If the kernel is configured with KASAN_EXTRA, the stack size is
increasted significantly because this option sets "-fstack-reuse" to
"none" in GCC [1].  As a result, it triggers stack overrun quite often
with 32k stack size compiled using GCC 8.  For example, this reproducer

  https://github.com/linux-test-project/ltp/blob/master/testcases/kernel/syscalls/madvise/madvise06.c

triggers a "corrupted stack end detected inside scheduler" very reliably
with CONFIG_SCHED_STACK_END_CHECK enabled.

There are just too many functions that could have a large stack with
KASAN_EXTRA due to large local variables that have been called over and
over again without being able to reuse the stacks.  Some noticiable ones
are

  size
  7648 shrink_page_list
  3584 xfs_rmap_convert
  3312 migrate_page_move_mapping
  3312 dev_ethtool
  3200 migrate_misplaced_transhuge_page
  3168 copy_process

There are other 49 functions are over 2k in size while compiling kernel
with "-Wframe-larger-than=" even with a related minimal config on this
machine.  Hence, it is too much work to change Makefiles for each object
to compile without "-fsanitize-address-use-after-scope" individually.

[1] https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81715#c23

Although there is a patch in GCC 9 to help the situation, GCC 9 probably
won't be released in a few months and then it probably take another
6-month to 1-year for all major distros to include it as a default.
Hence, the stack usage with KASAN_EXTRA can be revisited again in 2020
when GCC 9 is everywhere.  Until then, this patch will help users avoid
stack overrun.

This has already been fixed for arm64 for the same reason via
6e883067 ("arm64: kasan: Increase stack size for KASAN_EXTRA").

Link: http://lkml.kernel.org/r/20190109215209.2903-1-cai@lca.pwSigned-off-by: Qian Cai <cai@lca.pw>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hugetlb needs the same fix as faultin_nopage (which was applied in
commit 96312e61 ("mm/gup.c: teach get_user_pages_unlocked to handle
FOLL_NOWAIT")) or KVM hangs because it thinks the mmap_sem was already
released by hugetlb_fault() if it returned VM_FAULT_RETRY, but it wasn't
in the FOLL_NOWAIT case.

Link: http://lkml.kernel.org/r/20190109020203.26669-2-aarcange@redhat.com
Fixes: ce53053c ("kvm: switch get_user_page_nowait() to get_user_pages_unlocked()")
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Tested-by: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Reported-by: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Most architectures do not export shmparam.h to user-space.

  $ find arch -name shmparam.h  | sort
  arch/alpha/include/asm/shmparam.h
  arch/arc/include/asm/shmparam.h
  arch/arm64/include/asm/shmparam.h
  arch/arm/include/asm/shmparam.h
  arch/csky/include/asm/shmparam.h
  arch/ia64/include/asm/shmparam.h
  arch/mips/include/asm/shmparam.h
  arch/nds32/include/asm/shmparam.h
  arch/nios2/include/asm/shmparam.h
  arch/parisc/include/asm/shmparam.h
  arch/powerpc/include/asm/shmparam.h
  arch/s390/include/asm/shmparam.h
  arch/sh/include/asm/shmparam.h
  arch/sparc/include/asm/shmparam.h
  arch/x86/include/asm/shmparam.h
  arch/xtensa/include/asm/shmparam.h

Strangely, some users of the asm-generic wrapper export shmparam.h

  $ git grep 'generic-y += shmparam.h'
  arch/c6x/include/uapi/asm/Kbuild:generic-y += shmparam.h
  arch/h8300/include/uapi/asm/Kbuild:generic-y += shmparam.h
  arch/hexagon/include/uapi/asm/Kbuild:generic-y += shmparam.h
  arch/m68k/include/uapi/asm/Kbuild:generic-y += shmparam.h
  arch/microblaze/include/uapi/asm/Kbuild:generic-y += shmparam.h
  arch/openrisc/include/uapi/asm/Kbuild:generic-y += shmparam.h
  arch/riscv/include/asm/Kbuild:generic-y += shmparam.h
  arch/unicore32/include/uapi/asm/Kbuild:generic-y += shmparam.h

The newly added riscv correctly creates the asm-generic wrapper
in the kernel space, but the others (c6x, h8300, hexagon, m68k,
microblaze, openrisc, unicore32) create the one in the uapi directory.

