David Ahern says:

====================
net: vrf: Handle ipv6 multicast and link-local addresses

IPv6 multicast and link-local addresses require special handling by the
VRF driver. Rather than using the VRF device index and full FIB lookups,
packets to/from these addresses should use direct FIB lookups based on
the VRF device table.

Multicast routes do not make sense for the L3 master device directly.
Accordingly, do not add mcast routes for the device, and the VRF driver
should fail attempts to send packets to ipv6 mcast addresses on the
device (e.g, ping6 ff02::1%<vrf> should fail)

With this change connections into and out of a VRF enslaved device work
for multicast and link-local addresses (icmp, tcp, and udp).  e.g.,

1. packets into VM with VRF config:
    ping6 -c3 fe80::e0:f9ff:fe1c:b974%br1
    ping6 -c3 ff02::1%br1
    ssh -6 fe80::e0:f9ff:fe1c:b974%br1

2. packets going out a VRF enslaved device:
    ping6 -c3 fe80::18f8:83ff:fe4b:7a2e%eth1
    ping6 -c3 ff02::1%eth1
    ssh -6 root@fe80::18f8:83ff:fe4b:7a2e%eth1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

IPv6 multicast and link-local addresses require special handling by the
VRF driver:
1. Rather than using the VRF device index and full FIB lookups,
   packets to/from these addresses should use direct FIB lookups based on
   the VRF device table.

2. fail sends/receives on a VRF device to/from a multicast address
   (e.g, make ping6 ff02::1%<vrf> fail)

3. move the setting of the flow oif to the first dst lookup and revert
   the change in icmpv6_echo_reply made in ca254490 ("net: Add VRF
   support to IPv6 stack"). Linklocal/mcast addresses require use of the
   skb->dev.

With this change connections into and out of a VRF enslaved device work
for multicast and link-local addresses work (icmp, tcp, and udp)
e.g.,

1. packets into VM with VRF config:
    ping6 -c3 fe80::e0:f9ff:fe1c:b974%br1
    ping6 -c3 ff02::1%br1

    ssh -6 fe80::e0:f9ff:fe1c:b974%br1

2. packets going out a VRF enslaved device:
    ping6 -c3 fe80::18f8:83ff:fe4b:7a2e%eth1
    ping6 -c3 ff02::1%eth1
    ssh -6 root@fe80::18f8:83ff:fe4b:7a2e%eth1
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

L3 master devices are virtual devices similar to the loopback
device. Link local and multicast routes for these devices do
not make sense. The ipv6 addrconf code already skips adding a
linklocal address; do the same for the mcast route.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow drivers to pass flow arg to functions where the arg is not const
and allow the driver to make updates as needed (eg., setting oif).
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ursula Braun says:

====================
s390: af_iucv patches

here are improvements for af_iucv relaxing the pressure to allocate
big contiguous kernel buffers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When an inbound message is bigger than a page, allocate a paged SKB,
and subsequently use IUCV receive primitive with IPBUFLST flag.
This relaxes the pressure to allocate big contiguous kernel buffers.
Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before introducing paged skbs in the receive path, get rid of the
function `iucv_fragment_skb()` that replaces one large linear skb
with several smaller linear skbs.
Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When an outbound message is bigger than a page, allocate and fill
a paged SKB, and subsequently use IUCV send primitive with IPBUFLST
flag. This relaxes the pressure to allocate big contiguous kernel
buffers.
Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add device tree binding documentation details for Cirrus Logic
CS8900/CS8920 ethernet chip.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add DT support to the Cirrus Logic CS89x0 driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

This function is just ->init(), rename it to make it obvious.

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These should be gone when we removed CONFIG_NET_CLS_POLICE.
We can not totally remove them since they are exposed
to userspace.

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sowmini Varadhan says:

====================
RDS: multiple connection paths for scaling

Today RDS-over-TCP is implemented by demux-ing multiple PF_RDS sockets
between any 2 endpoints (where endpoint == [IP address, port]) over a
single TCP socket between the 2 IP addresses involved. This has the
limitation that it ends up funneling multiple RDS flows over a single
TCP flow, thus the rds/tcp connection is
   (a) upper-bounded to the single-flow bandwidth,
   (b) suffers from head-of-line blocking for the RDS sockets.

