This was tested on actual hardware and found to work fine, but currently
the official specifications of this chip could not be obtained to
confirm the numbers.
Signed-off-by: Leonid Bloch <lbloch@janustech.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The DIO connector on the WAFER-945GSE is interfaced to GPIO ports
on the ITE IT8718F Super I/O chipset. From the datasheet of ITE IT8718F,
the GPIO interface is identical to IT8728, so just add it
to the same case as the other chip.
Signed-off-by: Ivan Podovalov <ipodovalov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add a check for unused gpios to avoid chip->request() call to client
driver for unused gpios.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This is a GPIO driver so include only <linux/gpio/driver.h>.
Drop the use of GPIOF_* flags: these are for consumers, not
drivers. Just return 0/1.

Cc: Stefan Agner <stefan@agner.ch>
Cc: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The bgpio_init() takes one of two arguments to specify a register
to set the direction of the GPIO line: either dirout that
indicates that a 1 in the bit in that register sets the
corresponding line to output, or dirin which indicates that
a 1 in the bit in that register sets the corresponding line to
input. Conversely setting the bit to 0 on these will turn the
line into input and output respectively. One of these can
be defined but not both.

This means that a platform that sets a bit to 1 for output
only defines dirout and a platform that sets a bit to 0 for
output only defines dirin. In short this defines the polarity
of the direction register.

Both can also be left as NULL meaning the GPIO chip is either
input only or output only.

Tomer Maimon discovered that for get/set chips (those where the
get and set registers are defined but no separate clear register,
and specifying BGPIOF_READ_OUTPUT_REG_SET so that we say we
want to read the output value from the SET register)
we are unconditionally reading the value from the SET register
when the direction bit is 1 and from the DAT register when the
direction bit is 0, not taking the direction bit polarity into
account.

It would be expected that when the direction bit is inverted
(dirin is defined but not dirout) we read the current value from
the DAT register when the bit is 1 and from the SET register
when the bit is 0.

Currently only some versions of ATH79, brcmstb, some versions of
CLP711x, GE, IOP and Loongson use the dirin mode (a 1 in the
register means input). They are unaffected because
BGPIOF_READ_OUTPUT_REG_SET is not set on any of them. (They
do not read back the SET register to figure out the output
value.) So this is no regression with current drivers.

However the behaviour is wrong and does not work with Tomer's
new driver where he needs to use the BGIOF_READ_OUTPUT_REG_SET.
This fixes the above issue by:

- Instead of defining separate functions for the inverted case,
  set up a flag in the gpio_chip that indicates that the
  direction is inverted.
- Remove the special inverted functions for setting
  input/output and getting the direction, rely on the flag
  instead.
- Respect this flag in bgpio_get_set() and
  bgpio_get_set_multiple()
Reported-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This is a GPIO driver so use only <linux/gpio/driver.h>.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This is a GPIO driver so include only <linux/gpio/driver.h>.

Cc: Richard Röjfors <richard.rojfors@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This driver includes the legacy <linux/gpio.h> and
<linux/of_gpio.h> but all it needs is really <linux/gpio/driver.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Some platforms are not setting of_node in the driver. On these platforms
defining gpio-reserved-ranges on device tree leads to kernel crash.

It is due to some parts of the gpio core relying on the driver to set up
of_node,while other parts do themselves.This inconsistent behaviour leads
to a crash.

gpiochip_add_data_with_key() calls gpiochip_init_valid_mask() with of_node
as NULL. of_gpiochip_add() fills "of_node" and calls
of_gpiochip_init_valid_mask().

The fix is to move the assignment to chip->of_node from of_gpiochip_add()
to gpiochip_add_data_with_key().
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

gpiochip_lock_as_irq() may return a few error codes,
bail out if it fails with corresponding returned code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

gpiochip_lock_as_irq() may return a few error codes,
bail out if it fails with corresponding returned code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

gpiochip_lock_as_irq() may return a few error codes,
do not shadow them by -ENOSPC and let caller to decide.

