1. 06 Jul, 2017 12 commits
  2. 05 Jul, 2017 26 commits
    • Linus Torvalds's avatar
      Cavium CNN55XX: fix broken default Kconfig entry · b4b8cbf6
      Linus Torvalds authored
      Every developer always thinks that _their_ code is so special and
      magical that it should be enabled by default.
      
      And most of them are completely and utterly wrong.  That's definitely
      the case when you write a specialty driver for a very unsual "security
      processor". It does *not* get to mark itself as "default m".
      
      If you solve world hunger, and make a driver that cures people of
      cancer, by all means enable it by default.  But afaik, the Cavium
      CNN55XX does neither.
      Signed-off-by: default avatarLinus Torvalds <torvalds@linux-foundation.org>
      b4b8cbf6
    • Linus Torvalds's avatar
      Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next · 5518b69b
      Linus Torvalds authored
      Pull networking updates from David Miller:
       "Reasonably busy this cycle, but perhaps not as busy as in the 4.12
        merge window:
      
         1) Several optimizations for UDP processing under high load from
            Paolo Abeni.
      
         2) Support pacing internally in TCP when using the sch_fq packet
            scheduler for this is not practical. From Eric Dumazet.
      
         3) Support mutliple filter chains per qdisc, from Jiri Pirko.
      
         4) Move to 1ms TCP timestamp clock, from Eric Dumazet.
      
         5) Add batch dequeueing to vhost_net, from Jason Wang.
      
         6) Flesh out more completely SCTP checksum offload support, from
            Davide Caratti.
      
         7) More plumbing of extended netlink ACKs, from David Ahern, Pablo
            Neira Ayuso, and Matthias Schiffer.
      
         8) Add devlink support to nfp driver, from Simon Horman.
      
         9) Add RTM_F_FIB_MATCH flag to RTM_GETROUTE queries, from Roopa
            Prabhu.
      
        10) Add stack depth tracking to BPF verifier and use this information
            in the various eBPF JITs. From Alexei Starovoitov.
      
        11) Support XDP on qed device VFs, from Yuval Mintz.
      
        12) Introduce BPF PROG ID for better introspection of installed BPF
            programs. From Martin KaFai Lau.
      
        13) Add bpf_set_hash helper for TC bpf programs, from Daniel Borkmann.
      
        14) For loads, allow narrower accesses in bpf verifier checking, from
            Yonghong Song.
      
        15) Support MIPS in the BPF selftests and samples infrastructure, the
            MIPS eBPF JIT will be merged in via the MIPS GIT tree. From David
            Daney.
      
        16) Support kernel based TLS, from Dave Watson and others.
      
        17) Remove completely DST garbage collection, from Wei Wang.
      
        18) Allow installing TCP MD5 rules using prefixes, from Ivan
            Delalande.
      
        19) Add XDP support to Intel i40e driver, from Björn Töpel
      
        20) Add support for TC flower offload in nfp driver, from Simon
            Horman, Pieter Jansen van Vuuren, Benjamin LaHaise, Jakub
            Kicinski, and Bert van Leeuwen.
      
        21) IPSEC offloading support in mlx5, from Ilan Tayari.
      
        22) Add HW PTP support to macb driver, from Rafal Ozieblo.
      
        23) Networking refcount_t conversions, From Elena Reshetova.
      
        24) Add sock_ops support to BPF, from Lawrence Brako. This is useful
            for tuning the TCP sockopt settings of a group of applications,
            currently via CGROUPs"
      
      * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1899 commits)
        net: phy: dp83867: add workaround for incorrect RX_CTRL pin strap
        dt-bindings: phy: dp83867: provide a workaround for incorrect RX_CTRL pin strap
        cxgb4: Support for get_ts_info ethtool method
        cxgb4: Add PTP Hardware Clock (PHC) support
        cxgb4: time stamping interface for PTP
        nfp: default to chained metadata prepend format
        nfp: remove legacy MAC address lookup
        nfp: improve order of interfaces in breakout mode
        net: macb: remove extraneous return when MACB_EXT_DESC is defined
        bpf: add missing break in for the TCP_BPF_SNDCWND_CLAMP case
        bpf: fix return in load_bpf_file
        mpls: fix rtm policy in mpls_getroute
        net, ax25: convert ax25_cb.refcount from atomic_t to refcount_t
        net, ax25: convert ax25_route.refcount from atomic_t to refcount_t
        net, ax25: convert ax25_uid_assoc.refcount from atomic_t to refcount_t
        net, sctp: convert sctp_ep_common.refcnt from atomic_t to refcount_t
        net, sctp: convert sctp_transport.refcnt from atomic_t to refcount_t
        net, sctp: convert sctp_chunk.refcnt from atomic_t to refcount_t
        net, sctp: convert sctp_datamsg.refcnt from atomic_t to refcount_t
        net, sctp: convert sctp_auth_bytes.refcnt from atomic_t to refcount_t
        ...
      5518b69b
    • Linus Torvalds's avatar
      Merge branch 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6 · 8ad06e56
      Linus Torvalds authored
      Pull crypto updates from Herbert Xu:
       "Algorithms:
         - add private key generation to ecdh
      
        Drivers:
         - add generic gcm(aes) to aesni-intel
         - add SafeXcel EIP197 crypto engine driver
         - add ecb(aes), cfb(aes) and ecb(des3_ede) to cavium
         - add support for CNN55XX adapters in cavium
         - add ctr mode to chcr
         - add support for gcm(aes) to omap"
      
      * 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (140 commits)
        crypto: testmgr - Reenable sha1/aes in FIPS mode
        crypto: ccp - Release locks before returning
        crypto: cavium/nitrox - dma_mapping_error() returns bool
        crypto: doc - fix typo in docs
        Documentation/bindings: Document the SafeXel cryptographic engine driver
        crypto: caam - fix gfp allocation flags (part II)
        crypto: caam - fix gfp allocation flags (part I)
        crypto: drbg - Fixes panic in wait_for_completion call
        crypto: caam - make of_device_ids const.
        crypto: vmx - remove unnecessary check
        crypto: n2 - make of_device_ids const
        crypto: inside-secure - use the base_end pointer in ring rollback
        crypto: inside-secure - increase the batch size
        crypto: inside-secure - only dequeue when needed
        crypto: inside-secure - get the backlog before dequeueing the request
        crypto: inside-secure - stop requeueing failed requests
        crypto: inside-secure - use one queue per hw ring
        crypto: inside-secure - update the context and request later
        crypto: inside-secure - align the cipher and hash send functions
        crypto: inside-secure - optimize DSE bufferability control
        ...
      8ad06e56
    • Linus Torvalds's avatar
      Merge tag 'gcc-plugins-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux · 59005b0c
      Linus Torvalds authored
      Pull GCC plugin updates from Kees Cook:
       "The big part is the randstruct plugin infrastructure.
      
        This is the first of two expected pull requests for randstruct since
        there are dependencies in other trees that would be easier to merge
        once those have landed. Notably, the IPC allocation refactoring in
        -mm, and many trivial merge conflicts across several trees when
        applying the __randomize_layout annotation.
      
        As a result, it seemed like I should send this now since it is
        relatively self-contained, and once the rest of the trees have landed,
        send the annotation patches. I'm expecting the final phase of
        randstruct (automatic struct selection) will land for v4.14, but if
        its other tree dependencies actually make it for v4.13, I can send
        that merge request too.
      
        Summary:
      
        - typo fix in Kconfig (Jean Delvare)
      
        - randstruct infrastructure"
      
      * tag 'gcc-plugins-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
        ARM: Prepare for randomized task_struct
        randstruct: Whitelist NIU struct page overloading
        randstruct: Whitelist big_key path struct overloading
        randstruct: Whitelist UNIXCB cast
        randstruct: Whitelist struct security_hook_heads cast
        gcc-plugins: Add the randstruct plugin
        Fix English in description of GCC_PLUGIN_STRUCTLEAK
        compiler: Add __designated_init annotation
        gcc-plugins: Detail c-common.h location for GCC 4.6
      59005b0c
    • Linus Torvalds's avatar
      Merge tag 'pstore-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux · 2cc7b4ca
      Linus Torvalds authored
      Pull pstore updates from Kees Cook:
       "Various fixes and tweaks for the pstore subsystem.
      
