- 11 Nov, 2011 40 commits
-
-
Oliver Neukum authored
commit 2394d67e upstream. The new runtime PM code has shown that many webcams suffer from a race condition that may crash them upon resume. Runtime PM is especially prone to show the problem because it retains power to the cameras at all times. However system suspension may also crash the devices and retain power to the devices. The only way to solve this problem without races is in usbcore with the RESET_RESUME quirk. Signed-off-by:
Oliver Neukum <oneukum@suse.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Denis Pershin authored
commit 65e52f41 upstream. here is the patch to support Owen SI-30 device. This is a pulse counter controller. http://www.owen.ru/en/catalog/93788515 usb-drivers output: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=02(commc) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=03eb ProdID=0030 Rev=01.01 C: #Ifs= 2 Cfg#= 1 Atr=c0 MxPwr=0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=02 Prot=00 Driver=cdc_acm I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_acm This patch is installed on my home system which receives data from this controller connected to cold water counter. Signed-off-by:
Denis Pershin <dyp@perchine.com> Signed-off-by:
-
Serge Hallyn authored
commit aec01c58 upstream. Alan Stern points out that after spin_unlock(&ps->lock) there is no guarantee that ps->pid won't be freed. Since kill_pid_info_as_uid() is called after the spin_unlock(), the pid passed to it must be pinned. Reported-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Serge Hallyn <serge.hallyn@canonical.com> Signed-off-by:
-
Matthias Dellweg authored
commit 393cbb51 upstream. In the usb printer class specific request get_device_id the value of wIndex is (interface << 8 | altsetting) instead of just interface. This enables the detection of some printers with libusb. Acked-by:
Matthias Dellweg <2500@gmx.de> Signed-off-by:
-
Fabian Godehardt authored
commit 8582d861 upstream. The allocated chardevice region range is only 1 device but on unregister it currently tries to deregister 2. Found this while doing a insmod/rmmod/insmod/rm... of the module which seemed to eat major numbers. Signed-off-by:
Fabian Godehardt <fg@emlix.com> Signed-off-by:
-
Matthew Garrett authored
commit a8b43c00 upstream. At least some OHCI hardware (such as the MCP89) fails to flag any change in the host status register or the port status registers when receiving a remote wakeup while in D3 state. This results in the controller being resumed but no device state change being noticed, at which point the controller is put back to sleep again. Since there doesn't seem to be any reliable way to identify the state change, just unconditionally resume the hub. It'll be put back to sleep in the near future anyway if there are no active devices attached to it. Signed-off-by:
Matthew Garrett <mjg@redhat.com> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Luben Tuikov authored
commit e16da02f upstream. This patch solves two things: 1) Enables autosense emulation code to correctly interpret descriptor format sense data, and 2) Fixes a bug whereby the autosense emulation code would overwrite descriptor format sense data with SENSE KEY HARDWARE ERROR in fixed format, to incorrectly look like this: Oct 21 14:11:07 localhost kernel: sd 7:0:0:0: [sdc] Sense Key : Recovered Error [current] [descriptor] Oct 21 14:11:07 localhost kernel: Descriptor sense data with sense descriptors (in hex): Oct 21 14:11:07 localhost kernel: 72 01 04 1d 00 00 00 0e 09 0c 00 00 00 00 00 00 Oct 21 14:11:07 localhost kernel: 00 4f 00 c2 00 50 Oct 21 14:11:07 localhost kernel: sd 7:0:0:0: [sdc] ASC=0x4 ASCQ=0x1d Signed-off-by:
Luben Tuikov <ltuikov@yahoo.com> Acked-by:
Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by:
-
Johannes Stezenbach authored
commit 236c448c upstream. Report the number of dropped packets instead of zero when using the binary usbmon interface with tcpdump. # tcpdump -i usbmon1 -w dump tcpdump: listening on usbmon1, link-type USB_LINUX_MMAPPED (USB with padded Linux header), capture size 65535 bytes ^C2155 packets captured 2155 packets received by filter 1019 packets dropped by kernel Signed-off-by:
Johannes Stezenbach <js@sig21.net> Signed-off-by:
-
Antonio Ospite authored
