- Shorten include paths to machine specific headers.
- Remove fill_inbuf, not defined here.
- Return __dest as value from memcpy.
- Enable serial port hardware transmitter and receiver in serial_setup.
- Correct baudrate divisor calculation, changed from 4800 to 115200.
- Add support for Artpec-3 specific serial port setup.
- Initialize pinmux for the correct serial port.

- Fixes for NAND and NOR flash booting.
- Use assembler macros for common tasks (clocks, general io etc)
- Use (EtraxFS or Artpec-3) machine specific include for dram and hardware init.

Also add board_mmcspi to build if ETRAX_SPI_MMC_BOARD is set.
(Generic MMC SPI implementation)

- Remove old specific targets, use more generic ones instead.
- Use if_changed to avoid creating new images when no change.
- Use EXTRA_CFLAGS instead of CFLAGS.

- Remove old specific targets, use more generic ones instead.
- Use if_changed to avoid creating new images when no change.
- Use KBUILD_CFLAGS instead of CFLAGS.

- Remove old specific targets, use more generic ones instead.
- Use if_changed to avoid creating new images when no change.

- Remove raw_prink hack, use oops_in_progress instead.
- When ETRAX_WATCHDOG_NICE_DOGGY is set, loop in trap after oops dump
  instead of rebooting.
- Break long lines to less than 80 chars.
- Fix whitespace errors.
- Remove unnecessary comments.

- Add config to use mtd0 as whole flash device.
- Fix whitespace errors.
- Remove braces around single statement ifs.
- Break long lines.
- Remove unnecessary CVS log.

- Correct whitespace problems.
- Add ifdef for ETRAX_AXISFLASHMAP to avoid compile error when not set.

- Remove old specific targets, use more generic ones instead.
- Use if_changed to avoid creating new images when no change.
  Removes a lot of cruft.
- Use EXTRA_CFLAGS instead of CFLAGS.

- Remove old specific targets, use more generic ones instead.
- Use if_changed to avoid creating new images when no change.
- Use EXTRA_CFLAGS instead of CFLAGS.

- Remove old specific targets, use more generic ones instead.

- Remove old and non-generic targets, use generic ones instead.
- Add sub-arch as mach-fs or mach-a3 for EtraxFS and Artpec-3 respectively.
- Add links to sub-arch directories, and erase before trying to create them.
- Include from sub-arch specific include directory "mach".
- Add files to be cleaned in CLEAN_FILES instead of as archclean target.

- Use default partition table when no partition is found (for initial tests)
- Add config ETRAX_AXISFLASHMAP_MTD0WHOLE to allow whole flash as mtd0.
- Add config for VCS simulator connection.

- Add i2c_write and i2c_read as functions.
- Use spinlocks for critical regions.
- Add config item to set I2C data and clock port.
- Put unneeded testcode inside #if 0.
- Remove CVS id tag.

- Remove CRISv32 common arbiter, dma, io and pinmux files,
  they are now defined in machine dependent directories.
- Add cache and cacheflush files for working around cache problems
  in CRISv32 chips.

- Remove oldset parameter.
- Utilise delay-slot for parameter moving.
- Add kernel_execve as break 13.
- Add new kernel syscalls.

- Collect extern declarations at top of file.
- Change raw_printk to printk, use oops_in_progress instead.
- Fix formatting and whitespace.
- Allow the watchdog to be disabled during oops.

- Only disallow oops if we're in_interrupt context (was in_atomic before)
- Use the generic oops_in_progress instead of the raw_printk hack.
- Fix whitespace/formatting.
- Remove CVS log entries.

We need these to work around some cache bugs in CRISv32 chips.

- Correct include to use <>
- Rework calculation of number of IRQs and exceptions we have.
- Remove useless "mask" argument to BUILD_IRQ macro

- Add partition table struct to be used to parse partition table in flash.
- Add JFFS2 as a type, and add readoly flag.
- Improve some comments.
- Lindent has been run, fixing whitespace and formatting issues.

Now uses a DMA descriptor ring, which should avoid any unnecessary
pauses in the streams.

The header files describe the hardware registers available in both
these chips, note that most of this documentation is automatically
generated from the hardware implementation.

The two chips are somewhat different, and needs different handling.
Adds handing of the dma, dram initialization, hardware settings, io,
memory arbiter and pinmux

Also moves the dma, dram initialization and io from CRIS v32 common files.

Adds gpio and nandflash handling for Etrax-FS

Adds gpio and nandflash handling for Artpec-3.

