- 03 Mar, 2016 40 commits
-
-
James Hogan authored
commit f4dce1ff upstream. Since commit 4c21b8fd ("MIPS: seccomp: Handle indirect system calls (o32)"), syscall_get_arguments() attempts to handle o32 indirect syscall arguments by incrementing both the start argument number and the number of arguments to fetch. However only the start argument number needs to be incremented. The number of arguments does not change, they're just shifted up by one, and in fact the output array is provided by the caller and is likely only n entries long, so reading more arguments overflows the output buffer. In the case of seccomp, this results in it fetching 7 arguments starting at the 2nd one, which overflows the unsigned long args[6] in populate_seccomp_data(). This clobbers the $s0 register from syscall_trace_enter() which __seccomp_phase1_filter() saved onto the stack, into which syscall_trace_enter() had placed its syscall number argument. This caused Chromium to crash. Credit goes to Milko for tracking it down as far as $s0 being clobbered. Fixes: 4c21b8fd ("MIPS: seccomp: Handle indirect system calls (o32)") Reported-by:
Milko Leporis <milko.leporis@imgtec.com> Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/12213/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Huacai Chen authored
commit 4f33f6c5 upstream. Commit be0c37c9 (MIPS: Rearrange PTE bits into fixed positions.) defines fixed PTE bits for MIPS R2. Then, commit d7b63141 (MIPS: pgtable-bits: Fix XPA damage to R6 definitions.) adds the MIPS R6 definitions in the same way as MIPS R2. But some R6 #ifdefs in the later commit are missing, so in this patch I fix that. Signed-off-by:
Huacai Chen <chenhc@lemote.com> Cc: Aurelien Jarno <aurelien@aurel32.net> Cc: Steven J. Hill <Steven.Hill@imgtec.com> Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/12164/Signed-off-by:
-
Huacai Chen authored
commit 5610b125 upstream. This patch is borrowed from x86 hpet driver and explaind below: Due to the overly intelligent design of HPETs, we need to workaround the problem that the compare value which we write is already behind the actual counter value at the point where the value hits the real compare register. This happens for two reasons: 1) We read out the counter, add the delta and write the result to the compare register. When a NMI hits between the read out and the write then the counter can be ahead of the event already. 2) The write to the compare register is delayed by up to two HPET cycles in AMD chipsets. We can work around this by reading back the compare register to make sure that the written value has hit the hardware. But that is bad performance wise for the normal case where the event is far enough in the future. As we already know that the write can be delayed by up to two cycles we can avoid the read back of the compare register completely if we make the decision whether the delta has elapsed already or not based on the following calculation: cmp = event - actual_count; If cmp is less than 64 HPET clock cycles, then we decide that the event has happened already and return -ETIME. That covers the above #1 and #2 problems which would cause a wait for HPET wraparound (~306 seconds). Signed-off-by:
-
Huacai Chen authored
commit 57548432 upstream. When Core-0 handle SMP_ASK_C0COUNT IPI, we should make other cores to see the result as soon as possible (especially when Store-Fill-Buffer is enabled). Otherwise, C0_Count syncronization makes no sense. BTW, array is more suitable than per-cpu variable for syncronization, and there is a corner case should be avoid: C0_Count of Core-0 can be really 0. Signed-off-by:
-
Dan Williams authored
commit 800dc4f4 upstream. This reverts commit 22b14523. It was originally sent in an earlier revision of the pfn_t patchset. Besides being broken, the warning is also fixed by PFN_FLAGS_MASK casting the PAGE_MASK to an unsigned long. Reported-by:
Manuel Lauss <manuel.lauss@gmail.com> Signed-off-by:
Dan Williams <dan.j.williams@intel.com> Cc: linux-kernel@vger.kernel.org Cc: Linux-MIPS <linux-mips@linux-mips.org> Patchwork: https://patchwork.linux-mips.org/patch/12182/Signed-off-by:
-
zengtao authored
