Merge tag 'omap-for-v4.5/dt-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

Second set of omap device tree changes for v4.5 merge window. This series
updates the EDMA bindings based on the various fixes to split EDMA into
separate independent devices. It also adds support for more devices on the
CompuLab cm-t335 and LogicPD Torpedo boards, and enables the new bindings
for qspi for am437x and dra7. There are also few dra7 regulator fixes, and
change of gpoi-key,wakeup to wakeup-source.

These depend on commit ae0add74 ("dmaengine: edma: DT: Change reserved
slot array from 16bit to 32bit type") already merged into mainline.

* tag 'omap-for-v4.5/dt-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP2+: LogicPD Torpedo: Add Touchscreen Support
  ARM: dts: DRA7-EVM: Add regulator-allow-bypass property for ldo9
  ARM: dts: DRA72-EVM: Add regulator-allow-bypass property for ldo1 and ldo2
  ARM: dts: AM4372: add entry for qspi mmap region
  ARM: dts: DRA7: add entry for qspi mmap region
  ARM: OMAP2+: LogicPD Torpedo: Revert Duplicative Entries
  ARM: OMAP2+: LogicPD Torpedo + Wireless: Add Bluetooth
  ARM: OMAP2+: LogicPD Torpedo: Add LCD Type 15 Support
  ARM: dts: cm-t335: add support for bluetooth
  ARM: dts: cm-t335: add support for DVI/LCD
  ARM: dts: cm-t335: add support for I2C GPIO expander
  ARM: dts: cm-t335: add support for SBC-T335
  ARM: dts: cm-t335: add support for USB0
  ARM: dts: omap: replace legacy *,wakeup property with wakeup-source
  ARM: dts: am335x: replace gpio-key,wakeup with wakeup-source property
  ARM: DTS: am437x: Use the new DT bindings for the eDMA3
  ARM: DTS: am33xx: Use the new DT bindings for the eDMA3
  dmaengine: edma: DT: Change reserved slot array from 16bit to 32bit type
  dmaengine: edma: DT: Change memcpy channel array from 16bit to 32bit type
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'socfpga_dts_for_v4.5_part_2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt

SoCFPGA DTS update for v4.5, part 2
- clean up mcvevk dts file, replace space with tab
- Disable SDMMC node in base socfpga.dtsi file

* tag 'socfpga_dts_for_v4.5_part_2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
  ARM: socfpga: dts: Enable MMC support at correct place in the DT
  ARM: socfpga: Repair incorrectly applied MCV patch
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'v4.5-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt

Another new soc - the rk3228 quad-core cortex-a7, a new rk3036 board,
support for the efuses on Rockchip socs and some improvements for
rk3288 regulators.

* tag 'v4.5-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  ARM: dts: rockchip: add the kylin board for rk3036
  ARM: dts: rockchip: add the sdio/sdmmc node for rk3036
  ARM: dts: rockchip: fix the pinctrl bias settings for rk3036
  ARM: dts: rockchip: add eFuse node for rk3188 SoCs
  ARM: dts: rockchip: add eFuse node for rk3066a SoCs
  ARM: dts: rockchip: add eFuse config of rk3288 SoC
  ARM: dts: rockchip: add rk3228-evb board
  ARM: dts: rockchip: add core rk3228 dtsi
  clk: rockchip: Add the clock ids of rk3288 eFuses
  ARM: dts: rockchip: Fix typo in rk3288 sdmmc card detect pin name
  ARM: dts: rockchip: fix voltage ranges for rk3288-evb-act8846 board
  ARM: dts: rockchip: move the public part to rk3288-evb common
  ARM: dts: rockchip: add 2 regulators for rk3288-evb-act8846
  ARM: dts: rockchip: correct the name of REG8 for rk3288-evb-act8846
  clk: rockchip: add dt-binding header for rk3228
  clk: rockchip: add id for mipidsi sclk on rk3288
Signed-off-by: Olof Johansson <olof@lixom.net>

Device Tree additions for LPC18xx platform

NXP LPC18xx EEPROM support plus board updates for CIAA board and
EA4357 Dev kit.

* tag 'lpc18xx_dts_for_4.5' of https://github.com/manabian/linux-lpc:
  ARM: dts: lpc4337-ciaa: add i2c0 and devices
  ARM: dts: lpc4337-ciaa: enable SCT-PWM
  ARM: dts: lpc4357-ea4357: add mma7455 i2c accelerometer
  ARM: dts: lpc4357: enable EEPROM memory
  ARM: dts: lpc18xx: add EEPROM memory node
Signed-off-by: Olof Johansson <olof@lixom.net>

Add regulators to the scpsys binding.