- Remove some unneeded configs and add some new ones.
- Merge common config items to common file instead of duplicating them.
- Pull in standard Kconfig.preempt.
- Remove some unneeded Kconfigs for subsystems not (yet) available on CRIS
  (md, scsi, ieee1394, i2o, isdn, telephony, media, pcmcia, pci)
- Rename CRISv32 config items which had different types from CRISv10.
  (ETRAX_LED2G, ETRAX_LED2R, ETRAX_LED3G, ETRAX_LED3R, ETRAX_I2C_DATA_PORT,
  ETRAX_I2C_CLK_PORT)

* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm: (44 commits)
  dm raid1: report fault status
  dm raid1: handle read failures
  dm raid1: fix EIO after log failure
  dm raid1: handle recovery failures
  dm raid1: handle write failures
  dm snapshot: combine consecutive exceptions in memory
  dm: stripe enhanced status return
  dm: stripe trigger event on failure
  dm log: auto load modules
  dm: move deferred bio flushing to workqueue
  dm crypt: use async crypto
  dm crypt: prepare async callback fn
  dm crypt: add completion for async
  dm crypt: add async request mempool
  dm crypt: extract scatterlist processing
  dm crypt: tidy io ref counting
  dm crypt: introduce crypt_write_io_loop
  dm crypt: abstract crypt_write_done
  dm crypt: store sector mapping in dm_crypt_io
  dm crypt: move queue functions
  ...

* 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6: (59 commits)
  hwmon: (lm80) Add individual alarm files
  hwmon: (lm80) De-macro the sysfs callbacks
  hwmon: (lm80) Various cleanups
  hwmon: (w83627hf) Refactor beep enable handling
  hwmon: (w83627hf) Add individual alarm and beep files
  hwmon: (w83627hf) Enable VBAT monitoring
  hwmon: (w83627ehf) The W83627DHG has 8 VID pins
  hwmon: (asb100) Add individual alarm files
  hwmon: (asb100) De-macro the sysfs callbacks
  hwmon: (asb100) Various cleanups
  hwmon: VRM is not written to registers
  hwmon: (dme1737) fix Super-IO device ID override
  hwmon: (dme1737) fix divide-by-0
  hwmon: (abituguru3) Add AUX4 fan input for Abit IP35 Pro
  hwmon: Add support for Texas Instruments/Burr-Brown ADS7828
  hwmon: (adm9240) Add individual alarm files
  hwmon: (lm77) Add individual alarm files
  hwmon: Discard useless I2C driver IDs
  hwmon: (lm85) Make the pwmN_enable files writable
  hwmon: (lm85) Return standard values in pwmN_enable
  ...

* 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6: (62 commits)
  [XFS] add __init/__exit mark to specific init/cleanup functions
  [XFS] Fix oops in xfs_file_readdir()
  [XFS] kill xfs_root
  [XFS] keep i_nlink updated and use proper accessors
  [XFS] stop updating inode->i_blocks
  [XFS] Make xfs_ail_check check less by default
  [XFS] Move AIL pushing into it's own thread
  [XFS] use generic_permission
  [XFS] stop re-checking permissions in xfs_swapext
  [XFS] clean up xfs_swapext
  [XFS] remove permission check from xfs_change_file_space
  [XFS] prevent panic during log recovery due to bogus op_hdr length
  [XFS] Cleanup various fid related bits:
  [XFS] Fix xfs_lowbit64
  [XFS] Remove CFORK macros and use code directly in IFORK and DFORK macros.
  [XFS] kill superflous buffer locking (2nd attempt)
  [XFS] Use kernel-supplied "roundup_pow_of_two" for simplicity
  [XFS] Remove the BPCSHIFT and NB* based macros from XFS.
  [XFS] Remove bogus assert
  [XFS] optimize XFS_IS_REALTIME_INODE w/o realtime config
  ...

Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Douglas Gilbert <dougg@torque.net>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'slub-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/christoph/vm:
  SLUB: fix checkpatch warnings
  Use non atomic unlock
  SLUB: Support for performance statistics
  SLUB: Alternate fast paths using cmpxchg_local
  SLUB: Use unique end pointer for each slab page.
  SLUB: Deal with annoying gcc warning on kfree()

This patch adds extra information to the mirror status output, so that
it can be determined which device(s) have failed.  For each mirror device,
a character is printed indicating the most severe error encountered.  The
characters are:
 *    A => Alive - No failures
 *    D => Dead - A write failure occurred leaving mirror out-of-sync
 *    S => Sync - A sychronization failure occurred, mirror out-of-sync
 *    R => Read - A read failure occurred, mirror data unaffected
This allows userspace to properly reconfigure the mirror set.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>