The GPU GX GDSC has GPU_GX_BCR reset and gfx3d_clk CXC, as stated
on downstream kernels (and as verified upstream, because otherwise
random lockups happen).
Also, add PWRSTS_RET and NO_RET_PERIPH: also as found downstream,
and also as verified here, to avoid GPU related lockups it is
necessary to force retain mem, but *not* peripheral when enabling
this GDSC (and, of course, the inverse on disablement).

With this change, the GPU finally works flawlessly on my four
different MSM8998 devices from two different manufacturers.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210114221059.483390-11-angelogioacchino.delregno@somainline.orgSigned-off-by: Stephen Boyd <sboyd@kernel.org>

In some rare occasions, we want to only set the RETAIN_MEM bit, but
not the RETAIN_PERIPH one: this is seen on at least SDM630/636/660's
GPU-GX GDSC, where unsetting and setting back the RETAIN_PERIPH bit
will generate chaos and panics during GPU suspend time (mainly, the
chaos is unaligned access).

For this reason, introduce a new NO_RET_PERIPH flag to the GDSC
driver to address this corner case.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210113183817.447866-8-angelogioacchino.delregno@somainline.orgSigned-off-by: Stephen Boyd <sboyd@kernel.org>

This GDSC enables (or cuts!) power to the Multimedia Subsystem IOMMU
(mmss smmu), which has bootloader pre-set secure contexts.
In the event of a complete power loss, the secure contexts will be
reset and the hypervisor will crash the SoC.

To prevent this, and get a working multimedia subsystem, set this
GDSC as always on.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210114221059.483390-10-angelogioacchino.delregno@somainline.orgSigned-off-by: Stephen Boyd <sboyd@kernel.org>

Hardware clock gating is supported on some of the clocks declared in
there: ignoring that it does exist may lead to unstabilities on some
firmwares.
Add the HWCG registers where applicable to stop potential crashes.

This was verified on a smartphone shipped with a recent MSM8998
firmware, which will experience random crashes without this change.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210114221059.483390-9-angelogioacchino.delregno@somainline.orgSigned-off-by: Stephen Boyd <sboyd@kernel.org>

All of the GPLLs in the MSM8998 Global Clock Controller are Fabia PLLs
and not generic alphas: this was producing bad effects over the entire
clock tree of MSM8998, where any GPLL child clock was declaring a false
clock rate, due to their parent also showing the same.

The issue resides in the calculation of the clock rate for the specific
Alpha PLL type, where Fabia has a different register layout; switching
the MSM8998 GPLLs to the correct Alpha Fabia PLL type fixes the rate
(calculation) reading. While at it, also make these PLLs fixed since
their rate is supposed to *never* be changed while the system runs, as
this would surely crash the entire SoC.

Now all the children of all the PLLs are also complying with their
specified clock table and system stability is improved.

Fixes: b5f5f525 ("clk: qcom: Add MSM8998 Global Clock Control (GCC) driver")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210114221059.483390-7-angelogioacchino.delregno@somainline.orgSigned-off-by: Stephen Boyd <sboyd@kernel.org>

The GPU IOMMU depends on this clock and the hypervisor will crash
the SoC if this clock gets disabled because the secure contexts
that have been set on this IOMMU by the bootloader will become
unaccessible (or they get reset).
Mark this clock as critical to avoid this issue when the Adreno
GPU is enabled.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210114221059.483390-6-angelogioacchino.delregno@somainline.orgSigned-off-by: Stephen Boyd <sboyd@kernel.org>

To achieve CPR-Hardened functionality this clock must be on: add it
in order to be able to get it managed by the CPR3 driver.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210114221059.483390-5-angelogioacchino.delregno@somainline.orgSigned-off-by: Stephen Boyd <sboyd@kernel.org>

Add new clock definition to gcc-msm8998 dt-bindings
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210114221059.483390-4-angelogioacchino.delregno@somainline.orgSigned-off-by: Stephen Boyd <sboyd@kernel.org>

This clock enables the GPLL0 output to the multimedia subsystem
clock controller.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210114221059.483390-3-angelogioacchino.delregno@somainline.orgSigned-off-by: Stephen Boyd <sboyd@kernel.org>

Add new clock definition to gcc-msm8998 dt-bindings.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210114221059.483390-2-angelogioacchino.delregno@somainline.orgSigned-off-by: Stephen Boyd <sboyd@kernel.org>

This commit adds a regulator supply hook to mmcx-reg missing from

- mvs0c_gdsc
- mvs1c_gdsc
- mvs0_gdsc
- mvs1_gdsc
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210204150120.1521959-5-bryan.odonoghue@linaro.orgSigned-off-by: Stephen Boyd <sboyd@kernel.org>

This patch adds the missing video_cc_mvs0_clk entry to
videocc-sm8250 replicating in upstream the explicit entry for this clock in
downstream.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210204150120.1521959-4-bryan.odonoghue@linaro.orgSigned-off-by: Stephen Boyd <sboyd@kernel.org>