Move the include of the reset contoller to include/dt-bindings/reset.

Add basic support for mt2701 SoC and evaluation board.

* tag 'v4.4-next-dts' of https://github.com/mbgg/linux-mediatek:
  dt-bindings: soc: Add supplies for Mediatek SCPSYS unit
  ARM: mediatek: DT: Move reset controller constants into common location
  ARM: dts: mediatek: add MT2701 basic support
  Document: DT: Add bindings for mediatek MT2701 SoC Platform
Signed-off-by: Olof Johansson <olof@lixom.net>

mvebu dt for 4.5 (part 3)

Add dts for the following boards:
- Zyxel NSA325
- PogoPlug series 4
Add GPU support for Dove
Update boolean property to wakeup source for isil

* tag 'mvebu-dt-4.5-3' of git://git.infradead.org/linux-mvebu:
  ARM: dts: armada: replace isil, irq2-can-wakeup-machine with wakeup-source property
  ARM: dts: enable GPU for SolidRun's Cubox
  ARM: dts: dove: add DT GPU support
  ARM: mvebu: kirkwood: add PogoPlug series 4 device tree
  ARM: mvebu: add kirkwood compatibles for cloudengine boards
  ARM: dts: kirkwood: Add DTS for Zyxel NSA325
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-dt3-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Third Round of Renesas ARM Based SoC DT Updates for v4.5

* Use SoC-specific usb-dmac and IPMMU compatibility strings
* Add internal delay for i2c IPs
* Add missing serial devices to r8a7793
* Enable DMA for r8a7793 serial devices
* Add serial port config to chosen/stdout-path
* Tidyup #sound-dai-cells settings for r8a7798/bockw
* Remove deprecated #gpio-range-cells from r8a7793
* Add EtherAVB support to r8a7791
* Add MSIOF support to sh73a0

* tag 'renesas-dt3-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (25 commits)
  ARM: shmobile: r8a779x: use SoC-specific usb-dmac compatibility strings
  ARM: shmobile: r8a7794: IPMMU compat string SoC part number update
  ARM: shmobile: r8a7793: IPMMU compat string SoC part number update
  ARM: shmobile: r8a7791: IPMMU compat string SoC part number update
  ARM: shmobile: r8a7790: IPMMU compat string SoC part number update
  ARM: shmobile: r8a7794: dtsi: add internal delay for i2c IPs
  ARM: shmobile: r8a7791: dtsi: add internal delay for i2c IPs
  ARM: shmobile: r8a7790: dtsi: add internal delay for i2c IPs
  ARM: shmobile: r8a7793: Describe DMA for the serial ports
  ARM: shmobile: r8a7793: Add missing serial devices to DT
  ARM: shmobile: lager dts: Add serial port config to chosen/stdout-path
  ARM: shmobile: porter dts: Add serial port config to chosen/stdout-path
  ARM: shmobile: silk dts: Add serial port config to chosen/stdout-path
  ARM: shmobile: gose dts: Add serial port config to chosen/stdout-path
  ARM: shmobile: bockw dts: Update console parameters
  ARM: shmobile: ape6evm dts: Add serial port config to chosen/stdout-path
  ARM: shmobile: alt dts: Add serial port config to chosen/stdout-path
  ARM: shmobile: koelsch dts: Add serial port config to chosen/stdout-path
  ARM: shmobile: r8a7778: tidyup #sound-dai-cells settings
  ARM: shmobile: bockw dts: Override #sound-dai-cells to zero
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'qcom-dt-for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt

Qualcomm ARM Based Device Tree Updates for v4.5

* Add support for Sony Xperia Z
* Updates for Sony Honami board
* Updates for APQ8064 generic platform
* Updates for MSM8974 generic platform
* Add fixed rate oscillators for MSM8960 and APQ8064
* Add documentation for SMSM and SMP2P
* Fixup PMIC compat strings
* Add support for SMEM, RPM/SMD on APQ8084
* Fixup compat on IFC5640

