- 25 Jul, 2016 40 commits
-
-
Dong Aisheng authored
The tuning bits like FBCLK_SEL, SMP_CLK_SEL and DLY_CELL which affects timing may have already been set by ROM if booting from SD3.0 mode like SDR104. Let's clear it first during driver probe before doing the new card enumeration to avoid working on the wrong timing. Note that tuning bits are dynamical settings which may need to be kept during MMC_PM_KEEP_POWER suspend, so we did not put them into hwinit function. Signed-off-by:
Dong Aisheng <aisheng.dong@nxp.com> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Dong Aisheng authored
sdhci_esdhc_imx_hwinit() includes all basic hw intialization. Calling it after resume to re-initialize hw in case its state is already lost in low power mode. Signed-off-by:
-
Dong Aisheng authored
Move tuning static configuration into basic hwinit function. Tuning configuration may also be lost in low power mode, so need restore in hwinit(). Acked-by:
-
Dong Aisheng authored
Move all hw related static initializations into a separate function which helps concentrate the hw related initialization code. And that function could also be called by other places later as a basic hw state restore. e.g. suspend/resume where the hw state is possible to lost due to low power mode. Signed-off-by:
-
Dong Aisheng authored
When enable DDR, the clock factor definition is changed. e.g. original 200Mhz will become 100Mhz once MIX_CTRL_DDREN bit is set So we need to update the clock setting then the strobe dll can lock the correct clock rate. Additionally we also need disable the clock before locking strobe dll. Acked-by:
-
Dong Aisheng authored
Indicating hw auto retuning support for mx6qdl in the fake caps_1 register and enable auto retuning in post_tuning process after tuning completes. Acked-by:
-
Dong Aisheng authored
Enable HW auto retuning when set SDHCI_CTRL_EXEC_TUNING and clear it when clear SDHCI_CTRL_TUNED_CLK. Acked-by:
-
Dong Aisheng authored
If HW supports SDHCI_TUNING_MODE_3 which is auto retuning, we won't retune during runtime suspend and resume, instead we use Re-tuning Request signaled via SDHCI_INT_RETUNE interrupt to do retuning and hw auto retuning during data transfer to guarantee the signal sample window correction. This can avoid a mass of repeatedly retuning during small file system data access and improve the performance. Signed-off-by:
-
Dong Aisheng authored
add tuning start point binding Signed-off-by:
-
Dong Aisheng authored
The delay cells of some SoCs may have less delay per one cell, for such SoCs, user could set the start delay cell point to bypass the first a few meaningless tuning commands. Acked-by:
-
Dong Aisheng authored
Disable DLL delay line settings explicitly during driver initialization in case ROM/uBoot had set an invalid delay. e.g. MX6DL ROM has set the default delay line(DLLCTRL) to 0x1000021, the uSDHC clock timing will become marginal when works on DDR mode due to default delay and will possibly see CRC errors in case the board is not perfectly designed on the eMMC chip layout. Acked-by:
-
Dong Aisheng authored
Currently, we config the watermark_level register only in probe. This will cause the mmc write operation timeout issue after system resume back in LPSR mode. Because in LPSR mode, after system resume back, the watermark_level register(0x44) changes to 0x08000880, which set the write watermark level as 0, and set the read watermark level as 128. This value is incorrect. This patch restores the setting of watermark level register after system resume back. Signed-off-by:
-
Dong Aisheng authored
It will be used for platform specific suspend/resume state save/restore work for some low power mode like Mega/Fast or LPSR mode. Acked-by:
-
Dong Aisheng authored
The driver has already implemented the private .set_timeout() callback for common SDHCI code to do correct timeout value setting, it does not need call sdhci_calc_timeout(), so this quirk actually is not working. Remove it now. Acked-by:
-
Dong Aisheng authored
Switch to use the more robust common mmc_regulator_set_vqmmc() function in MMC core which set the target voltage as close as possible to target voltage. We did not re-factor the whole sdhci_start_signal_voltage_switch() cause we want to keep the original signal switch order between host and card to avoid potential break. Signed-off-by:
-
Andy Shevchenko authored
This makes the error handling much more simpler than open-coding everything and in addition makes the probe function smaller an tidier. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by:
-
Bojan Prtvar authored
Export DSR register through sysfs same as we did for the CID, CSD and OCR registers. Signed-off-by:
Bojan Prtvar <prtvar.b@gmail.com> Signed-off-by:
-
Jaehoon Chung authored
In dw_mmc.c, it's enabled by default. It doesn't need to set MMC_CAP_ERASE in rockchip anymore. Signed-off-by:
Jaehoon Chung <jh80.chung@samsung.com> Acked-by:
Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by:
-
Jaehoon Chung authored
This flag needs to use the trim/discard/erase commands. dwmmc controller enables this flag by default. Signed-off-by:
-
Shawn Lin authored
The reason for why we expose these to dt is that some of the controller is unable to send special cmd type due to the hw limitation. Signed-off-by:
-
Shawn Lin authored
