Turn on CPU_SUPPORTS_CPUFREQ and MIPS_EXTERNAL_TIMER for BMIPS.
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Ran "make savedefconfig" to bring bmips_stb_defconfig up to date.
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

- s/freqnency/frequency/
- s/accomodating/accommodating/
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Some Kabylake desktop processors may not reach max turbo when running in
HWP mode, even if running under sustained 100% utilization.

This occurs when the HWP.EPP (Energy Performance Preference) is set to
"balance_power" (0x80) -- the default on most systems.

It occurs because the platform BIOS may erroneously enable an
energy-efficiency setting -- MSR_IA32_POWER_CTL BIT-EE, which is not
recommended to be enabled on this SKU.

On the failing systems, this BIOS issue was not discovered when the
desktop motherboard was tested with Windows, because the BIOS also
neglects to provide the ACPI/CPPC table, that Windows requires to enable
HWP, and so Windows runs in legacy P-state mode, where this setting has
no effect.

Linux' intel_pstate driver does not require ACPI/CPPC to enable HWP, and
so it runs in HWP mode, exposing this incorrect BIOS configuration.

There are several ways to address this problem.

First, Linux can also run in legacy P-state mode on this system.
As intel_pstate is how Linux enables HWP, booting with
"intel_pstate=disable"
will run in acpi-cpufreq/ondemand legacy p-state mode.

Or second, the "performance" governor can be used with intel_pstate,
which will modify HWP.EPP to 0.

Or third, starting in 4.10, the
/sys/devices/system/cpu/cpufreq/policy*/energy_performance_preference
attribute in can be updated from "balance_power" to "performance".

Or fourth, apply this patch, which fixes the erroneous setting of
MSR_IA32_POWER_CTL BIT_EE on this model, allowing the default
configuration to function as designed.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Len Brown <len.brown@intel.com>
Cc: 4.6+ <stable@vger.kernel.org> # 4.6+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

When HWP is active, turbo activation ratio is not used to calculate max
non turbo ratio. But on these systems the max non turbo ratio is decided
by config TDP settings.

This change removes usage of MSR_TURBO_ACTIVATION_RATIO for HWP systems,
instead directly use TDP ratios, when more than one TDPs are available.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Under HWP the performance limits are calculated using max_perf_pct
and min_perf_pct using possible performance, not available performance.
The available performance can be reduced by no_turbo setting. To make
compatible with legacy mode, use max/min performance percentage with
respect to available performance.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

When turbo is not disabled by BIOS, but user disabled from intel P-State
sysfs and changes max/min using cpufreq sysfs, the resultant frequency
is lower than what user requested.

The reason for this, when the perf limits are calculated in set_policy()
callback, they are with reference to max cpu frequency (turbo frequency
), but when enforced in the intel_pstate_get_min_max() they are with
reference to max available performance as documented in the intel_pstate
documentation (in this case max non turbo P-State).

This needs similar change as done in intel_cpufreq_verify_policy() for
passive mode. Set policy->cpuinfo.max_freq based on the turbo status.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Make it possible to change the operation mode of intel_pstate with
the help of a new sysfs attribute called "status".

There are three possible configurations that can be selected using
this attribute:

 "off"     - The driver is not in use at this time.
 "active"  - The driver works as a P-state governor (default).
 "passive" - The driver works as a regular cpufreq one and collaborates
             with the generic cpufreq governors (it sets P-states as
             requested by those governors).  [This is the same mode
             the driver can be started in by passing intel_pstate=passive
             in the kernel command line.]

The current setting is returned by reads from this attribute.  Writing
one of the above strings to it changes the operation mode as indicated
by that string, if possible.

If HW-managed P-states (HWP) feature is enabled, it is not possible
to change the driver's operation mode and attempts to write to this
attribute will fail.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Expose the intel_pstate's global sysfs attributes before registering
the driver to prepare for the addition of an attribute that also will
have to work if the driver is not registered.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Its not used anymore, remove it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

acpi_processor_ppc_notifier() can live without using CPUFREQ_START
(which is gonna be removed soon), as it is only used while setting
ignore_ppc to 0. This can be done with the help of "ignore_ppc < 0"
check alone. The notifier function anyway ignores all events except
CPUFREQ_ADJUST and dropping CPUFREQ_START wouldn't harm at all.