        Highlights:
      
         - use memdup_user() instead of open-coded copies (Geliang Tang)
      
         - fix record memory leak during initialization (Douglas Anderson)
      
         - avoid confused compressed record warning (Ankit Kumar)
      
         - prepopulate record timestamp and remove redundant logic from
           backends"
      
      * tag 'pstore-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
        powerpc/nvram: use memdup_user
        pstore: use memdup_user
        pstore: Fix format string to use %u for record id
        pstore: Populate pstore record->time field
        pstore: Create common record initializer
        efi-pstore: Refactor erase routine
        pstore: Avoid potential infinite loop
        pstore: Fix leaked pstore_record in pstore_get_backend_records()
        pstore: Don't warn if data is uncompressed and type is not PSTORE_TYPE_DMESG
      2cc7b4ca
    • Linus Torvalds's avatar
      Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security · e24dd9ee
      Linus Torvalds authored
      Pull security layer updates from James Morris:
      
       - a major update for AppArmor. From JJ:
      
           * several bug fixes and cleanups
      
           * the patch to add symlink support to securityfs that was floated
             on the list earlier and the apparmorfs changes that make use of
             securityfs symlinks
      
           * it introduces the domain labeling base code that Ubuntu has been
             carrying for several years, with several cleanups applied. And it
             converts the current mediation over to using the domain labeling
             base, which brings domain stacking support with it. This finally
             will bring the base upstream code in line with Ubuntu and provide
             a base to upstream the new feature work that Ubuntu carries.
      
           * This does _not_ contain any of the newer apparmor mediation
             features/controls (mount, signals, network, keys, ...) that
             Ubuntu is currently carrying, all of which will be RFC'd on top
             of this.
      
       - Notable also is the Infiniband work in SELinux, and the new file:map
         permission. From Paul:
      
            "While we're down to 21 patches for v4.13 (it was 31 for v4.12),
             the diffstat jumps up tremendously with over 2k of line changes.
      
             Almost all of these changes are the SELinux/IB work done by
             Daniel Jurgens; some other noteworthy changes include a NFS v4.2
             labeling fix, a new file:map permission, and reporting of policy
             capabilities on policy load"
      
         There's also now genfscon labeling support for tracefs, which was
         lost in v4.1 with the separation from debugfs.
      
       - Smack incorporates a safer socket check in file_receive, and adds a
         cap_capable call in privilege check.
      
       - TPM as usual has a bunch of fixes and enhancements.
      
       - Multiple calls to security_add_hooks() can now be made for the same
         LSM, to allow LSMs to have hook declarations across multiple files.
      
       - IMA now supports different "ima_appraise=" modes (eg. log, fix) from
         the boot command line.
      
      * 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (126 commits)
        apparmor: put back designators in struct initialisers
        seccomp: Switch from atomic_t to recount_t
        seccomp: Adjust selftests to avoid double-join
        seccomp: Clean up core dump logic
        IMA: update IMA policy documentation to include pcr= option
        ima: Log the same audit cause whenever a file has no signature
        ima: Simplify policy_func_show.
        integrity: Small code improvements
        ima: fix get_binary_runtime_size()
        ima: use ima_parse_buf() to parse template data
        ima: use ima_parse_buf() to parse measurements headers
        ima: introduce ima_parse_buf()
        ima: Add cgroups2 to the defaults list
        ima: use memdup_user_nul
        ima: fix up #endif comments
        IMA: Correct Kconfig dependencies for hash selection
        ima: define is_ima_appraise_enabled()
        ima: define Kconfig IMA_APPRAISE_BOOTPARAM option
        ima: define a set of appraisal rules requiring file signatures
        ima: extend the "ima_policy" boot command line to support multiple policies
        ...
      e24dd9ee
    • Linus Torvalds's avatar
      Merge branch 'stable-4.13' of git://git.infradead.org/users/pcmoore/audit · 7391786a
      Linus Torvalds authored
      Pull audit updates from Paul Moore:
       "Things are relatively quiet on the audit front for v4.13, just five
        patches for a total diffstat of 102 lines.
      
        There are two patches from Richard to consistently record the POSIX
        capabilities and add the ambient capability information as well.
      
        I also chipped in two patches to fix a race condition with the auditd
        tracking code and ensure we don't skip sending any records to the
        audit multicast group.
      
        Finally a single style fix that I accepted because I must have been in
        a good mood that day.
      
