- 04 Nov, 2020 8 commits
-
-
Sreekanth Reddy authored
During host reset there is a chance that the Port number allocated by the firmware for the attached devices may change. Also, it may be possible that some HBA phy's can go down/come up after reset. As a result, the driver can't just trust the HBA Port table that it has populated before host reset as valid. Instead it has to update the HBA Port table in such a way that it shouldn't disturb the drives which are still accessible even after host reset. Use the following algorithm to update the HBA Port table during host reset: I. After host reset operation and before marking the devices as responding/non-responding, create a temporary Port table called "New Port table" by parsing each of the HBA phy's Phy data info read from SAS IOUnit Page0: a. Check whether Phy's negotiated link rate is greater than 1.5Gbps, if not go to next Phy; b. Get the SAS Address of the attached device; c. Create a new entry in the "New Port table" with SAS Address field filled with attached device's SAS Address, port number with Phy's Port number (read from SAS IOUnit Page0) and enable bit in the 'Phy mask' field corresponding to current Phy number. New entry is created only if the driver can't find an entry in the "New Port table" which matches with attached device 'SAS Address' & 'Port Number'. If it finds an entry with matches with attached device 'SAS Address' & 'Port Number' then the driver takes that matched entry and will enable current Phy number bit in the 'Phy mask' field; d. After parsing all the HBA phy's info, the driver will have complete Port table info in "New Port table". II. Mark all the existing sas_device & sas_expander device structures as 'dirty'. III. Mark each entry of the HBA Port lists as 'dirty'. IV. Take each entry from 'New Port table' one by one and check whether the entry has any corresponding matched entry (which is marked as 'dirty') in the HBA Port table or not. While looking for a corresponding matched entry, look for matched entry in the sequence from top row to bottom row listed in the following table. If you find any matched entry (according to any of the rules tabulated below) then perform the action mentioned in the 'Action' column in that matched rule. =========================================================================== |Search |SAS | Phy Mask | Port | Possibilities| Action | |every |Address | or | Number | | required | |entry |matched?| subset of| matched?| | | |in below| | phy mask | | | | |sequence| | matched? | | | | =========================================================================== | 1 |matched | matched | matched | nothing |* unmark HBA port | | | | | | changed |table entry as | | | | | | |dirty | --------------------------------------------------------------------------- | 2 |matched | matched | not | port number |* Update port | | | | | matched | is changed |number in the | | | | | | |matched port table | | | | | | |entry | | | | | | |* unmask HBA port | | | | | | |table entry as | | | | | | |dirty | --------------------------------------------------------------------------- | 3.a |matched | subset of| matched |some phys |* Add these new | | | | phy mask | (or) |might have |phys to current | | | | matched | not |enabled which |port in STL | | | | | matched |are previously|* Update phy mask | | | | | (but |disabled |field in HBA's port| | | | | first | |table's matched | | | | | look for| |entry, | | | | | matched | |* Update port | | | | | one) | |number in the | | | | | | |matched port | | | | | | |table entry (if | | | | | | |port number is | | | | | | |changed), | | | | | | |* Unmask HBA port | | | | | | |table entry as | | | | | | |dirty | --------------------------------------------------------------------------- | 3.b |matched | subset of| matched |some phys |*Remove