* tag 'qcom-dt-for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux: (24 commits)
  arm: dts: Add support for PMA8084 on APQ8084
  arm: dts: Add RPM/SMD support on APQ8084
  arm: dts: Add APQ8084 SMEM nodes
  ARM: dts: qcom: apq8064-ifc6410 Use hardware flow control for GSBI6
  arm: dts: qcom: apq8064: Add fixed rate on-board oscillators
  ARM: dts: qcom: msm8974: Add i2c8 node
  ARM: dts: qcom: msm8974: Disable wled and move it to honami
  arm: dts: qcom: Add generic PMIC gpio/MPP compat strings
  arm: dts: qcom: Add aliases for PMICs
  arm: dts: qcom: Update ifc6540 compat for qcom boot format
  arm: dts: qcom: Add board clocks
  ARM: dts: qcom: apq8064: Introduce Sony Xperia Z dts
  ARM: dts: qcom: apq8064: Introduce gsbi5 and gsbi5 serial node
  ARM: dts: qcom: apq8064: Declare all pm8921 regulators
  ARM: dts: qcom: apq8064: Add hwmutex and SMEM nodes
  dt-binding: soc: qcom: Introduce qcom, smp2p binding documentation
  dt-binding: soc: qcom: Add Qualcomm SMSM device tree documentation
  devicetree: Add hardware rng entry to qcom-apq8064.dtsi
  ARM: dts: qcom: msm8974-honami: Specify charging parameters
  ARM: dts: qcom: msm8974-honami: Add uSD slot nodes
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

First batch of DT changes for 4.5:
- addition of nodes for sama5d2 & sama5d4
- some fixes for i2c hold time, compatible stings
- addition of a new patform by DENX: the MA5D4 SoM and EVK

* tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
  ARM: at91/dt: sama5d2 Xplained: pmic needs a specific sda hold time
  ARM: at91/dt: sama5d4: update i2c compatible string
  ARM: at91/dt: sama5d4 master clock can run at 200MHz now
  ARM: at91/dt: sama5d2: add watchdog node
  ARM: at91/dt: sama5d4: Add support for DENX MA5D4 SoM and EVK
  ARM: at91/dt: sama5d4: Add pinmux for 8-bit MMC0 bus
  ARM: at91/dt: sama5d4: Fix mmc0 pinmux comments
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'sunxi-dt-for-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt

Allwinner DT changes for 4.5

Allwinner device-tree related patches for the 4.5 merge window.
  * Support for the H3
  * Addition of the RSB to the relevant devices (sun8i, sun9i)
  * Addition of the Video Engine clocks for the older SoCs (sun4i, sun7i)
  * Addition of the DRAM gates for the older SoCs (sun4i, sun7i)
  * Addition of the audio codec to a bunch of boards
  * New board: ICNova SWAC

* tag 'sunxi-dt-for-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (40 commits)
  ARM: dts: sun7i: Olimex A20-SOM-EVB: Enable mmc3 (baseboard SD socket)
  ARM: dts: sun7i: Olimex A20-SOM-EVB: Add LRADC keys
  ARM: dts: sun9i: cubieboard4: Enable Reduced Serial Bus controller
  ARM: dts: sun9i: cubieboard4: Enable consumer IR receiver
  ARM: dts: sun9i: cubieboard4: Enable LEDs
  ARM: dts: sun7i: Add VE (Video Engine) module clock node
  ARM: dts: sun4i: Add VE (Video Engine) module clock node
  ARM: dts: sun8i: Add Orange Pi Plus support
  ARM: dts: sunxi: Add Allwinner H3 DTSI
  ARM: dts: sun7i: Add DRAM gates
  ARM: dts: sun4i: Add DRAM gates
  ARM: dts: sun9i: Add NMI controller device node
  ARM: dts: sun9i: optimus: Enable Reduced Serial Bus controller
  ARM: dts: sun9i: Add Reduced Serial Bus controller device node to A80 dtsi
  ARM: dts: sun9i: optimus: Enable consumer IR receiver
  ARM: dts: sun9i: Add consumer IR receiver device node and pinmux settings
  ARM: dts: sun9i: optimus: Enable LED3
  ARM: dts: sun9i: Add A80 R_PIO pin controller device node
  ARM: dts: sun9i: Add TODO comments for the main and low power clocks
  ARM: dts: sun9i: Add A80 PRCM clocks and reset control nodes
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

arm: Xilinx Zynq dt patches for v4.5

- Various small DT changes, GPIO, slcr, cpu label

* tag 'zynq-dt-for-4.5' of https://github.com/Xilinx/linux-xlnx:
  ARM: dt: zynq: Add labels to cpu nodes to allow overriding OPPs.
  ARM: dts: zynq: describe SLCR as simple-mfd rather than simple-bus
  ARM: dts: zynq: replace gpio-key,wakeup with wakeup-source property
  ARM: zynq: DT: Add interrupt-controller property to GPIO
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'samsung-dt-syscon-restart-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt

Device Tree changes adding necessary nodes for syscon reboot/poweroff
handlers on Exynos boards. The mach-exynos changes must base on top
of this to retain the bisectability of not loosing reboot/poweroff
features.