        Everything passes our test suite, and should be relatively harmless,
        please merge for v4.13"
      
      * 'stable-4.13' of git://git.infradead.org/users/pcmoore/audit:
        audit: make sure we never skip the multicast broadcast
        audit: fix a race condition with the auditd tracking code
        audit: style fix
        audit: add ambient capabilities to CAPSET and BPRM_FCAPS records
        audit: unswing cap_* fields in PATH records
      7391786a
    • Linus Torvalds's avatar
      Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk · eed1fc87
      Linus Torvalds authored
      Pull printk updates from Petr Mladek:
      
       - Store printk() messages into the main log buffer directly even in NMI
         when the lock is available. It is the best effort to print even large
         chunk of text. It is handy, for example, when all ftrace messages are
         printed during the system panic in NMI.
      
       - Add missing annotations to calm down compiler warnings
      
      * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk:
        printk: add __printf attributes to internal functions
        printk: Use the main logbuf in NMI when logbuf_lock is available
      eed1fc87
    • David S. Miller's avatar
      Merge branch 'phy-dp83867-workaround-incorrect-RX_CTRL-pin-strap' · 0e725822
      David S. Miller authored
      Sekhar Nori says:
      
      ====================
      net: phy: dp83867: workaround incorrect RX_CTRL pin strap
      
      This patch series adds workaround for incorrect RX_CTRL pin strap
      setting that can be found on some TI boards.
      
      This is required to be complaint to PHY datamanual specification.
      ====================
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      0e725822
    • Murali Karicheri's avatar
      net: phy: dp83867: add workaround for incorrect RX_CTRL pin strap · 37144476
      Murali Karicheri authored
      The data manual for DP83867IR/CR, SNLS484E[1], revised march 2017,
      advises that strapping RX_DV/RX_CTRL pin in mode 1 and 2 is not
      supported (see note below Table 5 (4-Level Strap Pins)).
      
      There are some boards which have the pin strapped this way and need
      software workaround suggested by the data manual. Bit[7] of
      Configuration Register 4 (address 0x0031) must be cleared to 0. This
      ensures proper operation of the PHY.
      
      Implement driver support for device-tree property meant to advertise
      the wrong strapping.
      
      [1] http://www.ti.com/lit/ds/snls484e/snls484e.pdfSigned-off-by: default avatarMurali Karicheri <m-karicheri2@ti.com>
      [nsekhar@ti.com: rebase to mainline, code simplification]
      Signed-off-by: default avatarSekhar Nori <nsekhar@ti.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      37144476
    • Murali Karicheri's avatar
      dt-bindings: phy: dp83867: provide a workaround for incorrect RX_CTRL pin strap · 908a7733
      Murali Karicheri authored
      The data manual for DP83867IR/CR, SNLS484E[1], revised march 2017,
      advises that strapping RX_DV/RX_CTRL pin in mode 1 and 2 is not
      supported (see note below Table 5 (4-Level Strap Pins)).
      
      It further advises that if a board has this pin strapped in mode 1 and
      mode 2, then to ensure proper operation of the PHY, a software workaround
      must be implemented.
      
      Since it is not possible to detect in software if RX_DV/RX_CTRL pin is
      incorrectly strapped, add a device-tree property for the board to
      advertise this and allow corrective action in software.
      
      [1] http://www.ti.com/lit/ds/snls484e/snls484e.pdfSigned-off-by: default avatarMurali Karicheri <m-karicheri2@ti.com>
      [nsekhar@ti.com: rebase to mainline, split documentation into separate patch]
      Signed-off-by: default avatarSekhar Nori <nsekhar@ti.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      908a7733
    • David S. Miller's avatar
      Merge branch 'cxgb4-ptp' · a778427e
      David S. Miller authored
      Atul Gupta says:
      
      ====================
      cxgb4: Add PTP Hardware Clock (PHC) support
      
      V4:
      	Splitting the patch again
      V3:
              Releasing lock in the exit paths
      V2:
              Splitting the patch
      ====================
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      a778427e
    • Atul Gupta's avatar
      cxgb4: Support for get_ts_info ethtool method · c3ff08eb
      Atul Gupta authored
      Cc: Richard Cochran <richardcochran@gmail.com>
      Signed-off-by: default avatarAtul Gupta <atul.gupta@chelsio.com>
      Signed-off-by: default avatarGanesh Goudar <ganeshgr@chelsio.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      c3ff08eb
    • Atul Gupta's avatar
      cxgb4: Add PTP Hardware Clock (PHC) support · 9c33e420
      Atul Gupta authored
      Add PTP IEEE-1588 support and make it accessible via PHC subsystem.
      The functionality is enabled for T5/T6 adapters. Driver interfaces with
      Firmware to program and adjust the clock offset.
      
