- 22 Jun, 2019 40 commits
-
-
Yoshihiro Shimoda authored
[ Upstream commit 315ca92d ] The sh_eth_close() resets the MAC and then calls phy_stop() so that mdio read access result is incorrect without any error according to kernel trace like below: ifconfig-216 [003] .n.. 109.133124: mdio_access: ee700000.ethernet-ffffffff read phy:0x01 reg:0x00 val:0xffff According to the hardware manual, the RMII mode should be set to 1 before operation the Ethernet MAC. However, the previous code was not set to 1 after the driver issued the soft_reset in sh_eth_dev_exit() so that the mdio read access result seemed incorrect. To fix the issue, this patch adds a condition and set the RMII mode register in sh_eth_dev_exit() for R-Car Gen2 and RZ/A1 SoCs. Note that when I have tried to move the sh_eth_dev_exit() calling after phy_stop() on sh_eth_close(), but it gets worse (kernel panic happened and it seems that a register is accessed while the clock is off). Signed-off-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Sami Tolvanen authored
[ Upstream commit 1e29ab31 ] Calling sys_ni_syscall through a syscall_fn_t pointer trips indirect call Control-Flow Integrity checking due to a function type mismatch. Use SYSCALL_DEFINE0 for __arm64_sys_ni_syscall instead and remove the now unnecessary casts. Signed-off-by:
Sami Tolvanen <samitolvanen@google.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Sami Tolvanen authored
[ Upstream commit 0e358bd7 ] Although a syscall defined using SYSCALL_DEFINE0 doesn't accept parameters, use the correct function type to avoid indirect call type mismatches with Control-Flow Integrity checking. Signed-off-by:
-
Sami Tolvanen authored
[ Upstream commit 8ef8f368 ] Syscall wrappers in <asm/syscall_wrapper.h> use const struct pt_regs * as the argument type. Use const in syscall_fn_t as well to fix indirect call type mismatches with Control-Flow Integrity checking. Signed-off-by:
Mark Rutland <mark.rutland@arm.com> Signed-off-by:
-
Geert Uytterhoeven authored
[ Upstream commit 6954158a ] With gcc 4.1: sound/firewire/fireface/ff-protocol-latter.c: In function ‘latter_switch_fetching_mode’: sound/firewire/fireface/ff-protocol-latter.c:97: warning: integer constant is too large for ‘long’ type sound/firewire/fireface/ff-protocol-latter.c: In function ‘latter_begin_session’: sound/firewire/fireface/ff-protocol-latter.c:170: warning: integer constant is too large for ‘long’ type sound/firewire/fireface/ff-protocol-latter.c:197: warning: integer constant is too large for ‘long’ type sound/firewire/fireface/ff-protocol-latter.c:205: warning: integer constant is too large for ‘long’ type sound/firewire/fireface/ff-protocol-latter.c: In function ‘latter_finish_session’: sound/firewire/fireface/ff-protocol-latter.c:214: warning: integer constant is too large for ‘long’ type Fix this by adding the missing "ULL" suffixes. Add the same suffix to the last constant, to maintain consistency. Fixes: fd1cc9de ("ALSA: fireface: add support for Fireface UCX") Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Reviewed-by:
Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Paul Mackerras authored
[ Upstream commit 5a3f4936 ] Currently the HV KVM code takes the kvm->lock around calls to kvm_for_each_vcpu() and kvm_get_vcpu_by_id() (which can call kvm_for_each_vcpu() internally). However, that leads to a lock order inversion problem, because these are called in contexts where the vcpu mutex is held, but the vcpu mutexes nest within kvm->lock according to Documentation/virtual/kvm/locking.txt. Hence there is a possibility of deadlock. To fix this, we simply don't take the kvm->lock mutex around these calls. This is safe because the implementations of kvm_for_each_vcpu() and kvm_get_vcpu_by_id() have been designed to be able to be called locklessly. Signed-off-by:
Paul Mackerras <paulus@ozlabs.org> Reviewed-by:
Cédric Le Goater <clg@kaod.org> Signed-off-by:
-
Paul Mackerras authored