Digging into the git history, now I guess fcc8487d ("uapi:
export all headers under uapi directories") was the misconversion.
Prior to that commit, no architecture exported to shmparam.h
As its commit description said, that commit exported shmparam.h
for c6x, h8300, hexagon, m68k, openrisc, unicore32.

83f0124a ("microblaze: remove asm-generic wrapper headers")
accidentally exported shmparam.h for microblaze.

This commit unexports shmparam.h for those architectures.

There is no more reason to export include/uapi/asm-generic/shmparam.h,
so it has been moved to include/asm-generic/shmparam.h

Link: http://lkml.kernel.org/r/1546904307-11124-1-git-send-email-yamada.masahiro@socionext.comSigned-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stafford Horne <shorne@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Aurelien Jacquiot <jacquiot.aurelien@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Guo Ren <guoren@kernel.org>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: Mark Salter <msalter@redhat.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Vincent Chen <deanbo422@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

/proc entries under /proc/net/* can't be cached into dcache because
setns(2) can change current net namespace.

[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: avoid vim miscolorization]
[adobriyan@gmail.com: write test, add dummy ->d_revalidate hook: necessary if /proc/net/* is pinned at setns time]
  Link: http://lkml.kernel.org/r/20190108192350.GA12034@avx2
Link: http://lkml.kernel.org/r/20190107162336.GA9239@avx2
Fixes: 1da4d377 ("proc: revalidate misc dentries")
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Reported-by: Mateusz Stępień <mateusz.stepien@netrounds.com>
Reported-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

do_migrate_range() takes a memory range and tries to isolate the pages
to put them into a list.  This list will be later on used in
migrate_pages() to know the pages we need to migrate.

Currently, if we fail to isolate a single page, we put all already
isolated pages back to their LRU and we bail out from the function.
This is quite suboptimal, as this will force us to start over again
because scan_movable_pages will give us the same range.  If there is no
chance that we can isolate that page, we will loop here forever.

Issue debugged in [1] has proved that.  During the debugging of that
issue, it was noticed that if do_migrate_ranges() fails to isolate a
single page, we will just discard the work we have done so far and bail
out, which means that scan_movable_pages() will find again the same set
of pages.

Instead, we can just skip the error, keep isolating as much pages as
possible and then proceed with the call to migrate_pages().

This will allow us to do as much work as possible at once.

[1] https://lkml.org/lkml/2018/12/6/324

Michal said:

: I still think that this doesn't give us a whole picture.  Looping for
: ever is a bug.  Failing the isolation is quite possible and it should
: be a ephemeral condition (e.g.  a race with freeing the page or
: somebody else isolating the page for whatever reason).  And here comes
: the disadvantage of the current implementation.  We simply throw
: everything on the floor just because of a ephemeral condition.  The
: racy page_count check is quite dubious to prevent from that.

Link: http://lkml.kernel.org/r/20181211135312.27034-1-osalvador@suse.deSigned-off-by: Oscar Salvador <osalvador@suse.de>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Dan Williams <dan.j.williams@gmail.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: William Kucharski <william.kucharski@oracle.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull rdma fixes from Jason Gunthorpe:
 "Still not much going on, the usual set of oops and driver fixes this
  time:

   - Fix two uapi breakage regressions in mlx5 drivers

   - Various oops fixes in hfi1, mlx4, umem, uverbs, and ipoib

   - A protocol bug fix for hfi1 preventing it from implementing the
     verbs API properly, and a compatability fix for EXEC STACK user
     programs

   - Fix missed refcounting in the 'advise_mr' patches merged this
     cycle.