Once CPUFREQ_START event is removed from the cpufreq core,
acpi_processor_ppc_notifier() will get called only for CPUFREQ_NOTIFY or
CPUFREQ_ADJUST event. Drop the return statement from the first if block
to make sure we don't ignore any such events.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

In P8+, Workload Optimized Frequency(WOF) provides the capability to
boost the cpu frequency based on the utilization of the other cpus
running in the chip. The On-Chip-Controller(OCC) firmware will control
the achievability of these frequencies depending on the power headroom
available in the chip. Currently the ultra-turbo frequencies provided
by this feature are exported along with the turbo and sub-turbo
frequencies as scaling_available_frequencies. This patch will export
the ultra-turbo frequencies separately as scaling_boost_frequencies in
WOF enabled systems. This patch will add the boost sysfs file which
can be used to disable/enable ultra-turbo frequencies.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

The cpufreq core has gone though lots of updates in recent times, but on
many occasions the documentation wasn't updated along with the code.
This patch tries to catchup the documentation with the code.

Also add Rafael and Viresh as the contributors to the documentation.

Based on a patch from Claudio Scordino.
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

This patch doesn't change the content of the documentation, but rather
reformat it to make it more readable.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

This doesn't have any benefit apart from saving a small amount of memory
when it is disabled. The ifdef hackery in the code makes it dirty
unnecessarily.

Clean it up by removing the Kconfig option completely. Few defconfigs
are also updated and CONFIG_CPU_FREQ_STAT_DETAILS is replaced with
CONFIG_CPU_FREQ_STAT now in them, as users wanted stats to be enabled.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Those were added by:

commit fcd7af91 ("cpufreq: stats: handle cpufreq_unregister_driver()
and suspend/resume properly")

but aren't used anymore since:

commit 1aefc75b ("cpufreq: stats: Make the stats code non-modular").

Remove them. Also remove the redundant parameter to the respective
routines.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

I've seen this trigger twice now, where the i915_gem_object_to_ggtt()
call in intel_unpin_fb_obj() returns NULL, resulting in an oops
immediately afterwards as the (inlined) call to i915_vma_unpin_fence()
tries to dereference it.

It seems to be some race condition where the object is going away at
shutdown time, since both times happened when shutting down the X
server.  The call chains were different:

 - VT ioctl(KDSETMODE, KD_TEXT):

    intel_cleanup_plane_fb+0x5b/0xa0 [i915]
    drm_atomic_helper_cleanup_planes+0x6f/0x90 [drm_kms_helper]
    intel_atomic_commit_tail+0x749/0xfe0 [i915]
    intel_atomic_commit+0x3cb/0x4f0 [i915]
    drm_atomic_commit+0x4b/0x50 [drm]
    restore_fbdev_mode+0x14c/0x2a0 [drm_kms_helper]
    drm_fb_helper_restore_fbdev_mode_unlocked+0x34/0x80 [drm_kms_helper]
    drm_fb_helper_set_par+0x2d/0x60 [drm_kms_helper]
    intel_fbdev_set_par+0x18/0x70 [i915]
    fb_set_var+0x236/0x460
    fbcon_blank+0x30f/0x350
    do_unblank_screen+0xd2/0x1a0
    vt_ioctl+0x507/0x12a0
    tty_ioctl+0x355/0xc30
    do_vfs_ioctl+0xa3/0x5e0
    SyS_ioctl+0x79/0x90
    entry_SYSCALL_64_fastpath+0x13/0x94

 - i915 unpin_work workqueue:

    intel_unpin_work_fn+0x58/0x140 [i915]
    process_one_work+0x1f1/0x480
    worker_thread+0x48/0x4d0
    kthread+0x101/0x140

and this patch purely papers over the issue by adding a NULL pointer
check and a WARN_ON_ONCE() to avoid the oops that would then generally
make the machine unresponsive.