This patch adds description for no-sd, no-sdio, no-mmc. We expose these to DT as some of the controllers are unable to deal with special cmd type due to hw limitation. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Bojan Prtvar authored
Registers CID and CSD are already exported through sysfs so let's make this interface complete by adding missing OCR register. Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Stefan Wahren authored
The capabilities in iproc platform data are magic numbers. So replace them with the proper capability defines to make it readable. Signed-off-by:
Stefan Wahren <stefan.wahren@i2se.com> Acked-by:
Scott Branden <scott.branden@broadcom.com> Acked-by:
-
Stefan Wahren authored
This patch adds the missing define for the suspend/resume capability (according to SD Host Controller spec). Signed-off-by:
-
Shawn Lin authored
Host drivers which needs to valdiate for non-supported MMC commands and returnn error code for such requests. To improve and simplify the behaviour, let's invent MMC_CAP2_NO_MMC which these host drivers can set to tell the mmc core to skip sending MMC commands during card initialization. Signed-off-by:
-
Krzysztof Kozlowski authored
The driver registered for CPU frequency transitions to recalculate its clock when ARM clock frequency changes (ratio between frequencies of ARM's parent clock (fclk) and clock for peripherals remains fixed). This is needed only on S3C24xx platform when cpufreq driver is enabled so limit the ifdef to respective cpufreq Kconfig. Suggested-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by:
-
Adrian Hunter authored
sdhci_send_command() starts a timer to catch cases where the host controller fails. The timer is normally deleted when the request completes, but in the case of sdhci_execute_tuning() the request is handled differently and the timer is left running. This goes unnoticed because tuning is done before another command so the timer gets reset then. That should not be relied upon, so make sdhci_execute_tuning() delete the timer. Signed-off-by:
-
Adrian Hunter authored
The STOP command is sent in error conditions, even when the command is not finished. Avoid triggering the warning for that in sdhci_send_command() by setting host->cmd to NULL first. Signed-off-by:
-
Adrian Hunter authored
In order to support commands during data transfer, it will be possible to need to reset the command circuit while the data circuit is in use, and vice versa. It is now easy to determine whether the command or data circuit is in use, and so just skip the corresponding reset if it is. Signed-off-by:
-
Adrian Hunter authored
Factor out sdhci_auto_cmd12() so that there is a single place that controls whether auto-CMD12 is used. Signed-off-by:
-
Adrian Hunter authored
In order to support commands during data transfer, there will have to be up to two active requests (mrqs) at a time, instead of just one. That means recording which request is finished. Doing that obsoletes host->mrq which is therefore removed. Signed-off-by:
-
Adrian Hunter authored
In order to support commands during data transfer, there will have to be up to two active requests (mrqs) at a time, instead of just one. Provide two timers instead of just one. One of the timers is for requests that do not use the data lines, and the other one is for requests that do. Signed-off-by:
-
Adrian Hunter authored
Factor out sdhci_data_line_cmd() to improve readability and because it is used in multiple places. Signed-off-by:
-
Adrian Hunter authored
In order to support commands during data transfer, there will have to be up to two active requests (mrqs) at a time, instead of just one. That means ensuring that all requests get errored out in the cases of card or driver removal. Signed-off-by:
-
Adrian Hunter authored
Several pointers are used to identify when interrupts are expected. Namely, host->cmd, host->data_cmd and host->data. Ensure those are cleared when a request finishes. That tidies the case when a request is errored out before normal processing has completed, ensuring any interrupts that occur subsequently are not acted upon. Signed-off-by:
-
Adrian Hunter authored
SDHCI recovers from errors by resetting the cmd and data circuits. Until that is done, there very well might be more interrupts, so ignore them in that case. Signed-off-by:
-
Adrian Hunter authored
Factor out sdhci_needs_reset() so it can be reused. Signed-off-by:
-
Adrian Hunter authored
In order to support commands during data transfer, there will have to be up to two active requests (mrqs) at a time, instead of just one. That means the driver must identify which one to finish. Prepare for that by factoring out sdhci_finish_mrq(). Signed-off-by:
-
Adrian Hunter authored
In order to support commands during data transfer, it will be possible that host->data is not NULL when preparing a new request. Move a warning that assumes otherwise. Signed-off-by:
-
Adrian Hunter authored
In order to support commands during data transfer, there will have to be up to two active requests (mrqs) at a time, instead of just one. That means host->mrq will not be able to be used. In several places, host->mrq is used when instead the mrq can be determined from the cmd or data pointers. Reduce the use of host->mrq by doing that. Signed-off-by:
-