   - Fix wrong use of the uABI in the hns SRQ patches merged this cycle"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
  IB/uverbs: Fix OOPs in uverbs_user_mmap_disassociate
  IB/ipoib: Fix for use-after-free in ipoib_cm_tx_start
  IB/uverbs: Fix ioctl query port to consider device disassociation
  RDMA/mlx5: Fix flow creation on representors
  IB/uverbs: Fix OOPs upon device disassociation
  RDMA/umem: Add missing initialization of owning_mm
  RDMA/hns: Update the kernel header file of hns
  IB/mlx5: Fix how advise_mr() launches async work
  RDMA/device: Expose ib_device_try_get(()
  IB/hfi1: Add limit test for RC/UC send via loopback
  IB/hfi1: Remove overly conservative VM_EXEC flag check
  IB/{hfi1, qib}: Fix WC.byte_len calculation for UD_SEND_WITH_IMM
  IB/mlx4: Fix using wrong function to destroy sqp AHs under SRIOV
  RDMA/mlx5: Fix check for supported user flags when creating a QP

Pull iomap fixes from Darrick Wong:
 "A couple of iomap fixes to eliminate some memory corruption and hang
  problems that were reported:

   - fix page migration when using iomap for pagecache management

   - fix a use-after-free bug in the directio code"

* tag 'iomap-5.0-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  iomap: fix a use after free in iomap_dio_rw
  iomap: get/put the page in iomap_page_create/release()

Pull power management fixes from Rafael Wysocki:
 "These fix a PM-runtime framework regression introduced by the recent
  switch-over of device autosuspend to hrtimers and a mistake in the
  "poll idle state" code introduced by a recent change in it.

  Specifics:

   - Since ktime_get() turns out to be problematic for device
     autosuspend in the PM-runtime framework, make it use
     ktime_get_mono_fast_ns() instead (Vincent Guittot).

   - Fix an initial value of a local variable in the "poll idle state"
     code that makes it behave not exactly as expected when all idle
     states except for the "polling" one are disabled (Doug Smythies)"

* tag 'pm-5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpuidle: poll_state: Fix default time limit
  PM-runtime: Fix deadlock with ktime_get()

Pull ACPI Kconfig fixes from Rafael Wysocki:
 "Prevent invalid configurations from being created (e.g. by randconfig)
  due to some ACPI-related Kconfig options' dependencies that are not
  specified directly (Sinan Kaya)"

* tag 'acpi-5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  platform/x86: Fix unmet dependency warning for SAMSUNG_Q10
  platform/x86: Fix unmet dependency warning for ACPI_CMPC
  mfd: Fix unmet dependency warning for MFD_TPS68470

Pull MMC host fixes from Ulf Hansson:

 - mediatek: Fix incorrect register write for tunings

 - bcm2835: Fixup leakage of DMA channel on probe errors

* tag 'mmc-v5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: mediatek: fix incorrect register setting of hs400_cmd_int_delay
  mmc: bcm2835: Fix DMA channel leak on probe error

Pull i3c fixes from Boris Brezillon:

 - Fix a deadlock in the designware driver

 - Fix the error path in i3c_master_add_i3c_dev_locked()

* tag 'i3c/fixes-for-5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
  i3c: master: dw: fix deadlock
  i3c: fix missing detach if failed to retrieve i3c dev

In commit 170d13ca ("x86: re-introduce non-generic memcpy_{to,from}io")
I made our copy from IO space use a separate copy routine rather than
rely on the generic memcpy.  I did that because our generic memory copy
isn't actually well-defined when it comes to internal access ordering or
alignment, and will in fact depend on various CPUID flags.

In particular, the default memcpy() for a modern Intel CPU will
generally be just a "rep movsb", which works reasonably well for
medium-sized memory copies of regular RAM, since the CPU will turn it
into fairly optimized microcode.

However, for non-cached memory and IO, "rep movs" ends up being
horrendously slow and will just do the architectural "one byte at a
time" accesses implied by the movsb.

At the other end of the spectrum, if you _don't_ end up using the "rep
movsb" code, you'd likely fall back to the software copy, which does
overlapping accesses for the tail, and may copy things backwards.
Again, for regular memory that's fine, for IO memory not so much.

The thinking was that clearly nobody really cared (because things
worked), but some people had seen horrible performance due to the byte
accesses, so let's just revert back to our long ago version that dod
"rep movsl" for the bulk of the copy, and then fixed up the potentially
last few bytes of the tail with "movsw/b".

Interestingly (and perhaps not entirely surprisingly), while that was
our original memory copy implementation, and had been used before for
IO, in the meantime many new users of memcpy_*io() had come about.  And
while the access patterns for the memory copy weren't well-defined (so
arguably _any_ access pattern should work), in practice the "rep movsb"
case had been very common for the last several years.