Other callers of i915_gem_object_to_ggtt() seem to also check for the
returned pointer being NULL and warn about it, so this clearly has
happened before in other places.

[ Reported it originally to the i915 developers on Jan 8, applying the
  ugly workaround on my own now after triggering the problem for the
  second time with no feedback.

  This is likely to be the same bug reported as

     https://bugs.freedesktop.org/show_bug.cgi?id=98829
     https://bugs.freedesktop.org/show_bug.cgi?id=99134

  which has a patch for the underlying problem, but it hasn't gotten to
  me, so I'm applying the workaround. ]

Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull two parisc fixes from Helge Deller:
 "One fix to avoid usage of BITS_PER_LONG in user-space exported swab.h
  header which breaks compiling qemu, and one trivial fix for printk
  continuation in the parisc parport driver"

* 'parisc-4.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Don't use BITS_PER_LONG in userspace-exported swab.h header
  parisc, parport_gsc: Fixes for printk continuation lines

Pull i2c fixes from Wolfram Sang:
 "Two I2C driver bugfixes.

  The 'VLLS mode support' patch should have been entitled 'reconfigure
  pinctrl after suspend' to make the bugfix more clear. Sorry, I missed
  that, yet didn't want to rebase"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: imx-lpi2c: add VLLS mode support
  i2c: i2c-cadence: Initialize configuration before probing devices

In swab.h the "#if BITS_PER_LONG > 32" breaks compiling userspace programs if
BITS_PER_LONG is #defined by userspace with the sizeof() compiler builtin.

Solve this problem by using __BITS_PER_LONG instead.  Since we now
#include asm/bitsperlong.h avoid further potential userspace pollution
by moving the #define of SHIFT_PER_LONG to bitops.h which is not
exported to userspace.

This patch unbreaks compiling qemu on hppa/parisc.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org>

Signed-off-by: Helge Deller <deller@gmx.de>

Pull NFS client bugfixes from Trond Myklebust:
 "Stable patches:
   - NFSv4.1: Fix a deadlock in layoutget
   - NFSv4 must not bump sequence ids on NFS4ERR_MOVED errors
   - NFSv4 Fix a regression with OPEN EXCLUSIVE4 mode
   - Fix a memory leak when removing the SUNRPC module

  Bugfixes:
   - Fix a reference leak in _pnfs_return_layout"

* tag 'nfs-for-4.10-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  pNFS: Fix a reference leak in _pnfs_return_layout
  nfs: Fix "Don't increment lock sequence ID after NFS4ERR_MOVED"
  SUNRPC: cleanup ida information when removing sunrpc module
  NFSv4.0: always send mode in SETATTR after EXCLUSIVE4
  nfs: Don't increment lock sequence ID after NFS4ERR_MOVED
  NFSv4.1: Fix a deadlock in layoutget

Pull MD fixes from Shaohua Li:
 "This fixes several corner cases for raid5 cache, which is merged into
  this cycle"

* tag 'md/4.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
  md/r5cache: disable write back for degraded array
  md/r5cache: shift complex rmw from read path to write path
  md/r5cache: flush data only stripes in r5l_recovery_log()
  md/raid5: move comment of fetch_block to right location
  md/r5cache: read data into orig_page for prexor of cached data
  md/raid5-cache: delete meaningless code

Pull arm64 fix from Catalin Marinas:
 "Fix kernel panic on ACPI-based systems where CPU capacity description
  is not currently handled"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: skip register_cpufreq_notifier on ACPI-based systems

Pull ARC fixes from Vineet Gupta:
 "Hopefully last set of changes for ARC for 4.10:

   - fix for unaligned access emulation corner case

   - fix for udelay loop inline asm regression

   - fix irq affinity finally for AXS103 board [Yuriy]

   - final fixes for setting IO-coherency sanely in SMP"

* tag 'arc-4.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: [arcompact] handle unaligned access delay slot corner case
  ARCv2: smp-boot: wake_flag polling by non-Masters needs to be uncached
  ARC: smp-boot: Decouple Non masters waiting API from jump to entry point
  ARCv2: MCIP: update the BCR per current changes
  ARC: udelay: fix inline assembler by adding LP_COUNT to clobber list
  ARCv2: MCIP: Deprecate setting of affinity in Device Tree

Pull networking fixes from David Miller:

 1) GTP fixes from Andreas Schultz (missing genl module alias, clear IP
    DF on transmit).

