During resume, tick_resume_broadcast() programs the broadcast timer in
oneshot mode unconditionally. On the platforms where broadcast timer
is not really required, this will generate spurious broadcast timer
ticks upon resume. For example, on the always running apic timer
platforms with HPET, I see spurious hpet tick once every ~5minutes
(which is the 32-bit hpet counter wraparound time).

Similar to boot time, during resume make the oneshot mode setting of
the broadcast clock event device conditional on the state of active
broadcast users.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: svenjoac@gmx.de
Cc: torvalds@linux-foundation.org
Cc: rjw@sisk.pl
Link: http://lkml.kernel.org/r/1334802459.28674.209.camel@sbsiddha-desk.sc.intel.comSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

Santosh found another trap when we avoid to initialize the broadcast
device in the switch_to_oneshot code. The broadcast device might be
still in SHUTDOWN state when we actually need to use it. That
obviously breaks, as set_next_event() is called on a shutdown
device. This did not break on x86, but Suresh analyzed it:

From the review, most likely on Sven's system we are force enabling
the hpet using the pci quirk's method very late. And in this case,
hpet_clockevent (which will be global_clock_event) handler can be
null, specifically as this platform might not be using deeper c-states
and using the reliable APIC timer.

Prior to commit 'fa4da365', that handler will be set to
'tick_handle_oneshot_broadcast' when we switch the broadcast timer to
oneshot mode, even though we don't use it. Post commit
'fa4da365', we stopped switching the broadcast mode to oneshot
as this is not really needed and his platform's global_clock_event's
handler will remain null. While on my SNB laptop, same is set to
'clockevents_handle_noop' because hpet gets enabled very early. (noop
handler on my platform set when the early enabled hpet timer gets
replaced by the lapic timer).

But the commit 'fa4da365' tracked the broadcast timer mode in
the SW as oneshot, even though it didn't touch the HW timer. During
resume however, tick_resume_broadcast() saw the SW broadcast mode as
oneshot and actually programmed the broadcast device also into oneshot
mode. So this triggered the null pointer de-reference after the hpet
wraps around and depending on what the hpet counter is set to. On the
normal platforms where hpet gets enabled early we should be seeing a
spurious interrupt (in my SNB laptop I see one spurious interrupt
after around 5 minutes ;) which is 32-bit hpet counter wraparound
time), but that's a separate issue.

Enforce the mode setting when trying to set an event.
Reported-and-tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: torvalds@linux-foundation.org
Cc: svenjoac@gmx.de
Cc: rjw@sisk.pl
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1204181723350.2542@ionos

Sven Joachim reported, that suspend/resume on rc3 trips over a NULL
pointer dereference. Linus spotted the clockevent handler being NULL.

commit fa4da365(clockevents: tTack broadcast device mode change in
tick_broadcast_switch_to_oneshot()) tried to fix a problem with the
broadcast device setup, which was introduced in commit 77b0d60c(
clockevents: Leave the broadcast device in shutdown mode when not
needed).

The initial commit avoided to set up the broadcast device when no
broadcast request bits were set, but that left the broadcast device
disfunctional. In consequence deep idle states which need the
broadcast device were not woken up.

commit fa4da365 tried to fix that by initializing the state of the
broadcast facility, but that missed the fact, that nothing initializes
the event handler and some other state of the underlying clock event
device.

The fix is to revert both commits and make only the mode setting of
the clock event device conditional on the state of active broadcast
users. 

That initializes everything except the low level device mode, but this
happens when the broadcast functionality is invoked by deep idle.
Reported-and-tested-by: Sven Joachim <svenjoac@gmx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1204181205540.2542@ionos

Pull ext4 regression fixes from Ted Ts'o:
 "This fixes a scalability problem reported by Andi Kleen and Tim Chen;
  they were quite secretive about the precise nature of their workload,
  but they later admitted that it only showed up when they were using a
  large sparse file, so the amount of data I/O that was needed was close
  to zero.

