The lack of chained_irq_exit() leaves the muxed interrupt masked on MMP3.
For reasons unknown this is not a problem on MMP2.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20190822092643.593488-8-lkundrak@v3.sk

The "regs" property of the "mrvl,mmp2-mux-intc" devices are silly. They
are offsets from intc's base, not addresses on the parent bus. At this
point it probably can't be fixed.

On an OLPC XO-1.75 machine, the muxes are children of the intc, not the
axi bus, and thus of_address_to_resource() won't work. We should treat
the values as mere integers as opposed to bus addresses.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Link: https://lore.kernel.org/r/20190822092643.593488-7-lkundrak@v3.sk

The meson sm1 SoCs uses the same type of GPIO interrupt controller IP
block as the other meson SoCs, A total of 100 pins can be spied on:

- 223:100 undefined (no interrupt)
- 99:97   3 pins on bank GPIOE
- 96:77   20 pins on bank GPIOX
- 76:61   16 pins on bank GPIOA
- 60:53   8 pins on bank GPIOC
- 52:37   16 pins on bank BOOT
- 36:28   9 pins on bank GPIOH
- 27:12   16 pins on bank GPIOZ
- 11:0    12 pins in the AO domain

Mapping is the same as the g12a family but the sm1 controller
allows to trig an irq on both edges of the input signal. This was
not possible with the previous SoCs families
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20190829161635.25067-3-jbrunet@baylibre.com

Update the dt-binding to add support for the sm1 SoC family in the
amlogic GPIO interrupt controller driver.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20190829161635.25067-2-jbrunet@baylibre.com

We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.

// <smpl>
@@
expression ret;
struct platform_device *E;
@@

ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);

if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>

While we're here, remove braces on if statements that only have one
statement (manually).

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>

Add a header include guard just in case.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>

Using a default domain on DT platforms is unnecessary, as the firmware
tables describe the full topology, and nothing is implicit.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
[maz: wrote an actual changelog]
Signed-off-by: Marc Zyngier <maz@kernel.org>

We try to find a free LPI region in device's lpi_map and allocate them
(set them to 1) when we want to allocate LPIs for this device. This is
what bitmap_find_free_region() has done for us. The following set_bit
is redundant and a bit confusing (since we only set_bit against the first
allocated LPI idx). Remove it, and make the set_bit explicit by comment.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>

It looks like the HIP06/07 SoCs have extra bits in their GICD_TYPER
registers, which confuse the GICv3.1 code (these systems appear to
expose ESPIs while they actually don't).

Detect these systems as early as possible and wipe the fields that
should be RES0 in the register.
Tested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>

When evaluating potential quirks matched by reads of the IIDR
register, skip the quirk entries that use a "compatible"
property attached to them, as these are DT based.
Signed-off-by: Marc Zyngier <maz@kernel.org>

As is it usual for the GIC, it isn't disallowed to put together a system
that is majorly inconsistent, with a distributor supporting the
extended ranges while some of the CPUs don't.

Kindly tell the user that things are sailing isn't going to be smooth.
Signed-off-by: Marc Zyngier <maz@kernel.org>

Expand the pre-existing PPI support to be able to deal with the
Extended PPI range (EPPI). This includes obtaining the number of PPIs
from each individual redistributor, and compute the minimum set
(just in case someone builds something really clever...).
Signed-off-by: Marc Zyngier <maz@kernel.org>

Update the GICv3 binding to allow interrupts in the EPPI range.
Signed-off-by: Marc Zyngier <maz@kernel.org>

Again, PPIs are becoming a variable set. Let's hack the PPI partition
code to make the top-level array dynamically allocated.
Signed-off-by: Marc Zyngier <maz@kernel.org>

As we're about to have a variable number of PPIs, let's make the
allocation of the NMI refcounts dynamic. Also apply some minor
cleanups (moving things around).
Signed-off-by: Marc Zyngier <maz@kernel.org>

GICv3.1 allows up to 80 PPIs (16 legaci PPIs and 64 Extended PPIs),
meaning we can't just leave the old 16 hardcoded everywhere.

We also need to add the infrastructure to discover the number of PPIs
on a per redistributor basis, although we still pretend there is only
16 of them for now.

No functional change.
Signed-off-by: Marc Zyngier <maz@kernel.org>

Add the required support for the ESPI range, which behave exactly like
the SPIs of old, only with new funky INTIDs.
Signed-off-by: Marc Zyngier <maz@kernel.org>

GICv3.1 introduces support for new interrupt ranges, one of them being
the Extended SPI range (ESPI). The DT binding is extended to deal with
it as a new interrupt class.
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>

In the beginning, life was simple. The GIC driver mostly cared about
PPIs, SPIs and LPIs, all with nicely layed out ranges.

We're about to change all that, with new ranges such as EPPI and ESPI
interleaved in the middle of the no-irq-land between the "special IDs"
and the LPI range. Boo.

