such utilities are currently duplicated on all UDC
drivers basically with the same structure. Let's group
all implementations into one generic implementation
and get rid of that duplication.
Signed-off-by: Felipe Balbi <balbi@ti.com>

Git does not care about CVS markers.
Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Use "static const char *const" instead of "static const char *".
Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Use DEFINE_PCI_DEVICE_TABLE instead of "const struct pci_device_id".
Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Remove an unnecessary level of indentation.
Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Remove unnecessary whitespaces.
Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Remove a bunch of unneeded braces.
Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

When loading g_ether gadget, there is below message:

Backtrace:
[<80012248>] (dump_backtrace+0x0/0x10c) from [<803cb42c>] (dump_stack+0x18/0x1c)
r7:00000000 r6:80512000 r5:8052bef8 r4:80513f30
[<803cb414>] (dump_stack+0x0/0x1c) from [<8000feb4>] (show_regs+0x44/0x50)
[<8000fe70>] (show_regs+0x0/0x50) from [<8004c840>] (__schedule_bug+0x68/0x84)
r5:8052bef8 r4:80513f30
[<8004c7d8>] (__schedule_bug+0x0/0x84) from [<803cd0e4>] (__schedule+0x4b0/0x528)
r5:8052bef8 r4:809aad00
[<803ccc34>] (__schedule+0x0/0x528) from [<803cd214>] (_cond_resched+0x44/0x58)
[<803cd1d0>] (_cond_resched+0x0/0x58) from [<800a9488>] (dma_pool_alloc+0x184/0x250)
 r5:9f9b4000 r4:9fb4fb80
 [<800a9304>] (dma_pool_alloc+0x0/0x250) from [<802a8ad8>] (fsl_req_to_dtd+0xac/0x180)
[<802a8a2c>] (fsl_req_to_dtd+0x0/0x180) from [<802a8ce4>] (fsl_ep_queue+0x138/0x274)
[<802a8bac>] (fsl_ep_queue+0x0/0x274) from [<7f004328>] (composite_setup+0x2d4/0xfac [g_ether])
[<7f004054>] (composite_setup+0x0/0xfac [g_ether]) from [<802a9bb4>] (fsl_udc_irq+0x8dc/0xd38)
[<802a92d8>] (fsl_udc_irq+0x0/0xd38) from [<800704f8>] (handle_irq_event_percpu+0x54/0x188)
[<800704a4>] (handle_irq_event_percpu+0x0/0x188) from [<80070674>] (handle_irq_event+0x48/0x68)
[<8007062c>] (handle_irq_event+0x0/0x68) from [<800738ec>] (handle_level_irq+0xb4/0x138)
 r5:80514f94 r4:80514f40
 [<80073838>] (handle_level_irq+0x0/0x138) from [<8006ffa4>] (generic_handle_irq+0x38/0x44)
 r7:00000012 r6:80510b1c r5:80529860 r4:80512000
 [<8006ff6c>] (generic_handle_irq+0x0/0x44) from [<8000f4c4>] (handle_IRQ+0x54/0xb4)
[<8000f470>] (handle_IRQ+0x0/0xb4) from [<800085b8>] (tzic_handle_irq+0x64/0x94)
 r9:412fc085 r8:00000000 r7:80513f30 r6:00000001 r5:00000000
 r4:00000000
 [<80008554>] (tzic_handle_irq+0x0/0x94) from [<8000e680>] (__irq_svc+0x40/0x60)

The reason of above dump message is calling dma_poll_alloc with can-schedule
mem_flags at atomic context.

To fix this problem, below changes are made:
- fsl_req_to_dtd doesn't need to be protected by spin_lock_irqsave,
as struct usb_request can be access at process context. Move lock
to beginning of hardware visit (fsl_queue_td).
- Change the memory flag which using to allocate dTD descriptor buffer,
the memory flag can be from gadget layer.

It is tested at i.mx51 bbg board with g_mass_storage, g_ether, g_serial.