In particular Jarkko Sakkinen reported that the memcpy_*io() change
resuled in weird errors from his Geminilake NUC TPM module.

And it turns out that the TPM TCG accesses according to spec require
that the accesses be

 (a) done strictly sequentially

 (b) be naturally aligned

otherwise the TPM chip will abort the PCI transaction.

And, in fact, the tpm_crb.c driver did this:

	memcpy_fromio(buf, priv->rsp, 6);
	...
	memcpy_fromio(&buf[6], &priv->rsp[6], expected - 6);

which really should never have worked in the first place, but back
before commit 170d13ca it *happened* to work, because the
memcpy_fromio() would be expanded to a regular memcpy, and

 (a) gcc would expand the first memcpy in-line, and turn it into a
     4-byte and a 2-byte read, and they happened to be in the right
     order, and the alignment was right.

 (b) gcc would call "memcpy()" for the second one, and the machines that
     had this TPM chip also apparently ended up always having ERMS
     ("Enhanced REP MOVSB/STOSB instructions"), so we'd use the "rep
     movbs" for that copy.

In other words, basically by pure luck, the code happened to use the
right access sizes in the (two different!) memcpy() implementations to
make it all work.

But after commit 170d13ca, both of the memcpy_fromio() calls
resulted in a call to the routine with the consistent memory accesses,
and in both cases it started out transferring with 4-byte accesses.
Which worked for the first copy, but resulted in the second copy doing a
32-bit read at an address that was only 2-byte aligned.

Jarkko is actually fixing the fragile code in the TPM driver, but since
this is an excellent example of why we absolutely must not use a generic
memcpy for IO accesses, _and_ an IO-specific one really should strive to
align the IO accesses, let's do exactly that.

Side note: Jarkko also noted that the driver had been used on ARM
platforms, and had worked.  That was because on 32-bit ARM, memcpy_*io()
ends up always doing byte accesses, and on 64-bit ARM it first does byte
accesses to align to 8-byte boundaries, and then does 8-byte accesses
for the bulk.

So ARM actually worked by design, and the x86 case worked by pure luck.

We *might* want to make x86-64 do the 8-byte case too.  That should be a
pretty straightforward extension, but let's do one thing at a time.  And
generally MMIO accesses aren't really all that performance-critical, as
shown by the fact that for a long time we just did them a byte at a
time, and very few people ever noticed.
Reported-and-tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jerry Snitselaar <jsnitsel@redhat.com>
Cc: David Laight <David.Laight@aculab.com>
Fixes: 170d13ca ("x86: re-introduce non-generic memcpy_{to,from}io")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* acpi-misc:
  platform/x86: Fix unmet dependency warning for SAMSUNG_Q10
  platform/x86: Fix unmet dependency warning for ACPI_CMPC

* pm-cpuidle-fixes:
  cpuidle: poll_state: Fix default time limit

Pull clk fixes from Stephen Boyd:
 "Mostly driver fixes, but there's a core framework fix in here too:

   - Revert the commits that introduce clk management for the SP clk on
     MMP2 SoCs (used for OLPC). Turns out it wasn't a good idea and
     there isn't any need to manage this clk, it just causes more
     headaches.

   - A performance regression that went unnoticed for many years where
     we would traverse the entire clk tree looking for a clk by name
     when we already have the pointer to said clk that we're looking for

   - A parent linkage fix for the qcom SDM845 clk driver

   - An i.MX clk driver rate miscalculation fix where order of
     operations were messed up

   - One error handling fix from the static checkers"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: qcom: gcc: Use active only source for CPUSS clocks
  clk: ti: Fix error handling in ti_clk_parse_divider_data()
  clk: imx: Fix fractional clock set rate computation
  clk: Remove global clk traversal on fetch parent index
  Revert "dt-bindings: marvell,mmp2: Add clock id for the SP clock"
  Revert "clk: mmp2: add SP clock"
  Revert "Input: olpc_apsp - enable the SP clock"

Pull crypto fix from Herbert Xu:
 "This fixes a bug in cavium/nitrox where the callback is invoked prior
  to the DMA unmap"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: cavium/nitrox - Invoke callback after DMA unmap

Pull PCI fixes from Bjorn Helgaas:

 - Revert armada8k GPIO reset change that broke Macchiatobin booting
   (Baruch Siach)