This patch adds the missing video_cc_mvs0_div_clk_src entry to
videocc-sm8250 replicating in upstream the explicit entry for this clock in
downstream.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210204150120.1521959-3-bryan.odonoghue@linaro.orgSigned-off-by: Stephen Boyd <sboyd@kernel.org>

Two indexes need to be added to videocc-sm8250.h for venus to function
properly. Rather than adding the missing indexes when used we add them
separately here to keep checkpatch.pl happy.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210204150120.1521959-2-bryan.odonoghue@linaro.orgSigned-off-by: Stephen Boyd <sboyd@kernel.org>

This adds Global Clock controller (GCC) driver for SM8350 SoC
Signed-off-by: Vivek Aknurwar <viveka@codeaurora.org>
Signed-off-by: Jeevan Shriram <jshriram@codeaurora.org>
[vkoul: rebase and tidy up for upstream]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210127070811.152690-6-vkoul@kernel.orgSigned-off-by: Stephen Boyd <sboyd@kernel.org>

Add device tree bindings for global clock controller on SM8350 SoCs.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210127070811.152690-5-vkoul@kernel.orgSigned-off-by: Stephen Boyd <sboyd@kernel.org>

Lucid 5LPE is a slightly different Lucid PLL with different offsets and
porgramming sequence so add support for these
Signed-off-by: Vivek Aknurwar <viveka@codeaurora.org>
Signed-off-by: Jeevan Shriram <jshriram@codeaurora.org>
[vkoul: rebase and tidy up for upstream]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210127070811.152690-4-vkoul@kernel.orgSigned-off-by: Stephen Boyd <sboyd@kernel.org>

Trion 5LPE set rate uses code similar to alpha_pll_trion_set_rate() but
with different registers. Modularize these by moving out latch and latch
ack bits so that we can reuse the function.
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210127070811.152690-3-vkoul@kernel.orgSigned-off-by: Stephen Boyd <sboyd@kernel.org>

Driver uses regval variable for holding register values, replace with a
shorter one val
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210127070811.152690-2-vkoul@kernel.orgSigned-off-by: Stephen Boyd <sboyd@kernel.org>

Add clocks, resets and some of the GDSC provided by the global clock
controller found in the Qualcomm SC8180x platform.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210126043155.1847823-2-bjorn.andersson@linaro.org
[sboyd@kernel.org: Drop F macro as it's already defined]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

Add devicetree binding for the global clock controller found in the
Qualcomm SC8180x platform.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210126043155.1847823-1-bjorn.andersson@linaro.orgSigned-off-by: Stephen Boyd <sboyd@kernel.org>

There are intermittent GDSC power-up failures observed for titan top
gdsc, which requires the XO clock. Thus mark all the MM XO clocks always
enabled from probe.

Fixes: 8d402594 ("clk: qcom: camcc-sc7180: Use runtime PM ops instead of clk ones")
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lore.kernel.org/r/1611128871-5898-1-git-send-email-tdas@codeaurora.orgSigned-off-by: Stephen Boyd <sboyd@kernel.org>

Add clocks provides by RPMH in the Qualcomm SC8180x platform.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210120223741.1610344-2-bjorn.andersson@linaro.orgSigned-off-by: Stephen Boyd <sboyd@kernel.org>

Add Qualcomm SC8180x to the list of compatibles for the RPMHCC binding.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210120223741.1610344-1-bjorn.andersson@linaro.orgSigned-off-by: Stephen Boyd <sboyd@kernel.org>

For some reason global GFM_MASK ended up with bit 1 instead of bit 0.
Remove the global GFM_MASK and reuse mux_mask field.

Fixes: a2d8f507 ("clk: qcom: Add support to LPASS AUDIO_CC Glitch Free Mux clocks")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210119113851.18946-1-srinivas.kandagatla@linaro.orgSigned-off-by: Stephen Boyd <sboyd@kernel.org>

Add a driver for the SDX55 APCS clock controller. It is part of the APCS
hardware block, which among other things implements also a combined mux
and half integer divider functionality. The APCS clock controller has 3
parent clocks:

1. Board XO
2. Fixed rate GPLL0
3. A7 PLL

This is required for enabling CPU frequency scaling on SDX55-based
platforms.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210118041156.50016-6-manivannan.sadhasivam@linaro.org
[sboyd@kernel.org: Fix unused ret in probe by hardcoding it]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

Add support for PLL found in Qualcomm SDX55 platforms which is used to
provide clock to the Cortex A7 CPU via a mux. This PLL can provide high
frequency clock to the CPU above 1GHz as compared to the other sources
like GPLL0.

In this driver, the power domain is attached to the cpudev. This is
required for CPUFreq functionality and there seems to be no better place
to do other than this driver (no dedicated CPUFreq driver).
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210118041156.50016-5-manivannan.sadhasivam@linaro.orgSigned-off-by: Stephen Boyd <sboyd@kernel.org>

Add devicetree YAML binding for Cortex A7 PLL clock in Qualcomm
platforms like SDX55.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210118041156.50016-4-manivannan.sadhasivam@linaro.orgReviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

Since commit 36e2c742 ("fs: don't allow splice read/write without
explicit ops") we've required that file operation structures explicitly
enable splice support, rather than falling back to the default handlers.