Cc: stable@vger.kernel.org
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch fixup below warning on device_unregister()

renesas_usbhs renesas_usbhs.1: host probed
renesas_usbhs renesas_usbhs.1: gadget probed
renesas_usbhs renesas_usbhs.1: irq request err
------------[ cut here ]------------
WARNING: at ${LINUX}/drivers/base/core.c:1)
Device 'gadget' does not have a release() function, it is broken and must be fi.
Modules linked in:
[<c000e25c>] (unwind_backtrace+0x0/0xe4) from [<c0016960>] (warn_slowpath_commo)
[<c0016960>] (warn_slowpath_common+0x4c/0x64) from [<c00169f8>] (warn_slowpath_)
[<c00169f8>] (warn_slowpath_fmt+0x2c/0x3c) from [<c0185b80>] (device_release+0x)
[<c0185b80>] (device_release+0x70/0x84) from [<c013e300>] (kobject_cleanup+0x58)
[<c013e300>] (kobject_cleanup+0x58/0x6c) from [<c01cba14>] (usbhs_mod_gadget_re)
[<c01cba14>] (usbhs_mod_gadget_remove+0x3c/0x6c) from [<c01c8384>] (usbhs_mod_p)
[<c01c8384>] (usbhs_mod_probe+0x68/0x80) from [<c01c7f84>] (usbhs_probe+0x1cc/0)
...

Cc: stable@vger.kernel.org
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This fix a bug in f_serial, which expect the ep->desc to be NULL after
disabling an endpoint.

Cc: stable@vger.kernel.org
Signed-off-by: Ido Shayevitz <idos@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

drivers/usb/gadget/at91_udc.c included 'linux/prefetch.h' twice,
remove the duplicate.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This is a flexible USB Audio Class 2.0 compliant gadget driver that
implements a simple topology with a virtual sound card exposed at
the function side.

The driver doesn't expect any real audio codec to be present on the
function - the audio streams are simply sinked to and sourced from a
virtual ALSA sound card created. The user-space application may choose
to do whatever it wants with the data received from the USB Host and
choose to provide whatever it wants as audio data to the USB Host.

Capture(USB-Out) and Playback(USB-In) can be run at independent
configurations specified via module parameters while loading the driver.

Make this new version as the default selection by a new Kconfig choice.
Signed-off-by: Yadi Brar <yadi.brar01@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Move manufacturer and product string ids into audio.c so
as to be reusable by the new uac2 version of gadget driver.
Signed-off-by: Yadi Brar <yadi.brar01@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add missing, but needed, ACHeader and FormatType descriptor definitions.
Signed-off-by: Yadi Brar <yadi.brar01@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The extant USB-Audio function driver complies to UAC_1 spec.
So name the files accordingly, paving way for inclusion of
a new UAC_2 specified driver.
Signed-off-by: Yadi Brar <yadi.brar01@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The current renesas_usbhs driver triggers

BUG: scheduling while atomic: ksoftirqd/0/3/0x00000102

with enabled CONFIG_DEBUG_ATOMIC_SLEEP, by submitting DMA transfers from
an atomic (tasklet) context, which is not supported by the shdma dmaengine
driver. Fix it by switching to a work.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

list.h already provide helpers to find the first entry and to move list
nodes to the tail of another list. This patch simply uses those helpers,
no functional changes.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch adds SS descriptors to the ACM & generic serial gadget. The
ACM part was tested with minicom + dummy + send / receive files over
ttyACM <=> ttyGS0.
The generic serial part (f_serial) was not tested (haven't found a
driver on the host side).
The nokia & multi gadget use HS at most.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Since commit 72c973dd aka ("usb: gadget: add usb_endpoint_descriptor to
struct usb_ep) the descriptor is part of the ep. Most gadgets like
g_zero or masstorage call config_ep_by_speed() to grab an available
endpoint which may be used for FS/HS/SS bulk/iso/intr and in a second
they assign the proper descriptor by calling config_ep_by_speed(). This
is good so far. A few of them like ncm call config_ep_by_speed() only if
ep->desc not assigned earlier. That means ep->desc is never assigned if
the endpoint was used by another gadget before it was removed.

Some of those gadgets also assign ep->driver_data to NULL on reset or
ep_disable part _but_ keep a reference to this endpoint. At ep_enable
time they assign driver_data to their private data. This probably needs
a clean up of its own.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Problem:
 pch_udc continues operation even if VBUS becomes Low.
 pch_udc performs D+ pulling up before VBUS becomes High.
 USB device should be controlled according to VBUS state.

Root cause:
 The current pch_udc is not always monitoring VBUS.

Solution:
 The change of VBUS is detected using an interrupt of GPIO.
 If VBUS became Low, pch_udc handles 'disconnect'.
 After VBUS became High, a pull improves D+, and pch_udc
 handles 'connect'.

[ balbi@ti.com : make it actually compile ]
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Problem:
 In USB Suspend, pch_udc handles 'disconnect'.

Root cause:
 The current pch_udc is not monitoring VBUS.
 When USB cable is disconnected, USB Device Controller generates
 an interrupt of USB Suspend.
 pch_udc cannot distinguish it is USB Suspend or disconnect.
 Therefore, pch_udc handles 'disconnect' after an interrupt of
 USB Suspend happend.