  I'm not sure how realistic this is and it's only a regression if you
  consider changes made since 2.6.39 to be a "regression" vis-a-vis the
  policy regarding post-merge window bug fixes, but Linus agreed it was
  worth fixing, so I'm including it in this pull request.

  This also fixes the journalled quota mount options, which I
  accidentally broke while I was cleaning up the mount option handling."

* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix handling of journalled quota options
  ext4: address scalability issue by removing extent cache statistics

Pull vfs fixes from Al Viro:
 "A bunch of endianness fixes and a couple of nfsd error value fixes.

  Speaking of endianness stuff, I'm rather tempted to slap

	ccflags-y += -D__CHECK_ENDIAN__

  in fs/Makefile, if not making it default for the entire tree; nfsd
  regressions I've caught make one hell of a pile and we'd obviously
  benefit from having that kind of stuff caught earlier..."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  lockd: fix the endianness bug
  ocfs2: ->e_leaf_clusters endianness breakage
  ocfs2: ->rl_count endianness breakage
  ocfs: ->rl_used breakage on big-endian
  ocfs2: ->l_next_free_req breakage on big-endian
  btrfs: btrfs_root_readonly() broken on big-endian
  ext4: fix endianness breakage in ext4_split_extent_at()
  nfsd: fix compose_entry_fh() failure exits
  nfsd: fix error value on allocation failure in nfsd4_decode_test_stateid()
  nfsd: fix endianness breakage in TEST_STATEID handling
  nfsd: fix error values returned by nfsd4_lockt() when nfsd_open() fails
  nfsd: fix b0rken error value for setattr on read-only mount

Pull CIFS fixes from Steve French.

* git://git.samba.org/sfrench/cifs-2.6:
  Fix number parsing in cifs_parse_mount_options
  Cleanup handling of NULL value passed for a mount option

Pull perf fixes from Ingo Molnar.

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86: Handle failures of parsing immediate operands in the instruction decoder
  perf archive: Correct cutting of symbolic link
  perf tools: Ignore auto-generated bison/flex files
  perf tools: Fix parsers' rules to dependencies
  perf tools: fix NO_GTK2 Makefile config error
  perf session: Skip event correctly for unknown id/machine

Pull virtio fixes from Michael S. Tsirkin:
 "Here are some virtio fixes for 3.4: a test build fix, a patch by Ren
  fixing naming for systems with a massive number of virtio blk devices,
  and balloon fixes for powerpc by David Gibson.

  There was some discussion about Ren's patch for virtio disc naming:
  some people wanted to move the legacy name mangling function to the
  block core.  But there's no concensus on that yet, and we can always
  deduplicate later.  Added comments in the hope that this will stop
  people from copying this legacy naming scheme into future drivers."

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  virtio_balloon: fix handling of PAGE_SIZE != 4k
  virtio_balloon: Fix endian bug
  virtio_blk: helper function to format disk names
  tools/virtio: fix up vhost/test module build

Some shortcomings introduced into pci_restore_state() by commit
26f41062 ("PCI: check for pci bar restore completion and retry")
have been fixed by recent commit ebfc5b80 ("PCI: Fix regression in
pci_restore_state(), v3"), but that commit treats all PCI devices as
those with Type 0 configuration headers.

That is not entirely correct, because Type 1 and Type 2 headers have
different layouts.  In particular, the area occupied by BARs in Type 0
config headers contains the secondary status register in Type 1 ones and
it doesn't make sense to retry the restoration of that register even if
the value read back from it after a write is not the same as the written
one (it very well may be different).

For this reason, make pci_restore_state() only retry the restoration
of BARs for Type 0 config headers.  This effectively makes it behave
as before commit 26f41062 for all header types except for Type 0.
Tested-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

I'm dropping off as Documentation/ maintainer.
Rob Landley has agreed to take it over.  Thanks, Rob.