these phys | | | | phy mask | (or) |might have |from current port | | | | matched | not |disabled which|in STL | | | | | matched |are previously|* Update phy mask | | | | | (but |enabled |field in HBA's port| | | | | first | |tables's matched | | | | | look for| |entry, | | | | | matched | |*Update port number| | | | | one) | |in the matched port| | | | | | |table entry (if | | | | | | |port number is | | | | | | |changed), | | | | | | |* Unmask HBA port | | | | | | |table entry as | | | | | | |dirty | --------------------------------------------------------------------------- | 4 |matched | not | matched |A cable |*Remove old phys & | | | | matched | (or) |attached to an|new phys to current| | | | | not |expander is |port in STL | | | | | matched |changed to |* Update phy mask | | | | | |another HBA |field in HBA's port| | | | | |port during |tables's matched | | | | | |reset |entry, | | | | | | |*Update port number| | | | | | |in the matched port| | | | | | |table entry (if | | | | | | |port number is | | | | | | |changed), | | | | | | |* Unmask HBA port | | | | | | |table entry as | | | | | | |dirty | --------------------------------------------------------------------------- V. Delete the hba_port objects which are still marked as dirty. Link: https://lore.kernel.org/r/20201027130847.9962-9-sreekanth.reddy@broadcom.comReported-by:kernel test robot <lkp@intel.com> Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com>
-
Sreekanth Reddy authored
In the following scsi_host_template and sas_function_template callback functions the driver does not have PhysicalPort number information to retrieve the sas_device object using SAS Address & PhysicalPort number. In these callback functions the device's rphy object is used to retrieve sas_device object for the device. .target_alloc, .get_enclosure_identifier .get_bay_identifier When a rphy (of type sas_rphy) object is allocated then its address is saved in corresponding sas_device object's rphy field. In __mpt3sas_get_sdev_by_rphy(), the driver loops over all the sas_device objects from sas_device_list list to retrieve the sas_device objects whose rphy matches the provided rphy. Link: https://lore.kernel.org/r/20201027130847.9962-8-sreekanth.reddy@broadcom.comSigned-off-by:
-
Sreekanth Reddy authored
Renamed _transport_add_phy_to_an_existing_port() to mpt3sas_transport_add_phy_to_an_existing_port() and _transport_del_phy_from_an_existing_port() to mpt3sas_transport_del_phy_from_an_existing_port() as the driver needs to call these functions from outside mpt3sas_transport.c file. Added extra function argument 'port' of type struct hba_port to above functions and check for portID before adding/removing the phy from the _sas_port object. I.e. add/remove the phy from _sas_port object only if _sas_port's port object and phy's port object are the same. Link: https://lore.kernel.org/r/20201027130847.9962-7-sreekanth.reddy@broadcom.comSigned-off-by:
-
Sreekanth Reddy authored
Currently driver retrieves the sas_device/sas_expander objects from corresponding object's lists using just device's SAS Address. Make driver retrieve the objects from the corresponding objects list using device's SAS Address and PhysicalPort (or PortID) number. PhysicalPort number is the port number of the HBA through which this device is accessed. Link: https://lore.kernel.org/r/20201027130847.9962-6-sreekanth.reddy@broadcom.comSigned-off-by:
-
Sreekanth Reddy authored