No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

gpiochip_lock_as_irq() may return a few error codes,
do not shadow them by -EINVAL and let caller to decide.

No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

gpiochip_lock_as_irq() may return a few error codes,
do not shadow them by -EINVAL and let caller to decide.

No functional change intended.

Cc: Hoan Tran <hotran@apm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

gpiochip_lock_as_irq() may return a few error codes,
do not shadow them by -EINVAL and let caller to decide.

No functional change intended.

Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

gpiochip_lock_as_irq() may return a few error codes,
do not shadow them by -EINVAL and let caller to decide.

No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

In Rockchip RK3328, the output only GPIO_MUTE pin, originally for codec
mute control, can also be used for general purpose. It is manipulated by
the GRF_SOC_CON10 register in GRF. Aside from the GPIO_MUTE pin, the HDMI
pins can also be set in the same way.

Currently this GRF GPIO controller only supports the mute pin. If needed
in the future, the HDMI pins support can also be added.
Signed-off-by: Levin Du <djw@t-chip.com.cn>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This should make applications utilizing whole banks work faster.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/gpio/gpio-pxa.c: In function "pxa_gpio_probe":
drivers/gpio/gpio-pxa.c:629:35: warning:
 variable "gpio_offset" set but not used [-Wunused-but-set-variable]
  int irq0 = 0, irq1 = 0, irq_mux, gpio_offset = 0;
                                   ^
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

From the datasheet, the GPIO interface is identical to IT8728 (same
description), so just add it to the same case as the other chip.
Signed-off-by: Vincent Prince <vincent.prince.fr@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

There should not be anything more than stated by the name of newly
introduced constants, i.e.
	GPIOD_OUT_LOW_OPEN_DRAIN == GPIOD_OUT_LOW + open drain
and nothing more.

Make it better to read and slightly more robust by using GPIOD_OUT_LOW
and GPIOD_OUT_HIGH constants with open drain flag.

No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Since commit e45d1c80 ("gpio: put GPIO IRQs into their own lock
class") and commit a0a8bcf4 ("gpiolib: irqchip: use different
lockdep class for each gpio irqchip") GPIO lib takes care of lockdep
classes. In fact, gpiochip_irq_map() overwrites the class anyway, so
the lockdep class set by the driver is useless. Remove it.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Fix the following sparse error:

drivers/gpio/gpio-ath79.c:54:16: error: return expression in void function
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Acked-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

There is no need for splitting the writel() call in two lines.

Make it fit into a single line instead.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The pxa3xx driver uses the pinctrl-single driver since a while which
does not implement a .gpio_set_direction() callback. The pinmux core
will simply return 0 in this case, and the pxa3xx gpio driver hence
believes the pinctrl driver did its job and returns as well.

This effectively makes pxa_gpio_direction_{input,output} no-ops.

To fix this, do not call into the pinctrl subsystem for the PXA3xx
platform for now. We can revert this once the pinctrl-single driver
learned to support setting pin directions.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

If ioh_gpio_probe() fails on devm_irq_alloc_descs() then chip may point
to any element of chip_save array, so reverse iteration from pointer chip
may become chip_save[-1] and gpiochip_remove() will operate with wrong
memory.

The patch fix the error path of ioh_gpio_probe() to correctly bypass
chip_save array.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Actually report the error code from devm_regulator_get() which may as
well just be a probe deferral.

This is e.g. what one gets upon booting a Colibri T20:

gpiochip_add_data_with_key: GPIOs 0..223 (tegra-gpio) failed to register
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Commit 36b31279 ("gpiolib: Respect error code of ->get_direction()")
broke tegra_gpio_irq_set_type() because requesting of GPIO direction must
be done after enabling GPIO function for a pin.