 - Use actual size config reads on ARM cns3xxx (Koen Vandeputte)

 - Fix ARM cns3xxx config write alignment issue (Koen Vandeputte)

 - Fix imx6 PHY device link error checking (Leonard Crestez)

 - Fix imx6 probe failure on chips without separate PCI power domain
   (Leonard Crestez)

* tag 'pci-v5.0-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  Revert "PCI: armada8k: Add support for gpio controlled reset signal"
  ARM: cns3xxx: Use actual size reads for PCIe
  ARM: cns3xxx: Fix writing to wrong PCI config registers after alignment
  PCI: imx: Fix checking pd_pcie_phy device link addition
  PCI: imx: Fix probe failure without power domain

Revert commit 3d71746c ("PCI: armada8k: Add support for gpio controlled
reset signal").

That commit breaks boot on Macchiatobin board when a Mellanox NIC is
present in the PCIe slot.

It turns out that full reset cycle requires first comphy serdes
initialization. Reset signal toggle without comphy initialization makes
access to PCI configuration registers stall indefinitely. U-Boot toggles
the Macchiatobin PCIe reset line already at boot, after initializing the
comphy serdes.

So while commit 3d71746c ("PCI: armada8k: Add support for gpio controlled
reset signal") enables PCIe on platforms that U-Boot does not touch the
reset line (like Clearfog GT-8K), it breaks PCIe (and boot) on the
Macchiatobin board.

Revert commit 3d71746c ("PCI: armada8k: Add support for gpio controlled
reset signal") entirely to fix the Macchiatobin regression.
Reported-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

commit 802b7c06 ("ARM: cns3xxx: Convert PCI to use generic config
accessors") reimplemented cns3xxx_pci_read_config() using
pci_generic_config_read32(), which preserved the property of only doing
32-bit reads.

It also replaced cns3xxx_pci_write_config() with pci_generic_config_write(),
so it changed writes from always being 32 bits to being the actual size,
which works just fine.

Given that:

- The documentation does not mention that only 32 bit access is allowed.
- Writes are already executed using the actual size
- Extensive testing shows that 8b, 16b and 32b reads work as intended

Allow read access of any size by replacing pci_generic_config_read32()
with the pci_generic_config_read() accessors.

Fixes: 802b7c06 ("ARM: cns3xxx: Convert PCI to use generic config accessors")
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
Acked-by: Arnd Bergmann <arnd@arndb.de>
CC: Krzysztof Halasa <khalasa@piap.pl>
CC: Olof Johansson <olof@lixom.net>
CC: Robin Leblon <robin.leblon@ncentric.com>
CC: Rob Herring <robh@kernel.org>
CC: Russell King <linux@armlinux.org.uk>
CC: Tim Harvey <tharvey@gateworks.com>

Originally, cns3xxx used its own functions for mapping, reading and
writing config registers.

Commit 802b7c06 ("ARM: cns3xxx: Convert PCI to use generic config
accessors") removed the internal PCI config write function in favor of
the generic one:

  cns3xxx_pci_write_config() --> pci_generic_config_write()

cns3xxx_pci_write_config() expected aligned addresses, being produced by
cns3xxx_pci_map_bus() while the generic one pci_generic_config_write()
actually expects the real address as both the function and hardware are
capable of byte-aligned writes.

This currently leads to pci_generic_config_write() writing to the wrong
registers.

For instance, upon ath9k module loading:

- driver ath9k gets loaded
- The driver wants to write value 0xA8 to register PCI_LATENCY_TIMER,
  located at 0x0D
- cns3xxx_pci_map_bus() aligns the address to 0x0C
- pci_generic_config_write() effectively writes 0xA8 into register 0x0C
  (CACHE_LINE_SIZE)

Fix the bug by removing the alignment in the cns3xxx mapping function.

Fixes: 802b7c06 ("ARM: cns3xxx: Convert PCI to use generic config accessors")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
CC: stable@vger.kernel.org	# v4.0+
CC: Bjorn Helgaas <bhelgaas@google.com>
CC: Olof Johansson <olof@lixom.net>
CC: Robin Leblon <robin.leblon@ncentric.com>
CC: Rob Herring <robh@kernel.org>
CC: Russell King <linux@armlinux.org.uk>

The check on the device_link_add() return value is wrong;
this leads to erroneous code execution, so fix it.