Update hba_port's sas_address & phy_mask fields whenever a direct expander or sas/sata target devices are added or removed. When any direct attached device is discovered then driver: - Gets the hba_port object corresponding to device's PhysicalPort number; - Updates the hba_port's sas_address field with device's SAS Address; - Updates the hba_port's phy_mask filed with device's narrow/wide port Phy number bits; - If a sas/sata end device (not only direct-attached devices) is added then corresponding sas_device object's port variable is assigned with hba_port object's address whose port_id matches the device's PhysicalPort number. - If an expander device is added then corresponding sas_expander object's port variable is assigned with hba_port object's address whose port_id matches the expander device's PhysicalPort number. When any direct attached device is detached then driver will delete the hba_port object corresponding to device's PhysicalPort number. Whenever any HBA phy's link (of direct attached device's port) comes up then update the phy_mask field of corresponding hba_port object. Link: https://lore.kernel.org/r/20201027130847.9962-5-sreekanth.reddy@broadcom.comSigned-off-by:
-
Sreekanth Reddy authored
Rearrange _scsih_mark_responding_sas_device function. No functional change. Link: https://lore.kernel.org/r/20201027130847.9962-4-sreekanth.reddy@broadcom.comSigned-off-by:
-
Sreekanth Reddy authored
Allocate hba_port object whenever a new HBA's wide/narrow port is identified while processing the SASIOUnitPage0's phy data and add this object to port_table_list. Deallocate these objects during driver unload. Link: https://lore.kernel.org/r/20201027130847.9962-3-sreekanth.reddy@broadcom.comSigned-off-by:
-
Sreekanth Reddy authored
Define a new hba_port structure which holds the following variables: - port_id: Port ID of the narrow/wide port of the HBA - sas_address: SAS Address of the remote device that is attached to the current HBA port - phy_mask: HBA's phy bits to which above SAS addressed device is attached - flags: This field is used to refresh port details during HBA reset Link: https://lore.kernel.org/r/20201027130847.9962-2-sreekanth.reddy@broadcom.comSigned-off-by:
-
- 30 Oct, 2020 12 commits
-
-
Julian Wiedmann authored
As recovery for a lost Version Change event, trigger an Exchange Config Data cmd to retrieve the current FW version. Doing so requires process context (as eg. zfcp_qdio_sbal_get() might need to sleep), so defer from tasklet context into a work item. Link: https://lore.kernel.org/r/297c7be2944c3714863fcd22d531d910312d29f0.1603908167.git.bblock@linux.ibm.comSuggested-by:
Steffen Maier <maier@linux.ibm.com> Reviewed-by:
Benjamin Block <bblock@linux.ibm.com> Signed-off-by:
Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by:
-
Julian Wiedmann authored
Handle notifications for a concurrent change of the FCP Channel firmware. Update the relevant user-visible fields to provide accurate data. Link: https://lore.kernel.org/r/d2c7bc57c6cf1b65eabbf7a5d0e3927b9f65647f.1603908167.git.bblock@linux.ibm.comReviewed-by:
-
Julian Wiedmann authored
Explain why the plain spin_lock() suffices in current code, even when the stat_lock is also used by zfcp_qdio_int_req() in tasklet context. We could also promote the spin_lock() to a spin_lock_irqsave(), but that would just obfuscate the locking even further. Link: https://lore.kernel.org/r/b023b1472630f4bf9fce580577d7bb49de89ccbf.1603908167.git.bblock@linux.ibm.comReviewed-by:
-
Vasily Gorbik authored
drivers/s390/scsi/zfcp_ext.h: zfcp_sg_free_table - only declaration left after commit 58f3ead5 ("scsi: zfcp: move SG table helper from aux to fc and make them static") drivers/s390/scsi/zfcp_ext.h: zfcp_sg_setup_table - only declaration left after commit 58f3ead5 ("scsi: zfcp: move SG table helper from aux to fc and make them static") Link: https://lore.kernel.org/r/6854ae03c5c65805f746774eeb0f2869fcd6c397.1603908167.git.bblock@linux.ibm.comReviewed-by:
Vasily Gorbik <gor@linux.ibm.com> Signed-off-by:
-
Julian Wiedmann authored