Better throughput (for a fixed small packet size, MTU) can be achieved
by having multiple TCP/IP flows per rds/tcp connection, i.e., multipathed
RDS (mprds).  Each such TCP/IP flow constitutes a path for the rds/tcp
connection. RDS sockets will be attached to a path based on some hash
(e.g., of local address and RDS port number) and packets for that RDS
socket will be sent over the attached path using TCP to segment/reassemble
RDS datagrams on that path.

The table below, generated using a prototype that implements mprds,
shows that this is significant for scaling to 40G.  Packet sizes
used were: 8K byte req, 256 byte resp. MTU: 1500.  The parameters for
RDS-concurrency used below are described in the rds-stress(1) man page-
the number listed is proportional to the number of threads at which max
throughput was attained.

  -------------------------------------------------------------------
     RDS-concurrency   Num of       tx+rx K/s (iops)       throughput
     (-t N -d N)       TCP paths
  -------------------------------------------------------------------
        16             1             600K -  700K            4 Gbps
        28             8            5000K - 6000K           32 Gbps
  -------------------------------------------------------------------

FAQ: what is the relation between mprds and mptcp?
  mprds is orthogonal to mptcp. Whereas mptcp creates
  sub-flows for a single TCP connection, mprds parallelizes tx/rx
  at the RDS layer. MPRDS with N paths will allow N datagrams to
  be sent in parallel; each path will continue to send one
  datagram at a time, with sender and receiver keeping track of
  the retransmit and dgram-assembly state based on the RDS header.
  If desired, mptcp can additionally be used to speed up each TCP
  path. That acceleration is orthogonal to the parallelization benefits
  of mprds.

This patch series lays down the foundational data-structures to support
mprds in the kernel. It implements the changes to split up the
rds_connection structure into a common (to all paths) part,
and a per-path rds_conn_path. All I/O workqs are driven from
the rds_conn_path.

Note that this patchset does not (yet) actually enable multipathing
for any of the transports; all transports will continue to use a
single path with the refactored data-structures. A subsequent patchset
will  add the changes to the rds-tcp module to actually use mprds
in rds-tcp.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Refactor rds_conn_destroy() so that the per-path dismantling
is done in rds_conn_path_destroy, and then iterate as needed
over rds_conn_path_destroy().
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit changes rds_conn_shutdown to take a rds_conn_path *
argument, allowing it to shutdown paths other than c_path[0] for
MP-capable transports.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a for() loop in __rds_conn_create to initialize all the
conn_paths, in preparate for MP capable transports.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rds_conn_path_error() is the MP-aware analog of rds_conn_error,
to be used by multipath-capable callers.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit updates the callbacks related to the rds-info command
so that they walk through all the rds_conn_path structures and
report the requested info.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rds_conn_path_connect_if_down() works on the rds_conn_path
that it is passed. Callers who are not t_m_capable may continue
calling rds_conn_connect_if_down, which will invoke
rds_conn_path_connect_if_down() with the default c_path[0].
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit allows rds_send_pong() callers to send back
the rds pong message on some path other than c_path[0] by
passing in a struct rds_conn_path * argument.  It also
removes the last dependency on the #defines in rds_single.h
from send.c
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Explicitly set up rds_conn_path, either from i_conn_path (for
MP capable transpots) or as c_path[0], and use this in
rds_send_drop_to()
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pass a struct rds_conn_path to rds_send_xmit so that MP capable
transports can transmit packets on something other than c_path[0].
The eventual goal for MP capable transports is to hash the rds
socket to a path based on the bound local address/port, and use
this path as the argument to rds_send_xmit()
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pass the rds_conn_path to rds_send_queue_rm, and use it to initialize
the i_conn_path field in struct rds_incoming. This commit also makes
rds_send_queue_rm() MP capable, because it now takes locks
specific to the rds_conn_path passed in, instead of defaulting to
the c_path[0] based defines from rds_single_path.h
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The only caller of rds_send_get_message() was
rds_iw_send_cq_comp_handler() which was removed as part of
commit dcdede04 ("RDS: Drop stale iWARP RDMA transport"),
so remove rds_send_get_message() for the same reason.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rds_send_path_drop_acked() is the path-specific version of
rds_send_drop_acked() to be invoked by MP capable callers.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rds_send_path_reset() is the path specific version of rds_send_reset()
intended for MP capable callers.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