In order to make our life less hellish, let's introduce a set of primitives
that will allow ranges to be identified easily and offsets to be remapped.

So far, there is no functionnal change.
Signed-off-by: Marc Zyngier <maz@kernel.org>

gic_configure_irq is currently passed the (re)distributor address,
to which it applies an a fixed offset to get to the configuration
registers. This offset is constant across all GICs, or rather it was
until to v3.1...

An easy way out is for the individual drivers to pass the base
address of the configuration register for the considered interrupt.
At the same time, move part of the error handling back to the
individual drivers, as things are about to change on that front.
Signed-off-by: Marc Zyngier <maz@kernel.org>

Booting a large arm64 server (HiSi D05) leads to the following
shouting at boot time:

[   20.722132] debugfs: File 'irqchip@(____ptrval____)-3' in directory 'domains' already present!
[   20.730851] debugfs: File 'irqchip@(____ptrval____)-3' in directory 'domains' already present!
[   20.739560] debugfs: File 'irqchip@(____ptrval____)-3' in directory 'domains' already present!
[   20.748267] debugfs: File 'irqchip@(____ptrval____)-3' in directory 'domains' already present!
[   20.756975] debugfs: File 'irqchip@(____ptrval____)-3' in directory 'domains' already present!
[   20.765683] debugfs: File 'irqchip@(____ptrval____)-3' in directory 'domains' already present!
[   20.774391] debugfs: File 'irqchip@(____ptrval____)-3' in directory 'domains' already present!

and many more... Evidently, we expect something a bit more informative
than ____ptrval____, and certainly we want all of our domains, not just
the first one.

For that, turn the %p used to generate the fwnode name into something
that won't be repainted (%pa). Given that we've now fixed all users to
pass a pointer to a PA, it will actually do the right thing.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>

To allocate its fwnode that is then used to allocate an irqdomain,
the driver uses irq_domain_alloc_fwnode(), passing it a VA as an
identifier. This is a rather bad idea, as this address ends up
published in debugfs (and we want to move away from VAs there
anyway).

Instead, let's allocate a named fwnode by using the device GUID as
an identifier. It is allegedly unique, and can be traced back to
the original device.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>

Do not expose the base VA (it appears in debugfs). Instead,
record the PA, which at least can be used to precisely identify
the associated irqchip and domain.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>

Do not expose the base VA (it appears in debugfs). Instead,
record the PA, which at least can be used to precisely identify
the associated irqchip and domain.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>

Do not expose the frame's VA (it appears in debugfs). Instead,
record the PA, which at least can be used to precisely identify
the associated irqchip and domain.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>

Do not expose the distributor's VA (it appears in debugfs). Instead,
record the PA, which at least can be used to precisely identify
the associated irqchip and domain.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>

Do not expose the ITS' VA (it appears in debugfs). Instead, record
the PA, which at least can be used to precisely identify the associated
irqchip and domain.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>

Do not expose the distributor's VA (it appears in debugfs). Instead,
record the PA, which at least can be used to precisely identify
the associated irqchip and domain.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>

Pull tpm fixes from Jarkko Sakkinen:
 "Two bug fixes that did not make into my first pull request"

* tag 'tpmdd-next-20190805' of git://git.infradead.org/users/jjs/linux-tpmdd:
  tpm: tpm_ibm_vtpm: Fix unallocated banks
  tpm: Fix null pointer dereference on chip register error path

Pull MTD fixes from Miquel Raynal:
 "NAND:

   - Fix Micron driver as some chips enable internal ECC correction
     during their discovery while they advertize they do not have any.

  Hyperbus:

   - Restrict the build to only ARM64 SoCs (and compile testing) which
     is what should have been done since the beginning.

   - Fix Kconfig issue by selection something instead of implying it"

* tag 'mtd/fixes-for-5.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
  mtd: hyperbus: Add hardware dependency to AM654 driver
  mtd: hyperbus: Kconfig: Fix HBMC_AM654 dependencies
  mtd: rawnand: micron: handle on-die "ECC-off" devices correctly

The nr_allocated_banks and allocated banks are initialized as part of
tpm_chip_register. Currently, this is done as part of auto startup
function. However, some drivers, like the ibm vtpm driver, do not run
auto startup during initialization. This results in uninitialized memory
issue and causes a kernel panic during boot.

This patch moves the pcr allocation outside the auto startup function
into tpm_chip_register. This ensures that allocated banks are initialized
in any case.

Fixes: 879b5892 ("tpm: retrieve digest size of unknown algorithms with PCR read")
Reported-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Nayna Jain <nayna@linux.ibm.com>
Reviewed-by: Mimi Zohar <zohar@linux.ibm.com>
Tested-by: Sachin Sant <sachinp@linux.vnet.ibm.com>
Tested-by: Michal Suchánek <msuchanek@suse.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

If clk_enable is not defined and chip initialization
is canceled code hits null dereference.

