- 21 Oct, 2019 4 commits
-
-
Olof Johansson authored
Merge tag 'v5.4-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes A number of fixes for individual boards like the rockpro64, and Hugsun X99 as well as a fix for the Gru-Kevin display override and fixing the dt- binding for Theobroma boards to the correct naming that is also actually used in the wild. * tag 'v5.4-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: arm64: dts: rockchip: Fix override mode for rk3399-kevin panel arm64: dts: rockchip: Fix usb-c on Hugsun X99 TV Box arm64: dts: rockchip: fix RockPro64 sdmmc settings arm64: dts: rockchip: fix RockPro64 sdhci settings arm64: dts: rockchip: fix RockPro64 vdd-log regulator settings dt-bindings: arm: rockchip: fix Theobroma-System board bindings arm64: dts: rockchip: fix Rockpro64 RK808 interrupt line Link: https://lore.kernel.org/r/1599050.HRXuSXmxRg@philSigned-off-by: Olof Johansson <olof@lixom.net>
-
Olof Johansson authored
Merge tag 'imx-fixes-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes i.MX fixes for 5.4: - Re-enable SNVS power key for imx6q-logicpd board which was accidentally disabled by a SoC level change. - Fix I2C switches on vf610-zii-scu4-aib board by specifying property i2c-mux-idle-disconnect. - A fix on imx-scu API that reads UID from firmware to avoid kernel NULL pointer dump. - A series from Anson to correct i.MX7 GPT and i.MX8 USDHC IPG clock. - A fix on DRM_MSM Kconfig regression on i.MX5 by adding the option explicitly into imx_v6_v7_defconfig. - Fix ARM regulator states issue for zii-ultra board, which is impacting stability of the board. - A correction on CPU core idle state name for LayerScape LX2160A SoC. * tag 'imx-fixes-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: ARM: imx_v6_v7_defconfig: Enable CONFIG_DRM_MSM arm64: dts: imx8mn: Use correct clock for usdhc's ipg clk arm64: dts: imx8mm: Use correct clock for usdhc's ipg clk arm64: dts: imx8mq: Use correct clock for usdhc's ipg clk ARM: dts: imx7s: Correct GPT's ipg clock source ARM: dts: vf610-zii-scu4-aib: Specify 'i2c-mux-idle-disconnect' ARM: dts: imx6q-logicpd: Re-Enable SNVS power key arm64: dts: lx2160a: Correct CPU core idle state name arm64: dts: zii-ultra: fix ARM regulator states soc: imx: imx-scu: Getting UID from SCU should have response Link: https://lore.kernel.org/r/20191017141851.GA22506@dragonSigned-off-by: Olof Johansson <olof@lixom.net>
-
Olof Johansson authored
Merge tag 'omap-for-v5.4/fixes-rc3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes Fixes for omaps for v5.4-rc cycle More fixes for omap variants: - Update more panel options in omap2plus_defconfig that got changed as we moved to use generic LCD panels - Remove unused twl_keypad for logicpd-torpedo-som to avoid boot time warnings. This is only a cosmetic fix, but at least dmesg output is now getting more readable after all the fixes to remove pointless warnings - Fix gpu_cm node name as we still have a non-standard node name dependency for clocks. This should eventually get fixed by use of domain specific compatible property - Fix use of i2c-mux-idle-disconnect for m3874-iceboard - Use level interrupt for omap4 & 5 wlcore to avoid lost edge interrupts * tag 'omap-for-v5.4/fixes-rc3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: dts: Use level interrupt for omap4 & 5 wlcore ARM: dts: am3874-iceboard: Fix 'i2c-mux-idle-disconnect' usage ARM: dts: omap5: fix gpu_cm clock provider name ARM: dts: logicpd-torpedo-som: Remove twl_keypad ARM: omap2plus_defconfig: Fix selected panels after generic panel changes Link: https://lore.kernel.org/r/pull-1571242890-118432@atomide.comSigned-off-by: Olof Johansson <olof@lixom.net>
-
Olof Johansson authored
Merge tag 'arm-soc/for-5.4/devicetree-arm64-fixes' of https://github.com/Broadcom/stblinux into arm/fixes This pull request contains Broadcom ARM64-based SoCs Device Tree fixes for 5.4, please pull the following: - Rayangonda fixes the GPIO pins assignment for the Stringray SoCs * tag 'arm-soc/for-5.4/devicetree-arm64-fixes' of https://github.com/Broadcom/stblinux: arm64: dts: Fix gpio to pinmux mapping Link: https://lore.kernel.org/r/20191015172356.9650-2-f.fainelli@gmail.comSigned-off-by: Olof Johansson <olof@lixom.net>
-
