Pad the SKB to the minimum length of ETH_ZLEN by using skb_put_padto()
and take this operation out of the critical section since there is no
need to check any HW resources before doing that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r6040_xmit() is increasing transmit statistics during transmission while
this may still fail, do this in r6040_tx() where we complete transmitted
buffers instead.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of open coding our own version utilize the library provided
function.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox 100G mlx5 ethtool ntuple steering

This series adds Ethernet ethtool ntuple steering 'ethtool -N|U' and exposes two more
counter sets to Ethtool statistics, RDMA vport and global flow control statistics.

We start from three refactoring patches of the flow steering infrastructure
    - mlx5_add_flow_rule will now receive mlx5 flow spec to simplify and reduce
      number of parameters
    - All low level steering objects are now wrapped in mlx5_flow_steering structure
      for better encapsulation
    - Flow steering object will now be removed properly and generically rather than
      traversing on a well-known steering tree objects

Patch#4 adds the infrastructure and the data structures needed for the ethtool ntuple
steering, all implemented in a new file 'en_fs_ethtool.c'.  Add the support for set_rxnfc
ethtool callback to add/remove/replace a flow spec of ethter type L2.

Patch#5 adds the support for L3/L4 flow specs and a higher priority in favor for L3/L4
rules when interleaving with L2 rules.

Patch#6 adds the support for get_rxnfc ethtool callback.

Patch#7,8 adds RDMA vport and global flow control statistics.

Applied on top: 8186f6e3 ('net-next: mediatek: fix compile error inside mtk_poll_controller()')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Just like per prio counters, the global flow counters are queried from
per priority counters register.
Global flow control counters are stored in priority 0 PFC counters.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the needed descriptors to expose RoCE RDMA counters.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enhance the existing get_rxnfc callback:
1. Get flow rule of specific ID.
2. Get all flow rules.
3. Get number of rules.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support to add flow steering rules with ethtool
of L3/L4 flow types (ip4/tcp4/udp4).
Those rules will be in higher priority than l2 flow rules, in order
to prefer more specific rules.

Mask is not supported for l3/l4 flow types.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement etrhtool set_rxnfc callback to support ethtool flow spec
direct steering. This patch adds only the support of ether flow type
spec. L3/L4 flow specs support will be added in downstream patches.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of explicitly cleaning up the well known parts of the steering
tree, we use the generic tree structure to traverse for cleanup.
No functional changes.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of having all steering private name spaces and
steering module fields flat in mlx5_core_priv, we wrap
them in mlx5_flow_steering for better modularity and
API exposure.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reduce the set of arguments passed to mlx5_add_flow_rule
by introducing flow_spec structure.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 80673029 ("net-next: mediatek: add support for IRQ grouping")
adds handling for irq 1 and 2 to the uninit function but did not remove
irq 0 which is not used since irq grouping was introduced. Fix this by
removing the superfluous call to free_irq().
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: John Crispin <john@phrozen.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit f786f356 ("net: ethernet: lpc_eth: use phydev
from struct net_device") the 'pldat' variable became unused, so
just remove it.
Reported-by: Olof's autobuilder <build@lixom.net>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Wunderlich says:

====================
This feature patchset includes the following changes:

 - Cleanup work by Markus Pargmann and Sven Eckelmann (six patches)

 - Initial Netlink support by Matthias Schiffer (two patches)

 - Throughput Meter implementation by Antonio Quartulli, a kernel-space
   traffic generator to estimate link speeds. This feature is useful on
   low-end WiFi APs where running iperf or netperf from userspace
   gives wrong results due to heavy userspace/kernelspace overhead.
   (two patches)

 - API clean-up work by Antonio Quartulli (one patch)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: Implement basic FIB offload and router interfaces

Introduce LPM trees management including virtual router management for HW.
Implement basic FIB offloading using switchdev FIB objects. For now only support
local routes and direct routes (next-hop support will be introduced in
a follow-up patchset).

Introduce router interfaces in patches 10-14.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

As with the previously introduced L3 interfaces, listen to 'inetaddr'
notifications sent for bridges devices configured on top of the port
netdevs and create / destroy router interfaces (RIFs) accordingly.
This also includes VLAN devices configured on top of the VLAN-aware
bridge.

The RIFs will be destroyed either when the last IP address is removed or
when the underlying FID is is destroyed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before introducing support for L3 interfaces on top of the VLAN-aware
bridge we need to add some missing infrastructure.

Such an interface can either be the bridge device itself or a VLAN
device on top of it. In the first case the router interface (RIF) is
associated with FID 1, which is created whenever the first port netdev
joins the bridge. We currently assume the default PVID is 1 and that
it's already created, as it seems reasonable. This can be extended in
the future.

However, in the second case it's entirely possible we've yet to create a
matching FID. This can happen if the VLAN device was configured before
making any bridge port member in the VLAN.