Shift the IRQ tasklet processing from the qdio layer into zfcp. This will allow for a good amount of cleanups in qdio, and provides future opportunity to improve the IRQ processing inside zfcp. We continue to use the qdio layer's internal tasklet/timer mechanism (ie. scan_threshold etc) to check for Request Queue completions. Initially we planned to check for such completions after inspecting the Response Queue - this should typically work, but there's a theoretical race where the device only presents the Request Queue completions _after_ all Response Queue processing has finished. If the Request Queue is then also _completely_ full, we could send no further IOs and thus get no interrupt that would trigger an inspection of the Request Queue. So for now stick to the old model, where we can trust that such a race would be recovered by qdio's internal timer. Code-flow wise, this establishes two levels of control: 1. The qdio layer will only deliver IRQs to the device driver if the QDIO_IRQ_DISABLED flag is cleared. zfcp manages this through qdio_start_irq() / qdio_stop_irq(). The initial state is DISABLED, and zfcp_qdio_open() schedules zfcp's IRQ tasklet once during startup to explicitly enable IRQ delivery. 2. The zfcp tasklet is initialized with tasklet_disable(), and only gets enabled once we open the qdio device. When closing the qdio device, we must disable the tasklet _before_ disabling IRQ delivery (otherwise a concurrently running tasklet could re-enable IRQ delivery after we disabled it). A final tasklet_kill() during teardown ensures that no lingering tasklet_schedule() is still accessing the tasklet structure. Link: https://lore.kernel.org/r/94a765211c48b74a7b91c5e60b158de01db98d43.1603908167.git.bblock@linux.ibm.comReviewed-by:
-
ching Huang authored
Ensure getting a free ccb is done under the spin_lock. Link: https://lore.kernel.org/r/f3ec374cada762149911ff35e92a68a15a7d0327.camel@areca.com.twSigned-off-by:
ching Huang <ching2048@areca.com.tw> Signed-off-by:
-
ching Huang authored
Allow configuring the default command timeout value for devices attached to arcmsr controllers. Link: https://lore.kernel.org/r/27c0cda7fd103f05021adaf67490e9298ed5cc3f.camel@areca.com.twSigned-off-by:
-
Asutosh Das authored
Enabling this capability to let HBA power-collapse more often to save power. Link: https://lore.kernel.org/r/1306284ab2215425ca0a3d9c802574cbd6d35ea7.1603825776.git.asutoshd@codeaurora.orgReviewed-by:
Can Guo <cang@codeaurora.org> Reviewed-by:
Avri Altman <avri.altman@wdc.com> Signed-off-by:
Asutosh Das <asutoshd@codeaurora.org> Signed-off-by:
-
Can Guo authored
During clock gating, after clocks are disabled, put HBA into LPM to save more power. Link: https://lore.kernel.org/r/52198e70bff750632740d78678a815256d697e43.1603825776.git.asutoshd@codeaurora.orgReviewed-by:
Stanley Chu <stanley.chu@mediatek.com> Signed-off-by:
-
Arnd Bergmann authored
gcc -Wextra points out an assignment between two different enum types: drivers/scsi/libfc/fc_exch.c: In function 'fc_exch_setup_hdr': ../drivers/scsi/libfc/fc_exch.c:275:26: warning: implicit conversion from 'enum fc_class' to 'enum fc_sof' [-Wenum-conversion] This seems to be intentional, as the same numeric values are used here, so shut up the warning by adding an explicit cast. Link: https://lore.kernel.org/r/20201026214911.3892701-1-arnd@kernel.org Fixes: 42e9a92f ("[SCSI] libfc: A modular Fibre Channel library") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Arnd Bergmann authored