- 14 Oct, 2019 8 commits
-
-
Fabio Estevam authored
Since commit 2eba6907 ("drm/msm: Remove Kconfig default") the CONFIG_DRM_MSM option is no longer selected by default on i.MX5. Explicitly select CONFIG_DRM_MSM so that we can get GPU support by default on i.MX51 and i.MX53. Fixes: 2eba6907 ("drm/msm: Remove Kconfig default") Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Anson Huang authored
On i.MX8MN, usdhc's ipg clock is from IMX8MN_CLK_IPG_ROOT, assign it explicitly instead of using IMX8MN_CLK_DUMMY. Fixes: 6c3debcb ("arm64: dts: freescale: Add i.MX8MN dtsi support") Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Anson Huang authored
On i.MX8MM, usdhc's ipg clock is from IMX8MM_CLK_IPG_ROOT, assign it explicitly instead of using IMX8MM_CLK_DUMMY. Fixes: a05ea40e ("arm64: dts: imx: Add i.mx8mm dtsi support") Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Anson Huang authored
On i.MX8MQ, usdhc's ipg clock is from IMX8MQ_CLK_IPG_ROOT, assign it explicitly instead of using IMX8MQ_CLK_DUMMY. Fixes: 748f908c ("arm64: add basic DTS for i.MX8MQ") Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Anson Huang authored
i.MX7S/D's GPT ipg clock should be from GPT clock root and controlled by CCM's GPT CCGR, using correct clock source for GPT ipg clock instead of IMX7D_CLK_DUMMY. Fixes: 3ef79ca6 ("ARM: dts: imx7d: use imx7s.dtsi as base device tree") Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Andrey Smirnov authored
Specify 'i2c-mux-idle-disconnect' for both I2C switches present on the board, since both are connected to the same parent bus and all of their children have the same I2C address. Fixes: ca4b4d37 ("ARM: dts: vf610: Add ZII SCU4 AIB board") Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Jeff White <jeff.white@zii.aero> Cc: Rick Ramstetter <rick@anteaterllc.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: linux-arm-kernel@lists.infradead.org Cc: devicetree@vger.kernel.org Cc: linux-kernel@vger.kernel.org Tested-by: Chris Healy <cphealy@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Adam Ford authored
A previous patch disabled the SNVS power key by default which breaks the ability for the imx6q-logicpd board to wake from sleep. This patch re-enables this feature for this board. Fixes: 770856f0 ("ARM: dts: imx6qdl: Enable SNVS power key according to board design") Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Ran Wang authored
lx2160a support PW15 but not PW20, correct name to avoid confusing. Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Fixes: 00c5ce8a ("arm64: dts: lx2160a: add cpu idle support") Acked-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
- 11 Oct, 2019 2 commits
-
-
Tony Lindgren authored
-
git://git.infradead.org/linux-mvebuOlof Johansson authored
mvebu fixes for 5.4 (part 1) Fix regression on USB for Turris Mox (Armada 3720 based board) * tag 'mvebu-fixes-5.4-1' of git://git.infradead.org/linux-mvebu: arm64: dts: armada-3720-turris-mox: convert usb-phy to phy-supply Link: https://lore.kernel.org/r/87blunsm43.fsf@FE-laptopSigned-off-by: Olof Johansson <olof@lixom.net>
-
- 10 Oct, 2019 3 commits
-
-
Douglas Anderson authored
When I re-posted Sean's original commit to add the override mode for the kevin panel, for some reason I didn't notice that the pixel clock wasn't quite right. Looking at /sys/kernel/debug/clk/clk_summary on downstream kernels it can be seen that the VOP clock is supposed to be 266,666,667 Hz achieved by dividing the 800 MHz PLL by 3. Looking at history, it seems that even Sean's first patch [1] had this funny clock rate. I'm not sure where it came from since the commit message specifically mentioned 26666 kHz and the Chrome OS tree [2] can be seen to request 266667 kHz. In any case, let's fix it up. This together with my patch [3] to do the proper rounding when setting the clock rate makes the VOP clock more proper as seen in /sys/kernel/debug/clk/clk_summary. [1] https://lore.kernel.org/r/20180206165626.37692-4-seanpaul@chromium.org [2] https://chromium.googlesource.com/chromiumos/third_party/kernel/+/chromeos-4.4/drivers/gpu/drm/panel/panel-simple.c#1172 [3] https://lkml.kernel.org/r/20191003114726.v2.1.Ib233b3e706cf6317858384264d5b0ed35657456e@changeid Fixes: 84ebd2da ("arm64: dts: rockchip: Specify override mode for kevin panel") Cc: Sean Paul <seanpaul@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20191008124949.1.I674acd441997dd0690c86c9003743aacda1cf5dd@changeidSigned-off-by: Heiko Stuebner <heiko@sntech.de>