      Cc: Richard Cochran <richardcochran@gmail.com>
      Signed-off-by: default avatarAtul Gupta <atul.gupta@chelsio.com>
      Signed-off-by: default avatarGanesh Goudar <ganeshgr@chelsio.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      9c33e420
    • Atul Gupta's avatar
      cxgb4: time stamping interface for PTP · a4569504
      Atul Gupta authored
      Supports hardware and software time stamping via the
      Linux SO_TIMESTAMPING socket option.
      
      Cc: Richard Cochran <richardcochran@gmail.com>
      Signed-off-by: default avatarAtul Gupta <atul.gupta@chelsio.com>
      Signed-off-by: default avatarGanesh Goudar <ganeshgr@chelsio.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      a4569504
    • David S. Miller's avatar
      Merge branch 'nfp-port-enumeration-change-and-FW-ABI-adjustment' · 97d731d8
      David S. Miller authored
      Jakub Kicinski says:
      
      ====================
      nfp: port enumeration change and FW ABI adjustment
      
      This set changes the way ports are numbered internally to avoid MAC address
      changes and invalid link information when breakout is configured.  Second
      patch gets rid of old way of looking up MAC addresses in device information
      which caused all this confusion.
      
      Patch 3 is a small adjustment to the new FW ABI version we introduced in
      this release cycle.
      ====================
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      97d731d8
    • Jakub Kicinski's avatar
      nfp: default to chained metadata prepend format · 64a919a9
      Jakub Kicinski authored
      ABI 4.x introduced the chained metadata format and made it the
      only one possible.  There are cases, however, where the old
      format is preferred - mostly to make interoperation with VFs
      using ABI 3.x easier for the datapath.  In ABI 5.x we allowed
      for more flexibility by selecting the metadata format based
      on capabilities.  The default was left to non-chained.
      
      In case of fallback traffic, there is no capability telling the
      driver there may be chained metadata.  With a very stripped-
      -down FW the default old metadata format would be selected
      making the driver drop all fallback traffic.
      
      This patch changes the default selection in the driver. It
      should not hurt with old firmwares, because if they don't
      advertise RSS they will not produce metadata anyway.  New
      firmwares advertising ABI 5.x, however, can depend on the
      driver defaulting to chained format.
      
      Fixes: f9380629 ("nfp: advertise support for NFD ABI 0.5")
      Suggested-by: default avatarMichael Rapson <michael.rapson@netronome.com>
      Signed-off-by: default avatarJakub Kicinski <jakub.kicinski@netronome.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      64a919a9
    • Jakub Kicinski's avatar
      nfp: remove legacy MAC address lookup · cb2cda48
      Jakub Kicinski authored
      The legacy MAC address lookup doesn't work well with breakout
      cables.  We are probably better off picking random addresses
      than the wrong ones in the theoretical scenario where management
      FW didn't tell us what the port config is.
      Signed-off-by: default avatarJakub Kicinski <jakub.kicinski@netronome.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      cb2cda48
    • Jakub Kicinski's avatar
      nfp: improve order of interfaces in breakout mode · 2eb333c4
      Jakub Kicinski authored
      For historical reasons we enumerate the vNICs in order.  This means
      that if user configures breakout on a multiport card, the first
      interface of the second port will have its MAC address changed.
      
      What's worse, when moved from static information (HWInfo) to using
      management FW (NSP), more features started depending on the port ids.
      Right now in case of breakout first subport of the second port and
      second subport of the first port will have their link info swapped.
      
      Revise the ordering scheme so that first subport maintains its address.
      Side effect of this change is that we will use base lane ids in
      devlink (i.e. 40G ports will be 4 ids apart), e.g.:
      
      pci/0000:04:00.0/0: type eth netdev p6p1
      pci/0000:04:00.0/4: type eth netdev p6p2
      
      Note that behaviour of phys_port_id is not changed since there is
      a separate id number for the subport there.
      