Most /proc files use the indirect 'struct proc_ops' to describe their
file operations, and were fixed up to support splice earlier in commits
40be821d..b24c30c6, but the mountinfo files interact with the
VFS directly using their own 'struct file_operations' and got missed as
a result.

This adds the necessary support for splice to work for /proc/*/mountinfo
and friends.
Reported-by: Joan Bruguera Micó <joanbrugueram@gmail.com>
Reported-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209971
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull NTB fixes from Jon Mason:
 "Bug fix for IDT NTB and Intel NTB LTR management support"

* tag 'ntb-5.11' of git://github.com/jonmason/ntb:
  ntb: intel: add Intel NTB LTR vendor support for gen4 NTB
  ntb: idt: fix error check in ntb_hw_idt.c

Pull crypto fixes from Herbert Xu:
 "Fix a number of autobuild failures due to missing Kconfig
  dependencies"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: qat - add CRYPTO_AES to Kconfig dependencies
  crypto: keembay - Add dependency on HAS_IOMEM
  crypto: keembay - CRYPTO_DEV_KEEMBAY_OCS_AES_SM4 should depend on ARCH_KEEMBAY

Pull objtool fix from Ingo Molnar:
 "Fix a segfault that occurs when built with Clang"

* tag 'objtool-urgent-2020-12-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  objtool: Fix seg fault with Clang non-section symbols

Pull locking fixes from Ingo Molnar:
 "Misc fixes/updates:

   - Fix static keys usage in module __init sections

   - Add separate MAINTAINERS entry for static branches/calls

   - Fix lockdep splat with CONFIG_PREEMPTIRQ_EVENTS=y tracing"

* tag 'locking-urgent-2020-12-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  softirq: Avoid bad tracing / lockdep interaction
  jump_label/static_call: Add MAINTAINERS
  jump_label: Fix usage in module __init

Pull timer fixes from Ingo Molnar:
 "Update/fix two CPU sanity checks in the hotplug and the boot code, and
  fix a typo in the Kconfig help text.

  [ Context: the first two commits are the result of an ongoing
    annotation+review work of (intentional) tick_do_timer_cpu() data
    races reported by KCSAN, but the annotations aren't fully cooked
    yet ]"

* tag 'timers-urgent-2020-12-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timekeeping: Fix spelling mistake in Kconfig "fullfill" -> "fulfill"
  tick/sched: Remove bogus boot "safety" check
  tick: Remove pointless cpu valid check in hotplug code

Pull scheduler fix from Ingo Molnar:
 "Fix a context switch performance regression"

* tag 'sched-urgent-2020-12-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Optimize finish_lock_switch()

Commit c9a3c4e6 ("mfd: ab8500-debugfs: Remove extraneous curly
brace") removed a left-over curly brace that caused build failures, but
Joe Perches points out that the subsequent 'seq_putc()' should also be
removed, because the commit that caused all these problems already added
the final '\n' to the seq_printf() above it.
Reported-by: Joe Perches <joe@perches.com>
Fixes: 886c8121 ("mfd: ab8500-debugfs: Remove the racy fiddling with irq_desc")
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull PCI fixes from Bjorn Helgaas:

 - Fix a tegra enumeration regression (Rob Herring)

 - Fix a designware-host check that warned on *success*, not failure
   (Alexander Lobakin)

* tag 'pci-v5.11-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: dwc: Fix inverted condition of DMA mask setup warning
  PCI: tegra: Fix host link initialization

Clang errors:

  drivers/mfd/ab8500-debugfs.c:1526:2: error: non-void function does not return a value [-Werror,-Wreturn-type]
          }
          ^
  drivers/mfd/ab8500-debugfs.c:1528:2: error: expected identifier or '('
  return 0;
          ^
  drivers/mfd/ab8500-debugfs.c:1529:1: error: extraneous closing brace ('}')
  }
  ^
  3 errors generated.

The cleanup in ab8500_interrupts_show left a curly brace around, remove
it to fix the error.

Fixes: 886c8121 ("mfd: ab8500-debugfs: Remove the racy fiddling with irq_desc")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 660c4865 ("PCI: dwc: Set 32-bit DMA mask for MSI target address
allocation") added dma_mask_set() call to explicitly set 32-bit DMA mask
for MSI message mapping, but for now it throws a warning on ret == 0, while
dma_set_mask() returns 0 in case of success.

Fix this by inverting the condition.

[bhelgaas: join string to make it greppable]
Fixes: 660c4865 ("PCI: dwc: Set 32-bit DMA mask for MSI target address allocation")
Link: https://lore.kernel.org/r/20201222150708.67983-1-alobakin@pm.meSigned-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>