* tag 'samsung-dt-syscon-restart-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
  ARM: dts: Add syscon-{reboot, poweroff} nodes for exynos5410
  ARM: dts: Add syscon-{reboot, poweroff} nodes for exynos5
  ARM: dts: Add syscon-{reboot, poweroff} nodes for exynos4
  ARM: dts: Add syscon-{reboot, poweroff} nodes for exynos3250
Signed-off-by: Olof Johansson <olof@lixom.net>

The development kit uses a TSC2004 chip attached to I2C3.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The socfpga.dtsi explicitly enabled MMC support, but not all boards are
equiped with an MMC card. There are setups which only have QSPI NOR.
Therefore, disable the MMC support on socfpga.dtsi level and enable it
on per-board basis.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alan Tull <atull@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Thor Thayer <tthayer@altera.com>
Cc: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>

This patchset is the initiation version to try work
for kylin board.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

In general, the sdio/sdmmc is used by the wifi module
and sd card.

let's add the node for these function.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

The pinctrl gpio pull up/down is incorrect since the rk3036 SoCs
can't set the status in the internal.

We should keep the default status for enable the gpio status,
In fact, the pull_none is the disable the gpio pull up/down.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add regulator-allow-bypass property for ldo9.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add regulator-allow-bypass property for ldo1 and ldo2.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add qspi memory mapped region entries for AM43xx based SoCs. Also,
update the binding documents for the controller to document this change.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add qspi memory mapped region entries for DRA7xx based SoCs. Also,
update the binding documents for the controller to document this change.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

For whatever reason, this patch was not applied verbatim and had all
tabs replaced with spaces. Replace them back by a quick sed.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alan Tull <atull@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Thor Thayer <tthayer@altera.com>
Cc: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>

Revert 6f0f6c40b66 ("ARM: dts: Set VAUX1 and VAUX4 on Logic PD Torpedo")
because it It was already done and it's just a duplicate.  See:
2d11961f ("ARM: dts: Set VAUX1 and VAUX4 to 3.0V and 1.8V respectively")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Bindings for the WL1283 Bluetooth was removed from the shared transport
driver in commit c0bd1b9e ("Revert ti-st: add device tree support")
Until we havea better binding, we need to use the platform data to
initialize Bluetooth.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add basic support for Logic PD type 15 display for older development kits.
This uses GPIO for the backlight.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

bluetooth HW is WLS1271 chip connected to UART1.

Device tree modifications:
- Pinmux for UART1.
- Pinmux for bluetooth enable GPIO.

Bluetooth enable GPIO is set to enable during startup by setting the
relevant pinmux pin to pull-up.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add pinmux configuration for DVI/LCD.
Add DRM display driver node with timing configurations for DVI and LCD.
Add I2C GPIOs configurations for DVI and LCD enable.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The I2C GPIO expander (PCA9555) adds 16 GPIOs to the module.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add basic support for the SBC-T335.

CompuLab SBC-T335 is a single baseboard computer.
The SBC-T335 is based on the Texas Instruments Cortex-A8 Sitara AM3354
SoC.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Enable USB0.
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "linux,wakeup" boolean property to enable the wakeup
source, "wakeup-source" is the new standard binding.

This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.

Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Though the keyboard driver for GPIO buttons(gpio-keys) will continue to
check for/support the legacy "gpio-key,wakeup" boolean property to
enable gpio buttons as wakeup source, "wakeup-source" is the new
standard binding.

This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.

Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Switch to use the ti,edma3-tpcc and ti,edma3-tptc binding for the eDMA3 and
enable the DMA even crossbar with ti,am335x-edma-crossbar.
With the new bindings boards can customize and tweak the DMA channel
priority to match their needs. With the new binding the memcpy is safe
to be used since with the old binding it was not possible for a driver
to know which channel is allowed to be used as non HW triggered channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Switch to use the ti,edma3-tpcc and ti,edma3-tptc binding for the eDMA3 and
enable the DMA even crossbar with ti,am335x-edma-crossbar.
With the new bindings boards can customize and tweak the DMA channel
priority to match their needs. With the new binding the memcpy is safe
to be used since with the old binding it was not possible for a driver
to know which channel is allowed to be used as non HW triggered channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use recently SoC-specific compatibility strings in r8a779[01] device trees.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds support for the PMA8084 regulators found on APQ8084
platforms.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>

This patch adds support for RPM and SMD nodes that are present on APQ8084
platforms.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>

This patch adds all the required nodes to support SMEM on APQ8084
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>

GSBI6 UART module is connected to BT chip, which uses
hardware flow control lines. Enable them on SoC side.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>