- 02 Aug, 2010 40 commits
-
-
Michael Krufky authored
The signal bit is unreliable on the DT3304 in QAM mode, so set FE_HAS_SIGNAL based on 'cr_lock' Signed-off-by:
Michael Krufky <mkrufky@kernellabs.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Jarod Wilson authored
There's a currently-unused lgdt3304 demod driver, which leaves a lot to be desired as far as functionality. The 3304 is unsurprisingly quite similar to the 3305, and empirical testing yeilds far better results and more complete functionality by merging 3304 support into the 3305 driver. (For example, the current lgdt3304 driver lacks support for signal strength, snr, ucblocks, etc., which we get w/the lgdt3305). For the moment, not dropping the lgdt3304 driver, and its still up to a given device's config setup to choose which demod driver to use, but I'd suggest dropping the 3304 driver entirely. As a follow-up to this patch, I've got another patch that adds support for the KWorld PlusTV 340U (ATSC) em2870-based tuner stick, driving its lgdt3304 demod via this lgdt3305 driver, which is what I used to successfully test this patch with both VSB_8 and QAM_256 signals. A few pieces are still a touch crude, but I think its a solid start, as well as much cleaner and more feature-complete than the existing lgdt3304 driver. Signed-off-by:
Jarod Wilson <jarod@redhat.com> Signed-off-by:
-
Jean-François Moine authored
Signed-off-by:
Jean-François Moine <moinejf@free.fr> Signed-off-by:
-
Jean-François Moine authored
This function is used when the USB video interface is checked by the subdriver. Signed-off-by:
-
Jean-François Moine authored
Signed-off-by:
-
Jean-François Moine authored
- variable / function rename - set the gains in one exchange - don't alter the register 80 which contains the AWB flag and other sensor specific values - the global gain is now the average of the R, G and B gains. Signed-off-by:
-
Jean-François Moine authored
Signed-off-by:
-
Jean-François Moine authored
This patch also renames the last polling message from the closer one of the ms-windows driver. Signed-off-by:
-
Jean-François Moine authored
The new table is sorted and extracted from a clear part of the MS-Windows driver. Signed-off-by:
-
Jean-François Moine authored
Signed-off-by:
-
Jean-François Moine authored
Signed-off-by:
-
Jean-François Moine authored
This patch also changes a bit the contrast control. Signed-off-by:
-
Jean-François Moine authored
These registers seem to act on the JPEG compression whose control is not implemented in the current driver. Signed-off-by:
-
Jean-François Moine authored
Signed-off-by:
-
Jean-François Moine authored
Signed-off-by:
-
Jean-François Moine authored
The JPEG header is now included in the subdriver structure instead of being allocated and freed at capture start and stop. Signed-off-by:
-
Hans de Goede authored
setcolors(0 is a no-op for 7670 sensors, so we should not report a saturation control for 7670 sensors. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Hans de Goede authored
What we've called brightness so far actually is an exposure control, rename it and fixup the maximum and default values. Signed-off-by:
-
Hans de Goede authored
gspca_tv8532: add gain control Signed-off-by:
-
Hans de Goede authored
There is a problem with certain tv8532 cams, where sometimes there hsync/vsync locks one pixel of where it normally locks. While trying to fix this (which I failed to do). I noticed there are lots if duplicate register writes and unnecessary register reads in the tv8532 driver. This patch cleanes these ups (which has no negative effects, but unfortunately also does not help). Signed-off-by:
-
Hans de Goede authored
With the ovfx2 bridge sometimes the first few frames in a stream would be no good, as the bridge and sensor are not in complete hsync / vsync yet. This can easily be detected by checking the framesize. So if the framesize is short and it is one of the 1ste 3 frames after an sd_start, drop it. Signed-off-by:
-
Mauro Carvalho Chehab authored
Partially revert changeset 0208bef609242a2d50b95edc713a41566cae500b: As pointed by Stefan Ringel <stefan.ringel@arcor.de>, many packets become damaged by this change. That means that the "size" field of Video/VBI is not presenting 180 bytes, as it should be expected. Thanks-to: Stefan Ringel <stefan.ringel@arcor.de> Signed-off-by: -
Mauro Carvalho Chehab authored
Signed-off-by: -
Mauro Carvalho Chehab authored
Signed-off-by: -
Mauro Carvalho Chehab authored
Signed-off-by: -
Mauro Carvalho Chehab authored
Signed-off-by: -
Mauro Carvalho Chehab authored
Implements the fillbuf callback to store data received via URB data transfers. Signed-off-by: -
Mauro Carvalho Chehab authored
There are several missing things at the driver, preventing, for example, the code to start/stop DMA to actually work. Fix them before implementing a routine to store data at the audio buffers. Signed-off-by: -
Mauro Carvalho Chehab authored
Reported by Stefan Ringel. Thanks-to: Stefan Ringel <stefan.ringel@arcor.de> Signed-off-by: -
Mauro Carvalho Chehab authored
Implements a callback to be used by tm6000-alsa, in order to allow filling audio data packets. Signed-off-by: -
Mauro Carvalho Chehab authored
In order to better document and be sure that the values are used at the proper places, convert extension type into an enum and name it as "type", instead of "id". Signed-off-by: -
Mauro Carvalho Chehab authored
Signed-off-by: -
Mauro Carvalho Chehab authored
Signed-off-by:
-