Easily reproducible with vTPM init fail:
  swtpm chardev --tpmstate dir=nonexistent_dir --tpm2 --vtpm-proxy

BUG: kernel NULL pointer dereference, address: 00000000
...
Call Trace:
 tpm_chip_start+0x9d/0xa0 [tpm]
 tpm_chip_register+0x10/0x1a0 [tpm]
 vtpm_proxy_work+0x11/0x30 [tpm_vtpm_proxy]
 process_one_work+0x214/0x5a0
 worker_thread+0x134/0x3e0
 ? process_one_work+0x5a0/0x5a0
 kthread+0xd4/0x100
 ? process_one_work+0x5a0/0x5a0
 ? kthread_park+0x90/0x90
 ret_from_fork+0x19/0x24

Fixes: 719b7d81 ("tpm: introduce tpm_chip_start() and tpm_chip_stop()")
Cc: stable@vger.kernel.org # v5.1+
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Pull powerpc fixes from Michael Ellerman:
 "Some more powerpc fixes for 5.3:

   - Wire up the new clone3 syscall.

   - A fix for the PAPR SCM nvdimm driver, to fix a crash when firmware
     gives us a device that's attached to a non-online NUMA node.

   - A fix for a boot failure on 32-bit with KASAN enabled.

   - Three fixes for implicit fall through warnings, some of which are
     errors for us due to -Werror.

  Thanks to: Aneesh Kumar K.V, Christophe Leroy, Kees Cook, Santosh
  Sivaraj, Stephen Rothwell"

* tag 'powerpc-5.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/kasan: fix early boot failure on PPC32
  drivers/macintosh/smu.c: Mark expected switch fall-through
  powerpc/spe: Mark expected switch fall-throughs
  powerpc/nvdimm: Pick nearby online node if the device node is not online
  powerpc/kvm: Fall through switch case explicitly
  powerpc: Wire up clone3 syscall

At the end of the v5.3 upstream kernel development cycle, Simon will be
stepping down from his role as Renesas SoC maintainer.  Starting with
the v5.4 development cycle, Geert is taking over this role.

Add Geert as a co-maintainer, and add his git repository and branch.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'kbuild-fixes-v5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - detect missing missing "WITH Linux-syscall-note" for uapi headers

 - fix needless rebuild when using Clang

 - fix false-positive cc-option in Kconfig when using Clang

 - avoid including corrupted .*.cmd files in the modpost stage

 - fix warning of 'make vmlinux'

 - fix {m,n,x,g}config to not generate the broken .config on the second
   save operation.

 - some trivial Makefile fixes

* tag 'kbuild-fixes-v5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kconfig: Clear "written" flag to avoid data loss
  kbuild: Check for unknown options with cc-option usage in Kconfig and clang
  lib/raid6: fix unnecessary rebuild of vpermxor*.c
  kbuild: modpost: do not parse unnecessary rules for vmlinux modpost
  kbuild: modpost: remove unnecessary dependency for __modpost
  kbuild: modpost: handle KBUILD_EXTRA_SYMBOLS only for external modules
  kbuild: modpost: include .*.cmd files only when targets exist
  kbuild: initialize CLANG_FLAGS correctly in the top Makefile
  kbuild: detect missing "WITH Linux-syscall-note" for uapi headers

Pull SafeSetID maintainer update from Micah Morton:
 "Add entry in MAINTAINERS file for SafeSetID LSM"

* tag 'safesetid-maintainers-correction-5.3-rc2' of git://github.com/micah-morton/linux:
  Add entry in MAINTAINERS file for SafeSetID LSM

Prior to this commit, starting nconfig, xconfig or gconfig, and saving
the .config file more than once caused data loss, where a .config file
that contained only comments would be written to disk starting from the
second save operation.

This bug manifests itself because the SYMBOL_WRITTEN flag is never
cleared after the first call to conf_write, and subsequent calls to
conf_write then skip all of the configuration symbols due to the
SYMBOL_WRITTEN flag being set.

This commit resolves this issue by clearing the SYMBOL_WRITTEN flag
from all symbols before conf_write returns.

Fixes: 8e2442a5 ("kconfig: fix missing choice values in auto.conf")
Cc: linux-stable <stable@vger.kernel.org> # 4.19+
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Pull Xtensa fix from Max Filippov:
 "Fix build for xtensa cores with coprocessors that was broken by
  entry/return abstraction patch"

* tag 'xtensa-20190803' of git://github.com/jcmvbkbc/linux-xtensa:
  xtensa: fix build for cores with coprocessors

Pull i2c fixes from Wolfram Sang:
 "A set of driver fixes for the I2C subsystem"

* 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: s3c2410: Mark expected switch fall-through
  i2c: at91: fix clk_offset for sama5d2
  i2c: at91: disable TXRDY interrupt after sending data
  i2c: iproc: Fix i2c master read more than 63 bytes
  eeprom: at24: make spd world-readable again