I'll still be around reviewing patches and testing.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Michel Lespinasse cleaned up the futex calling conventions in commit
37a9d912 ("futex: Sanitize cmpxchg_futex_value_locked API").

But the ia64 implementation was subtly broken.  Gcc does not know that
register "r8" will be updated by the fault handler if the cmpxchg
instruction takes an exception.  So it feels safe in letting the
initialization of r8 slide to after the cmpxchg.  Result: we always
return 0 whether the user address faulted or not.

Fix by moving the initialization of r8 into the __asm__ code so gcc
won't move it.

Reported-by: <emeric.maschino@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=42757
Tested-by: <emeric.maschino@gmail.com>
Acked-by: Michel Lespinasse <walken@google.com>
Cc: stable@vger.kernel.org # v2.6.39+
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 26092bf5 broke handling of journalled quota mount options by
trying to parse argument of every mount option as a number.  Fix this
by dealing with the quota options before we call match_int().

Thanks to Jan Kara for discovering this regression.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>

Revert the --strict test for the old preferred block
comment style in drivers/net and net/
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Andi Kleen and Tim Chen have reported that under certain circumstances
the extent cache statistics are causing scalability problems due to
cache line bounces.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@vger.kernel.org

This can happen if the instruction is much longer than the maximum length,
or if insn->opnd_bytes is manually changed.

This patch also fixes warnings from -Wswitch-default flag.
Reported-by: Prashanth Nageshappa <prashanth@linux.vnet.ibm.com>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jim Keniston <jkenisto@linux.vnet.ibm.com>
Cc: Linux-mm <linux-mm@kvack.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Anton Arapov <anton@redhat.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: yrl.pp-manager.tt@hitachi.com
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20120413032427.32577.42602.stgit@localhost.localdomainSigned-off-by: Ingo Molnar <mingo@kernel.org>

Pull ARM fixes from Russell King:
 "Nothing too disasterous, the biggest thing being the removal of the
  regulator support for vcore in the AMBA driver; only one SoC was using
  this and it got broken during the last merge window, which then
  started causing problems for other people.  Mutual agreement was
  reached for it to be removed."

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: 7386/1: jump_label: fixup for rename to static_key
  ARM: 7384/1: ThumbEE: Disable userspace TEEHBR access for !CONFIG_ARM_THUMBEE
  ARM: 7382/1: mm: truncate memory banks to fit in 4GB space for classic MMU
  ARM: 7359/2: smp_twd: Only wait for reprogramming on active cpus
  ARM: 7383/1: nommu: populate vectors page from paging_init
  ARM: 7381/1: nommu: fix typo in mm/Kconfig
  ARM: 7380/1: DT: do not add a zero-sized memory property
  ARM: 7379/1: DT: fix atags_to_fdt() second call site
  ARM: 7366/3: amba: Remove AMBA level regulator support
  ARM: 7377/1: vic: re-read status register before dispatching each IRQ handler
  ARM: 7368/1: fault.c: correct how the tsk->[maj|min]_flt gets incremented

The 'max' range needs to be unsigned, since the size of the user address
space is bigger than 2GB.

We know that 'count' is positive in 'long' (that is checked in the
caller), so we will truncate 'max' down to something that fits in a
signed long, but before we actually do that, that comparison needs to be
done in unsigned.

Bug introduced in commit 92ae03f2 ("x86: merge 32/64-bit versions of
'strncpy_from_user()' and speed it up").  On x86-64 you can't trigger
this, since the user address space is much smaller than 63 bits, and on
x86-32 it works in practice, since you would seldom hit the strncpy
limits anyway.