 2) Netfilter needs to reflect the fwmark when sending resets, from Pau
    Espin Pedrol.

 3) nftable dump OOPS fix from Liping Zhang.

 4) Fix erroneous setting of VIRTIO_NET_HDR_F_DATA_VALID on transmit,
    from Rolf Neugebauer.

 5) Fix build error of ipt_CLUSTERIP when procfs is disabled, from Arnd
    Bergmann.

 6) Fix regression in handling of NETIF_F_SG in harmonize_features(),
    from Eric Dumazet.

 7) Fix RTNL deadlock wrt. lwtunnel module loading, from David Ahern.

 8) tcp_fastopen_create_child() needs to setup tp->max_window, from
    Alexey Kodanev.

 9) Missing kmemdup() failure check in ipv6 segment routing code, from
    Eric Dumazet.

10) Don't execute unix_bind() under the bindlock, otherwise we deadlock
    with splice. From WANG Cong.

11) ip6_tnl_parse_tlv_enc_lim() potentially reallocates the skb buffer,
    therefore callers must reload cached header pointers into that skb.
    Fix from Eric Dumazet.

12) Fix various bugs in legacy IRQ fallback handling in alx driver, from
    Tobias Regnery.

13) Do not allow lwtunnel drivers to be unloaded while they are
    referenced by active instances, from Robert Shearman.

14) Fix truncated PHY LED trigger names, from Geert Uytterhoeven.

15) Fix a few regressions from virtio_net XDP support, from John
    Fastabend and Jakub Kicinski.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (102 commits)
  ISDN: eicon: silence misleading array-bounds warning
  net: phy: micrel: add support for KSZ8795
  gtp: fix cross netns recv on gtp socket
  gtp: clear DF bit on GTP packet tx
  gtp: add genl family modules alias
  tcp: don't annotate mark on control socket from tcp_v6_send_response()
  ravb: unmap descriptors when freeing rings
  virtio_net: reject XDP programs using header adjustment
  virtio_net: use dev_kfree_skb for small buffer XDP receive
  r8152: check rx after napi is enabled
  r8152: re-schedule napi for tx
  r8152: avoid start_xmit to schedule napi when napi is disabled
  r8152: avoid start_xmit to call napi_schedule during autosuspend
  net: dsa: Bring back device detaching in dsa_slave_suspend()
  net: phy: leds: Fix truncated LED trigger names
  net: phy: leds: Break dependency of phy.h on phy_led_triggers.h
  net: phy: leds: Clear phy_num_led_triggers on failure to avoid crash
  net-next: ethernet: mediatek: change the compatible string
  Documentation: devicetree: change the mediatek ethernet compatible string
  bnxt_en: Fix RTNL lock usage on bnxt_get_port_module_status().
  ...

Pull xfs uodates from Darrick Wong:
 "I have some more fixes this week: better input validation, corruption
  avoidance, build fixes, memory leak fixes, and a couple from Christoph
  to avoid an ENOSPC failure.

  Summary:
   - Fix race conditions in the CoW code
   - Fix some incorrect input validation checks
   - Avoid crashing fs by running out of space when freeing inodes
   - Fix toctou race wrt whether or not an inode has an attr
   - Fix build error on arm
   - Fix page refcount corruption when readahead fails
   - Don't corrupt userspace in the bmap ioctl"

* tag 'xfs-for-linus-4.10-rc6-5' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: prevent quotacheck from overloading inode lru
  xfs: fix bmv_count confusion w/ shared extents
  xfs: clear _XBF_PAGES from buffers when readahead page
  xfs: extsize hints are not unlikely in xfs_bmap_btalloc
  xfs: remove racy hasattr check from attr ops
  xfs: use per-AG reservations for the finobt
  xfs: only update mount/resv fields on success in __xfs_ag_resv_init
  xfs: verify dirblocklog correctly
  xfs: fix COW writeback race

Pull btrfs updates from Chris Mason:
 "Some fixes that we've collected from the list.