commit 488bc35b upstream. Depending on the implementation of the hardware blinking function in blink_set(), the led can support hardware blinking for some values of delay_on and delay_off and fall-back to software blinking for some other values. Turning off the blink_timer unconditionally before starting to blink make sure that a sequence like: OFF hardware blinking software blinking hardware blinking does not leave the software blinking timer active. Signed-off-by:
Antonio Ospite <ospite@studenti.unina.it> Reviewed-by:
Johannes Berg <johannes@sipsolutions.net> Cc: Richard Purdie <rpurdie@rpsys.net> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Antonio Ospite authored
commit 6123b0e2 upstream. When calling the hardware blinking function implemented by blink_set(), the delay_on and delay_off values are not preserved across calls. Fix that and make the "timer" trigger work as expected when hardware blinking is available. BEFORE the fix: $ cd /sys/class/leds/someled $ echo timer > trigger $ cat delay_on delay_off 0 0 $ echo 100 > delay_on $ cat delay_on delay_off 0 0 $ echo 100 > delay_off $ cat delay_on delay_off 0 0 AFTER the fix: $ cd /sys/class/leds/someled $ echo timer > trigger $ cat delay_on delay_off 0 0 $ echo 100 > delay_on $ cat delay_on delay_off 100 0 $ echo 100 > delay_off $ cat delay_on delay_off 100 100 Signed-off-by:
-
Nelson Elhage authored
commit d8805e63 upstream. epoll can acquire recursively acquire ep->mtx on multiple "struct eventpoll"s at once in the case where one epoll fd is monitoring another epoll fd. This is perfectly OK, since we're careful about the lock ordering, but it causes spurious lockdep warnings. Annotate the recursion using mutex_lock_nested, and add a comment explaining the nesting rules for good measure. Recent versions of systemd are triggering this, and it can also be demonstrated with the following trivial test program: --------------------8<-------------------- int main(void) { int e1, e2; struct epoll_event evt = { .events = EPOLLIN }; e1 = epoll_create1(0); e2 = epoll_create1(0); epoll_ctl(e1, EPOLL_CTL_ADD, e2, &evt); return 0; } --------------------8<-------------------- Reported-by:
Paul Bolle <pebolle@tiscali.nl> Tested-by:
Nelson Elhage <nelhage@nelhage.com> Acked-by:
Jason Baron <jbaron@redhat.com> Cc: Dave Jones <davej@redhat.com> Cc: Davide Libenzi <davidel@xmailserver.org> Signed-off-by:
-
Josh Stone authored
commit 315eb8a2 upstream. When compiling an i386_defconfig kernel with gcc-4.6.1-9.fc15.i686, I noticed a warning about the asm operand for test_bit in kprobes' can_boost. I discovered that this caused only the first long of twobyte_is_boostable[] to be output. Jakub filed and fixed gcc PR50571 to correct the warning and this output issue. But to solve it for less current gcc, we can make kprobes' twobyte_is_boostable[] non-const, and it won't be optimized out. Before: CC arch/x86/kernel/kprobes.o In file included from include/linux/bitops.h:22:0, from include/linux/kernel.h:17, from [...]/arch/x86/include/asm/percpu.h:44, from [...]/arch/x86/include/asm/current.h:5, from [...]/arch/x86/include/asm/processor.h:15, from [...]/arch/x86/include/asm/atomic.h:6, from include/linux/atomic.h:4, from include/linux/mutex.h:18, from include/linux/notifier.h:13, from include/linux/kprobes.h:34, from arch/x86/kernel/kprobes.c:43: [...]/arch/x86/include/asm/bitops.h: In function ‘can_boost.part.1’: [...]/arch/x86/include/asm/bitops.h:319:2: warning: use of memory input without lvalue in asm operand 1 is deprecated [enabled by default] $ objdump -rd arch/x86/kernel/kprobes.o | grep -A1 -w bt 551: 0f a3 05 00 00 00 00 bt %eax,0x0 554: R_386_32 .rodata.cst4 $ objdump -s -j .rodata.cst4 -j .data arch/x86/kernel/kprobes.o arch/x86/kernel/kprobes.o: file format elf32-i386 Contents of section .data: 0000 48000000 00000000 00000000 00000000 H............... Contents of section .rodata.cst4: 0000 4c030000 L... Only a single long of twobyte_is_boostable[] is in the object file. After, without the const on twobyte_is_boostable: $ objdump -rd arch/x86/kernel/kprobes.o | grep -A1 -w bt 551: 0f a3 05 20 00 00 00 bt %eax,0x20 554: R_386_32 .data $ objdump -s -j .rodata.cst4 -j .data arch/x86/kernel/kprobes.o arch/x86/kernel/kprobes.o: file format elf32-i386 Contents of section .data: 0000 48000000 00000000 00000000 00000000 H............... 0010 00000000 00000000 00000000 00000000 ................ 0020 4c030000 0f000200 ffff0000 ffcff0c0 L............... 0030 0000ffff 3bbbfff8 03ff2ebb 26bb2e77 ....;.......&..w Now all 32 bytes are output into .data instead. Signed-off-by:
Josh Stone <jistone@redhat.com> Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Cc: Jakub Jelinek <jakub@redhat.com> Signed-off-by:
-
Jack Steiner authored
commit 6a469e46 upstream. This is a workaround for a UV2 hub bug that affects the format of system global addresses. The GRU API for UV2 was inadvertently broken by a hardware change. The format of the physical address used for TLB dropins and for addresses used with instructions running in unmapped mode has changed. This change was not documented and became apparent only when diags failed running on system simulators. For UV1, TLB and GRU instruction physical addresses are identical to socket physical addresses (although high NASID bits must be OR'ed into the address). For UV2, socket physical addresses need to be converted. The NODE portion of the physical address needs to be shifted so that the low bit is in bit 39 or bit 40, depending on an MMR value. It is not yet clear if this bug will be fixed in a silicon respin. If it is fixed, the hub revision will be incremented & the workaround disabled. Signed-off-by:
Jack Steiner <steiner@sgi.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: "H. Peter Anvin" <hpa@zytor.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Nicholas Bellinger authored
commit 6b20fa9a upstream. This patch fixes a bug with the handling of REPORT TARGET PORT GROUPS containing a smaller allocation length than the payload requires causing memory writes beyond the end of the buffer. This patch checks for the minimum 4 byte length for the response payload length, and also checks upon each loop of T10_ALUA(su_dev)->tg_pt_gps_list to ensure the Target port group and Target port descriptor list is able to fit into the remaining allocation length. If the response payload exceeds the allocation length length, then rd_len is still increments to indicate to the initiator that the payload has been truncated. Reported-by:
Roland Dreier <roland@purestorage.com> Signed-off-by:
Nicholas Bellinger <nab@risingtidesystems.com> Signed-off-by:
-
David Henningsson authored
commit cc667a72 upstream. The revision 0x100300 was found for ALC662. It seems to work well with patch_alc662. BugLink: http://bugs.launchpad.net/bugs/877373Tested-by:
Shengyao Xue <Shengyao.xue@canonical.com> Signed-off-by:
David Henningsson <david.henningsson@canonical.com> Acked-by:
Kailang Yang <kailang@realtek.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Charles Chin authored
commit 6c5c04e5 upstream. The purpose of this patch is to remove a section of "bad" code that assigns the last DAC to ports E or F in order to support notebooks with docking in earlier days, around ALSA 1.0.19 - 21. This is not necessary now and actually breaks some configurations that use these ports as other devices. This have been tested on several different configurations to make sure that it is working for different combinations. Signed-off-by:
Charles Chin <Charles.Chin@idt.com> Signed-off-by:
-
Jeff Skirvin authored
commit 983d3fdd upstream. Needed to jump to scic_lock unlock. Also spotted by coccicheck. Signed-off-by:
Jeff Skirvin <jeffrey.d.skirvin@intel.com> Signed-off-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
James Bottomley <JBottomley@Parallels.com> Signed-off-by:
-
Dan Williams authored
commit 54b5e3a4 upstream. Kill the local smp response buffer. Besides being unnecessary, it is too small (currently truncates responses to 60 bytes). The mid-layer will have already allocated a sufficiently sized buffer, just kmap and copy into it directly. Reported-by:
Derick Marks <derick.w.marks@intel.com> Tested-by:
-
Jack Wang authored
commit bb041a0e upstream. Libsas forget to set the sas_address and device type of rphy lead to file under /sys/class/sas_x show wrong value, fix that. Signed-off-by:
Jack Wang <jack_wang@usish.com> Tested-by:
Crystal Yu <crystal_yu@usish.com> Signed-off-by:
-
Anton Blanchard authored
