This pull request brings in several fixes for drm-next, mostly for
HDMI.

* tag 'drm-vc4-next-2016-10-06' of https://github.com/anholt/linux:
  drm/vc4: Add support for double-clocked modes.
  drm/vc4: Set up the AVI and SPD infoframes.
  drm/vc4: Fix support for interlaced modes on HDMI.
  drm/vc4: Increase timeout for HDMI_SCHEDULER_CONTROL changes.
  drm/vc4: Fall back to using an EDID probe in the absence of a GPIO.
  drm/vc4: Enable limited range RGB output on HDMI with CEA modes.
  drm/vc4: Fix races when the CS reads from render targets.
  drm/vc4: cleanup with list_first_entry_or_null()

Now that we have infoframes to report the pixel repeat flag, we can
start using it.  Fixes locking the 720x480i and 720x576i modes on my
Dell 2408WFP.  Like the 1920x1080i case, they don't fit properly on
the screen, though.
Signed-off-by: Eric Anholt <eric@anholt.net>

Fixes a purple bar on the left side of the screen with my Dell
2408WFP.  It will also be required for supporting the double-clocked
video modes.
Signed-off-by: Eric Anholt <eric@anholt.net>

We really do need to be using the halved V fields.  I had been
confused by the code I was using as a reference because it stored
halved vsync fields but not halved vdisplay, so it looked like I only
needed to divide vdisplay by 2.

This reverts part of Mario's timestamping fixes that prevented
CRTC_HALVE_V from applying, and instead adjusts the timestamping code
to not use the crtc field in that case.

Fixes locking of 1920x1080x60i on my Dell 2408WFP.  There are black
bars on the top and bottom, but I suspect that might be an
under/overscan flags problem as opposed to video timings.
Signed-off-by: Eric Anholt <eric@anholt.net>

Fixes occasional debug spew at boot when connected directly through
HDMI, and probably confusing the HDMI state machine when we go trying
to poke registers for the enable sequence too soon.
Signed-off-by: Eric Anholt <eric@anholt.net>

On Pi0/1/2, we use an external GPIO line for hotplug detection, since
the HDMI_HOTPLUG register isn't connected to anything.  However, with
the Pi3 the HPD GPIO line has moved off to a GPIO expander that will
be tricky to get to (the firmware is constantly polling the expander
using i2c0, so we'll need to coordinate with it).

As a stop-gap, if we don't have a GPIO line, use an EDID probe to
detect connection.  Fixes HDMI display on the pi3.
Signed-off-by: Eric Anholt <eric@anholt.net>

Fixes broken grayscale ramps on many HDMI monitors, where large areas
at the ends of the ramp would all appear as black or white.
Signed-off-by: Eric Anholt <eric@anholt.net>

With the introduction of bin/render pipelining, the previous job may
not be completed when we start binning the next one.  If the previous
job wrote our VBO, IB, or CS textures, then the binning stage might
get stale or uninitialized results.

Fixes the major rendering failure in glmark2 -b terrain.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: ca26d28b ("drm/vc4: improve throughput by pipelining binning and rendering jobs")
Cc: stable@vger.kernel.org

The combo of list_empty() check and return list_first_entry()
can be replaced with list_first_entry_or_null().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Eric Anholt <eric@anholt.net>

Before commit a3257256 ("drm: Lobotomize set_busid nonsense for !pci
drivers"), several DRM drivers for platform devices used to expose an
explicit "drm_driver.set_busid" callback, invariably backed by
drm_platform_set_busid().

Commit a3257256 removed drm_platform_set_busid(), along with the
referring .set_busid field initializations. This was justified because
interchangeable functionality had been implemented in drm_dev_alloc() /
drm_dev_init(), which DRM_IOCTL_SET_VERSION would rely on going forward.

However, commit a3257256 also removed drm_virtio_set_busid(), for
which the same consolidation was not appropriate: this .set_busid callback
had been implemented with drm_pci_set_busid(), and not
drm_platform_set_busid(). The error regressed Xorg/xserver on QEMU's
"virtio-vga" card; the drmGetBusid() function from libdrm would no longer
return stable PCI identifiers like "pci:0000:00:02.0", but rather unstable
platform ones like "virtio0".