Fixes: 3f7cceea ("PCI: imx: Add multi-pd support")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

On chips without a separate power domain for PCI (such as 6q/6qp) the
imx6_pcie_attach_pd() function incorrectly returns an error.

Fix by returning 0 if dev_pm_domain_attach_by_name() does not find
anything.

Fixes: 3f7cceea ("PCI: imx: Add multi-pd support")
Reported-by: Lukas F.Hartmann <lukas@mntmn.com>
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

This reverts commit 2d29f6b9.

It turns out that the fix can lead to a ~20 percent performance regression
in initial writes to the page cache according to iozone.  Let's revert this
for now to have more time for a proper fix.

Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'linux-kselftest-5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull kselftest fixes from Shuah Khan:
 "This consists of run-time fixes to cpu-hotplug, and seccomp tests,
  compile fixes to ir, net, and timers Makefiles"

* tag 'linux-kselftest-5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  selftests: timers: use LDLIBS instead of LDFLAGS
  selftests: net: use LDLIBS instead of LDFLAGS
  selftests/seccomp: Enhance per-arch ptrace syscall skip tests
  selftests: Use lirc.h from kernel tree, not from system
  selftests: cpu-hotplug: fix case where CPUs offline > CPUs present

Pull NFS client fixes from Anna Schumaker:
 "This addresses two bugs, one in the error code handling of
  nfs_page_async_flush() and one to fix a potential NULL pointer
  dereference in nfs_parse_devname().

  Stable bugfix:
   - Fix up return value on fatal errors in nfs_page_async_flush()

  Other bugfix:
   - Fix NULL pointer dereference of dev_name"

* tag 'nfs-for-5.0-3' of git://git.linux-nfs.org/projects/anna/linux-nfs:
  NFS: Fix up return value on fatal errors in nfs_page_async_flush()
  nfs: Fix NULL pointer dereference of dev_name

Pull sound fixes from Takashi Iwai:
 "Only three fixes.

  The fix for Realtek HD-audio looks lengthy, but it's just a code
  shuffling, and the actual changes are fairly small.

  The rest are a PCM core fix for a long-standing bug that was recently
  scratched by syzkaller, and a trivial USB-audio quirk for DSD support"

* tag 'sound-5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda/realtek - Fixed hp_pin no value
  ALSA: pcm: Fix tight loop of OSS capture stream
  ALSA: usb-audio: Add Opus #3 to quirks for native DSD support

The default time is declared in units of microsecnds,
but is used as nanoseconds, resulting in significant
accounting errors for idle state 0 time when all idle
states deeper than 0 are disabled.

Under these unusual conditions, we don't really care
about the poll time limit anyhow.

Fixes: 800fb34a ("cpuidle: poll_state: Disregard disable idle states")
Signed-off-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

A deadlock has been seen when swicthing clocksources which use
PM-runtime.  The call path is:

change_clocksource
    ...
    write_seqcount_begin
    ...
    timekeeping_update
        ...
        sh_cmt_clocksource_enable
            ...
            rpm_resume
                pm_runtime_mark_last_busy
                    ktime_get
                        do
                            read_seqcount_begin
                        while read_seqcount_retry
    ....
    write_seqcount_end

Although we should be safe because we haven't yet changed the
clocksource at that time, we can't do that because of seqcount
protection.

Use ktime_get_mono_fast_ns() instead which is lock safe for such
cases.

With ktime_get_mono_fast_ns, the timestamp is not guaranteed to be
monotonic across an update and as a result can goes backward.
According to update_fast_timekeeper() description: "In the worst
case, this can result is a slightly wrong timestamp (a few
nanoseconds)". For PM-runtime autosuspend, this means only that
the suspend decision may be slightly suboptimal.

Fixes: 8234f673 ("PM-runtime: Switch autosuspend over to using hrtimers")
Reported-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

The current dentry number tracking code doesn't distinguish between
positive & negative dentries.  It just reports the total number of
dentries in the LRU lists.

As excessive number of negative dentries can have an impact on system
performance, it will be wise to track the number of positive and
negative dentries separately.

