Next hardware will direct TCP/UDP streams to different cores.
Packets belonging to the same stream will be directed to the same
core.
The result is that duplicates will be always directed to the same
rx queue were the first packet was received.
This enabled parallelizing the duplicate packet detection across
the different cores, without sharing data between the rx queues.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The patch below introduced a variable shadowing. Fix that.

Fixes: 3955525d ("iwlwifi: pcie: buffer packets to avoid overflowing Tx queues")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

With these ops, we can know when we are about to enter system suspend.
This allows us to exit D0i3 state before entering suspend.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Fine tune RFH registers further:
* Set default queue explicitly
* Set RFH to drop frames exceeding RB size
* Set the maximum rx transfer size to DRAM to 128 instead of 64
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

During d0i3 frames might be filtered by the FW and this may
cause reordering buffer a delay - as the frames will not be
received and reorder will time out.

Introduce an API function to receive notification of filtered
frames and pass the information to the mac80211.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When forming IBSS, mac80211 scans in order to find an already
existing cell to join.
In case the scan does not find any existing cell a new IBSS
cell is formed.
When receiving the beacons of another IBSS cell we should
merge if the other IBSS cell's TSF is higher than ours.
However, currently iwlmvm does not set any timestamp flag in
rx_status so there is no valid rx timestamp to compare the
beacon's TSF to.
The reason for that is that TSF as indicated by the firmware
is at INA time, but up till now mac80211 expected the TSF at
the beginning or end of the MPDU.
Set the flag to the newly added RX_FLAG_MACTIME_PLCP_START flag.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Current iwlwifi_trace_dev_rx prints only the cmd without the
group, which might be misleading. Change it to print the wide
id. While at it add the DATA_PATH group and sub commands to the
trace of the command names, sine it is missing due to patches
submitted in parallel.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The A-MSDU must be smaller than the Transmit FIFO in the
device. Since the size of the TXF can change depending
on the device / firmware compilation mode, take the size
of the FIFO dynamically from the what the firmware tells us.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Allow A-MSDU only when we are not downscaling and the
initial MCS is at least 5.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

in order to be able to tune the size of the desired A-MSDU
based on link condition, add a knob to modify the length
of the A-MSDU.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

If the peer allows, we can have A-MSDU inside A-MDPU.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Now that PCIe knows how to create A-MSDUs, use this
capability and prepare SKBs that are large enough to
build an A-MSDU.
Advertise TSO support towards the network stack and
segment the packet with gso_size set to be the maximal
A-MSDU length (after having taken the headers to be added
into account) to make sure that the skb that is passed
down to the transport are not longer than the maximal
A-MSDU allowed.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware handles the VHT MU-MIMO group data on its own.
However, on HW restart (and future sniffer mode) the driver
shall update the firmware on the VHT MU-MIMO group membership
status.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Incoming hardware will support VHT MU-MIMO. Declare this
capability for relevant hardware.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

A curly brace was misplaced, fix this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Working with MSIX requires prior configuration.
This includes requesting interrupt vectors from the OS,
registering the vectors and mapping the optional causes to the
relevant interrupt. In addition add new interrupt handler
to handle MSIX interrupt.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Instead of waking up the device each time we write a
register, wake it up once, and writes the registers
at once.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The driver is now ready to handle this firmware.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Klocwork is unhappy as ht_vht_rates might be accessed with
rate->index being set to values between 0 and 3 which will
lead to accessing uninitialized array elements. Effectively this
doesn't happen as in HT/VHT we're not using these rate indices.
Still fix this.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware doesn't send match found notifications when no matchsets
are passed.  This makes sense because if there are no matchsets,
nothing can be matched.  But the nl80211 API should report when there
are results available, even if no matchsets were passed.

To handle this, we can use the firmware's ITERATION_COMPLETE
reporting, which will send us notifications every time it completed a
scheduled scan iteration.  Then we can set a flag when we received
beacons and use that to report that results are available.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

These are a few fixes for the current cycle.
3 out of the 5 patches fix a bugzilla.

* fix a race that users reported when we try to load the firmware
  and the hardware rfkill interrupt triggers at the same time.
* Luca fixes a very visible bug in scheduled scan: our firmware
  doesn't support scheduled scan with no profile configured and
  the supplicant sometimes requests such scheduled scans.
* build system fix
* firmware name update for 8265
* typo fix in return value

The initialization and copying of the RSS secret key
should not use ARRAY_SIZE as we need to initialize a
dword array, and not a byte array.
Fix also the hook maximum write size to allow writing
a longer table - up to full indirection table size.

Fixes: 43413a97("iwlwifi: mvm: support rss queues configuration command")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The 9000 series uses a diffrent sized descriptor. Update the
relevant tracing field.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Register cooling device in order to have the Thermal
Manager handle the device's power budget according to the sent
notifications.
The interface adds a new thermal cooling device to
/sys/class/thermal/ folder.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Register to thermal_zone interface and implement the
thermal ops.
The thermal handles the device throttling, and sets the
the temperature thresholds the Thermal Manager would be
notified of crossing.
The thermal interface adds a new thermal zone device sensor
under /sys/class/thermal/ folder.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Up to today the driver was notified of the temperature from the FW
and decided whether to enter CT-kill or not.
From now on, the FW will decide when to enter CT-kill and will notify
the driver.
Add support for this notification.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Here's another round of updates for -next:
 * big A-MSDU RX performance improvement (avoid linearize of paged RX)
 * rfkill changes: cleanups, documentation, platform properties
 * basic PBSS support in cfg80211
 * MU-MIMO action frame processing support
 * BlockAck reordering & duplicate detection offload support
 * various cleanups & little fixes

Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Factor all assignments to rfkill_global_states[].cur into a single
function rfkill_update_global_state().
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There is still quite a bit of code using this interface, so we can't
just remove it. Hopefully it will be possible in the future, but since
its scheduled removal date is past 2 years already, we are better having
the documentation reflecting the current state of things.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The "claim" sysfs interface has been removed, so its documentation now
lives in the "removed" folder.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

No more users for it.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Pass the rfkill name and type to the device with properties
instead of driver specific platform data.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
CC: Alexandre Courbot <gnurou@gmail.com>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This prepares the driver for removal of platform data.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Helper for finding the type based on name. Useful if the
type needs to be determined based on device property.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
[modify rfkill_types array and BUILD_BUG_ON to not cause errors]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add IEEE80211_RADIOTAP_VHT entry to rtap_namespace_sizes array in order to
define alignment and size of VHT info in tx radiotap
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Today, the supplicant will add the RRM capabilities
Information Element in the association request only if
Quiet period is supported (NL80211_FEATURE_QUIET).

Quiet is one of many RRM features, and there are other RRM
features that are not related to Quiet (e.g. neighbor
report). Therefore, requiring Quiet to enable RRM is too
restrictive.
Some of the features, like neighbor report, can be
supported by user space without any help from the kernel.
Hence adding the RRM capabilities IE to association request
should be the sole user space's decision.
Removing the RRM dependency on Quiet in the driver solves
this problem, but using an old driver with a user space
tool that would not require Quiet feature would be
problematic: the user space would add NL80211_ATTR_USE_RRM
in the association request even if the kernel doesn't
advertize NL80211_FEATURE_QUIET and the association would
be denied by the kernel.

This solution adds a global RRM capability, that tells user
space that it can request RRM capabilities IE publishment
without any specific feature support in the kernel.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Drivers may need to track which vif is using VHT MU-MIMO.
Move the flag indicationg the ownership of MU_MIMO to
ieee80211_vif.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>