-
Vivek Unune authored
Fix usb-c on X99 TV Box. Tested with armbian w/ kernel 5.3 Signed-off-by: Vivek Unune <npcomplete13@gmail.com> Link: https://lore.kernel.org/r/20190929032230.24628-1-npcomplete13@gmail.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>
-
Soeren Moch authored
According to the RockPro64 schematic [1] the rk3399 sdmmc controller is connected to a microSD (TF card) slot. Remove the cap-mmc-highspeed property of the sdmmc controller, since no mmc card can be connected here. [1] http://files.pine64.org/doc/rockpro64/rockpro64_v21-SCH.pdf Fixes: e4f3fb49 ("arm64: dts: rockchip: add initial dts support for Rockpro64") Signed-off-by: Soeren Moch <smoch@web.de> Link: https://lore.kernel.org/r/20191004203213.4995-1-smoch@web.deSigned-off-by: Heiko Stuebner <heiko@sntech.de>
-
- 09 Oct, 2019 2 commits
-
-
Tony Lindgren authored
Commit 572cf7d7 ("ARM: dts: Improve omap l4per idling with wlcore edge sensitive interrupt") changed wlcore interrupts to use edge interrupt based on what's specified in the wl1835mod.pdf data sheet. However, there are still cases where we can have lost interrupts as described in omap_gpio_unidle(). And using a level interrupt instead of edge interrupt helps as we avoid the check for untriggered GPIO interrupts in omap_gpio_unidle(). And with commit e6818d29 ("gpio: gpio-omap: configure edge detection for level IRQs for idle wakeup") GPIOs idle just fine with level interrupts. Let's change omap4 and 5 wlcore users back to using level interrupt instead of edge interrupt. Let's not change the others as I've only seen this on omap4 and 5, probably because the other SoCs don't have l4per idle independent of the CPUs. Fixes: 572cf7d7 ("ARM: dts: Improve omap l4per idling with wlcore edge sensitive interrupt") Depends-on: e6818d29 ("gpio: gpio-omap: configure edge detection for level IRQs for idle wakeup") Cc: Anders Roxell <anders.roxell@linaro.org> Cc: Eyal Reizer <eyalr@ti.com> Cc: Guy Mishol <guym@ti.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Marek Behún authored
Update Turris Mox device tree to use the phy-supply property of the generic PHY framework instead of the legacy usb-phy property. This is needed since it caused a regression on Turris Mox since "usb: host: xhci-plat: Prevent an abnormally restrictive PHY init skipping". Signed-off-by: Marek Behún <marek.behun@nic.cz> Fixes: eb6c2eb6 ("usb: host: xhci-plat: Prevent an abnormally restrictive PHY init skipping") Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Cc: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
-
- 08 Oct, 2019 2 commits
-
-
Andrey Smirnov authored
According to Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt, i2c-mux-idle-disconnect is a property of a parent node since it pertains to the mux/switch as a whole, so move it there and drop all of the concurrences in child nodes. Fixes: d0317731 ("ARM: dts: Adds device tree file for McGill's IceBoard, based on TI AM3874") Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Benoît Cousson <bcousson@baylibre.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Graeme Smecher <gsmecher@threespeedlogic.com> Cc: linux-omap@vger.kernel.org Cc: devicetree@vger.kernel.org Cc: linux-kernel@vger.kernel.org Tested-by: Graeme Smecher <gsmecher@threespeedlogic.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Tero Kristo authored
The clkctrl code searches for the parent clockdomain based on the name of the CM provider node. The introduction of SGX node for omap5 made the node name for the gpu_cm to be clock-controller. There is no clockdomain named like this, so the lookup fails. Fix by changing the node name properly. Fixes: 394534cb ("ARM: dts: Configure sgx for omap5") Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
- 06 Oct, 2019 2 commits
-
-
Lucas Stach authored