This patch fixes drivers probe failure like this:

 gpio gpiochip0: (tegra-gpio): gpiochip_lock_as_irq: cannot get GPIO direction
 tegra-gpio 6000d000.gpio: unable to lock Tegra GPIO 144 as IRQ

Fixes: 36b31279 ("gpiolib: Respect error code of ->get_direction()")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

GPIO registers could lose context on i.MX7D, when
enter LPSR mode, the whole SoC will be powered off
except LPSR domain, GPIO banks will lose context
in this case, need to restore the context after
resume from LPSR mode.

This patch adds new compatible string for i.MX7D
which supports GPIO power off feature in suspend,
and adds the GPIO save/restore operations in noirq
suspend/resume phase, since GPIO is fundamental
module which could be used by other peripherals'
resume phase.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Morten Hein Tiljeset <morten.tiljeset@prevas.dk>
Reviewed-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

It's actually fine to read values of output lines. This was also
allowed by the legacy sysfs interface.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

User space can currently both read and set values of input lines using
the character device. This was not allowed by the old sysfs interface
nor is it a correct behavior.

Check the first descriptor in the set for the OUT flag when asked to
set values and return -EPERM if the line is input.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Allow gpiolib to read back the current I/O direction configuration by
implementing the .get_direction() callback.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

One line in gpiolib_dbg_show() still fits 80 characters, so,
join it to be like that in order to increase readability.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference
a bit later in the code.

This is detected by Coccinelle semantic patch.

@@
expression pdev, res, n, t, e, e1, e2;
@@

res = platform_get_resource(pdev, t, n);
+ if (!res)
+   return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Compile-testing the driver fails unless OF_GPIO is enabled:

drivers/gpio/gpio-mt7621.c: In function 'mediatek_gpio_bank_probe':
drivers/gpio/gpio-mt7621.c:228:10: error: 'struct gpio_chip' has no member named 'of_node'

Fixes: 4ba9c3af ("gpio: mt7621: Add a driver for MT7621")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Gcc cannot always see that BUG_ON(1) is guaranteed to not
return, so we get a warning message in some configurations:

drivers/gpio/gpio-aspeed.c: In function 'bank_reg':
drivers/gpio/gpio-aspeed.c:244:1: error: control reaches end of non-void function [-Werror=return-type]

Using a plain BUG() is easier here and avoids the problem.

Fixes: 44ddf559 ("gpio: aspeed: Rework register type accessors")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Two out of three calls to ->get_direction (excluding, of course,
gpiod_get_direction() itself) are using gpiod_get_direction() and
one is still open coded.

Replace the latter one to use same API for sake of consistency.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Since we put static variable to a header file it's copied to each module
that includes the header. But not all of them are actually used it.

Mark gpio_suffixes array with __maybe_unused to hide a compiler warning:

In file included from
drivers/gpio/gpiolib-legacy.c:6:0:
drivers/gpio/gpiolib.h:95:27: warning: ‘gpio_suffixes’ defined but not used [-Wunused-const-variable=]
 static const char * const gpio_suffixes[] = { "gpios", "gpio" };
                           ^~~~~~~~~~~~~
In file included from drivers/gpio/gpiolib-devprop.c:17:0:
drivers/gpio/gpiolib.h:95:27: warning: ‘gpio_suffixes’ defined but not used [-Wunused-const-variable=]
 static const char * const gpio_suffixes[] = { "gpios", "gpio" };
                           ^~~~~~~~~~~~~
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Following logic from commit: 22f6592b, GPIOHANDLE_REQUEST_OUTPUT
should handle errors same way as GPIOHANDLE_REQUEST_INPUT does, or else
the following error occurs:

gpio-mockup-chardev: gpio<gpiochip1> line<0> test flag<0x2> value<0>: No
such file or directory

despite the real result of gpio_pin_test(), gpio_debugfs_get() and
gpiotools_request_linehandle() functions.
Signed-off-by: Rafael David Tinoco <rafael.tinoco@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>