driver should control
brightness well and don't need gma500 stub driver anymore.

Reference:
http://lists.freedesktop.org/archives/dri-devel/2012-May/023426.html
http://lists.freedesktop.org/archives/dri-devel/2012-May/023467.htmlAcked-by: Matthew Garrett <mjg59@srcf.ucam.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Merge branch 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-next

Nothing terribly exciting in here probably:
- reworked thermal stuff from mupuf/I, has a chance of possibly working
well enough when we get to being able to reclock..
- driver will report mmio access faults on chipsets where it's supported
- will now sleep waiting on fences on nv84+ rather than polling
- some cleanup of the internal fencing, looking towards sli/dmabuf sync
- initial support for anx9805 dp/tmds encoder
- nv50+ display fixes related to the above, and also might fix a few
other issues
- nicer error reporting (will log process names with channel errors)
- various other random fixes

* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6: (87 commits)
  nouveau: ACPI support depends on X86 and X86_PLATFORM_DEVICES
  drm/nouveau/i2c: add support for ddc/aux, and dp link training on anx9805
  drm/nv50: initial kms support for off-chip TMDS/DP encoders
  drm/nv50-/disp: initial supervisor support for off-chip encoders
  drm/nv50-/disp: initial work towards supporting external encoders
  drm/nv50-/kms: remove unnecessary wait-for-completion points
  drm/nv50-/disp: move DP link training to core and train from supervisor
  drm/nv50-/disp: handle supervisor tasks from workqueue
  drm/nouveau/i2c: create proper chipset-specific class implementations
  drm/nv50-/disp: 0x0000 is a valid udisp config value
  drm/nv50/devinit: reverse the logic for running encoder init scripts
  drm/nouveau/bios: store a type/mask hash in parsed dcb data
  drm/nouveau/i2c: extend type to 16-bits, add lookup-by-type function
  drm/nouveau/i2c: aux channels not necessarily on nvio
  drm/nouveau/i2c: fix a bit of a thinko in nv_wri2cr helper functions
  drm/nouveau/bios: parse external transmitter type if off-chip
  drm/nouveau: store i2c port pointer directly in nouveau_encoder
  drm/nouveau/i2c: handle i2c/aux mux outside of port lookup function
  drm/nv50/graph: avoid touching 400724, it doesn't exist
  drm/nouveau: Fix DPMS 1 on G4 Snowball, from snow white to coal black.
  ...

If I build nouveau on ia64, Kconfig warns:

warning: (DRM_NOUVEAU) selects ACPI_WMI which has unmet direct dependencies (X86 && X86_PLATFORM_DEVICES && ACPI)
warning: (DRM_NOUVEAU) selects MXM_WMI which has unmet direct dependencies (X86 && X86_PLATFORM_DEVICES && ACPI_WMI)

Make all the ACPI support depend on X86 and select
X86_PLATFORM_DEVICES.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>