Solution:
 VBUS is detected through GPIO.
 After an interrupt produced USB Suspend, if VBUS is Low,
 pch_udc handles 'disconnect'.
 If VBUS is High, pch_udc handles 'suspend'.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

_ep to ep is a pointer substraction so ep won't be zero unless _ep was
8. This was not intendent by the author, it was probably a typo while
checking for NULL of the argument.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>

If the stream check fails then we leave ep->desc assigend but we return
with an error code. The caller assumes the endpoint is not enabled
(which is the case) but it can not enable it again due to this
assigment.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add IAD to bind the two interfaces of ECM so that it works properly
in composite gadget mode.
Signed-off-by: Thirupathi <thirupathi.chippakurthy@stericsson.com>
Signed-off-by: Praveena Nadahally <praveen.nadahally@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Remove one define of FSG_NO_INTR_EP and we still have that we can use.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The m.nazarewicz@samsung.com email address is no longer valid,
so this commit replaces it with mina86@mina86.com which is
employer-agnostic and thus should be valid for foreseeable
feature.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch converts checkpatch output of
|./scripts/checkpatch.pl drivers/usb/gadget/dummy_hcd.c -file

from
|total: 22 errors, 174 warnings, 2642 lines checked

to
|total: 0 errors, 0 warnings, 2632 lines checked
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch makes use of usb_endpoint_type() instead of the open coding.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

dummy_hcd provides (alloc|free)_stream() callbacks but there are not
doing anything. The transfer side also lacks matching of streams. This
patch changes this and implements stream allocation / de-allocation
support and proper urb <=> req matching.
The UDC side exposes a limit of 16 streams. DWC3, the only USB3 UDC has
no limitations in this regard except that it _needs_ to know that
streams will be used at the ep_enable time. At the host side, there is
no real limit either: XHCI can allocate any number of streams as long as
it does not run out of memory. The UAS gadget currently requests 16
streams and the UAS host side fallbacks from the requested 256 down to
16 which is fine.
From the UASP point of view (the only specified user), the number of
used streams does not really matter. The only limitation is that the
host may not use a higher stream than the gadget requested and can deal
with.

The dummy stream support has been modelled after current UAS + XHCI +
DWC3 + UASP usage which helps me testing:
- the device announces that each ep supports 16 streams (even it could
  more than that).
- the device side looks into Companion descriptor at ep_enable time and
  enables them according to it.
- the host side tries to enable the requested number of streams but the
  upper limit is the Comanion descriptor. None (zero streams) is an
  error condition, less is okay.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

ISSUE:
Adding debugging messages.

CAUSE:
The debugging messages are added to make sure of that major interrupt events
are occurring.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

ISSUE:
USB Suspend interrupts occur frequently.

CAUSE:
When it is called pch_udc_reconnect() in USB Suspend, it repeats reset and
Suspend.

SOLUTION:
pch_udc_reconnect() does not enable all interrupts.  When an enumeration event
occurred the driver enables all interrupts.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

ISSUE:
After a USB cable is connect/disconnected, the system rarely freezes.

CAUSE:
Since the USB device controller cannot know to disconnect the USB cable, when
it is used without detecting VBUS by GPIO, the UDC driver does not notify to
USB Gadget.

Since USB Gadget cannot know to disconnect, a false setting occurred when the
USB cable is connected/disconnect repeatedly.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

ISSUE:
After USB Suspend, a system rarely freezes.

CAUSE:
When USB Suspend occurred, the driver is not notifying
a gadget of the event.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

ISSUE:
If the return value of pch_udc_pcd_init() is False, the return value of
this function is unsettled.
Since pch_udc_pcd_init() always returns 0, there is not actually the issue.

CAUSE:
If pch_udc_pcd_init() is True, the variable, retval, is not set for an
appropriate value.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

ISSUE:
When the driver notifies a gadget of a disconnect event, a system
rarely freezes.

CAUSE:
When the driver calls dev->driver->disconnect(), it is not calling
spin_unlock().
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This will enable the system to check for activity of the usb gadget
and also in a later patch to control the usbphy power-domain.
When handling the power domain there, it will be possible to remove
another reference to architecture code.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The helper functions were definied but never used until now.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The SUDMAC uses 8-bit width only. So, when the driver uses SUDMAC,
we have to clear the MBW_32.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

In case of the SH7757, the irq number of USB module and SUDMAC
are the same. So, we have to set the IRQF_SHARED in such a case.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

We've dereferenced req already, and we checked for bogus parameters at
the start of the function.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>