commit 5d7c20b7 upstream. During kdump testing I noticed timeouts when initialising each IPR adapter. While the driver has logic to detect an adapter in an indeterminate state, it wasn't triggering and each adapter went through a 5 minute timeout before finally going operational. Some analysis showed the needs_hard_reset flag wasn't getting set. We can check the reset_devices kernel parameter which is set by kdump and force a full reset. This fixes the problem. Signed-off-by:
Anton Blanchard <anton@samba.org> Acked-by:
Brian King <brking@linux.vnet.ibm.com> Signed-off-by:
-
adam radford authored
commit f575c5d3 upstream. The following patch for megaraid_sas will fix a potential bad pointer access in megasas_reset_timer(), when a MegaRAID 9265/9285 or 9360/9380 gets a timeout. megasas_build_io_fusion() sets SCp.ptr to be a struct megasas_cmd_fusion *, but then megasas_reset_timer() was casting SCp.ptr to be a struct megasas_cmd *, then trying to access cmd->instance, which is invalid. Just loading instance from scmd->device->host->hostdata in megasas_reset_timer() fixes the issue. Signed-off-by:
Adam Radford <aradford@gmail.com> Signed-off-by:
-
Josh Boyer authored
commit 3e309cdf upstream. Commit 15bed0f2 added a quirk for the e823 Ricoh card reader to lower the base frequency. However, the quirk first checks to see if the proprietary MMC controller is disabled, and returns if so. On some devices, such as the Lenovo X220, the MMC controller is already disabled by firmware it seems, but the frequency change is still needed so sdhci-pci can talk to the cards. Since the MMC controller is disabled, the frequency fixup was never being run on these machines. This moves the e823 check above the MMC controller check so that it always gets run. This fixes https://bugzilla.redhat.com/show_bug.cgi?id=722509Signed-off-by:
Josh Boyer <jwboyer@redhat.com> Signed-off-by:
Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by:
-
Andrei Warkentin authored
commit 5238acbe upstream. f39b2dd9 ("mmc: core: Bus width testing needs to handle suspend/resume") added code to only compare read-only ext_csd fields in bus width testing code, yet it's comparing some fields that are never set. The affected fields are ext_csd.raw_erased_mem_count and ext_csd.raw_partition_support. Signed-off-by:
Andrei Warkentin <andrey.warkentin@gmail.com> Acked-by:
Philip Rakity <prakity@marvell.com> Signed-off-by:
Chris Ball <cjb@laptop.org> Signed-off-by:
-
Ulf Hansson authored
commit 7f7e4129 upstream. During a rescan operation mmc_attach(sd|mmc|sdio) functions are called. The error handling in these function can trigger a detach of the bus, which also meant a power off. This is not notified by the rescan operation which then continues to the next attach function. If a power off has been done, the framework must never send any new commands to the host driver, without first doing a new power up. This will most likely trigger any host driver to hang. Moving power off out of detach and instead handle power off separately when it is actually needed, solves the issue. Signed-off-by:
Ulf Hansson <ulf.hansson@stericsson.com> Acked-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Jean Delvare authored
commit 286e0c94 upstream. Commit 9b9fe724 accidentally used RADEON_GPIO_EN_* where RADEON_GPIO_MASK_* was intended. This caused improper initialization of I2C buses, mostly visible when setting i2c_algo_bit.bit_test=1. Using the right constants fixes the problem. Signed-off-by:
Jean Delvare <jdelvare@suse.de> Reviewed-by:
Alex Deucher <alexander.deucher@amd.com> Cc: Jerome Glisse <j.glisse@gmail.com> Signed-off-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
-
Alex Deucher authored
commit d0d0a225 upstream. When force == false, we don't do load detection in the connector detect functions. Unforunately, we also return the previous connector state so we never get disconnect events for DVI-I, DVI-A, or VGA. Save whether we detected the monitor via load detection previously and use that to determine whether we return the previous state or not. Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=41561Signed-off-by:
-
Alex Deucher authored
commit 5f0a2612 upstream. DVI-D and HDMI-A are digital only, so there's no need to attempt analog load detect. Also, skip bail before the !force check, or we fail to get a disconnect events. The next patches in the series attempt to fix disconnect events for connectors with analog support (DVI-I, HDMI-B, DVI-A). Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=41561Signed-off-by:
-
Takashi Iwai authored
commit f52c619a upstream. The commit 47356eb6 introduced a mechanism to record the backlight level only at disabling time, but it also introduced a regression. Since intel_lvds_enable() may be called without disabling (e.g. intel_lvds_commit() calls it unconditionally), the backlight gets back to the last recorded value. For example, this happens when you dim the backlight, close the lid and open the lid, then the backlight suddenly goes to the brightest. This patch fixes the bug by recording the backlight level always when changed via intel_panel_set_backlight(). And, intel_panel_{enable|disable}_backlight() call the internal function not to update the recorded level wrongly. Signed-off-by:
Keith Packard <keithp@keithp.com> Signed-off-by:
-
Keith Packard authored
commit 8c241fef upstream. Talking to the eDP DDC channel requires that the panel be powered up. Wrap both the EDID and modes fetch code with calls to turn the vdd power on and back off. Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
-
Andiry Xu authored
commit 7e393a83 upstream. Setting the chain (CH) bit in the link TRB of isochronous transfer rings is required by AMD 0.96 xHCI host controller to successfully transverse multi-TRB TD that span through different memory segments. When a Missed Service Error event occurs, if the chain bit is not set in the link TRB and the host skips TDs which just across a link TRB, the host may falsely recognize the link TRB as a normal TRB. You can see this may cause big trouble - the host does not jump to the right address which is pointed by the link TRB, but continue fetching the memory which is after the link TRB address, which may not even belong to the host, and the result cannot be predicted. This causes some big problems. Without the former patch I sent: "xHCI: prevent infinite loop when processing MSE event", the system may hang. With that patch applied, system does not hang, but the host still access wrong memory address and isoc transfer will fail. With this patch, isochronous transfer works as expected. This patch should be applied to kernels as old as 2.6.36, which was when the first isochronous support was added for the xHCI host controller. Signed-off-by:
Andiry Xu <andiry.xu@amd.com> Signed-off-by:
Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by:
-
Kautuk Consul authored
commit 0e6c7f74 upstream. There are 2 situations wherein the xhci_ring* might not get freed: - When xhci_ring_alloc() -> xhci_segment_alloc() returns NULL and we goto the fail: label in xhci_ring_alloc. In this case, the ring will not get kfreed. - When the num_segs argument to xhci_ring_alloc is passed as 0 and we try to free the rung after that. ( This doesn't really happen as of now in the code but we seem to be entertaining num_segs=0 in xhci_ring_alloc ) This should be backported to kernels as old as 2.6.31. Signed-off-by:
Kautuk Consul <consul.kautuk@gmail.com> Signed-off-by:
-
Alan Stern authored
commit 68aa95d5 upstream. This patch (as1489) works around a hardware bug in MosChip EHCI controllers. Evidently when one of these controllers increments the frame-index register, it changes the three low-order bits (the microframe counter) before changing the higher order bits (the frame counter). If the register is read at just the wrong time, the value obtained is too low by 8. When the appropriate quirk flag is set, we work around this problem by reading the frame-index register a second time if the first value's three low-order bits are all 0. This gives the hardware a chance to finish updating the register, yielding the correct value. Signed-off-by:
Jason N Pitt <jpitt@fhcrc.org> Signed-off-by:
-
Harro Haan authored
commit 276532ba upstream. The Kirkwood gave an unaligned memory access error on line 742 of drivers/usb/host/echi-hcd.c: "ehci->last_periodic_enable = ktime_get_real();" Signed-off-by:
Harro Haan <hrhaan@gmail.com> Acked-by:
-
Matthieu CASTET authored
commit 2093c6b4 upstream. This allow to clean duplicated code in most of SOC driver. Signed-off-by:
Matthieu CASTET <castet.matthieu@free.fr> Acked-by:
-
Ning Jiang authored