I had actually tested the corner-cases, I had only tested them on
x86-64.  Besides, I had only worried about the case of a pointer *close*
to the end of the address space, rather than really far away from it ;)

This also changes the "we hit the user-specified maximum" to return
'res', for the trivial reason that gcc seems to generate better code
that way.  'res' and 'count' are the same in that case, so it really
doesn't matter which one we return.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

c5905afb ("static keys: Introduce 'struct static_key'...") renamed
struct jump_label_key to struct static_key.  Fixup ARM for this to
eliminate these build warnings:

  include/linux/jump_label.h:113:2:
  warning: passing argument 1 of 'arch_static_branch' from incompatible pointer type
  include/asm/jump_label.h:17:82:
  note: expected 'struct jump_label_key *' but argument is of type 'struct static_key *'
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Currently when ThumbEE is not enabled (!CONFIG_ARM_THUMBEE) the ThumbEE
register states are not saved/restored at context switch. The default state
of the ThumbEE Ctrl register (TEECR) allows userspace accesses to the
ThumbEE Base Handler register (TEEHBR). This can cause unexpected behaviour
when people use ThumbEE on !CONFIG_ARM_THUMBEE kernels, as well as allowing
covert communication - eg between userspace tasks running inside chroot
jails.

This patch sets up TEECR in order to prevent user-space access to TEEHBR
when !CONFIG_ARM_THUMBEE. In this case, tasks are sent SIGILL if they try to
access TEEHBR.

Cc: stable@vger.kernel.org
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jonathan Austin <jonathan.austin@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

If a bank of memory spanning the 4GB boundary is added on a !CONFIG_LPAE
kernel then we will hang early during boot since the memory bank will
have wrapped around to zero.

This patch truncates memory banks for !LPAE configurations when the end
address is not representable in 32 bits.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

During booting of cpu1, there is a short window where cpu1
is online, but not active where cpu1 is occupied by waiting
to become active. If cpu0 then decides to schedule something
on cpu1 and wait for it to complete, before cpu0 has set
cpu1 active, we have a deadlock.

Typically it's this CPU frequency transition that happens at
this time, so let's just not wait for it to happen, it will
happen whenever the CPU eventually comes online instead.

Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Rickard Andersson <rickard.andersson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Commit 26f41062 ("PCI: check for pci bar restore completion and
retry") attempted to address problems with PCI BAR restoration on
systems where FLR had not been completed before pci_restore_state() was
called, but it did that in an utterly wrong way.

First off, instead of retrying the writes for the BAR registers only, it
did that for all of the PCI config space of the device, including the
status register (whose value after the write quite obviously need not be
the same as the written one).  Second, it added arbitrary delay to
pci_restore_state() even for systems where the PCI config space
restoration was successful at first attempt.  Finally, the mdelay(10) it
added to every iteration of the writing loop was way too much of a delay
for any reasonable device.

All of this actually caused resume failures for some devices on Mikko's
system.

To fix the regression, make pci_restore_state() only retry the writes
for BAR registers and only wait if the first read from the register
doesn't return the written value.  Additionaly, make it wait for 1 ms,
instead of 10 ms, after every failing attempt to write into config
space.
Reported-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull "ARM: a few more SoC fixes for 3.4-rc" from Olof Johansson:
 - A handful of warning and build fixes for Qualcomm MSM
 - Build/warning and bug fixes for Samsung Exynos
 - A fix from Rob Herring that removes misplaced interrupt-parent
   properties from a few device trees
 - A fix to OMAP dealing with cpufreq build errors, removing some of the
   offending code since it was redundant anyway

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: OMAP: clock: cleanup CPUfreq leftovers, fix build errors
  ARM: dts: remove blank interrupt-parent properties
  ARM: EXYNOS: Fix Kconfig dependencies for device tree enabled machine files
  ARM: EXYNOS: Remove broken config values for touchscren for NURI board
  ARM: EXYNOS: set fix xusbxti clock for NURI and Universal210 boards
  ARM: EXYNOS: fix regulator name for NURI board
  ARM: SAMSUNG: make SAMSUNG_PM_DEBUG select DEBUG_LL
  ARM: msm: Fix section mismatches in proc_comm.c
  video: msm: Fix section mismatches in mddi.c
  arm: msm: trout: fix compile failure
  arm: msm: halibut: remove unneeded fixup
  ARM: EXYNOS: Add PDMA and MDMA physical base address defines
  ARM: S5PV210: Fix compiler warning in dma.c file
  ARM: EXYNOS: Fix compile error in exynos5250-cpufreq.c
  ARM: EXYNOS: Add missing definition for IRQ_I2S0
  ARM: S5PV210: fix unused LDO supply field from wm8994_pdata

