Silences the following checkpatch warning:
WARNING: braces {} are not necessary for any arm of this statement
	if (priv->rev == 1) {
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

  When make with EXTRA_CFLAGS=-W, it will report error.
  so give a check in Makefile.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Instead of checking if num_encoders is zero, it is being assigned 0.
Convert the assignment to a check.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

commit ae128786
Author: Dave Airlie <airlied@redhat.com>
Date:   Thu Jan 24 16:12:41 2013 +1000

    fbcon: don't lose the console font across generic->chip driver switch

uses a pointer in vc->vc_font.data to load font into the new driver.
However if the font is actually freed, we need to clear the data
so that we don't reload font from dangling pointer.

Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=892340Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

Alex writes:
A few more updates for 3.10.  Nothing too major here.  Mostly bug fixes.
The big changes are adding golden register init for 7xx and newer asics
and some audio cleanups.

* 'drm-next-3.10-2' of git://people.freedesktop.org/~agd5f/linux: (32 commits)
  drm/radeon: disable UVD advanced semaphore mode
  drm/radeon: fix endian bugs in radeon_atom_get_clock_dividers() (v3)
  drm/radeon: fix up audio dto programming for DCE2
  drm/radeon/evergreen: set SAD registers
  drm: add drm_edid_to_eld helper extracting SADs from EDID (v2)
  drm/radeon/si: add support for golden register init
  drm/radeon/cayman,TN: add support for golden register init (v2)
  drm/radeon/evergreen: add support for golden register init
  drm/radeon/7xx: add support for golden register init
  drm/radeon: add helper function to support golden registers
  drm/radeon: fix typo in si_select_se_sh()
  drm/radeon: switch audio handling to use callbacks
  drm/radeon: clean up audio dto programming
  drm/radeon: clean up audio supported check
  drm/radeon: raise UVD clocks on init v3
  drm/radeon: raise UVD clocks only on demand
  drm/radeon: put UVD PLLs in bypass mode
  drm/radeon: disable audio format interrupts on Evergreen
  drm/radeon: fix hdmi mode enable on RS600/RS690/RS740
  drm/radeon/evergreen: write default channel numbers
  ...

Not needed and seems to cause some problems.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

v2: fix copy paste typo.
v3: clarify new union member
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Uses a different register than DCE3 asics.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This allows audio (alsa) driver to read them and have a clue about audio
capabilities of connected receiver. This has been verified to be
compatible with fglrx behaviour for Onkyo TX-SR605 and Denon 1912.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Some devices (ATI/AMD cards) don't support passing ELD struct to the
hardware but just require filling specific registers and then the
hardware/firmware does the rest. In such cases we need to read the info
from SAD blocks and put them in the correct registers.

agd5f: note that the returned pointer needs to be kfreed as per
Christian's suggestion.

v2: fix warning
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

v2: add richland support
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Golden registers are arrays of register settings from the
hw team that need to be initialized at asic startup.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Register audio callbacks for asic where we support
audio.  Cleans up the code and makes it easier to
add support for newer asics.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Split into DCE2/3 and DCE4/5 variants. Still todo is to
calculate the DTO dividers properly.  Add proper formula
to the comments.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

v2: not only raise the clocks on VCPU boot, but also on IB test.
v3: agd5f: fix r600_uvd_init return value.

fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=63730Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

That not only saves some power, but also solves problems with
older chips where an idle UVD block on higher clocks can
cause problems.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Just power down the PLL when we get a VCLK or DCLK of zero.
Enabling the bypass mode early should also allow us to
switch UVD clocks on the fly.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The audio format change interrupts are an aid in debugging,
but not required for operation.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

These chips were previously skipped since they are
pre-R600.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Driver fglrx setups audio and ACR packets after basic initialization,
which sounds sane, do the same.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Closed source driver fglrx seems to enable infoframes and audio packets
at the end, which makes sense, do the same.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Message and feedback buffers must be at start of
VRAM, not at start of address space.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Just disabling the mem requests should be enough, but
that doesn't seem to work correctly on efi systems.

May fix:
https://bugs.freedesktop.org/show_bug.cgi?id=57567
https://bugs.freedesktop.org/show_bug.cgi?id=43655
https://bugzilla.kernel.org/show_bug.cgi?id=56441

v2: blank displays first, then disable.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Just disabling the mem requests should be enough, but
that doesn't seem to work correctly on efi systems.

v2: blank displays first, then disable.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Need to wait for the new addresses to take affect before
re-enabling the MC.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Need to wait for the new addresses to take affect before
re-enabling the MC.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Properly wait for the next vblank region.  The previous
code didn't always wait long enough depending on the timing.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Properly wait for the next vblank region.  The previous
code didn't always wait long enough depending on the timing.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Properly wait for the next vblank region.  The previous
code didn't always wait long enough depending on the timing.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

drm/tegra: Changes for v3.10-rc1

The bulk of this pull-request is the host1x series that has been in the
works for a few months. The current implementation looks good and has
been tested by several independent parties. So far no issues have been
found. To be on the safe side, the new Tegra-specific DRM IOCTLs depend
on staging in order to give some amount of flexibility to change them
just in case. The plan is to remove that dependency once more userspace
exists to verify the adequacy of the IOCTLs.

Currently only the 2D engine is supported, but patches are in the works
to enable 3D support on top of this framework as well. Various bits of
open-source userspace exist to test the 2D and 3D support[0]. This is
still a bit immature but it allows to verify that the kernel interfaces
work properly.

To round things off there are two smaller cleanup patches, one of them
adding a new pixel format and the other removing a redundent Kconfig
dependency.

[0]: https://github.com/grate-driver

* tag 'drm/tegra/for-3.10' of git://anongit.freedesktop.org/tegra/linux:
  drm/tegra: don't depend on OF
  drm/tegra: Support the XBGR8888 pixelformat
  drm/tegra: Add gr2d device
  gpu: host1x: drm: Add memory manager and fb
  gpu: host1x: Remove second host1x driver
  gpu: host1x: drm: Rename host1x to host1x_drm
  drm/tegra: Move drm to live under host1x
  gpu: host1x: Add debug support
  gpu: host1x: Add channel support
  gpu: host1x: Add syncpoint wait and interrupts
  gpu: host1x: Add host1x driver

ARCH_TEGRA always enabled OF, so there's no need for any driver to
depend on it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>

While at it, also include the RGB565 pixelformat in the list of formats
supported by overlays.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Erik Faye-Lund <kusmabite@gmail.com>