commit 94abc56f upstream. The following patch removed uart_change_pm() in uart_resume_port(): commit 5933a161 Author: Yin Kangkai <kangkai.yin@linux.intel.com> serial-core: reset the console speed on resume It will break the pxa serial driver when the system resumes from suspend mode as it will try to set baud rate divider register in set_termios but with clock off. The register value can not be set correctly on some platform if the clock is disabled. The pxa driver will check the value and report the following warning: ------------[ cut here ]------------ WARNING: at drivers/tty/serial/pxa.c:545 serial_pxa_set_termios+0x1dc/0x250() Modules linked in: [<c0281f30>] (unwind_backtrace+0x0/0xf0) from [<c029341c>] (warn_slowpath_common+0x4c/0x64) [<c029341c>] (warn_slowpath_common+0x4c/0x64) from [<c029344c>] (warn_slowpath_null+0x18/0x1c) [<c029344c>] (warn_slowpath_null+0x18/0x1c) from [<c044b1e4>] (serial_pxa_set_termios+0x1dc/0x250) [<c044b1e4>] (serial_pxa_set_termios+0x1dc/0x250) from [<c044a840>] (uart_resume_port+0x128/0x2dc) [<c044a840>] (uart_resume_port+0x128/0x2dc) from [<c044bbe0>] (serial_pxa_resume+0x18/0x24) [<c044bbe0>] (serial_pxa_resume+0x18/0x24) from [<c0454d34>] (platform_pm_resume+0x40/0x4c) [<c0454d34>] (platform_pm_resume+0x40/0x4c) from [<c0457ebc>] (pm_op+0x68/0xb4) [<c0457ebc>] (pm_op+0x68/0xb4) from [<c0458368>] (device_resume+0xb0/0xec) [<c0458368>] (device_resume+0xb0/0xec) from [<c04584c8>] (dpm_resume+0xe0/0x194) [<c04584c8>] (dpm_resume+0xe0/0x194) from [<c0458588>] (dpm_resume_end+0xc/0x18) [<c0458588>] (dpm_resume_end+0xc/0x18) from [<c02c518c>] (suspend_devices_and_enter+0x16c/0x1ac) [<c02c518c>] (suspend_devices_and_enter+0x16c/0x1ac) from [<c02c5278>] (enter_state+0xac/0xdc) [<c02c5278>] (enter_state+0xac/0xdc) from [<c02c48ec>] (state_store+0xa0/0xbc) [<c02c48ec>] (state_store+0xa0/0xbc) from [<c0408f7c>] (kobj_attr_store+0x18/0x1c) [<c0408f7c>] (kobj_attr_store+0x18/0x1c) from [<c034a6a4>] (sysfs_write_file+0x108/0x140) [<c034a6a4>] (sysfs_write_file+0x108/0x140) from [<c02fb798>] (vfs_write+0xac/0x134) [<c02fb798>] (vfs_write+0xac/0x134) from [<c02fb8cc>] (sys_write+0x3c/0x68) [<c02fb8cc>] (sys_write+0x3c/0x68) from [<c027c700>] (ret_fast_syscall+0x0/0x2c) ---[ end trace 88289eceb4675b04 ]--- This patch fix the problem by adding the power on opertion back for uart console when console_suspend_enabled is true. Signed-off-by:
Ning Jiang <ning.jiang@marvell.com> Tested-by:
Mayank Rana <mrana@codeaurora.org> Signed-off-by:
-
Marcus Folkesson authored
commit e44aabd6 upstream. Errata E20: UART: Character Timeout interrupt remains set under certain software conditions. Implication: The software servicing the UART can be trapped in an infinite loop. Signed-off-by:
Marcus Folkesson <marcus.folkesson@gmail.com> Signed-off-by:
-
Rigbert Hamisch authored
commit 1bfac90d upstream. add device ID for "HP un2430 Mobile Broadband Module" Signed-off-by:
Rigbert Hamisch <rigbert@gmx.de> Signed-off-by:
-
Richard Hartmann authored
commit 68c79e57 upstream. Simple patch to make qcserial recognize the USB id of the Sierra Wireless MC8355 which is based on the Gobi 3000 chip. Both UMTS and GPS work fine. Signed-off-by:
Richard Hartmann <richih.mailinglist@gmail.com> Signed-off-by:
-
Mike Sterling authored
commit cf55f4a8 upstream. If a LUN larger than 2 TB is attached to a Linux VM on Hyper-V, we currently report a maximum size of 2 TB. This patch resolves the issue in hv_storvsc. Thanks to Robert Scheck <robert.scheck@etes.de> for reporting the issue. Reported-by:
Robert Scheck <robert.scheck@etes.de> Signed-off-by:
Mike Sterling <mike.sterling@microsoft.com> Signed-off-by:
K.Y. Srinivasan <kys@microsoft.com> Signed-off-by:
Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by:
-
Kautuk Consul authored
commit e8df1674 upstream. If the usermode app does an ioctl over this serial device by using TIOCMIWAIT, then the code will wait by setting the current task state to TASK_INTERRUPTIBLE and then calling schedule(). This will be woken up by the qt2_process_modem_status on URB completion when the port_extra->shadowMSR is set to the new modem status. However, this could result in a lost wakeup scenario due to a race in the logic in the qt2_ioctl(TIOCMIWAIT) loop and the URB completion for new modem status in qt2_process_modem_status. Due to this, the usermode app's task will continue to sleep despite a change in the modem status. Signed-off-by:
-