Prevent such ordering problems by using the VLAN device's CHANGEUPPER
event to configure the FID. Make the VLAN device hold a reference to the
FID and prevent it from being destroyed even if none of the port netdevs
is using it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previous commit deprecated the vFIDs used to get traffic to the CPU
('port_vfids'). Thus, we now use the vFIDs as god intended and the
artificial split is no longer needed.

Rename functions and variables to reflect that.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Up until now we only supported bridged interfaces. Packets ingressing
through the switch ports were either classified to FIDs (in the case of
the VLAN-aware bridge) or vFIDs (in the case of VLAN-unaware bridges).
The packets were then forwarded according to the FDB. Routing was done
entirely in slowpath, by splitting the vFID range in two and using the
lower 0.5K vFIDs as dummy bridges that simply flooded all incoming
traffic to the CPU.

Instead, allow packets to be routed in the device by creating router
interfaces (RIFs) that will direct them to the router block.
Specifically, the RIFs introduced here are Sub-port RIFs used for VLAN
devices and port netdevs. Packets ingressing from the {Port / LAG ID, VID}
with which the RIF was programmed with will be assigned to a special
kind of FIDs called rFIDs and from there directed to the router.

Create a RIF whenever the first IPv4 address was programmed on a VLAN /
LAG / port netdev. Destroy it upon removal of the last IPv4 address.
Receive these notifications by registering for the 'inetaddr'
notification chain. A non-zero (10) priority is used for the
notification block, so that RIFs will be created before routes are
offloaded via FIB code.

Note that another trigger for RIF destruction are CHANGEUPPER
notifications causing the underlying FID's reference count to go down to
zero. This can happen, for example, when a VLAN netdev with an IP address
is put under bridge. While this configuration doesn't make sense it does
cause the device and the kernel to get out of sync when the netdev is
unbridged. We intend to address this in the future, hopefully in current
cycle.

Finally, Remove the lower 0.5K vFIDs, as they are deprecated by the RIFs,
which will trap packets according to their DIP.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We are just about to introduce router interfaces (RIFs), but before that
we need to be able update the device with the correct RIF attributes
whenever they change for the netdev the RIF is backing. Two such
attributes are MTU and MAC.

The MAC is used both to set the source MAC of packets egressing from the
RIF and also to program an FDB rule that will direct packets to the
router block.

Use the existing netdevice notification block and respond to CHANGEADDR
and CHANGEMTU accordingly. Store both attributes in the RIF struct
in case we need to revert to old attributes following a failed update.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add functions that iterate over lower devices and find port device.
As a dependency add netdev_for_each_all_lower_dev and
netdev_for_each_all_lower_dev_rcu macro with
netdev_all_lower_get_next and netdev_all_lower_get_next_rcu shelpers.

Also, add functions to return mlxsw struct according to lower device
found and mlxsw_port struct with a reference to lower device.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement ipv4 FIB entries addition and removal. Initially, we support
local and broadcast routes using "ip2me" trap action.
Also, unicast routes without nexthop are supported using "local" action.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Serves for adding, updating and removing fib entries.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Virtual router is a construct used inside HW. In this implementation
we map kernel tables to virtual routers one to one. Introduce management
logic to create virtual routers when needed and destroy in case they are
no longer in use. According to that, call into LPM tree management.
Each virtual router is always bound to one LPM tree.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce basic LPM tree management allowing to share the trees in
between tables if the used prefixes in the tables are the same.
Build the tree structure according to the used prefixes. Although it is
not optimal for many use cases, this initial implementation does only
simple linear left-tree. More advanced structures will be introduced
later on, possibly including mechanisms to change trees on the fly.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This register is used to bind virtual router and protocol to an
allocated LPM tree.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Serves to build LPM tree structure.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Register serves for allocation and deallocation of LPM search tree.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shadow FIB is needed in order to hold additional information for FIB
entries and keep track of used prefixes. That is needed for the LPM tree
construction to be introduced later on in this set.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Stephen Rothwell reports a build warnings(powerpc ppc64_defconfig)

drivers/net/tun.c: In function 'tun_do_read.part.5':
/home/sfr/next/next/drivers/net/tun.c:1491:6: warning: 'err' may be
used uninitialized in this function [-Wmaybe-uninitialized]
   int err;

This is because tun_ring_recv() may return an uninitialized err, fix this.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Raghu Vatsavayi says:

====================
liquidio updates and bug fixes

Following V2 patchset contains updates and bug fixes for
liquidio driver. This patchset also has changes that you
suggested in vxlan code. Please apply the patches in following
order as some of the patches depend on earlier patches in the
series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch changes response header to be able to communicate
with new firmware interface.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes redundant file includes and conditions.
Provides some meaningful comments and code alignment.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes redudant droq num validation.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch limits the MTU  between 68 bytes and 16000 bytes.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the issue of proper freeing of queue
memory resources during free device. It also has fix for
correct pcie error reporting.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes the dependency of number of iq/oq's on
number of cpus.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch updates the delay constant for softcommands in
accrodance with new requirements.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>