commit 0f26922f upstream. The datatype __kernel_time_t is u32 on 32bit platform, so its subject to overflows in the timeval/timespec to cputime conversion. Currently the following functions are affected: 1. setitimer() 2. timer_create/timer_settime() 3. sys_clock_nanosleep This can happen on MIPS32 and ARM32 with "Full dynticks CPU time accounting" enabled, which is required for CONFIG_NO_HZ_FULL. Enforce u64 conversion to prevent the overflow. Fixes: 31c1fc81 ("ARM: Kconfig: allow full nohz CPU accounting") Signed-off-by:
zengtao <prime.zeng@huawei.com> Reviewed-by:
Arnd Bergmann <arnd@arndb.de> Cc: <fweisbec@gmail.com> Link: http://lkml.kernel.org/r/1454384314-154784-1-git-send-email-prime.zeng@huawei.comSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
David Gibson authored
commit 35a4933a upstream. 1e75fa8b "time: Condense timekeeper.xtime into xtime_sec" replaced a call to clocksource_cyc2ns() from timekeeping_get_ns() with an open-coded version of the same logic to avoid keeping a semi-redundant struct timespec in struct timekeeper. However, the commit also introduced a subtle semantic change - where clocksource_cyc2ns() uses purely unsigned math, the new version introduces a signed temporary, meaning that if (delta * tk->mult) has a 63-bit overflow the following shift will still give a negative result. The choice of 'maxsec' in __clocksource_updatefreq_scale() means this will generally happen if there's a ~10 minute pause in examining the clocksource. This can be triggered on a powerpc KVM guest by stopping it from qemu for a bit over 10 minutes. After resuming time has jumped backwards several minutes causing numerous problems (jiffies does not advance, msleep()s can be extended by minutes..). It doesn't happen on x86 KVM guests, because the guest TSC is effectively frozen while the guest is stopped, which is not the case for the powerpc timebase. Obviously an unsigned (64 bit) overflow will only take twice as long as a signed, 63-bit overflow. I don't know the time code well enough to know if that will still cause incorrect calculations, or if a 64-bit overflow is avoided elsewhere. Still, an incorrect forwards clock adjustment will cause less trouble than time going backwards. So, this patch removes the potential for intermediate signed overflow. Suggested-by:
Laurent Vivier <lvivier@redhat.com> Tested-by:
David Gibson <david@gibson.dropbear.id.au> Signed-off-by:
John Stultz <john.stultz@linaro.org> Signed-off-by:
-
Lukasz Duda authored
commit 87f5fedb upstream. This patch fixes incorrect handling of the 6lowpan packets that contain uncompressed IPv6 header. RFC4944 specifies a special dispatch for 6lowpan to carry uncompressed IPv6 header. This dispatch (1 byte long) has to be removed during reception and skb data pointer has to be moved. To correctly point in the beginning of the IPv6 header the dispatch byte has to be pulled off before packet can be processed by netif_rx_in(). Test scenario: IPv6 packets are not correctly interpreted by the network layer when IPv6 header is not compressed (e.g. ICMPv6 Echo Reply is not propagated correctly to the ICMPv6 layer because the extra byte will make the header look corrupted). Similar approach is done for IEEE 802.15.4. Signed-off-by:
Lukasz Duda <lukasz.duda@nordicsemi.no> Signed-off-by:
Glenn Ruben Bakke <glenn.ruben.bakke@nordicsemi.no> Acked-by:
Jukka Rissanen <jukka.rissanen@linux.intel.com> Signed-off-by:
Johan Hedberg <johan.hedberg@intel.com> Signed-off-by:
-
Glenn Ruben Bakke authored
commit 4c58f328 upstream. The fixes provided in this patch assigns a valid net_device structure to skb before dispatching it for further processing. Scenario #1: ============ Bluetooth 6lowpan receives an uncompressed IPv6 header, and dispatches it to netif. The following error occurs: Null pointer dereference error #1 crash log: [ 845.854013] BUG: unable to handle kernel NULL pointer dereference at 0000000000000048 [ 845.855785] IP: [<ffffffff816e3d36>] enqueue_to_backlog+0x56/0x240 ... [ 845.909459] Call Trace: [ 845.911678] [<ffffffff816e3f64>] netif_rx_internal+0x44/0xf0 The first modification fixes the NULL pointer dereference error by assigning dev to the local_skb in order to set a valid net_device before processing the skb by netif_rx_ni(). Scenario #2: ============ Bluetooth 6lowpan receives an UDP compressed message which needs further decompression by nhc_udp. The following error occurs: Null pointer dereference error #2 crash log: [ 63.295149] BUG: unable to handle kernel NULL pointer dereference at 0000000000000840 [ 63.295931] IP: [<ffffffffc0559540>] udp_uncompress+0x320/0x626 [nhc_udp] The second modification fixes the NULL pointer dereference error by assigning dev to the local_skb in the case of a udp compressed packet. The 6lowpan udp_uncompress function expects that the net_device is set in the skb when checking lltype. Signed-off-by:
-
Johan Hedberg authored
commit cff10ce7 upstream. The commit cad20c27 was supposed to fix handling of devices first using public addresses and then switching to RPAs after pairing. Unfortunately it missed a couple of key places in the code. 1. When evaluating which devices should be removed from the existing white list we also need to consider whether we have an IRK for them or not, i.e. a call to hci_find_irk_by_addr() is needed. 2. In smp_notify_keys() we should not be requiring the knowledge of the RPA, but should simply keep the IRK around if the other conditions require it. Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Dmitry Tunin authored
commit 1623d0bf upstream. BugLink: https://bugs.launchpad.net/bugs/1522949 T: Bus=03 Lev=02 Prnt=02 Port=05 Cnt=02 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0930 ProdID=0225 Rev=01.12 S: Manufacturer=Broadcom Corp S: Product=BCM43142A0 S: SerialNumber=4CBB58034671 C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Signed-off-by:
Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by:
-
Johan Hedberg authored
commit 2f99536a upstream. All LE connections are now triggered through a preceding passive scan and waiting for a connectable advertising report. This means we've got the best possible guarantee that the device is within range and should be able to request the controller to perform continuous scanning. This way we minimize the risk that we miss out on any advertising packets. Signed-off-by:
-
K. Y. Srinivasan authored
commit 8599846d upstream. Currently we have two policies for deciding when to signal the host: One based on the ring buffer state and the other based on what the VMBUS client driver wants to do. Consider the case when the client wants to explicitly control when to signal the host. In this case, if the client were to defer signaling, we will not be able to signal the host subsequently when the client does want to signal since the ring buffer state will prevent the signaling. Implement logic to have only one signaling policy in force for a given channel. Signed-off-by:
K. Y. Srinivasan <kys@microsoft.com> Reviewed-by:
Haiyang Zhang <haiyangz@microsoft.com> Tested-by:
-
Dexuan Cui authored
commit a689d251 upstream. Fix the write()'s argument in the daemon code. Cc: Vitaly Kuznetsov <vkuznets@redhat.com> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Signed-off-by:
Dexuan Cui <decui@microsoft.com> Signed-off-by:
-
Adrian Hunter authored
commit 8d28b7a7 upstream. Drivers may need to provide their own get_cd() mmc host op, but currently the internals of the current op (sdhci_get_cd()) are provided by sdhci_do_get_cd() which is also called from sdhci_request(). To allow override of the get_cd functionality, change sdhci_request() to call ->get_cd() instead of sdhci_do_get_cd(). Note, in the future the call to ->get_cd() will likely be removed from sdhci_request() since most drivers don't need actually it. However this change is being done now to facilitate a subsequent bug fix. Signed-off-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Adrian Hunter authored
commit bf60e592 upstream. In the past, fixes for specific hardware devices were implemented in sdhci using quirks. That approach is no longer accepted because the growing number of quirks was starting to make the code difficult to understand and maintain. One alternative to quirks, is to allow drivers to override the default mmc host operations. This patch makes it easy to do that, and it is needed for a subsequent bug fix, for which separate patches are provided. Signed-off-by:
-
Adrian Hunter authored
