- 28 Oct, 2014 40 commits
-
-
Prabhakar Lad authored
this patch groups the v4l2_ioctl_ops. Signed-off-by:
Lad, Prabhakar <prabhakar.csengg@gmail.com> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-
Prabhakar Lad authored
Signed-off-by:
-
Prabhakar Lad authored
this patch uses vb2_is_busy() helper to check if streaming is actually started, instead of driver managing it. Signed-off-by:
-
Prabhakar Lad authored
Signed-off-by:
-
Prabhakar Lad authored
Signed-off-by:
-
Prabhakar Lad authored
this patch adds support for using vb2_ioctl_* helpers. Signed-off-by:
-
Prabhakar Lad authored
this patch converts the driver to use fh handling provided by the v4l core instead of driver doing it. Signed-off-by:
-
Prabhakar Lad authored
this patch teaches vpbe driver to use vb2_fop_mmap/poll helpers. Signed-off-by:
-
Prabhakar Lad authored
this patch improve vpbe_buffer_prepare() callback, as buf_prepare() callback is never called with invalid state and check for vb2_plane_vaddr(vb, 0) is dropped as payload check should be done unconditionally. Signed-off-by:
-
Prabhakar Lad authored
this patch drops buf_cleanup() callback as this callback is never called with buffer state active. Signed-off-by:
-
Prabhakar Lad authored
this patch makes use of vb2_ops_wait_prepare/finish helper functions. Signed-off-by:
-
Prabhakar Lad authored
this patch drops the buf_init() callback as init of buf list is not required. Signed-off-by:
-
Prabhakar Lad authored
this patch moves the initialization of vb2 queue and the DMA context to probe() and clean up in remove() callback respectively. Signed-off-by:
-
ayaka authored
The NV12M is supported by all the version of MFC, so it is better to use it as default OUTPUT format. MFC v5 doesn't support NV21, I have tested it, for the SEC doc it is not supported either. Signed-off-by:
ayaka <ayaka@soulik.info> Signed-off-by:
Kamil Debski <k.debski@samsung.com> Signed-off-by:
-
Philipp Zabel authored
Patch b906352c ([media] coda: dequeue buffers if start_streaming fails) incorrectly marked buffers as DEQUEUED in case of start_streaming failure, when in fact they should be set to QUEUED. The videobuf2 core warns about this. Reported-by:
Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com> Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
-
Pawel Osciak authored
Interrupt result flags have to be cleared before a hardware job is run. Otherwise, if they are cleared asynchronously, we may end up clearing them after the interrupt for which we wanted to wait has already arrived, thus overwriting the job results that we intended to wait for. To prevent this, clear the flags only under hw_lock and before running a hardware job. Signed-off-by:
Pawel Osciak <posciak@chromium.org> Signed-off-by:
Kiran AVND <avnd.kiran@samsung.com> Signed-off-by:
Arun Kumar K <arun.kk@samsung.com> Signed-off-by:
-
Pawel Osciak authored
G_CTRL on V4L2_CID_MIN_BUFFERS_FOR_CAPTURE will fail if userspace happens to query it after getting a resolution change event and before the codec has a chance to parse the header and switch to an initialized state. Signed-off-by:
-
Pawel Osciak authored
This field is no longer used as MFC driver doesn't use vb2 alloc contexts anymore. Signed-off-by:
-
Kiran AVND authored
While resolution change is detected by MFC, we flush out older dpbs, send the resolution change event to application, and then accept further queuing of new src buffers. Sometimes, we error out during dpb flush because of lack of src buffers. Since we have not started decoding new resolution yet, it is simpler to push zero-size buffer until we flush out all dpbs. This is already been done while handling EOS command, and this patch extends the same logic to resolution change as well. Signed-off-by:
-
Arun Mankuzhi authored
If the software watchdog kicks in, we need to de-init MFC before reloading firmware and re-intializing it again. Signed-off-by:
Arun Mankuzhi <arun.m@samsung.com> Signed-off-by:
-
Arun Mankuzhi authored
MFC wakeup command has to be sent after the host receives firmware load complete status from risc. Signed-off-by:
-
Pawel Osciak authored
If the software watchdog kicks in, the watchdog worker is not synchronized with hardware interrupts and does not block other instances. It's possible for it to clear the hw_lock, making other instances trigger a BUG() on hw_lock checks. Since it's not fatal to clear the hw_lock to zero twice, just WARN in those cases for now. We should not explode, as firmware will return errors as needed for other instances after it's reloaded, or they will time out. A clean fix should involve killing other instances when watchdog kicks in, but requires a major redesign of locking in the driver. Signed-off-by:
-
Mauro Carvalho Chehab authored
drivers/media/platform/s5p-mfc/s5p_mfc_ctrl.c:132:5: warning: no previous prototype for 's5p_mfc_bus_reset' [-Wmissing-prototypes] int s5p_mfc_bus_reset(struct s5p_mfc_dev *dev) ^ Signed-off-by: -
Kiran AVND authored
during reset sequence, it is advisable to follow the below sequence, in order to avoid unexpected behavior from MFC . set SFR 0x7110 MFC_BUS_RESET_CTRL 0x1 // wait for REQ_STATUS to be 1 . get SFR 0x7110 MFC_BUS_RESET_CTRL 0x3 // reset now Signed-off-by:
-
Kiran AVND authored
Reset sequence for MFC V7 and V8 do not need RISC_ON to be set to 0, while for MFC V6 it is still needed. Also, remove a couple of register settings during Reset which are not needed from V6 onwards. Signed-off-by:
-
Ilja Friedel authored
Timestamp i of a previously decoded buffer was overwritten for some H.264 streams with timestamp i+1 of the next buffer. This happened when encountering frame_type S5P_FIMV_DECODE_FRAME_SKIPPED, indicating no new frame. In most cases this wrong indexing might not have been noticed except for a one frame delay in frame presentation. For H.264 streams though that require reordering of frames for presentation, it caused a slightly erratic presentation time lookup and consequently dropped frames in the Pepper Flash plugin. Signed-off-by:
Ilja H. Friedel <ihf@google.com> Signed-off-by:
-
Prathyush K authored
The enter_suspend flag is set after we enter mfc suspend function but if suspend fails after that due to any reason (like hardware timeout etc), this flag must be cleared before returning an error. Otherwise, this flag never gets cleared and the MFC suspend will always return an error on subsequent tries. If clock off fails, disable hw_lock also. Signed-off-by:
Prathyush K <prathyush.k@samsung.com> Signed-off-by:
-
Pawel Osciak authored
Handle REQBUFS(0) for CAPTURE queue as well. Also use the proper queue to call it on for OUTPUT. Signed-off-by:
-
Kiran AVND authored
Add V4L2_CID_MIN_BUFFERS_FOR_OUTPUT query for encoder. Once mfc encoder state is HEAD_PARSED, which is sequence header produced, dpb_count is avaialable. Let user space query this value. Signed-off-by:
-
Philipp Zabel authored
This patch adds a quick check for valid JPEG frames before feeding them into the bitstream buffer: Frames that do not begin with the JPEG start of image marker and end with the end of image marker are dropped. Signed-off-by:
-
Philipp Zabel authored
This should fix CODA crashes due to timeouts when stopping the decoding process with SIGINT. Signed-off-by:
-
Philipp Zabel authored
For small frame sizes, allocating 1 MiB per compressed buffer is a waste of space. On the other hand, incompressible 1080p data can produce JPEGs larger than 1 MiB at higher quality settings. Allow userspace to set the compressed buffer size and clamp the value to a sensible range. Also set the initial sizeimage to a value inside the range allowed by try_fmt. While at it, reduce the default image size to a maximum of 1920*1088 (otherwise JPEG will default to 8k*8k and 96 MiB buffers). Signed-off-by:
-
Philipp Zabel authored
With bitstream padding, it is possible to decode a single JPEG in the bitstream immediately. This allows us to only ever queue a single JPEG into the bitstream buffer, except to increase payload over 512 bytes or to back out of hold state. This is a measure to decrease JPEG decoder latency. Signed-off-by:
-
Philipp Zabel authored
Before starting a PIC_RUN, pad the bitstream with 0xff until 256 bytes past the next multiple of 256 bytes, if the buffer to be decoded is the last buffer in the bitstream. Signed-off-by:
-
Philipp Zabel authored
Storing the buffer position in the bitstream with the buffer metadata allows to later use that information to drop metadata for skipped buffers and to determine whether bitstream padding has to be applied. This patch also renames struct coda_timestamp to struct coda_buffer_meta to make clear that it contains more than only the buffer timestamp. Signed-off-by:
-
Philipp Zabel authored
This patch adds JPEG encoding and decoding support for CODA7541, using the BIT processor. Separate JPEG encoder and decoder video devices are created due to different streaming behaviour and different supported pixel formats. The hardware can not change subsampling on the fly, but encode and decode 4:2:2 subsampled JPEG images from and into this format. The CODA7541 JPEG decoder uses the bitstream buffer and thus can run without new buffers queued if there is a buffer in the bitstream. Since there is no standard way to store the colorspace used in JPEGs, and to make v4l2-compliance happy, the JPEG format always reports V4L2_COLORSPACE_JPEG. Signed-off-by:
Lucas Stach <l.stach@pengutronix.de> Signed-off-by:
-
Philipp Zabel authored
Add JPEG specific sequence initialization registers and bit definitions. Signed-off-by:
-
Philipp Zabel authored
This patch splits the encoder specific controls out of the main control setup function. This way each video device registers only relevant controls. Signed-off-by:
-
Philipp Zabel authored
Each video device descriptor determines the name, callback ops, and input and output formats on the corresponding video device. This simplifies coda_enum_fmt and coda_try_fmt a bit and will simplify adding separate video devices for JPEG codecs due to the slightly different behavior in the CodaDx6/CODA7542 case and a separate hardware unit on CODA960. Signed-off-by:
-
Philipp Zabel authored
We'll use this information to decide whether to request the JPEG IRQ later. Signed-off-by:
-