[ Upstream commit 1659e27d ] Currently the Book 3S KVM code uses kvm->lock to synchronize access to the kvm->arch.rtas_tokens list. Because this list is scanned inside kvmppc_rtas_hcall(), which is called with the vcpu mutex held, taking kvm->lock cause a lock inversion problem, which could lead to a deadlock. To fix this, we add a new mutex, kvm->arch.rtas_token_lock, which nests inside the vcpu mutexes, and use that instead of kvm->lock when accessing the rtas token list. This removes the lockdep_assert_held() in kvmppc_rtas_tokens_free(). At this point we don't hold the new mutex, but that is OK because kvmppc_rtas_tokens_free() is only called when the whole VM is being destroyed, and at that point nothing can be looking up a token in the list. Signed-off-by:
-
Paul Mackerras authored
[ Upstream commit 0d4ee88d ] Currently the HV KVM code uses kvm->lock in conjunction with a flag, kvm->arch.mmu_ready, to synchronize MMU setup and hold off vcpu execution until the MMU-related data structures are ready. However, this means that kvm->lock is being taken inside vcpu->mutex, which is contrary to Documentation/virtual/kvm/locking.txt and results in lockdep warnings. To fix this, we add a new mutex, kvm->arch.mmu_setup_lock, which nests inside the vcpu mutexes, and is taken in the places where kvm->lock was taken that are related to MMU setup. Additionally we take the new mutex in the vcpu creation code at the point where we are creating a new vcore, in order to provide mutual exclusion with kvmppc_update_lpcr() and ensure that an update to kvm->arch.lpcr doesn't get missed, which could otherwise lead to a stale vcore->lpcr value. Signed-off-by:
-
Gen Zhang authored
[ Upstream commit 50fbc13d ] In flush_cache_ent(), 'ce->ce_path' is allocated by kstrdup_const(). It should be freed by kfree_const(), rather than kfree(). Signed-off-by:
Gen Zhang <blackgod016574@gmail.com> Reviewed-by:
Paulo Alcantara <palcantara@suse.de> Signed-off-by:
Steve French <stfrench@microsoft.com> Signed-off-by:
-
Ross Lagerwall authored
[ Upstream commit d10e0cc1 ] During a suspend/resume, the xenwatch thread waits for all outstanding xenstore requests and transactions to complete. This does not work correctly for transactions started by userspace because it waits for them to complete after freezing userspace threads which means the transactions have no way of completing, resulting in a deadlock. This is trivial to reproduce by running this script and then suspending the VM: import pyxs, time c = pyxs.client.Client(xen_bus_path="/dev/xen/xenbus") c.connect() c.transaction() time.sleep(3600) Even if this deadlock were resolved, misbehaving userspace should not prevent a VM from being migrated. So, instead of waiting for these transactions to complete before suspending, store the current generation id for each transaction when it is started. The global generation id is incremented during resume. If the caller commits the transaction and the generation id does not match the current generation id, return EAGAIN so that they try again. If the transaction was instead discarded, return OK since no changes were made anyway. This only affects users of the xenbus file interface. In-kernel users of xenbus are assumed to be well-behaved and complete all transactions before freezing. Signed-off-by:
Ross Lagerwall <ross.lagerwall@citrix.com> Reviewed-by:
Juergen Gross <jgross@suse.com> Signed-off-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by:
-
YueHaibing authored
[ Upstream commit 41349672 ] Fixes gcc '-Wunused-but-set-variable' warning: drivers/xen/pvcalls-front.c: In function pvcalls_front_sendmsg: drivers/xen/pvcalls-front.c:543:25: warning: variable bedata set but not used [-Wunused-but-set-variable] drivers/xen/pvcalls-front.c: In function pvcalls_front_recvmsg: drivers/xen/pvcalls-front.c:638:25: warning: variable bedata set but not used [-Wunused-but-set-variable] They are never used since introduction. Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Reviewed-by:
-
Madalin Bucur authored
[ Upstream commit 7aae703f ] Make sure only the portals for the online CPUs are used. Without this change, there are issues when someone boots with maxcpus=n, with n < actual number of cores available as frames either received or corresponding to the transmit confirmation path would be offered for dequeue to the offline CPU portals, getting lost. Signed-off-by:
Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by:
-
Randy Dunlap authored
[ Upstream commit 9a626c4a ] Fix build errors on ia64 when DISCONTIGMEM=y and NUMA=y by exporting paddr_to_nid(). Fixes these build errors: ERROR: "paddr_to_nid" [sound/core/snd-pcm.ko] undefined! ERROR: "paddr_to_nid" [net/sunrpc/sunrpc.ko] undefined! ERROR: "paddr_to_nid" [fs/cifs/cifs.ko] undefined! ERROR: "paddr_to_nid" [drivers/video/fbdev/core/fb.ko] undefined! ERROR: "paddr_to_nid" [drivers/usb/mon/usbmon.ko] undefined! ERROR: "paddr_to_nid" [drivers/usb/core/usbcore.ko] undefined! ERROR: "paddr_to_nid" [drivers/md/raid1.ko] undefined! ERROR: "paddr_to_nid" [drivers/md/dm-mod.ko] undefined! ERROR: "paddr_to_nid" [drivers/md/dm-crypt.ko] undefined! ERROR: "paddr_to_nid" [drivers/md/dm-bufio.ko] undefined! ERROR: "paddr_to_nid" [drivers/ide/ide-core.ko] undefined! ERROR: "paddr_to_nid" [drivers/ide/ide-cd_mod.ko] undefined! ERROR: "paddr_to_nid" [drivers/gpu/drm/drm.ko] undefined! ERROR: "paddr_to_nid" [drivers/char/agp/agpgart.ko] undefined! ERROR: "paddr_to_nid" [drivers/block/nbd.ko] undefined! ERROR: "paddr_to_nid" [drivers/block/loop.ko] undefined! ERROR: "paddr_to_nid" [drivers/block/brd.ko] undefined! ERROR: "paddr_to_nid" [crypto/ccm.ko] undefined! Reported-by:
kbuild test robot <lkp@intel.com> Signed-off-by:
Randy Dunlap <rdunlap@infradead.org> Cc: Tony Luck <tony.luck@intel.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: linux-ia64@vger.kernel.org Signed-off-by:
Tony Luck <tony.luck@intel.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Thomas Richter authored
[ Upstream commit 6738028d ] Command 'perf record' and 'perf report' on a system without kernel debuginfo packages uses /proc/kallsyms and /proc/modules to find addresses for kernel and module symbols. On x86 this works for root and non-root users. On s390, when invoked as non-root user, many of the following warnings are shown and module symbols are missing: proc/{kallsyms,modules} inconsistency while looking for "[sha1_s390]" module! Command 'perf record' creates a list of module start addresses by parsing the output of /proc/modules and creates a PERF_RECORD_MMAP record for the kernel and each module. The following function call sequence is executed: machine__create_kernel_maps machine__create_module modules__parse machine__create_module --> for each line in /proc/modules arch__fix_module_text_start Function arch__fix_module_text_start() is s390 specific. It opens file /sys/module/<name>/sections/.text to extract the module's .text section start address. On s390 the module loader prepends a header before the first section, whereas on x86 the module's text section address is identical the the module's load address. However module section files are root readable only. For non-root the read operation fails and machine__create_module() returns an error. Command perf record does not generate any PERF_RECORD_MMAP record for loaded modules. Later command perf report complains about missing module maps. To fix this function arch__fix_module_text_start() always returns success. For root users there is no change, for non-root users the module's load address is used as module's text start address (the prepended header then counts as part of the text section). This enable non-root users to use module symbols and avoid the warning when perf report is executed. Output before: [tmricht@m83lp54 perf]$ ./perf report -D | fgrep MMAP 0 0x168 [0x50]: PERF_RECORD_MMAP ... x [kernel.kallsyms]_text Output after: [tmricht@m83lp54 perf]$ ./perf report -D | fgrep MMAP 0 0x168 [0x50]: PERF_RECORD_MMAP ... x [kernel.kallsyms]_text 0 0x1b8 [0x98]: PERF_RECORD_MMAP ... x /lib/modules/.../autofs4.ko.xz 0 0x250 [0xa8]: PERF_RECORD_MMAP ... x /lib/modules/.../sha_common.ko.xz 0 0x2f8 [0x98]: PERF_RECORD_MMAP ... x /lib/modules/.../des_generic.ko.xz Signed-off-by:
Thomas Richter <tmricht@linux.ibm.com> Reviewed-by:
Hendrik Brueckner <brueckner@linux.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Link: http://lkml.kernel.org/r/20190522144601.50763-4-tmricht@linux.ibm.comSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Namhyung Kim authored