commit 163cbe31 upstream. Intel BXT/APL use a card detect GPIO however the host controller will not enable bus power unless it's card detect also reflects the presence of a card. Unfortunately those 2 things race which can result in commands not starting, after which the controller does nothing and there is a 10 second wait for the driver's 10-second timer to timeout. That is fixed by having the driver look also at the present state register to determine if the card is present. Consequently, provide a 'get_cd' mmc host operation for BXT/APL that does that. Signed-off-by:
-
Robert Jarzmik authored
commit 41c89159 upstream. The commit fixing the conversion of pxamci to slot-gpio API fixed the inverted the logic of the read-only gpio. Unfortunately, the commit was tested on a non-inverted gpio, and not on the inverted one. And the fix did work partially, by luck. This is the remaining missing part of the fix, trivial but still necessary. Fixes: Fixes: 26d49fe7 ("mmc: pxamci: fix read-only gpio detection polarity") Reported-by:
Andrea Adami <andrea.adami@gmail.com> Tested-by:
Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by:
-
Adrian Hunter authored
commit 6a645dd8 upstream. Intel BXT/APL use a card detect GPIO however the host controller will not enable bus power unless it's card detect also reflects the presence of a card. Unfortunately those 2 things race which can result in commands not starting, after which the controller does nothing and there is a 10 second wait for the driver's 10-second timer to timeout. That is fixed by having the driver look also at the present state register to determine if the card is present. Consequently, provide a 'get_cd' mmc host operation for BXT/APL that does that. Signed-off-by:
-
Linus Walleij authored
commit 0bcb7efd upstream. commit 4956e109 ("ARM: 6244/1: mmci: add variant data and default MCICLOCK support") added variant data for ARM, U300 and Ux500 variants. The Nomadik NHK8815/8820 variant was erroneously labeled as a U300 variant, and when the proper Nomadik variant was later introduced in commit 34fd4213 ("ARM: 7378/1: mmci: add support for the Nomadik MMCI variant") this was not fixes. Let's say this fixes the latter commit as there was no proper Nomadik support until then. Fixes: 34fd4213 ("ARM: 7378/1: mmci: add support for the Nomadik...") Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Carlo Caione authored
commit e10c3219 upstream. While in sdhci_execute_tuning() the choice whether or not to enable the tuning is done on the actual timing, in the mmc_sdio_init_uhs_card() the check is done on the capability of the card. This difference is causing some issues with some SDIO cards in DDR50 mode where the CDM19 is wrongly issued. With this patch we modify the check in both mmc_(sd|sdio)_init_uhs_card() functions to take the proper decision only according to the actual timing specification. Signed-off-by:
Carlo Caione <carlo@endlessm.com> Signed-off-by:
-
Adrian Hunter authored
commit 5c671c41 upstream. sdhci has a legacy facility to prevent runtime suspend if the bus power is on. This is needed in cases where the power to the card is dependent on the bus power. It is controlled by a pair of functions: sdhci_runtime_pm_bus_on() and sdhci_runtime_pm_bus_off(). These functions use a boolean variable 'bus_on' to ensure changes are always paired. There is an additional check for 'runtime_suspended' which is the problem. In fact, its use is ill-conceived as the only requirement for the logic is that 'on' and 'off' are paired, which is actually broken by the check, for example if the bus power is turned on during runtime resume. So remove the check. Signed-off-by:
-
Wenkai Du authored
commit adb24d42 upstream. Commit cc4f414c ("mmc: mmc: Add driver strength selection") added driver strength selection for eMMC HS200 and HS400 modes. That patch also set the driver stength when transitioning through High Speed mode to HS200/HS400, but driver strength is not defined for High Speed mode. While the JEDEC specification is not clear on this point it has been observed to cause problems for some eMMC, and removing the driver strength setting in this case makes it consistent with the normal use of High Speed mode. Signed-off-by:
Wenkai Du <wenkai.du@intel.com> Signed-off-by:
-
Adrian Hunter authored
commit d9bfbb95 upstream. The 'ocr' parameter passed to mmc_set_signal_voltage() defines the power-on voltage used when power cycling after a failure to set the voltage. However, in the case of mmc_sdio_init_card(), the value passed has the R4_18V_PRESENT flag set which is not valid for power-on and results in an invalid vdd. Fix by passing the card's ocr value which does not have the flag. Signed-off-by:
-
Adrian Hunter authored
commit 347ea32d upstream. SDHCI has built-in DMA called ADMA2. ADMA2 uses a descriptor table to define DMA scatter-gather. Each desciptor can specify a data length up to 65536 bytes, however the length field is only 16-bits so zero means 65536. Consequently, putting zero when the size is zero must not be allowed. This patch fixes one case where zero data length could be set inadvertently. The problem happens because unaligned data gets split and the code did not consider that the remaining aligned portion might be zero length. That case really only happens for SDIO because SD and eMMC cards transfer blocks that are invariably sector- aligned. For SDIO, access to function registers is done by data transfer (CMD53) when the register is bigger than 1 byte. Generally registers are 4 bytes but 2-byte registers are possible. So DMA of 4 bytes or less can happen. When 32-bit DMA is used, the data alignment must be 4, so 4-byte transfers won't casue a problem, but a 2-byte transfer could. However with the introduction of 64-bit DMA, the data alignment for 64-bit DMA was made 8 bytes, so all 4-byte transfers not on 8-byte boundaries get "split" into a 4-byte chunk and a 0-byte chunk, thereby hitting the bug. In fact, a closer look at the SDHCI specs indicates that only the descriptor table requires 8-byte alignment for 64-bit DMA. That will be dealt with in a separate patch, but the potential for a 2-byte access remains, so this fix is needed anyway. Signed-off-by:
-
Adrian Hunter authored
commit 1ca89685 upstream. In some cases, the stronger 33 Ohm driver strength must not be used so it is not a suitable default. Change it to the standard default 50 Ohm value. The patch applies to v4.2+ except the file name changed. It is drivers/mmc/host/sdhci-pci.c prior to v.4.4. Signed-off-by:
-
Rabin Vincent authored
commit 05caee93 upstream. Commit bb08a7d4 ("mmc: usdhi6rol0: fix NULL pointer deref in debug print") fixed one NULL pointer dereference but unfortunately introduced another. "data" may be NULL if this is a command timeout for a command without any data, so we should only use it if we're actually waiting for data. Fixes: bb08a7d4 ("mmc: usdhi6rol0: fix NULL pointer deref in debug print") Signed-off-by:
Rabin Vincent <rabin.vincent@axis.com> Signed-off-by:
-
Alexandre Belloni authored
commit f02b4b72 upstream. clockevents_exchange_device is calling clockevents_shutdown() on the new clockenvents device but it may have never been enabled in the first place. This results in the tcb clock being disabled without being enabled first: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 1 at drivers/clk/clk.c:680 clk_disable+0x28/0x34() Modules linked in: CPU: 0 PID: 1 Comm: swapper Not tainted 4.4.0+ #6 Hardware name: Atmel AT91SAM9 [<c000f2b8>] (unwind_backtrace) from [<c000d01c>] (show_stack+0x10/0x14) [<c000d01c>] (show_stack) from [<c00172f0>] (warn_slowpath_common+0x78/0xa0) [<c00172f0>] (warn_slowpath_common) from [<c00173a8>] (warn_slowpath_null+0x18/0x20) [<c00173a8>] (warn_slowpath_null) from [<c0361528>] (clk_disable+0x28/0x34) [<c0361528>] (clk_disable) from [<c034d560>] (tc_shutdown+0x38/0x4c) [<c034d560>] (tc_shutdown) from [<c0059ad4>] (clockevents_switch_state+0x38/0x6c) [<c0059ad4>] (clockevents_switch_state) from [<c0059b18>] (clockevents_shutdown+0x10/0x24) [<c0059b18>] (clockevents_shutdown) from [<c005a458>] (tick_check_new_device+0x84/0xac) [<c005a458>] (tick_check_new_device) from [<c0059660>] (clockevents_register_device+0x7c/0x108) [<c0059660>] (clockevents_register_device) from [<c06b5a68>] (tcb_clksrc_init+0x390/0x3e8) [<c06b5a68>] (tcb_clksrc_init) from [<c00097cc>] (do_one_initcall+0x114/0x1d4) [<c00097cc>] (do_one_initcall) from [<c069bd54>] (kernel_init_freeable+0xfc/0x1b8) [<c069bd54>] (kernel_init_freeable) from [<c04c3818>] (kernel_init+0x8/0xe0) [<c04c3818>] (kernel_init) from [<c000a410>] (ret_from_fork+0x14/0x24) ---[ end trace 0000000000000001 ]--- Check what state we were in before trying to disable the clock. Fixes: cf4541c1 ("clockevents/drivers/tcb_clksrc: Migrate to new 'set-state' interface") Signed-off-by:
Alexandre Belloni <alexandre.belloni@free-electrons.com> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Boris Brezillon <boris.brezillon@free-electrons.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Link: http://lkml.kernel.org/r/1452854061-30370-1-git-send-email-alexandre.belloni@free-electrons.comSigned-off-by:
-
Richard Cochran authored
commit 1b9f2372 upstream. The posix_clock_poll function is supposed to return a bit mask of POLLxxx values. However, in case the hardware has disappeared (due to hot plugging for example) this code returns -ENODEV in a futile attempt to throw an error at the file descriptor level. The kernel's file_operations interface does not accept such error codes from the poll method. Instead, this function aught to return POLLERR. The value -ENODEV does, in fact, contain the POLLERR bit (and almost all the other POLLxxx bits as well), but only by chance. This patch fixes code to return a proper bit mask. Credit goes to Markus Elfring for pointing out the suspicious signed/unsigned mismatch. Reported-by:
Markus Elfring <elfring@users.sourceforge.net> igned-off-by:
Richard Cochran <richardcochran@gmail.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Julia Lawall <julia.lawall@lip6.fr> Link: http://lkml.kernel.org/r/1450819198-17420-1-git-send-email-richardcochran@gmail.comSigned-off-by:
-
Ashok Kumar authored
commit 004fa08d upstream. When the GIC is using EOImode==1, the EOI is done immediately, leaving the deactivation to be performed when the EOI was previously done. Unfortunately, the ITS is not aware of the EOImode at all, and blindly EOIs the interrupt again. On most systems, this is ignored (despite being a programming error), but some others do raise a SError exception as there is no priority drop to perform for this interrupt. The fix is to stop trying to be clever, and always call into the underlying GIC to perform the right access, irrespective of the more we're in. [Marc: Reworked commit message] Fixes: 0b996fd3 ("irqchip/GICv3: Convert to EOImode == 1") Acked-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
Ashok Kumar <ashoks@broadcom.com> Signed-off-by:
-
Milo Kim authored
commit 49f34134 upstream. Atmel AIC has common structure for SMR (Source Mode Register). bit[6:5] Interrupt source type bit[2:0] Priority level Other bits are unused. To update new priority value, bit[2:0] should be cleared first and then new priority level can be written. However, aic_common_set_priority() helper clears source type bits instead of priority bits. This patch fixes wrong mask bit operation. Fixes: b1479ebb "irqchip: atmel-aic: Add atmel AIC/AIC5 drivers" Signed-off-by:
Milo Kim <milo.kim@ti.com> Acked-by:
Boris Brezillon <boris.brezillon@free-electrons.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Ludovic Desroches <ludovic.desroches@atmel.com> Cc: Nicholas Ferre <nicolas.ferre@atmel.com> Link: http://lkml.kernel.org/r/1452669592-3401-2-git-send-email-milo.kim@ti.comSigned-off-by:
-
Oleksij Rempel authored
commit c5b63520 upstream. The rework of the driver missed to move the call to set_handle_irq() into asm9260_of_init(). As a consequence no interrupt entry point is installed and no interrupts are delivered Solution is simple: Install the interrupt entry handler. Fixes: 7e4ac676 ("irqchip/mxs: Add Alphascale ASM9260 support") Signed-off-by:
Oleksij Rempel <linux@rempel-privat.de> Cc: kernel@pengutronix.de Cc: jason@lakedaemon.net Cc: marc.zyngier@arm.com Link: http://lkml.kernel.org/r/1454061473-24957-1-git-send-email-linux@rempel-privat.deSigned-off-by:
-
Sekhar Nori authored
commit d3b421cd upstream. Under some conditions, irq sorting procedure used by INTC can go wrong resulting in a spurious irq getting reported. If this condition is not handled, it results in endless stream of: unexpected IRQ trap at vector 00 messages from ack_bad_irq() Handle the spurious interrupt condition in omap-intc driver to prevent this. Measurements using kernel function profiler on AM335x EVM running at 720MHz show that after this patch omap_intc_handle_irq() takes about 37.4us against 34us before this patch. Signed-off-by:
Sekhar Nori <nsekhar@ti.com> Acked-by:
Tony Lindgren <tony@atomide.com> Cc: John Ogness <john.ogness@linutronix.de> Cc: Felipe Balbi <balbi@ti.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Marc Zyngier <marc.zyngier@arm.com> Link: http://lkml.kernel.org/r/9c78a6db02ac55f7af7371b417b6e414d2c3095b.1450188128.git.nsekhar@ti.comSigned-off-by:
-
Mathieu Poirier authored
commit fadf3a44 upstream. Connection child names associated to ports can sometimes be NULL, which is the case when booting a system on QEMU or when the Coresight power domain isn't switched on. This patch is adding a check to make sure a NULL string isn't fed to strcmp(), something that avoid crashing the system. Reported-by:
Tyler Baker <tyler.baker@linaro.org> Signed-off-by:
Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by:
-
Mike Snitzer authored
commit 4328daa2 upstream. Using request-based DM mpath configured with the following stacking (.request_fn DM mpath ontop of scsi-mq paths): echo Y > /sys/module/scsi_mod/parameters/use_blk_mq echo N > /sys/module/dm_mod/parameters/use_blk_mq 'struct dm_rq_target_io' would leak if a request is requeued before a blk-mq clone is allocated (or fails to allocate). free_rq_tio() wasn't being called. kmemleak reported: unreferenced object 0xffff8800b90b98c0 (size 112): comm "kworker/7:1H", pid 5692, jiffies 4295056109 (age 78.589s) hex dump (first 32 bytes): 00 d0 5c 2c 03 88 ff ff 40 00 bf 01 00 c9 ff ff ..\,....@....... e0 d9 b1 34 00 88 ff ff 00 00 00 00 00 00 00 00 ...4............ backtrace: [<ffffffff81672b6e>] kmemleak_alloc+0x4e/0xb0 [<ffffffff811dbb63>] kmem_cache_alloc+0xc3/0x1e0 [<ffffffff8117eae5>] mempool_alloc_slab+0x15/0x20 [<ffffffff8117ec1e>] mempool_alloc+0x6e/0x170 [<ffffffffa00029ac>] dm_old_prep_fn+0x3c/0x180 [dm_mod] [<ffffffff812fbd78>] blk_peek_request+0x168/0x290 [<ffffffffa0003e62>] dm_request_fn+0xb2/0x1b0 [dm_mod] [<ffffffff812f66e3>] __blk_run_queue+0x33/0x40 [<ffffffff812f9585>] blk_delay_work+0x25/0x40 [<ffffffff81096fff>] process_one_work+0x14f/0x3d0 [<ffffffff81097715>] worker_thread+0x125/0x4b0 [<ffffffff8109ce88>] kthread+0xd8/0xf0 [<ffffffff8167cb8f>] ret_from_fork+0x3f/0x70 [<ffffffffffffffff>] 0xffffffffffffffff crash> struct -o dm_rq_target_io struct dm_rq_target_io { ... } SIZE: 112 Fixes: e5863d9a ("dm: allocate requests in target when stacking on blk-mq devices") Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Mikulas Patocka authored
commit 385277bf upstream. When there is an error copying a chunk dm-snapshot can incorrectly hold associated bios indefinitely, resulting in hung IO. The function copy_callback sets pe->error if there was error copying the chunk, and then calls complete_exception. complete_exception calls pending_complete on error, otherwise it calls commit_exception with commit_callback (and commit_callback calls complete_exception). The persistent exception store (dm-snap-persistent.c) assumes that calls to prepare_exception and commit_exception are paired. persistent_prepare_exception increases ps->pending_count and persistent_commit_exception decreases it. If there is a copy error, persistent_prepare_exception is called but persistent_commit_exception is not. This results in the variable ps->pending_count never returning to zero and that causes some pending exceptions (and their associated bios) to be held forever. Fix this by unconditionally calling commit_exception regardless of whether the copy was successful. A new "valid" parameter is added to commit_exception -- when the copy fails this parameter is set to zero so that the chunk that failed to copy (and all following chunks) is not recorded in the snapshot store. Also, remove commit_callback now that it is merely a wrapper around pending_complete. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
-
Mike Snitzer authored
commit 51216778 upstream. Remove the unused struct block_op pointer that was inadvertantly introduced, via cut-and-paste of previous brb_op() code, as part of commit 50dd842a. (Cc'ing stable@ because commit 50dd842a did) Fixes: 50dd842a ("dm space map metadata: fix ref counting bug when bootstrapping a new space map") Reported-by:
David Binderman <dcb314@hotmail.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
commit e8beb023 upstream. The tda1004x was updating the properties cache before locking. If the device is not locked, the data at the registers are just random values with no real meaning. This caused the driver to fail with libdvbv5, as such library calls GET_PROPERTY from time to time, in order to return the DVB stats. Tested with a saa7134 card 78: ASUSTeK P7131 Dual, vendor PCI ID: 1043:4862 Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
-
Hans Verkuil authored
commit 4623e596 upstream. In the 3.17 kernel the poll() behavior changed for output streams: as long as not all buffers were queued up poll() would return that userspace can write. This is fine for the write() call, but when using stream I/O this changed the behavior since the expectation was that it would wait for buffers to become available for dequeuing. This patch only enables the check whether you can queue buffers for file I/O only, and skips it for stream I/O. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Acked-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Antonio Ospite authored
commit dcc7fdbe upstream. v4l2-compliance sends a zeroed struct v4l2_streamparm in v4l2-test-formats.cpp::testParmType(), and this results in a division by 0 in some gspca subdrivers: divide error: 0000 [#1] SMP Modules linked in: gspca_ov534 gspca_main ... CPU: 0 PID: 17201 Comm: v4l2-compliance Not tainted 4.3.0-rc2-ao2 #1 Hardware name: System manufacturer System Product Name/M2N-E SLI, BIOS ASUS M2N-E SLI ACPI BIOS Revision 1301 09/16/2010 task: ffff8800818306c0 ti: ffff880095c4c000 task.ti: ffff880095c4c000 RIP: 0010:[<ffffffffa079bd62>] [<ffffffffa079bd62>] sd_set_streamparm+0x12/0x60 [gspca_ov534] RSP: 0018:ffff880095c4fce8 EFLAGS: 00010296 RAX: 0000000000000000 RBX: ffff8800c9522000 RCX: ffffffffa077a140 RDX: 0000000000000000 RSI: ffff880095e0c100 RDI: ffff8800c9522000 RBP: ffff880095e0c100 R08: ffffffffa077a100 R09: 00000000000000cc R10: ffff880067ec7740 R11: 0000000000000016 R12: ffffffffa07bb400 R13: 0000000000000000 R14: ffff880081b6a800 R15: 0000000000000000 FS: 00007fda0de78740(0000) GS:ffff88012fc00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00000000014630f8 CR3: 00000000cf349000 CR4: 00000000000006f0 Stack: ffffffffa07a6431 ffff8800c9522000 ffffffffa077656e 00000000c0cc5616 ffff8800c9522000 ffffffffa07a5e20 ffff880095e0c100 0000000000000000 ffff880067ec7740 ffffffffa077a140 ffff880067ec7740 0000000000000016 Call Trace: [<ffffffffa07a6431>] ? v4l_s_parm+0x21/0x50 [videodev] [<ffffffffa077656e>] ? vidioc_s_parm+0x4e/0x60 [gspca_main] [<ffffffffa07a5e20>] ? __video_do_ioctl+0x280/0x2f0 [videodev] [<ffffffffa07a5ba0>] ? video_ioctl2+0x20/0x20 [videodev] [<ffffffffa07a59b9>] ? video_usercopy+0x319/0x4e0 [videodev] [<ffffffff81182dc1>] ? page_add_new_anon_rmap+0x71/0xa0 [<ffffffff811afb92>] ? mem_cgroup_commit_charge+0x52/0x90 [<ffffffff81179b18>] ? handle_mm_fault+0xc18/0x1680 [<ffffffffa07a15cc>] ? v4l2_ioctl+0xac/0xd0 [videodev] [<ffffffff811c846f>] ? do_vfs_ioctl+0x28f/0x480 [<ffffffff811c86d4>] ? SyS_ioctl+0x74/0x80 [<ffffffff8154a8b6>] ? entry_SYSCALL_64_fastpath+0x16/0x75 Code: c7 93 d9 79 a0 5b 5d e9 f1 f3 9a e0 0f 1f 00 66 2e 0f 1f 84 00 00 00 00 00 66 66 66 66 90 53 31 d2 48 89 fb 48 83 ec 08 8b 46 10 <f7> 76 0c 80 bf ac 0c 00 00 00 88 87 4e 0e 00 00 74 09 80 bf 4f RIP [<ffffffffa079bd62>] sd_set_streamparm+0x12/0x60 [gspca_ov534] RSP <ffff880095c4fce8> ---[ end trace 279710c2c6c72080 ]--- Following what the doc says about a zeroed timeperframe (see http://www.linuxtv.org/downloads/v4l-dvb-apis/vidioc-g-parm.html): ... To reset manually applications can just set this field to zero. fix the issue by resetting the frame rate to a default value in case of an unusable timeperframe. The fix is done in the subdrivers instead of gspca.c because only the subdrivers have notion of a default frame rate to reset the camera to. Signed-off-by:
Antonio Ospite <ao2@ao2.it> Reviewed-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