The GPIO controlled regulator for the ARM power supply is supplying the higher voltage when the GPIO is driven high. This is opposite to the similar regulator setup on the EVK board and is impacting stability of the board as the ARM domain has been supplied with a too low voltage when to faster OPPs are in use. Fixes: 4a13b3be (arm64: dts: imx: add Zii Ultra board support) Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Anson Huang authored
The SCU firmware API for getting UID should have response, otherwise, the message stored in function stack could be released and then the response data received from SCU will be stored into that released stack and cause kernel NULL pointer dump. Fixes: 73feb4d0 ("soc: imx-scu: Add SoC UID(unique identifier) support") Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
- 04 Oct, 2019 5 commits
-
-
Soeren Moch authored
The RockPro64 schematics [1], [2] show that the rk3399 EMMC_STRB pin is connected to the RESET pin instead of the DATA_STROBE pin of the eMMC module. So the data strobe cannot be used for its intended purpose on this board, and so the HS400 eMMC mode is not functional. Limit the controller to HS200. [1] http://files.pine64.org/doc/rockpro64/rockpro64_v21-SCH.pdf [2] http://files.pine64.org/doc/rock64/PINE64_eMMC_Module_20170719.pdf Fixes: e4f3fb49 ("arm64: dts: rockchip: add initial dts support for Rockpro64") Signed-off-by: Soeren Moch <smoch@web.de> Link: https://lore.kernel.org/r/20191003215036.15023-2-smoch@web.deSigned-off-by: Heiko Stuebner <heiko@sntech.de>
-
Soeren Moch authored
The RockPro64 schematic [1] page 18 states a min voltage of 0.8V and a max voltage of 1.4V for the VDD_LOG pwm regulator. However, there is an additional note that the pwm parameter needs to be modified. From the schematics a voltage range of 0.8V to 1.7V can be calculated. Additional voltage measurements on the board show that this fix indeed leads to the correct voltage, while without this fix the voltage was set too high. [1] http://files.pine64.org/doc/rockpro64/rockpro64_v21-SCH.pdf Fixes: e4f3fb49 ("arm64: dts: rockchip: add initial dts support for Rockpro64") Signed-off-by: Soeren Moch <smoch@web.de> Link: https://lore.kernel.org/r/20191003215036.15023-1-smoch@web.deSigned-off-by: Heiko Stuebner <heiko@sntech.de>
-
Patrice Chotard authored
SPI_STM32_QSPI must be set in buildin as rootfs can be located on QSPI memory device. Link: https://lore.kernel.org/r/20191004124025.17394-1-patrice.chotard@st.comSigned-off-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Olof Johansson <olof@lixom.net>
-
Adam Ford authored
The TWL4030 used on the Logit PD Torpedo SOM does not have the keypad pins routed. This patch disables the twl_keypad driver to remove some splat during boot: twl4030_keypad 48070000.i2c:twl@48:keypad: missing or malformed property linux,keymap: -22 twl4030_keypad 48070000.i2c:twl@48:keypad: Failed to build keymap twl4030_keypad: probe of 48070000.i2c:twl@48:keypad failed with error -22 Signed-off-by: Adam Ford <aford173@gmail.com> [tony@atomide.com: removed error time stamps] Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Tony Lindgren authored
-
- 03 Oct, 2019 4 commits
-
-
Heiko Stuebner authored
The naming convention for the existing Theobroma boards is soc-q7module-baseboard, so rk3399-puma-haikou and the in-kernel devicetrees also follow that scheme. For some reason in the binding a wrong or outdated naming slipped in which does not match the used devicetrees and makes the dt-schema complain now. Fix this by using the names used in the wild by actual boards. Fixes: a323a513 ("dt-bindings: arm: Convert Rockchip board/soc bindings to json-schema") [although the issue was also present in the old txt file] Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20190917083453.25744-1-heiko@sntech.de
-
Hugh Cole-Baker authored
Fix the pinctrl and interrupt specifier for RK808 to use GPIO3_B2. On the Rockpro64 schematic [1] page 16, it shows GPIO3_B2 used for the interrupt line PMIC_INT_L from the RK808, and there's a note which translates as: "PMU termination GPIO1_C5 changed to this". Tested by setting an RTC wakealarm and checking /proc/interrupts counters. Without this patch, neither the rockchip_gpio_irq counter for the RK808, nor the RTC alarm counter increment when the alarm time is reached. With this patch, both interrupt counters increment by 1 as expected. [1] http://files.pine64.org/doc/rockpro64/rockpro64_v21-SCH.pdf Fixes: e4f3fb49 ("arm64: dts: rockchip: add initial dts support for Rockpro64") Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com> Link: https://lore.kernel.org/r/20190921131457.36258-1-sigmaris@gmail.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>