Building libfc with gcc -Warray-bounds identifies a number of cases in one file where a strncpy() is performed into a single-byte character array: In file included from include/linux/bitmap.h:9, from include/linux/cpumask.h:12, from include/linux/smp.h:13, from include/linux/lockdep.h:14, from include/linux/spinlock.h:59, from include/linux/debugobjects.h:6, from include/linux/timer.h:8, from include/scsi/libfc.h:11, from drivers/scsi/libfc/fc_elsct.c:17: In function 'strncpy', inlined from 'fc_ct_ms_fill.constprop' at drivers/scsi/libfc/fc_encode.h:235:3: include/linux/string.h:290:30: warning: '__builtin_strncpy' offset [56, 135] from the object at 'pp' is out of the bounds of referenced subobject 'value' with type '__u8[1]' {aka 'unsigned char[1]'} at offset 56 [-Warray-bounds] 290 | #define __underlying_strncpy __builtin_strncpy | ^ include/linux/string.h:300:9: note: in expansion of macro '__underlying_strncpy' 300 | return __underlying_strncpy(p, q, size); | ^~~~~~~~~~~~~~~~~~~~ This is not a bug because the 1-byte array is used as an odd way to express a variable-length data field here. I tried to convert it to a flexible-array member, but in the end could not figure out why the sizeof(struct fc_fdmi_???) are used the way they are, and how to properly convert those. Work around this instead by abstracting the string copy in a slightly higher-level function fc_ct_hdr_fill() helper that strscpy() and memset() to achieve the same result as strncpy() but does not require a zero-terminated input and does not get checked for the array overflow because gcc (so far) does not understand the behavior of strscpy(). Link: https://lore.kernel.org/r/20201026160705.3706396-2-arnd@kernel.orgSigned-off-by: -
Arnd Bergmann authored
Most of this file is only used inside of libfc, so move it to where it is actually used, with only fc_fill_fc_hdr() left inside of the header. Link: https://lore.kernel.org/r/20201026160705.3706396-1-arnd@kernel.orgReported-by:
-
- 27 Oct, 2020 10 commits
-
-
Mauro Carvalho Chehab authored
Some identifiers have different names between their prototypes and the kernel-doc markup. [mkp: fix whitespace] Link: https://lore.kernel.org/r/8ed7f149f25a363eea76e514c253c4e337c59379.1603469755.git.mchehab+huawei@kernel.orgSigned-off-by:
Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by:
-
James Smart authored
Update lpfc version to 12.8.0.5 Link: https://lore.kernel.org/r/20201020202719.54726-10-james.smart@broadcom.comCo-developed-by:
Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by:
James Smart <james.smart@broadcom.com> Signed-off-by:
-
James Smart authored
Now that MIB support was registered with FDMI, the driver may receive CT requests for MIB-related commands. At this time, no command is supported. However, the driver needs to be graceful and reject the CT request. This patch adds identification of the requests as well as sending the reject response. Link: https://lore.kernel.org/r/20201020202719.54726-9-james.smart@broadcom.comCo-developed-by:
-
James Smart authored
Created new attribute lpfc_enable_mi, which by default is enabled. Add command definition bits for SLI-4 parameters that recognize whether the adapter has MIB information support and what revision of MIB data. Using the adapter information, register vendor-specific MIB support with FDMI. The registration will be done every link up. During FDMI registration, encountered a couple of errors when reverting to FDMI rev1. Code needed to exist once reverting. Fixed these. Link: https://lore.kernel.org/r/20201020202719.54726-8-james.smart@broadcom.comCo-developed-by:
-
James Smart authored
The driver supports arbitrarily large scatter-gather lists and the current value for max_sectors is limiting. Change max_sectors to the largest value. This was actually done prior but it only corrected one template and that template was later removed. So change the remaining 2 templates. Other areas which hard-set the sectors value should be inheriting what is in the template. Link: https://lore.kernel.org/r/20201020202719.54726-7-james.smart@broadcom.comSigned-off-by:
-
James Smart authored
During code reviews duplicate code sections were found to determine the WQ Create version. The duplication was potentially overriding logic that validated page size. Link: https://lore.kernel.org/r/20201020202719.54726-6-james.smart@broadcom.comSigned-off-by:
-
James Smart authored
Removed unused MRQ-related defines that are not referenced. Link: https://lore.kernel.org/r/20201020202719.54726-5-james.smart@broadcom.comSigned-off-by:
-
James Smart authored
Commit 9816ef6e ("scsi: lpfc: Use after free in lpfc_rq_buf_free()") was made to correct a use after free condition in lpfc_rq_buf_free(). Unfortunately, a subsequent patch cut on a tree without the fix inadvertently reverted the fix. Put the fix back: Move the freeing of the rqb_entry to after the print function that references it. Link: https://lore.kernel.org/r/20201020202719.54726-4-james.smart@broadcom.com Fixes: 411de511 ("scsi: lpfc: Fix RQ empty firmware trap") Cc: <stable@vger.kernel.org> # v4.17+ Signed-off-by:
-
James Smart authored
The following call trace was seen during HBA reset testing: BUG: scheduling while atomic: swapper/2/0/0x10000100 ... Call Trace: dump_stack+0x19/0x1b __schedule_bug+0x64/0x72 __schedule+0x782/0x840 __cond_resched+0x26/0x30 _cond_resched+0x3a/0x50 mempool_alloc+0xa0/0x170 lpfc_unreg_rpi+0x151/0x630 [lpfc] lpfc_sli_abts_recover_port+0x171/0x190 [lpfc] lpfc_sli4_abts_err_handler+0xb2/0x1f0 [lpfc] lpfc_sli4_io_xri_aborted+0x256/0x300 [lpfc] lpfc_sli4_sp_handle_abort_xri_wcqe.isra.51+0xa3/0x190 [lpfc] lpfc_sli4_fp_handle_cqe+0x89/0x4d0 [lpfc] __lpfc_sli4_process_cq+0xdb/0x2e0 [lpfc] __lpfc_sli4_hba_process_cq+0x41/0x100 [lpfc] lpfc_cq_poll_hdler+0x1a/0x30 [lpfc] irq_poll_softirq+0xc7/0x100 __do_softirq+0xf5/0x280 call_softirq+0x1c/0x30 do_softirq+0x65/0xa0 irq_exit+0x105/0x110 do_IRQ+0x56/0xf0 common_interrupt+0x16a/0x16a With the conversion to blk_io_poll for better interrupt latency in normal cases, it introduced this code path, executed when I/O aborts or logouts are seen, which attempts to allocate memory for a mailbox command to be issued. The allocation is GFP_KERNEL, thus it could attempt to sleep. Fix by creating a work element that performs the event handling for the remote port. This will have the mailbox commands and other items performed in the work element, not the irq. A much better method as the "irq" routine does not stall while performing all this deep handling code. Ensure that allocation failures are handled and send LOGO on failure. Additionally, enlarge the mailbox memory pool to reduce the possibility of additional allocation in this path. Link: https://lore.kernel.org/r/20201020202719.54726-3-james.smart@broadcom.com Fixes: 317aeb83 ("scsi: lpfc: Add blk_io_poll support for latency improvment") Cc: <stable@vger.kernel.org> # v5.9+ Co-developed-by:
-
James Smart authored
The following calltrace was seen: BUG: sleeping function called from invalid context at mm/slab.h:494 ... Call Trace: dump_stack+0x9a/0xf0 ___might_sleep.cold.63+0x13d/0x178 slab_pre_alloc_hook+0x6a/0x90 kmem_cache_alloc_trace+0x3a/0x2d0 lpfc_sli4_nvmet_alloc+0x4c/0x280 [lpfc] lpfc_post_rq_buffer+0x2e7/0xa60 [lpfc] lpfc_sli4_hba_setup+0x6b4c/0xa4b0 [lpfc] lpfc_pci_probe_one_s4.isra.15+0x14f8/0x2280 [lpfc] lpfc_pci_probe_one+0x260/0x2880 [lpfc] local_pci_probe+0xd4/0x180 work_for_cpu_fn+0x51/0xa0 process_one_work+0x8f0/0x17b0 worker_thread+0x536/0xb50 kthread+0x30c/0x3d0 ret_from_fork+0x3a/0x50 A prior patch introduced a spin_lock_irqsave(hbalock) in the lpfc_post_rq_buffer() routine. Call trace is seen as the hbalock is held with interrupts disabled during a GFP_KERNEL allocation in lpfc_sli4_nvmet_alloc(). Fix by reordering locking so that hbalock not held when calling sli4_nvmet_alloc() (aka rqb_buf_list()). Link: https://lore.kernel.org/r/20201020202719.54726-2-james.smart@broadcom.com Fixes: 411de511 ("scsi: lpfc: Fix RQ empty firmware trap") Cc: <stable@vger.kernel.org> # v4.17+ Co-developed-by:
-
- 26 Oct, 2020 8 commits
-
-
Bodo Stroesser authored