  We still have one more pending to nail down a regression in lzo
  compression, but I wanted to get this batch out the door"

* 'for-linus-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: remove ->{get, set}_acl() from btrfs_dir_ro_inode_operations
  Btrfs: disable xattr operations on subvolume directories
  Btrfs: remove old tree_root case in btrfs_read_locked_inode()
  Btrfs: fix truncate down when no_holes feature is enabled
  Btrfs: Fix deadlock between direct IO and fast fsync
  btrfs: fix false enospc error when truncating heavily reflinked file

Pull block fixes from Jens Axboe:
 "A set of fixes for this series. This contains:

   - Set of fixes for the nvme target code

   - A revert of patch from this merge window, causing a regression with
     WRITE_SAME on iSCSI targets at least.

   - A fix for a use-after-free in the new O_DIRECT bdev code.

   - Two fixes for the xen-blkfront driver"

* 'for-linus' of git://git.kernel.dk/linux-block:
  Revert "sd: remove __data_len hack for WRITE SAME"
  nvme-fc: use blk_rq_nr_phys_segments
  nvmet-rdma: Fix missing dma sync to nvme data structures
  nvmet: Call fatal_error from keep-alive timout expiration
  nvmet: cancel fatal error and flush async work before free controller
  nvmet: delete controllers deletion upon subsystem release
  nvmet_fc: correct logic in disconnect queue LS handling
  block: fix use after free in __blkdev_direct_IO
  xen-blkfront: correct maximum segment accounting
  xen-blkfront: feature flags handling adjustments

Pull rdma fixes from Doug Ledford:
 "Second round of -rc fixes for 4.10.

  This -rc cycle has been slow for the rdma subsystem. I had already
  sent you the first batch before the Holiday break. After that, we kept
  only getting a few here or there. Up until this week, when I got a
  drop of 13 to one driver (qedr). So, here's the -rc patches I have. I
  currently have none held in reserve, so unless something new comes in,
  this is it until the next merge window opens.

  Summary:

   - series of iw_cxgb4 fixes to make it work with the drain cq API

   - one or two patches each to: srp, iser, cxgb3, vmw_pvrdma, umem,
     rxe, and ipoib

   - one big series (13 patches) for the new qedr driver"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (27 commits)
  RDMA/cma: Fix unknown symbol when CONFIG_IPV6 is not enabled
  IB/rxe: Prevent from completer to operate on non valid QP
  IB/rxe: Fix rxe dev insertion to rxe_dev_list
  IB/umem: Release pid in error and ODP flow
  RDMA/qedr: Dispatch port active event from qedr_add
  RDMA/qedr: Fix and simplify memory leak in PD alloc
  RDMA/qedr: Fix RDMA CM loopback
  RDMA/qedr: Fix formatting
  RDMA/qedr: Mark three functions as static
  RDMA/qedr: Don't reset QP when queues aren't flushed
  RDMA/qedr: Don't spam dmesg if QP is in error state
  RDMA/qedr: Remove CQ spinlock from CM completion handlers
  RDMA/qedr: Return max inline data in QP query result
  RDMA/qedr: Return success when not changing QP state
  RDMA/qedr: Add uapi header qedr-abi.h
  RDMA/qedr: Fix MTU returned from QP query
  RDMA/core: Add the function ib_mtu_int_to_enum
  IB/vmw_pvrdma: Fix incorrect cleanup on pvrdma_pci_probe error path
  IB/vmw_pvrdma: Don't leak info from alloc_ucontext
  IB/cxgb3: fix misspelling in header guard
  ...