-
Tony Lindgren authored
The old omapdrm panels got removed for v5.4 in favor of generic panels, and the Kconfig options changed. Let's update omap2plus_defconfig accordingly so the same panels are still enabled. Cc: Jyri Sarha <jsarha@ti.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Olof Johansson authored
Merge tag 'omap-for-v5.4/fixes-rc1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes Fixes for omaps for v5.4-rc cycle Here are fixes for omaps to deal with few regressions, and to fix more boot time errors and warnings: - The recent ti-sysc interconnect target module driver changes had incorrect clock bits for both clocks and dts that cause warnings - For omap3-gta04, gpio changes caused the LCD to break a while back, and after discussing things the right fix is to set spi-cs-high - Recent omapdrm changes to use generic panels caused tfp410 to be disabled as we now must enable the generic support for it in defconfig - Recent omapdrm and backlight changes also finally made droid4 LCD to work, so let's enable it in the defconfig it can be used out of the box. This is not strictly a fix, but we still also have the older CONFIG_MFD_TI_LMU options available so this cuts down the confusion for trying to guess which display and which backlight is needed - Recent ti-sysc interconnect target module changes need the gpio module disabled on some boards, but this now needs to happen at the module level, not at the gpio driver level - Recent changes to probe system timers with ti-sysc caused warnings about mismatch in syconfig registers, so let's configure the option for RESET_STATUS as available in the TRMs - Recent changes to probe LCDC with ti-sysc caused warnings about mismatch in sysconfig registers, so let's configure the missing idlemodes for both platform data and dts as documented in TRMs - Since we moved mach-omap2 to probe with device tree, we've been getting voltage controller warnings. Turns out this code is no longer needed, so let's just remove omap2_set_init_voltage() to get rid of the pointless warnings - Configure am4372 dispc memory bandwidth to avoid underflow errors * tag 'omap-for-v5.4/fixes-rc1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: dts: am4372: Set memory bandwidth limit for DISPC ARM: OMAP2+: Fix warnings with broken omap2_set_init_voltage() ARM: OMAP2+: Add missing LCDC midlemode for am335x ARM: OMAP2+: Fix missing reset done flag for am3 and am43 ARM: dts: Fix gpio0 flags for am335x-icev2 ARM: omap2plus_defconfig: Enable more droid4 devices as loadable modules ARM: omap2plus_defconfig: Enable DRM_TI_TFP410 DTS: ARM: gta04: introduce legacy spi-cs-high to make display work again ARM: dts: Fix wrong clocks for dra7 mcasp clk: ti: dra7: Fix mcasp8 clock bits Link: https://lore.kernel.org/r/pull-1570040410-308159@atomide.comSigned-off-by: Olof Johansson <olof@lixom.net>
-
- 01 Oct, 2019 1 commit
-
-
Linus Walleij authored
This fixes up the default ux500 CPU thermal zone: - Set polling delay to 0 and explain why - Set passive polling delay to 250 - Remove restrictions from the CPU cooling device, we should use all cpufreq steps to cool down if needed. Link: https://lore.kernel.org/r/20191001074628.8122-1-linus.walleij@linaro.org Fixes: b786a05f ("ARM: dts: ux500: Update thermal zone") Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
-
- 30 Sep, 2019 7 commits
-
-
Rayagonda Kokatanur authored
There are total of 151 non-secure gpio (0-150) and four pins of pinmux (91, 92, 93 and 94) are not mapped to any gpio pin, hence update same in DT. Fixes: 8aa428cc ("arm64: dts: Add pinctrl DT nodes for Stingray SOC") Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com> Reviewed-by: Ray Jui <ray.jui@broadcom.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
-
Keerthy authored