scatter_data_area() and gather_data_area() are not easy to understand since data is copied in nested loops over sg_list and tcmu dbi list. Since sg list can contain only partly filled pages, the loop has to be prepared to handle sg pages not matching dbi pages one by one. Existing implementation uses kmap_atomic()/kunmap_atomic() due to performance reasons. But instead of using these calls strictly nested for sg and dpi pages, the code holds the mappings in an overlapping way, which indeed is a bug that would trigger on archs using highmem. The scatterlist lib contains the sg_miter_start/_next/_stop functions which can be used to simplify such complicated loops. The new code now processes the dbi list in the outer loop, while sg list is handled by the inner one. That way the code can take advantage of the sg_miter_* family calls. Calling sg_miter_stop() after the end of the inner loop enforces strict nesting of atomic kmaps. Since the nested loops in scatter_/gather_data_area were very similar, I replaced them by the new helper function tcmu_copy_data(). Link: https://lore.kernel.org/r/20201019115118.11949-1-bostroesser@gmail.comAcked-by:
Mike Christie <michael.christie@oracle.com> Signed-off-by:
Bodo Stroesser <bostroesser@gmail.com> Signed-off-by:
-
Tom Rix authored
A break is not needed if it is preceded by a return. Link: https://lore.kernel.org/r/20201019191950.10244-1-trix@redhat.comSigned-off-by:
Tom Rix <trix@redhat.com> Signed-off-by:
-
Tom Rix authored
A break is not needed if it is preceded by a return or goto. Link: https://lore.kernel.org/r/20201019142333.16584-1-trix@redhat.comSigned-off-by:
-
Shyam Sundar authored
Update documentation for sysfs nodes within: /sys/class/fc_host /sys/class/fc_remote_ports Link: https://lore.kernel.org/r/20201021092715.22669-6-njavali@marvell.comReviewed-by:Himanshu Madhani <himanshu.madhani@oracle.com> Signed-off-by:
Shyam Sundar <ssundar@marvell.com> Signed-off-by:
Nilesh Javali <njavali@marvell.com> Signed-off-by:
-
Shyam Sundar authored
Under fc_host_statistics add statistics for Congestion Signals that are delivered to the host as interrupt signals. Link: https://lore.kernel.org/r/20201021092715.22669-5-njavali@marvell.comReviewed-by:
-
Shyam Sundar authored
Parse the incoming FPIN packets and update the host and rport FPIN statistics based on the FPINs. Link: https://lore.kernel.org/r/20201021092715.22669-4-njavali@marvell.comReviewed-by:
-
Shyam Sundar authored
Add a structure for holding FPIN statistics, for host & rport respectively, and add associated sysfs nodes: /sys/class/fc_host/hostXX/statistics/ /sys/class/fc_remote_ports/rport-XX\:Y-Z/statistics/ Link: https://lore.kernel.org/r/20201021092715.22669-3-njavali@marvell.comReviewed-by: -
Shyam Sundar authored
Add Fabric Performance Impact Notification (FPIN) descriptor definitions for the following FPINs: - Delivery Notification Descriptor - Peer Congestion Notification Descriptor - Congestion Notification Descriptor Link: https://lore.kernel.org/r/20201021092715.22669-2-njavali@marvell.comReviewed-by:
-
- 25 Oct, 2020 2 commits
-
-
Linus Torvalds authored
-
Joe Perches authored
Use a more generic form for __section that requires quotes to avoid complications with clang and gcc differences. Remove the quote operator # from compiler_attributes.h __section macro. Convert all unquoted __section(foo) uses to quoted __section("foo"). Also convert __attribute__((section("foo"))) uses to __section("foo") even if the __attribute__ has multiple list entry forms. Conversion done using the script at: https://lore.kernel.org/lkml/75393e5ddc272dc7403de74d645e6c6e0f4e70eb.camel@perches.com/2-convert_section.plSigned-off-by:Joe Perches <joe@perches.com> Reviewed-by:
Nick Desaulniers <ndesaulniers@gooogle.com> Reviewed-by:
Miguel Ojeda <ojeda@kernel.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