Reinstate drm_virtio_set_busid() with judicious use of

  git checkout -p a3257256^ -- drivers/gpu/drm/virtio

Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Joachim Frieben <jfrieben@hotmail.com>
Cc: stable@vger.kernel.org # v4.8
Reported-by: Joachim Frieben <jfrieben@hotmail.com>
Fixes: a3257256
Ref: https://bugzilla.redhat.com/show_bug.cgi?id=1366842Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

I screwed up rebasing of my patch in

commit 43968d7b
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Wed Sep 21 10:59:24 2016 +0200

    drm: Extract drm_plane.[hc]

which meant on error paths drm_crtc_vblank_put could be called without
a get, leading to an underrun of the refcount.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98020Reported-and-tested-by: Andy Furniss <adf.lists@gmail.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161003082827.11586-1-daniel.vetter@ffwll.chSigned-off-by: Dave Airlie <airlied@redhat.com>

Commit 43968d7b ("drm: Extract drm_plane.[hc]") was not the simple
cut'n'paste we presumed, somehow it introduced a leak of the page flip
target's framebuffer.

Fixes: 43968d7b ("drm: Extract drm_plane.[hc]")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160928222500.11827-1-chris@chris-wilson.co.ukSigned-off-by: Dave Airlie <airlied@redhat.com>

Merge branch 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-next

This pull request includes,
    - Code refactoring on HDMI DDC and PHY.
    - Regression fixup on deadlock issue with G2D pm integration.
    - Fixup on page fault issue with wait_for_vblank mechianism specific to Exynos drm.
    - And some cleanups.

* 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
  drm/exynos: g2d: simplify g2d_free_runqueue_node()
  drm/exynos: g2d: use autosuspend mode for PM runtime
  drm/exynos: g2d: wait for engine to finish
  drm/exynos: g2d: remove runqueue nodes in g2d_{close,remove}()
  drm/exynos: g2d: move PM management to runqueue worker
  Revert "drm/exynos: g2d: fix system and runtime pm integration"
  drm/exynos: use drm core to handle page-flip event
  drm/exynos: mark exynos_dp_crtc_clock_enable() static
  drm/exynos/fimd: add clock rate checking
  drm/exynos: fix pending update handling
  drm/exynos/vidi: use timer for vblanks instead of sleeping worker
  drm/exynos: g2d: beautify probing message
  drm/exynos: mixer: simplify loop in vp_win_reset()
  drm/exynos: mixer: convert booleans to flags in mixer context
  gpu: drm: exynos_hdmi: Remove duplicate initialization of regulator bulk consumer
  gpu: drm: exynos_hdmi: Move PHY logic into single function
  gpu: drm: exynos_hdmi: Move DDC logic into single function

The function is never called with zero 'runqueue_node'.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

The runqueue worker currently issues a get() when a new
node is processed, and a put() once a node is completed.

The corresponding suspend and resume calls currently only
do clock gating, but with the upcoming introduction of
IOMMU runpm also the corresponding IOMMU domain gets
enabled (for get()) and disabled (for put()). This
introduces performance regressions with we mitigate here.

Switch PM runtime to autosuspend, such that clock gating
and IOMMU control only happens when the engine is idle for
a 'long' time.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

While the engine works on a runqueue node it does memory access to
the buffers associated with that node.
Make sure that the engine is idle when g2d_close() and/or
g2d_remove() are called, i.e. buffer associated with the process (for
g2d_close()), or all buffers (for g2d_remove()) can be safely be
unmapped.

We have to take into account that the engine might be in an undefined
state, i.e. it hangs and doesn't become idle. In this case, we issue
a hardware reset to return the hardware and the driver context into a
proper state.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

The driver might be closed (and/or removed) while there are still
nodes queued for processing.
Make sure to remove these nodes, which means all of them in
the case of g2d_remove() and only those belonging to the
corresponding process in g2d_close().
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Do all pm_runtime_{get,put}() calls in the runqueue worker.
Also keep track of the engine's idle/busy state.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

This reverts commit b05984e2.

The change, i.e. merging the sleep and runpm operations, produces
a deadlock situation:
(1) exynos_g2d_exec_ioctl() prepares a runqueue node and
    calls g2d_exec_runqueue()
(2) g2d_exec_runqueue() calls g2d_dma_start() which gets
    runtime PM sync
(3) runtime PM core calls g2d_runtime_resume()
(4) g2d_runtime_resume() calls g2d_exec_runqueue(), which
    loops back to (2)

Due to mutexes that are in place, a deadlock situation is created.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Exynos DRM framework handled page-flip event with custom code.
The patch replaces it with drm-core vblank queue.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

We get 1 warning when building kernel with W=1:
drivers/gpu/drm/exynos/exynos_dp.c:46:5: warning: no previous prototype for 'exynos_dp_crtc_clock_enable' [-Wmissing-prototypes]

In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
So this patch marks it 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