      Fixes: ec8b1fbe ("nfp: support port splitting via devlink")
      Signed-off-by: default avatarJakub Kicinski <jakub.kicinski@netronome.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      2eb333c4
    • Colin Ian King's avatar
      net: macb: remove extraneous return when MACB_EXT_DESC is defined · 42af627b
      Colin Ian King authored
      When macro MACB_EXT_DESC is defined we end up with two identical
      return statements and just one is sufficient. Remove the extra
      return.
      
      Detected by CoverityScan, CID#1449361 ("Structurally dead code")
      Signed-off-by: default avatarColin Ian King <colin.king@canonical.com>
      Acked-by: default avatarNicolas Ferre <nicolas.ferre@microchip.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      42af627b
    • Colin Ian King's avatar
      bpf: add missing break in for the TCP_BPF_SNDCWND_CLAMP case · 6d3f06a0
      Colin Ian King authored
      There appears to be a missing break in the TCP_BPF_SNDCWND_CLAMP case.
      Currently the non-error path where val is greater than zero falls through
      to the default case that sets the error return to -EINVAL. Add in
      the missing break.
      
      Detected by CoverityScan, CID#1449376 ("Missing break in switch")
      
      Fixes: 13bf9641 ("bpf: Adds support for setting sndcwnd clamp")
      Signed-off-by: default avatarColin Ian King <colin.king@canonical.com>
      Acked-by: default avatarDaniel Borkmann <daniel@iogearbox.net>
      Acked-by: default avatarLawrence Brakmo <brakmo@fb.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      6d3f06a0
    • Lawrence Brakmo's avatar
      bpf: fix return in load_bpf_file · f856e469
      Lawrence Brakmo authored
      The function load_bpf_file ignores the return value of
      load_and_attach(), so even if load_and_attach() returns an error,
      load_bpf_file() will return 0.
      
      Now, load_bpf_file() can call load_and_attach() multiple times and some
      can succeed and some could fail. I think the correct behavor is to
      return error on the first failed load_and_attach().
      
      v2: Added missing SOB
      Signed-off-by: default avatarLawrence Brakmo <brakmo@fb.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      f856e469
    • Roopa Prabhu's avatar
      mpls: fix rtm policy in mpls_getroute · ca4a1cd9
      Roopa Prabhu authored
      fix rtm policy name typo in mpls_getroute and also remove
      export of rtm_ipv4_policy
      
      Fixes: 397fc9e5 ("mpls: route get support")
      Reported-by: default avatarDavid S. Miller <davem@davemloft.net>
      Signed-off-by: default avatarRoopa Prabhu <roopa@cumulusnetworks.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      ca4a1cd9
    • Herbert Xu's avatar
      Merge git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6 · 035f901e
      Herbert Xu authored
      Merge the crypto tree to pull in fixes for the next merge window.
      035f901e
    • Kees Cook's avatar
      d1185a8c
    • Kees Cook's avatar
  3. 04 Jul, 2017 2 commits
    • Linus Torvalds's avatar
      Merge tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc · 19964541
      Linus Torvalds authored
      Pull ARM SoC 64-bit updates from Arnd Bergmann:
       "Changes to platform code for 64-bit ARM platforms.
      
        Andreas Färber adds two new platforms with initial code: Realtek
        RTD1295 and Action Semi S900. Both are fairly similar chips, used
        mainly in set-top-boxes, but with other possible applications, and
        additional members in the respective product families that could be
        added in the future. The code here is fairly minimal, as all the
        interesting parts are in device drivers and dts files.
      
        The Broadcom Vulcan platform gets dropped, as no products ever became
        available, and Cavium integrated the platform under a new name.
      
