This function has become trivial enough that it may as well be pushed into
its callers, which has the side-benefit of clarifying what's going on.

Remove it, and rename brcmf_sdiod_set_sbaddr_window() to
brcmf_sdiod_set_backplane_window() as it's easier to understand.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Trivial tidy of register definitions.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Primarily this patch removes:

brcmf_sdiod_f0_writeb()
brcmf_sdiod_reg_write()
brcmf_sdiod_reg_read()

Since we no longer use the quirky method of deciding which function to
address via the address being accessed, take the opportunity to rename
some IO functions more in line with common kernel code. We also convert
those that map directly to sdio_{read,write}*() to macros.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Whilst this if () statement is technically correct, it lacks clarity.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[arend: mention function in patch subject]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This function needs to be split up into separate read / write variants
for clarity.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Use the ARRAY_SIZE macro on rfseq_updategainu_events to determine
size of the array. Improvement suggested by coccinelle.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Using the ARRAY_SIZE macro improves the readability of the code. Also,
it is not always useful to use a variable to store this constant
calculated at compile time.

Found with Coccinelle with the following semantic patch:
@r depends on (org || report)@
type T;
T[] E;
position p;
@@
(
 (sizeof(E)@p /sizeof(*E))
|
 (sizeof(E)@p /sizeof(E[...]))
|
 (sizeof(E)@p /sizeof(T))
)
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

I accidentally pushed a patch with CPTCFG (which is used in the
backports project) to the rs-fw.c file.  Fix that to use CONFIG
instead.

Fixes: 9f66a397 ("iwlwifi: mvm: rs: add ops for the new rate scaling in the FW")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Merge tag 'iwlwifi-next-for-kalle-2017-12-05' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next

Second batch of iwlwifi updates for v4.16

* Initial work for rate-scaling offload;
* Support for new FW API version;
* Some fixes here and there;

No need to get into the submenu to disable all SSB-related
config entries.

This makes it easier to disable all SSB config options
without entering the submenu. It will also enable one
to see that en/dis-abled state from the outside menu.

This is only intended to change menuconfig UI, not change
the config dependencies.
Signed-off-by: Vincent Legoll <vincent.legoll@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

MT76x2e is a 2x2 PCIe 802.11ac chipset by MediaTek. This driver has full
support for AP, station, ad-hoc, mesh and monitor mode.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This will be used by drivers for MT76x2e, MT7603e and MT7628
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add documentation describing how device tree can be used to configure
wireless chips supported by the mt76 driver.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

use * for block comments in multiple lines according to kernel coding
style

Reported by: checkpatch.pl
Signed-off-by: Ashish Kalra <eashishkalra@gmail.com>
Reviewed-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

(1) Change virtual interface operation in cfg80211 process reset and
reinitilize private data structure.
(2) Scan result event processed in main process will dereference private
data structure concurrently, ocassionly crash the kernel.

The cornel case could be trigger by below steps:
(1) wpa_cli mlan0 scan
(2) ./hostapd mlan0.conf

Cfg80211 asynchronous scan procedure is not all the time operated
under rtnl lock, here we add the protect to serialize the cfg80211
scan and change_virtual interface operation.
Signed-off-by: Limin Zhu <liminzhu@marvell.com>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Firmware do not support change interface from micro-ap mode
to station mode, forbid this operation
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Trivial fix to spelling mistake in error message text.  Also remove the
error message on an kzalloc failure as this is redundant.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

when enabling wowlan and entering suspend the last write to the firmware
allowing it to go into elp mode was not completing before suspend, leaving
the firmware running in full active mode consuming high power.
Use an immediate call instead of a work queue for this last access
allowing the firmware to go into power save during wowlan uspend.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Using getnstimeofday()/timespec_to_ns() causes an overflow on 32-bit
architectures in 2038, and may suffer from time jumps due to
settimeofday() or leap seconds.

I don't see a reason why this needs to be UTC, so either monotonic
or boot time would be better here. Assuming that the fw time keeps
running during suspend, boottime is better than monotonic, and
ktime_get_boot_ns() will also save the additional conversion to
nanoseconds.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add non-DFS 5G upper channels (149-165) besides existed 4 lower channels
(36, 40, 44, 48).
Signed-off-by: Weixiao Zhang <waveletboy@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

cck_poweri cannot be greated than 15 as is derived from the bottom 4 bits
from riv->channels[channel - 1].hw_value & 0xf.  Hence the check for it
being greater than 15 is redundant and can be removed.

Detected by CoverityScan, CID#744303 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Remove the duplicate checking of TX ring's available number, and remove
the variable to store available number that can be calculated by
read/write pointers.
Signed-off-by: Steven Ting <steventing@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Give correct fifo size to calculate fifo space. Fortunately, the values of
RTL_PCI_MAX_RX_COUNT and TX_DESC_NUM_92E are the same in old code, so it
still works.
Signed-off-by: Steven Ting <steventing@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Check remaining count of RX packets cost a lot of CPU time, so only update
when the counter decreases to zero. In old flow, the counter was updated
once a RX packet is received.
Signed-off-by: Steven Ting <steventing@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

With the RTL8822BE and later devices, the number of interrupt vectors
has grown from 2 to 4. At this point, saving and passing those vectors
in a struct makes more sense than using individual scaler variables.

In two of the drivers, code to process the second of the interrupt
registers was included, but commented out. This patch removes those
useless sections.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Trivial cleanup of nasty variable name
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

If you need debugging this low level, you're doing something wrong.
Remove these noisy debug statements so the code is more readable.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Unlikely to be a problem, but brcmf_sdiod_regrl() is
not symmetric with brcmf_sdiod_regrb() in initializing
the data value on stack. Fix that.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
[arend: reword the commit message a bit]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This function is obfuscating how IO works on this chip. Remove it
and push its logic into brcmf_sdiod_reg_{read,write}().

Handling of -ENOMEDIUM is altered, but as that's pretty much broken anyway
we can ignore that.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Register access code is not the place for band-aid fixes like this.
If this is a genuine problem, it should be fixed further up in the driver
stack.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The value passed to brcmf_sdiod_addrprep() is *always* 4
remove this parameter and the unused code to handle it.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This function sets the address of the IO window used for
SDIO accesses onto the backplane of the chip.

It currently uses 3 separate masks despite the full mask being
defined in the code already. Remove the separate masks and clean up.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This large function is concealing a LOT of obscure logic about
how the hardware functions. Time to split it up.

This first patch splits the function into two pieces - read and write,
doing away with the rw flag in the process.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The 4 IO functions in this patch are incorrect as they use compiler types
to determine how many bytes to send to the hardware.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

All the other IO functions are the other way round in this
driver. Make this one match.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When statistics are read from debugfs, make sure that they
are actually updated from the firmware.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

If FW loads without a problem, leaving init_dbg on can
cause a confusion, since the user won't necessarily
remember it is still turned on, and there are flows in
which everything continues as usual, only without
stopping the device after INIT, even if there is no FW
assert. On 22000 HW, for instance, this causes a
warning, since the paging is getting initialized twice.

Solve the issue by making this module param effective
only if the FW indeed asserts during INIT.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

When sending LQ command, verify the rate scaling is not in firmware.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Replace sprintf by scnprintf throughout rs code.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>