In case of some platforms fimd clocks can be configured to
very low values, as a result refresh rate can be very low and
driver/drm-core will timeout waiting for vblanks, it will result
in premature removal of framebuffers and will cause oopses.
The patch adds atomic_check callback to fimd to prevent setting
such modes.
Reported-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Exynos DRM devices update their registers at vblank time. Exynos-DRM uses
custom mechanism to wait for vblank. This mechanism is error prone -
variables are not updated atomically. As a result in certain circumstances
user space can try to free buffers which are still in use by hardware,
in such cases IOMMU can throw OOPS.
The patch instead of fixing the mechanism replaces it with drm core helper.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

VIDI driver uses fake vblank handler to generate vblank events.
It was implemented using worker which slept for vblank time, additionally
it did not work if there were no page flips. The patch replaces it with
timer, uses drm_crtc_vblank_(on|off) helpers to manage it and fixes
behavior for non-page-flip cases.
This change allows further improvements of vblank in exynos-drm framework.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Apply some 'make-up' in g2d_probe().
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

A simple while loop should do the same here.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

The mixer context struct already has a 'flags' field, so
we can use it to store the 'interlace', 'vp_enabled' and
'has_sclk' booleans.
We use the non-atomic helper functions to access these bits.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

The helper, devm_regulator_bulk_get() initializes the consumer as NULL,
so this code can be ignored.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Paring DT properties and getting PHY IO (memory mapped or I2C) in one
function.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Paring DT properties and getting the I2C adapter in one function.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Some additional fixes for 4.9:
- The rest of Christian's GTT rework which fixes a long standing bug
  in the GPUVM code among other things
- Changes to the pci shutdown callbacks for certain hypervisors
- Fix hpd interrupt storms on eDP panels which have the hpd interrupt
  enabled by the bios
- misc cleanups and bug fixes

* 'drm-next-4.9' of git://people.freedesktop.org/~agd5f/linux: (33 commits)
  drm/radeon: always apply pci shutdown callbacks
  drm/amdgpu: always apply pci shutdown callbacks (v2)
  drm/amdgpu: improve VM PTE trace points
  drm/amdgpu: fix GART_DEBUGFS define
  drm/amdgpu: free userptrs even if GTT isn't bound
  drm/amd/amdgpu: Various cleanups for DCEv6
  drm/amdgpu: fix BO move offsets
  drm/amdgpu: fix amdgpu_move_blit on 32bit systems
  drm/amdgpu: fix gtt_mgr bo's offset
  drm/amdgpu: fix initializing the VM BO shadow
  drm/amdgpu: fix initializing the VM last eviction counter
  drm/amdgpu: cleanup VM shadow BO unreferencing
  drm/amdgpu: allocate GTT space for shadow VM page tables
  drm/amdgpu: rename all rbo variable to abo v2
  drm/amdgpu: remove unused member from struct amdgpu_bo
  drm/amdgpu: add a custom GTT memory manager v2
  drm/amdgpu/dce6: disable hpd on local panels
  drm/amdgpu/dce8: disable hpd on local panels
  drm/amdgpu/dce11: disable hpd on local panels
  drm/amdgpu/dce10: disable hpd on local panels
  ...

drm/tegra: Changes for v4.9-rc1

One bugfix that avoids overwriting the Y plane base address when
displaying buffers with one of the YUV/YVU formats.

* tag 'drm/tegra/for-4.9-rc1' of git://anongit.freedesktop.org/tegra/linux:
  drm/tegra: Fix window[0] base address corruption

drm/panel: Changes for v4.9-rc1

Adds support for one more panel to the simple-panel driver, fixes up a
couple of delays and flags for existing panels and finally adds a new
driver for the DSI panel found on Nexus 7 devices.

* tag 'drm/panel/for-4.9-rc1' of git://anongit.freedesktop.org/tegra/linux:
  drm/panel: Add JDI LT070ME05000 WUXGA DSI Panel
  dt-bindings: Add JDI LT070ME05000 panel bindings
  drm/panel: simple: Fix bus_format for the Olimex LCD-OLinuXino-4.3TS
  drm/panel: simple-panel: Add delay timings for Starry KR122EA0SRA
  drm/panel: simple: Fix bus flags for Ortustech com43h4m85ulc
  drm/panel: simple: Add Innolux G101ICE-L01 panel
  drm/panel: simple: Add delay timing for Sharp LQ123P1JX31
  drm/dsi: Implement DCS set/get display brightness
  drm/dsi: Order DCS helpers by command code

We can't properly detect all hypervisors and we
need this to properly tear down the hardware.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

We can't properly detect all hypervisors and we
need this to properly tear down the hardware.

v2: trivial warning fix
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Use a separate one for the copy operation and
log all the interesting parameters.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Obviously missed during the rename.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This fixes a memory leak since binding GTT only on demand.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

It's pretty pointless to get the offset first and then initialize it.

Should fix issues with the new GTT manager.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>