[ Upstream commit 6584140b ] It seems that the current code lacks holding the namespace lock in thread__namespaces(). Otherwise it can see inconsistent results. Signed-off-by:
Namhyung Kim <namhyung@kernel.org> Cc: Hari Bathini <hbathini@linux.vnet.ibm.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Krister Johansen <kjlx@templeofstupid.com> Link: http://lkml.kernel.org/r/20190522053250.207156-2-namhyung@kernel.orgSigned-off-by:
-
Harald Freudenberger authored
[ Upstream commit 7379e652 ] The zcrypt device driver does not handle CPRBs which address a control domain correctly. This fix introduces a workaround: The domain field of the request CPRB is checked if there is a valid domain value in there. If this is true and the value is a control only domain (a domain which is enabled in the crypto config ADM mask but disabled in the AQM mask) the CPRB is forwarded to the default usage domain. If there is no default domain, the request is rejected with an ENODEV. This fix is important for maintaining crypto adapters. For example one LPAR can use a crypto adapter domain ('Control and Usage') but another LPAR needs to be able to maintain this adapter domain ('Control'). Scenarios like this did not work properly and the patch enables this. Signed-off-by:
Harald Freudenberger <freude@linux.ibm.com> Signed-off-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by:
-
Shawn Landden authored
[ Upstream commit 97acec7d ] This strncat() is safe because the buffer was allocated with zalloc(), however gcc doesn't know that. Since the string always has 4 non-null bytes, just use memcpy() here. CC /home/shawn/linux/tools/perf/util/data-convert-bt.o In file included from /usr/include/string.h:494, from /home/shawn/linux/tools/lib/traceevent/event-parse.h:27, from util/data-convert-bt.c:22: In function ‘strncat’, inlined from ‘string_set_value’ at util/data-convert-bt.c:274:4: /usr/include/powerpc64le-linux-gnu/bits/string_fortified.h:136:10: error: ‘__builtin_strncat’ output may be truncated copying 4 bytes from a string of length 4 [-Werror=stringop-truncation] 136 | return __builtin___strncat_chk (__dest, __src, __len, __bos (__dest)); | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Signed-off-by:
Shawn Landden <shawn@git.icu> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Wang Nan <wangnan0@huawei.com> LPU-Reference: 20190518183238.10954-1-shawn@git.icu Link: https://lkml.kernel.org/n/tip-289f1jice17ta7tr3tstm9jm@git.kernel.orgSigned-off-by:
-
Sahitya Tummala authored
[ Upstream commit f6122ed2 ] In the vfs_statx() context, during path lookup, the dentry gets added to sd->s_dentry via configfs_attach_attr(). In the end, vfs_statx() kills the dentry by calling path_put(), which invokes configfs_d_iput(). Ideally, this dentry must be removed from sd->s_dentry but it doesn't if the sd->s_count >= 3. As a result, sd->s_dentry is holding reference to a stale dentry pointer whose memory is already freed up. This results in use-after-free issue, when this stale sd->s_dentry is accessed later in configfs_readdir() path. This issue can be easily reproduced, by running the LTP test case - sh fs_racer_file_list.sh /config (https://github.com/linux-test-project/ltp/blob/master/testcases/kernel/fs/racer/fs_racer_file_list.sh) Fixes: 76ae281f ('configfs: fix race between dentry put and lookup') Signed-off-by:
Sahitya Tummala <stummala@codeaurora.org> Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Bard Liao authored
[ Upstream commit fa763f1b ] We observed the same issue as reported by commit a8d7bde2 ("ALSA: hda - Force polling mode on CFL for fixing codec communication") We don't have a better solution. So apply the same workaround to CNL. Signed-off-by:
Bard Liao <yung-chuan.liao@linux.intel.com> Signed-off-by:
-
Yingjoe Chen authored
[ Upstream commit a0692f0e ] If I2C_M_RECV_LEN check failed, msgs[i].buf allocated by memdup_user will not be freed. Pump index up so it will be freed. Fixes: 838bfa60 ("i2c-dev: Add support for I2C_M_RECV_LEN") Signed-off-by:
Yingjoe Chen <yingjoe.chen@mediatek.com> Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Dmitry Bogdanov authored
[ Upstream commit eaeb3b74 ] Driver stops producing skbs on ring if a packet with FCS error was coalesced into LRO session. Ring gets hang forever. Thats a logical error in driver processing descriptors: When rx_stat indicates MAC Error, next pointer and eop flags are not filled. This confuses driver so it waits for descriptor 0 to be filled by HW. Solution is fill next pointer and eop flag even for packets with FCS error. Fixes: bab6de8f ("net: ethernet: aquantia: Atlantic A0 and B0 specific functions.") Signed-off-by:
Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by:
Dmitry Bogdanov <dmitry.bogdanov@aquantia.com> Signed-off-by:
-
Igor Russkikh authored
[ Upstream commit 31bafc49 ] In case no other traffic happening on the ring, full tx cleanup may not be completed. That may cause socket buffer to overflow and tx traffic to stuck until next activity on the ring happens. This is due to logic error in budget variable decrementor. Variable is compared with zero, and then post decremented, causing it to become MAX_INT. Solution is remove decrementor from the `for` statement and rewrite it in a clear way. Fixes: b647d398 ("net: aquantia: Add tx clean budget and valid budget handling logic") Signed-off-by:
-
Lucas Stach authored
[ Upstream commit 1396500d ] The devcoredump needs to operate on a stable state of the MMU while it is writing the MMU state to the coredump. The missing lock allowed both the userspace submit, as well as the GPU job finish paths to mutate the MMU state while a coredump is under way. Fixes: a8c21a54 (drm/etnaviv: add initial etnaviv DRM driver) Reported-by:
David Jander <david@protonic.nl> Signed-off-by:
Lucas Stach <l.stach@pengutronix.de> Tested-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
-
Rafael J. Wysocki authored
[ Upstream commit 9a51c6b1 ] Both acpi_pci_need_resume() and acpi_dev_needs_resume() check if the current ACPI wakeup configuration of the device matches what is expected as far as system wakeup from sleep states is concerned, as reflected by the device_may_wakeup() return value for the device. However, they only should do that if wakeup.flags.valid is set for the device's ACPI companion, because otherwise the wakeup.prepare_count value for it is meaningless. Add the missing wakeup.flags.valid checks to these functions. Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by:
-
Kees Cook authored
[ Upstream commit 3e66b7cc ] Building with Clang reports the redundant use of MODULE_DEVICE_TABLE(): drivers/net/ethernet/dec/tulip/de4x5.c:2110:1: error: redefinition of '__mod_eisa__de4x5_eisa_ids_device_table' MODULE_DEVICE_TABLE(eisa, de4x5_eisa_ids); ^ ./include/linux/module.h:229:21: note: expanded from macro 'MODULE_DEVICE_TABLE' extern typeof(name) __mod_##type##__##name##_device_table \ ^ <scratch space>:90:1: note: expanded from here __mod_eisa__de4x5_eisa_ids_device_table ^ drivers/net/ethernet/dec/tulip/de4x5.c:2100:1: note: previous definition is here MODULE_DEVICE_TABLE(eisa, de4x5_eisa_ids); ^ ./include/linux/module.h:229:21: note: expanded from macro 'MODULE_DEVICE_TABLE' extern typeof(name) __mod_##type##__##name##_device_table \ ^ <scratch space>:85:1: note: expanded from here __mod_eisa__de4x5_eisa_ids_device_table ^ This drops the one further from the table definition to match the common use of MODULE_DEVICE_TABLE(). Fixes: 07563c71 ("EISA bus MODALIAS attributes support") Signed-off-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
-
Ioana Radulescu authored
[ Upstream commit bd8460fa ] Use PTR_ERR_OR_ZERO instead of PTR_ERR in cases where zero is a valid input. Reported by smatch. Signed-off-by:
Ioana Radulescu <ruxandra.radulescu@nxp.com> Signed-off-by:
-
Ioana Radulescu authored
[ Upstream commit 5a20a093 ] Smatch reports a potential spectre vulnerability in the dpaa2-eth driver, where the value of rxnfc->fs.location (which is provided from user-space) is used as index in an array. Add a call to array_index_nospec() to sanitize the access. Signed-off-by:
-
Pavel Begunkov authored