        Among some other defconfig changes, Timur Tabi enables a number of
        options that are typically required for server platforms"
      
      * tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
        arm64: defconfig: remove duplicate entry
        arm64: defconfig: enable Qualcomm Technologies EMAC and some PHY drivers
        arm64: defconfig: enable QCOM_L2_PMU and QCOM_L3_PMU
        arm64: defconfig: enable EDAC options
        arm64: defconfig: enable APEI and GHES features
        arm64: defconfig: enable support for PCIe hotplug
        arm64: defconfig: enable EFI_CAPSULE_LOADER
        arm64: defconfig: enable BLK_DEV_NVME
        arm64: defconfig: enable ACPI_CPPC_CPUFREQ
        arm64: marvell: enable ICU and GICP drivers
        arm64: marvell: enable the Armada 7K/8K pinctrl driver
        arm64: Prepare Actions Semi S900
        ARM64: defconfig: enable meson SPICC as module
        ARM64: defconfig: enable IR core, decoders and Meson IR device
        arm64: defconfig: enable Simple Sound Card support
        arm64: defconfig: Enable ARCH_BRCMSTB
        arm64: defconfig: drop ARCH_VULCAN
        arm64: disable Broadcom Vulcan platform
        MAINTAINERS: Add Realtek section
        ARM64: Prepare Realtek RTD1295
      19964541
    • Linus Torvalds's avatar
      Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc · a9ceea26
      Linus Torvalds authored
      Pull ARM 64-bit DT updates from Arnd Bergmann:
       "Device-tree updates for arm64 platforms. For the first time I can
        remember, this is actually larger than the corresponding branch for
        32-bit platforms overall, though that has more individual changes.
      
        A significant portion this time is due to added machine support:
      
         - Initial support for the Realtek RTD1295 SoC, along with the Zidoo
           X9S set-top-box
      
         - Initial support for Actions Semi S900 and the Bubblegum-96
           single-board-cёmputer.
      
         - Rockchips support for the rk3399-Firefly single-board-computer gets
           added, this one stands out for being relatively fast, affordable
           and well₋supported, compared to many boards that only fall into one
           or two of the above categories.
      
         - Mediatek gains support for the mt6797 mobile-phone SoC platform and
           corresponding evaluation board.
      
         - Amlogic board support gets added for the NanoPi K2 and S905x
           LibreTech CC single-board computers and the R-Box Pro set-top-box
      
         - Allwinner board support gets added for the OrangePi Win, Orangepi
           Zero Plus 2, NanoPi NEO2 and Orange Pi Prime single board computers
           and the SoPine system-on-module.
      
         - Renesas board support for Salvator-XS and H3ULCB automotive
           development systems.
      
         - Socionext Uniphier board support for LD11-global and LD20-global,
           whatever those may be.
      
         - Broadcom adds support for the new Stingray communication processor
           in its iProc family, along with two reference boards.
      
        Other updates include:
      
         - For the hisicon platform, support for Hi3660-Hikey960 gets extended
           significantly.
      
         - Lots of smaller updates for Renesas, Amlogic, Rockchip, UniPhier,
           Broadcom, Allwinner, Hisilicon, Qualcomm, Marvell, and NXP"
      
      * tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (243 commits)
        ARM64: dts: marvell: armada37xx: Fix timer interrupt specifiers
        Revert "arm64: dts: marvell: add dma-mask in crypto nodes for 7k/8k"
        arm64: dts: mediatek: don't include missing file
        ARM64: dts: meson-gxl: Add Libre Technology CC support
        dt-bindings: arm: amlogic: Add Libre Technology CC board
        dt-bindings: add Libre Technology vendor prefix
        arm64: dts: marvell: enable GICP and ICU on Armada 7K/8K
        arm64: dts: zte: Use - instead of @ for DT OPP entries
        arm64: dts: marvell: add gpio support for Armada 7K/8K
        arm64: dts: marvell: add pinctrl support for Armada 7K/8K
        arm64: dts: marvell: use new binding for the system controller on cp110
        arm64: dts: marvell: remove *-clock-output-names on cp110
        arm64: dts: marvell: use new bindings for xor clocks on ap806
        arm64: dts: marvell: mcbin: enable the mdio node
        arm64: dts: Add Actions Semi S900 and Bubblegum-96
        dt-bindings: Add vendor prefix for uCRobotics
        arm64: dts: marvell: add xmdio nodes for 7k/8k
        arm64: dts: marvell: add a comment on the cp110 slave node status
        arm64: dts: marvell: remove cpm crypto nodes from dts files
        arm64: dts: marvell: cp110: enable the crypto engine at the SoC level
        ...
      a9ceea26