Commit 6334150e ("remoteproc: don't allow modular build") changes CONFIG_REMOTEPROC to a boolean from a tristate config option which inhibits all defconfigs marking CONFIG_REMOTEPROC as a module in compiling the remoteproc and dependent config options. So fix the configs to have CONFIG_REMOTEPROC built in. Link: https://lore.kernel.org/r/20190920075946.13282-5-j-keerthy@ti.com Fixes: 6334150e ("remoteproc: don't allow modular build") Signed-off-by: Keerthy <j-keerthy@ti.com> Acked-by: Will Deacon <will@kernel.org> [olof: Fixed up all 4 occurrances in this one commit] Signed-off-by: Olof Johansson <olof@lixom.net>
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linuxLinus Torvalds authored
Pull btrfs fixes from David Sterba: "A bunch of fixes that accumulated in recent weeks, mostly material for stable. Summary: - fix for regression from 5.3 that prevents to use balance convert with single profile - qgroup fixes: rescan race, accounting leak with multiple writers, potential leak after io failure recovery - fix for use after free in relocation (reported by KASAN) - other error handling fixups" * tag 'for-5.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux: btrfs: qgroup: Fix reserved data space leak if we have multiple reserve calls btrfs: qgroup: Fix the wrong target io_tree when freeing reserved data space btrfs: Fix a regression which we can't convert to SINGLE profile btrfs: relocation: fix use-after-free on dead relocation roots Btrfs: fix race setting up and completing qgroup rescan workers Btrfs: fix missing error return if writeback for extent buffer never started btrfs: adjust dirty_metadata_bytes after writeback failure of extent buffer Btrfs: fix selftests failure due to uninitialized i_mode in test inodes
-
git://github.com/c-sky/csky-linuxLinus Torvalds authored
Pull csky updates from Guo Ren: "This round of csky subsystem just some fixups: - Fix mb() synchronization problem - Fix dma_alloc_coherent with PAGE_SO attribute - Fix cache_op failed when cross memory ZONEs - Optimize arch_sync_dma_for_cpu/device with dma_inv_range - Fix ioremap function losing - Fix arch_get_unmapped_area() implementation - Fix defer cache flush for 610 - Support kernel non-aligned access - Fix 610 vipt cache flush mechanism - Fix add zero_fp fixup perf backtrace panic - Move static keyword to the front of declaration - Fix csky_pmu.max_period assignment - Use generic free_initrd_mem() - entry: Remove unneeded need_resched() loop" * tag 'csky-for-linus-5.4-rc1' of git://github.com/c-sky/csky-linux: csky: Move static keyword to the front of declaration csky: entry: Remove unneeded need_resched() loop csky: Fixup csky_pmu.max_period assignment csky: Fixup add zero_fp fixup perf backtrace panic csky: Use generic free_initrd_mem() csky: Fixup 610 vipt cache flush mechanism csky: Support kernel non-aligned access csky: Fixup defer cache flush for 610 csky: Fixup arch_get_unmapped_area() implementation csky: Fixup ioremap function losing csky: Optimize arch_sync_dma_for_cpu/device with dma_inv_range csky/dma: Fixup cache_op failed when cross memory ZONEs csky: Fixup dma_alloc_coherent with PAGE_SO attribute csky: Fixup mb() synchronization problem
-
git://git.kernel.org/pub/scm/linux/kernel/git/soc/socLinus Torvalds authored
Pull ARM SoC fixes from Olof Johansson: "A few fixes that have trickled in through the merge window: - Video fixes for OMAP due to panel-dpi driver removal - Clock fixes for OMAP that broke no-idle quirks + nfsroot on DRA7 - Fixing arch version on ASpeed ast2500 - Two fixes for reset handling on ARM SCMI" * tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: ARM: aspeed: ast2500 is ARMv6K reset: reset-scmi: add missing handle initialisation firmware: arm_scmi: reset: fix reset_state assignment in scmi_domain_reset bus: ti-sysc: Remove unpaired sysc_clkdm_deny_idle() ARM: dts: logicpd-som-lv: Fix i2c2 and i2c3 Pin mux ARM: dts: am3517-evm: Fix missing video ARM: dts: logicpd-torpedo-baseboard: Fix missing video ARM: omap2plus_defconfig: Fix missing video bus: ti-sysc: Fix handling of invalid clocks bus: ti-sysc: Fix clock handling for no-idle quirks
-
Peter Ujfalusi authored
Set memory bandwidth limit to filter out resolutions above 720p@60Hz to avoid underflow errors due to the bandwidth needs of higher resolutions. am43xx can not provide enough bandwidth to DISPC to correctly handle 'high' resolutions. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-