Pull another round of sound fixes from Takashi Iwai:
 "A few regression fixes for Realtek HD-audio codecs, mainly specific to
  some laptop models."

* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda/realtek - Fix mem leak (and rid us of trailing whitespace).
  ALSA: hda/realtek - Add quirk for Mac Pro 5,1 machines
  ALSA: hda/realtek - Add a fixup entry for Acer Aspire 8940G
  ALSA: hda/realtek - Fix GPIO1 setup for Acer Aspire 4930 & co
  ALSA: hda/realtek - Add a few ALC882 model strings back

Commit 18a4d0a2 ("[SCSI] Handle disk devices which can not process
medium access commands") introduced a bug in which we would attempt to
dereference the scsi driver even when the device had no ULD attached.

Ensure that a driver is registered and make the driver accessor function
more resilient to errors during device discovery.
Reported-by: Elric Fu <elricfu1@gmail.com>
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

As reported by David Gibson, current code handles PAGE_SIZE != 4k
completely wrong which can lead to guest memory corruption errors:

- page_to_balloon_pfn is wrong: e.g. on system with 64K page size
 it gives the same pfn value for 16 different pages.

- we also need to convert back to linux pfns when we free.

- for each linux page we need to tell host about multiple balloon
  pages, but code only adds one pfn to the array.

This patch fixes all that, tested with a 64k ppc64 kernel.
Reported-by: David Gibson <david@gibson.dropbear.id.au>
Tested-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

Although virtio config space fields are usually in guest-native endian,
the spec for the virtio balloon device explicitly states that both fields
in its config space are little-endian.

However, the current virtio_balloon driver does not have a suitable endian
swap for the 'num_pages' field, although it does have one for the 'actual'
field.  This patch corrects the bug, adding sparse annotation while we're
at it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

Merge tag 'perf-urgent-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent

Pull perf tooling fixes from Arnaldo Carvalho de Melo:

. Properly handle ~/.debug, the build id cache, when it is a symlink,
  fix from Chanho Park

. Fixes for the parser generation process, from Jiri Olsa and Namhyung Kim

. Fix build when NO_GTK2 is specified, From Stephane Eranian

. When a machine is not found, bump the relevant error stat but return
  0, so that we correctly move to the next perf event. Fix from Jiri Olsa
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>

Merge branch 'v3.4-samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes

* 'v3.4-samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: EXYNOS: Fix Kconfig dependencies for device tree enabled machine files
  ARM: EXYNOS: Remove broken config values for touchscren for NURI board
  ARM: EXYNOS: set fix xusbxti clock for NURI and Universal210 boards
  ARM: EXYNOS: fix regulator name for NURI board
  ARM: SAMSUNG: make SAMSUNG_PM_DEBUG select DEBUG_LL
  ARM: EXYNOS: Add PDMA and MDMA physical base address defines
  ARM: S5PV210: Fix compiler warning in dma.c file
  ARM: EXYNOS: Fix compile error in exynos5250-cpufreq.c
  ARM: EXYNOS: Add missing definition for IRQ_I2S0
  ARM: S5PV210: fix unused LDO supply field from wm8994_pdata

Now that we have OPP layer, and OMAP CPUfreq driver is using it, we no
longer need/use the clock framework code for filling up CPUfreq
tables.  Remove it.

Removing this code also eliminates build errors when CPU_FREQ_TABLE
support is not enabled.