[ Upstream commit a278682d ] If io_copy_iov() fails, it will break the loop and report success, albeit partially completed operation. Signed-off-by:
Pavel Begunkov <asml.silence@gmail.com> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Biao Huang authored
[ Upstream commit f4ca7a92 ] 1. the frequency of csr clock is 66.5MHz, so the csr_clk value should be 0 other than 5. 2. the csr_clk can be got from device tree, so remove initialization here. Fixes: 9992f37e ("stmmac: dwmac-mediatek: add support for mt2712") Signed-off-by:
Biao Huang <biao.huang@mediatek.com> Signed-off-by:
-
Biao Huang authored
[ Upstream commit 5e7f7fc5 ] The specific clk_csr value can be zero, and stmmac_clk is necessary for MDC clock which can be set dynamically. So, change the condition from plat->clk_csr to plat->stmmac_clk to fix clk_csr can't be zero issue. Fixes: cd7201f4 ("stmmac: MDC clock dynamically based on the csr clock input") Signed-off-by:
Alexandre TORGUE <alexandre.torgue@st.com> Signed-off-by:
-
Biao Huang authored
[ Upstream commit 4523a561 ] Currently we will not update the receive descriptor tail pointer in stmmac_rx_refill. Rx dma will think no available descriptors and stop once received packets exceed DMA_RX_SIZE, so that the rx only test will fail. Update the receive tail pointer in stmmac_rx_refill to add more descriptors to the rx channel, so packets can be received continually Fixes: 54139cf3 ("net: stmmac: adding multiple buffers for rx") Signed-off-by:
-
Randy Dunlap authored
[ Upstream commit e9646f0f ] The gpio-adp5588 driver uses interfaces that are provided by GPIOLIB_IRQCHIP, so select that symbol in its Kconfig entry. Fixes these build errors: ../drivers/gpio/gpio-adp5588.c: In function ‘adp5588_irq_handler’: ../drivers/gpio/gpio-adp5588.c:266:26: error: ‘struct gpio_chip’ has no member named ‘irq’ dev->gpio_chip.irq.domain, gpio)); ^ ../drivers/gpio/gpio-adp5588.c: In function ‘adp5588_irq_setup’: ../drivers/gpio/gpio-adp5588.c:298:2: error: implicit declaration of function ‘gpiochip_irqchip_add_nested’ [-Werror=implicit-function-declaration] ret = gpiochip_irqchip_add_nested(&dev->gpio_chip, ^ ../drivers/gpio/gpio-adp5588.c:307:2: error: implicit declaration of function ‘gpiochip_set_nested_irqchip’ [-Werror=implicit-function-declaration] gpiochip_set_nested_irqchip(&dev->gpio_chip, ^ Fixes: 459773ae ("gpio: adp5588-gpio: support interrupt controller") Reported-by:
Bartosz Golaszewski <bgolaszewski@baylibre.com> Acked-by:
Michael Hennerich <michael.hennerich@analog.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Peter Zijlstra authored
[ Upstream commit 4d839dd9 ] We must use {READ,WRITE}_ONCE() on rb->user_page data such that concurrent usage will see whole values. A few key sites were missing this. Suggested-by:
Yabin Cui <yabinc@google.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: acme@kernel.org Cc: mark.rutland@arm.com Cc: namhyung@kernel.org Fixes: 7b732a75 ("perf_counter: new output ABI - part 1") Link: http://lkml.kernel.org/r/20190517115418.394192145@infradead.orgSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Peter Zijlstra authored
[ Upstream commit 3f9fbe9b ] Similar to how decrementing rb->next too early can cause data_head to (temporarily) be observed to go backward, so too can this happen when we increment too late. This barrier() ensures the rb->head load happens after the increment, both the one in the 'goto again' path, as the one from perf_output_get_handle() -- albeit very unlikely to matter for the latter. Suggested-by:
-
Yabin Cui authored
[ Upstream commit 1b038c6e ] In perf_output_put_handle(), an IRQ/NMI can happen in below location and write records to the same ring buffer: ... local_dec_and_test(&rb->nest) ... <-- an IRQ/NMI can happen here rb->user_page->data_head = head; ... In this case, a value A is written to data_head in the IRQ, then a value B is written to data_head after the IRQ. And A > B. As a result, data_head is temporarily decreased from A to B. And a reader may see data_head < data_tail if it read the buffer frequently enough, which creates unexpected behaviors. This can be fixed by moving dec(&rb->nest) to after updating data_head, which prevents the IRQ/NMI above from updating data_head. [ Split up by peterz. ] Signed-off-by:
-
Frank van der Linden authored
[ Upstream commit 2ac44ab6 ] For F17h AMD CPUs, the CPB capability ('Core Performance Boost') is forcibly set, because some versions of that chip incorrectly report that they do not have it. However, a hypervisor may filter out the CPB capability, for good reasons. For example, KVM currently does not emulate setting the CPB bit in MSR_K7_HWCR, and unchecked MSR access errors will be thrown when trying to set it as a guest: unchecked MSR access error: WRMSR to 0xc0010015 (tried to write 0x0000000001000011) at rIP: 0xffffffff890638f4 (native_write_msr+0x4/0x20) Call Trace: boost_set_msr+0x50/0x80 [acpi_cpufreq] cpuhp_invoke_callback+0x86/0x560 sort_range+0x20/0x20 cpuhp_thread_fun+0xb0/0x110 smpboot_thread_fn+0xef/0x160 kthread+0x113/0x130 kthread_create_worker_on_cpu+0x70/0x70 ret_from_fork+0x35/0x40 To avoid this issue, don't forcibly set the CPB capability for a CPU when running under a hypervisor. Signed-off-by:
Frank van der Linden <fllinden@amazon.com> Acked-by:
Borislav Petkov <bp@suse.de> Cc: Andy Lutomirski <luto@kernel.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: bp@alien8.de Cc: jiaxun.yang@flygoat.com Fixes: 02371991 ("x86/CPU/AMD: Set the CPB bit unconditionally on F17h") Link: http://lkml.kernel.org/r/20190522221745.GA15789@dev-dsk-fllinden-2c-c1893d73.us-west-2.amazon.com [ Minor edits to the changelog. ] Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit ccfb62f2 ] The user can change the device_name with the IMSETDEVNAME ioctl, but we need to ensure that the user's name is NUL terminated. Otherwise it could result in a buffer overflow when we copy the name back to the user with IMGETDEVINFO ioctl. I also changed two strcpy() calls which handle the name to strscpy(). Hopefully, there aren't any other ways to create a too long name, but it's nice to do this as a kernel hardening measure. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Jia-Ju Bai authored
[ Upstream commit 5bce256f ] In xhci_debugfs_create_slot(), kzalloc() can fail and dev->debugfs_private will be NULL. In xhci_debugfs_create_endpoint(), dev->debugfs_private is used without any null-pointer check, and can cause a null pointer dereference. To fix this bug, a null-pointer check is added in xhci_debugfs_create_endpoint(). This bug is found by a runtime fuzzing tool named FIZZER written by us. [subjet line change change, add potential -Mathais] Signed-off-by:
Jia-Ju Bai <baijiaju1990@gmail.com> Reviewed-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Anju T Sudhakar authored
[ Upstream commit b59bd352 ] Currently init_imc_pmu() can fail either because we try to register an IMC unit with an invalid domain (i.e an IMC node not supported by the kernel) or something went wrong while registering a valid IMC unit. In both the cases kernel provides a 'Register failed' error message. For example when trace-imc node is not supported by the kernel, but skiboot advertises a trace-imc node we print: IMC Unknown Device type IMC PMU (null) Register failed To avoid confusion just print the unknown device type message, before attempting PMU registration, so the second message isn't printed. Fixes: 8f95faaa ("powerpc/powernv: Detect and create IMC device") Reported-by:
Pavaman Subramaniyam <pavsubra@in.ibm.com> Signed-off-by:
Anju T Sudhakar <anju@linux.vnet.ibm.com> Reviewed-by:
Madhavan Srinivasan <maddy@linux.vnet.ibm.com> [mpe: Reword change log a bit] Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Tony Lindgren authored
[ Upstream commit 1cc54078 ] We need to always call clkdm_clk_enable() and clkdm_clk_disable() even the clkctrl clock(s) enabled for the domain do not have any gate register bits. Otherwise clockdomains may never get enabled except when devices get probed with the legacy "ti,hwmods" devicetree property. Fixes: 88a17252 ("clk: ti: add support for clkctrl clocks") Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
Stephen Boyd <sboyd@kernel.org> Signed-off-by:
-