t_mp_capable transports can use rds_inc_path_init to initialize
all fields in struct rds_incoming, including the i_conn_path.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Transports that are t_mp_capable should set the rds_conn_path
on which the datagram was recived in the ->i_conn_path field
of struct rds_incoming.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The t_mp_capable bit will be used in the core rds module
to support multipathing logic when the transport supports it.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for multipath RDS, split the rds_connection
structure into a base structure, and a per-path struct rds_conn_path.
The base structure tracks information and locks common to all
paths. The workqs for send/recv/shutdown etc are tracked per
rds_conn_path. Thus the workq callbacks now work with rds_conn_path.

This commit allows for one rds_conn_path per rds_connection, and will
be extended into multiple conn_paths in  subsequent commits.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure that dctcp_get_info() returns only the size of the
info->dctcp struct that it zeroes out and fills in. Previously it had
been returning the size of the enclosing tcp_cc_info union,
sizeof(*info).  There is no problem yet, but that union that may one
day be larger than struct tcp_dctcp_info, in which case the
TCP_CC_INFO code might accidentally copy uninitialized bytes from the
stack.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'rxrpc-rewrite-20160613' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs

David Howells says:

====================
rxrpc: Rename rxrpc source files

Here's the next part of the AF_RXRPC rewrite.  In this set I rename some of
the files in the net/rxrpc/ directory and adjust the Makefile and
ar-internal.h to reflect the changes.

The aim is twofold:

 (1) Remove the "ar-" prefix on those files that have it as it's not really
     useful, especially now that I'm building rxkad in.

 (2) To aid splitting the local, peer, connection and call handling code
     into separate files for object and event handling in future patches by
     making it easier to come up with new filenames.

There are two commits:

 (1) The first commit does a bunch of renames of .c files and alters the
     Makefile.  ar-internal.h isn't renamed at this time to avoid having to
     change the contents of the files being renamed.

 (2) The second commit changes the section label comments in ar-internal.h
     to reflect the changed filenames and reorders the file so that the
     sections are back in filename order.

The patches can be found here also:

	http://git.kernel.org/cgit/linux/kernel/git/dhowells/linux-fs.git/log/?h=rxrpc-rewrite

Tagged thusly:

	git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs.git
	rxrpc-rewrite-20160613
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

After the patchset about adding support of ACPI (commit id is 63434888)
being applied, HNS does not depend on OF. It depends on OF or ACPI, so
the Kconfig file needs to be updated.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hayes Wang says:

====================
r8152: code adjustment for PHY

These patches are for adjusting the code about PHY and setting speed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The user may change the speed. Use it to replace the default one.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move calling set_speed() from open() to rtl_hw_phy_work_func_t().
Then, we would set the default speed only for first initialization
or after resuming.

Besides, the set_speed() could handle the flag of PHY_RESET which
would be set in rtl_ops.hw_phy_cfg().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the settings of PHY to a work queue and schedule it after
rtl_ops.init().

There are some reasons for this. First, the settings are only
needed for the first time initialization or after the power
down occurs.

Second, the settings are independent with the others.

Last, the settings may take more time than the others. Leave
they in probe() or open() may delay the following flows.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When skip_sw is set and hardware fails to apply filter, return error to
user. This will make error propagation logic similar to the one
currently used in u32 classifier.
Also, changed code to use tc_skip_sw() utility function.
Signed-off-by: Amir Vadai <amirva@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Updates for net-next.

-Add default VLAN support for VFs.
-Add NPAR (NIC partioning) support.
-Add support for new device 5731x and 5741x. GRO logic is different.
-Support new ETHTOOL_{G|S}LINKSETTINGS.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>