Thanks to Russell King for pointing out the parts I missed under
plat-omap in the original version and also pointing out the build
errors when CPUFREQ_TABLE support was not enabled.

Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

These were incorrectly introduced and can cause problems for of_irq_init.

The correct way to define a root controller is no interrupt-parent set at
all or the interrupt-parent is set to the root controller itself when
inherited from a parent node.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Tested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

From David Brown:
  "Here are some fixes for msm that fix problems caused by the latest
   ARM code.  The ones from Daniel remove unneeded fixups that now
   cause compilation failures.  Mine fix section mismatches, that were
   incompletely fixed earlier."

* 'msm-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
  ARM: msm: Fix section mismatches in proc_comm.c
  video: msm: Fix section mismatches in mddi.c
  arm: msm: trout: fix compile failure
  arm: msm: halibut: remove unneeded fixup

If a '$PERF_BUILDID_DIR'(typically $HOME/.debug) is a symbolic link
directory, cutting of the path will fail.

Here is an example where a buildid directory is a symbolic link.

/ # ls -al /root
lrwxrwxrwx    1 root     root            13 Mar 26  2012 /root -> opt/home/root
/ # cd ~
/opt/home/root # perf record -a -g sleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.322 MB perf.data (~14057 samples) ]
/opt/home/root # perf archive
tar: Removing leading `/' from member names
Now please run:

$ tar xvf perf.data.tar.bz2 -C ~/.debug

wherever you need to run 'perf report' on.
/opt/home/root # mkdir temp
/opt/home/root # tar xf perf.data.tar.bz2 -C ./temp
/opt/home/root # find ./temp -name "*kernel*"
./temp/opt/home/root/.debug/[kernel.kallsyms]

-> If successfully cut off the path, [kernel.kallsyms] is located
in top of the archived file.

This patch enables to cut correctly even if the buildid directory
is a symbolic link.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1333348109-12598-1-git-send-email-chanho61.park@samsung.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

The commit 65f3e56e ("perf tools: Remove auto-generated bison/flex
files") removed those files from git, so they'll be listed on untracked
files after building perf. Fix it.
Signed-off-by: Namhyung Kim <namhyung.kim@lge.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1333948274-20043-1-git-send-email-namhyung.kim@lge.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

Currently the parsers objects (bison/flex related) are each time perf
is built. No matter the generated files are already in place, the
parser generation is executed every time.

Changing the rules to have proper flex/bison objects generation
dependencies.

The parsers code is not rebuilt until the flex/bison source files
are touched. Also when flex/bison source is changed, only dependent
objects are rebuilt.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1334140791-3024-1-git-send-email-jolsa@redhat.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

Add config dependency for Exynos4 and Exynos5 device tree enabled machine
files on config options ARCH_EXYNOS4 and ARCH_EXYNOS5 respectively.
Enabling machine support without proper ARCH support enabled is incorrect.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Pull perf tool fixes from Ingo Molnar.

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf kvm: Finding struct machine fails for PERF_RECORD_MMAP
  perf annotate: Validate addr in symbol__inc_addr_samples
  perf hists browser: Fix NULL deref in hists browsing code
  perf hists: Catch and handle out-of-date hist entry maps.
  perf annotate: Fix hist decay
  perf top: Add intel_idle to the skip list

GCC's NULL is actually __null, which allows detecting some questionable
NULL usage and warn about it.  Moreover each platform/compiler should
have its own stddef.h anyway (which is different from linux/stddef.h).

So there's no good reason to leak kernel's NULL to userspace and
override what the compiler provides.
Signed-off-by: Luboš Luňák <l.lunak@suse.cz>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The atmel_mxt_ts driver has been extended to support more 'configuration
objects' in commit 81c88a71 ("Input: atmel_mxt_ts - update object list"),
what broke the configuration values for NURI board. These values are
optional anyway, so remove them to get the driver working correctly.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>