Pull s390 fixes from Martin Schwidefsky:
 "Another two bug fixes:

   - ptrace partial write information leak

   - a guest page hinting regression introduced with v4.6"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/mm: Fix cmma unused transfer from pgste into pte
  s390/ptrace: Preserve previous registers for short regset write

Merge branch 'stable/for-linus-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb

Pull swiotlb fix from Konrad Rzeszutek Wilk:
 "An ARM fix in the Xen SWIOTLB - mainly the translation of physical to
  bus addresses was done just a tad too late"

* 'stable/for-linus-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
  swiotlb-xen: update dev_addr after swapping pages

Pull VFIO fix from Alex Williamson:
 "mdev IOMMU groups are not yet compatible with the powerpc SPAPR IOMMU
  backend, detect and fail group attach (Greg Kurz)"

* tag 'vfio-v4.10-rc6' of git://github.com/awilliam/linux-vfio:
  vfio/spapr: fail tce_iommu_attach_group() when iommu_data is null

If IPV6 has not been enabled in the underlying kernel, we must avoid
calling IPV6 procedures in rdma_cm.ko.

This requires using "IS_ENABLED(CONFIG_IPV6)" in "if" statements
surrounding any code which calls external IPV6 procedures.

In the instance fixed here, procedure cma_bind_addr() called
ipv6_addr_type() -- which resulted in calling external procedure
__ipv6_addr_type().

Fixes: 6c26a771 ("RDMA/cma: fix IPv6 address resolution")
Cc: <stable@vger.kernel.org> # v4.2+
Cc: Spencer Baugh <sbaugh@catern.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Merge branch 'stable/for-jens-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen into for-linus

Konrad writes:

Please pull in your 'for-linus' branch two little fixes for Xen
block front:

One fix is for handling the XEN_PAGE_SIZE != PAGE_SIZE (4KB vs 64KB
on ARM for example) mishandling while the other is fixing
the accounting for the configuration changes.

After emulating an unaligned access in delay slot of a branch, we
pretend as the delay slot never happened - so return back to actual
branch target (or next PC if branch was not taken).

Curently we did this by handling STATUS32.DE, we also need to clear the
BTA.T bit, which is disregarded when returning from original misaligned
exception, but could cause weirdness if it took the interrupt return
path (in case interrupt was acive too)

One ARC700 customer ran into this when enabling unaligned access fixup
for kernel mode accesses as well

Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Pull media fixes from Mauro Carvalho Chehab:

 - fix a regression on tvp5150 causing failures at input selection and
   image glitches

 - CEC was moved out of staging for v4.10. Fix some bugs on it while not
   too late

 - fix a regression on pctv452e caused by VM stack changes

 - fix suspend issued with smiapp

 - fix a regression on cobalt driver

 - fix some warnings and Kconfig issues with some random configs.

* tag 'media/v4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] s5k4ecgx: select CRC32 helper
  [media] dvb: avoid warning in dvb_net
  [media] v4l: tvp5150: Don't override output pinmuxing at stream on/off time
  [media] v4l: tvp5150: Fix comment regarding output pin muxing
  [media] v4l: tvp5150: Reset device at probe time, not in get/set format handlers
  [media] pctv452e: move buffer to heap, no mutex
  [media] media/cobalt: use pci_irq_allocate_vectors
  [media] cec: fix race between configuring and unconfiguring
  [media] cec: move cec_report_phys_addr into cec_config_thread_func
  [media] cec: replace cec_report_features by cec_fill_msg_report_features
  [media] cec: update log_addr[] before finishing configuration
  [media] cec: CEC_MSG_GIVE_FEATURES should abort for CEC version < 2
  [media] cec: when canceling a message, don't overwrite old status info
  [media] cec: fix report_current_latency
  [media] smiapp: Make suspend and resume functions __maybe_unused
  [media] smiapp: Implement power-on and power-off sequences without runtime PM

Pull MMC fix from Ulf Hansson:
 "MMC host: fix runtime PM resume path in dw_mmc"

* tag 'mmc-v4.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: dw_mmc: force setup bus if active slots exist