This patch adds tracking for the total number of negative dentries in
the system LRU lists and reports it in the 5th field in the
/proc/sys/fs/dentry-state file.  The number, however, does not include
negative dentries that are in flight but not in the LRU yet as well as
those in the shrinker lists which are on the way out anyway.

The number of positive dentries in the LRU lists can be roughly found by
subtracting the number of negative dentries from the unused count.

Matthew Wilcox had confirmed that since the introduction of the
dentry_stat structure in 2.1.60, the dummy array was there, probably for
future extension.  They were not replacements of pre-existing fields.
So no sane applications that read the value of /proc/sys/fs/dentry-state
will do dummy thing if the last 2 fields of the sysctl parameter are not
zero.  IOW, it will be safe to use one of the dummy array entry for
negative dentry count.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The list_lru structure is essentially just a pointer to a table of
per-node LRU lists.  Even if CONFIG_MEMCG_KMEM is defined, the list
field is just used for LRU list registration and shrinker_id is set at
initialization.  Those fields won't need to be touched that often.

So there is no point to make the list_lru structures to sit in their own
cachelines.
Signed-off-by: Waiman Long <longman@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The nr_dentry_unused per-cpu counter tracks dentries in both the LRU
lists and the shrink lists where the DCACHE_LRU_LIST bit is set.

The shrink_dcache_sb() function moves dentries from the LRU list to a
shrink list and subtracts the dentry count from nr_dentry_unused.  This
is incorrect as the nr_dentry_unused count will also be decremented in
shrink_dentry_list() via d_shrink_del().

To fix this double decrement, the decrement in the shrink_dcache_sb()
function is taken out.

Fixes: 4e717f5c ("list_lru: remove special case function list_lru_dispose_all."
Cc: stable@kernel.org
Signed-off-by: Waiman Long <longman@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull IOMMU fixes from Joerg Roedel:
 "A few more fixes this time:

   - Two patches to fix the error path of the map_sg implementation of
     the AMD IOMMU driver.

   - Also a missing IOTLB flush is fixed in the AMD IOMMU driver.

   - Memory leak fix for the Intel IOMMU driver.

   - Fix a regression in the Mediatek IOMMU driver which caused device
     initialization to fail (seen as broken HDMI output)"

* tag 'iommu-fixes-v5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/amd: Fix IOMMU page flush when detach device from a domain
  iommu/mediatek: Use correct fwspec in mtk_iommu_add_device()
  iommu/vt-d: Fix memory leak in intel_iommu_put_resv_regions()
  iommu/amd: Unmap all mapped pages in error path of map_sg
  iommu/amd: Call free_iova_fast with pfn in map_sg

Pull GPIO fixes from Linus Walleij:
 "Here is a bunch of GPIO fixes for the v5.0 series. I was helped out by
  Bartosz in collecting these fixes, for which I am very grateful, the
  biggest achievement in GPIO right now is work distribution.

  There is one serious core fix (timestamping) and a bunch of driver
  fixes:

   - Fix timestamps on nested IRQs

   - Handle IRQs properly in multiple instances of PCF857x

   - Use the right data register and IRQ type setting in the Spreadtrum
     GPIO driver

   - Let the value argument work properly when setting direction in the
     Altera GPIO driver

   - Mask interrupts properly in the vf610 driver"

* tag 'gpio-v5.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: vf610: Mask all GPIO interrupts
  gpio: altera-a10sr: Set proper output level for direction_output
  gpio: sprd: Fix incorrect irq type setting for the async EIC
  gpio: sprd: Fix the incorrect data register
  gpiolib: fix line event timestamps for nested irqs
  gpio: pcf857x: Fix interrupts on multiple instances

Pull networking fixes from David Miller:

 1) Need to save away the IV across tls async operations, from Dave
    Watson.

 2) Upon successful packet processing, we should liberate the SKB with
    dev_consume_skb{_irq}(). From Yang Wei.

 3) Only apply RX hang workaround on effected macb chips, from Harini
    Katakam.

 4) Dummy netdev need a proper namespace assigned to them, from Josh
    Elsasser.

 5) Some paths of nft_compat run lockless now, and thus we need to use a
    proper refcnt_t. From Florian Westphal.

 6) Avoid deadlock in mlx5 by doing IRQ locking, from Moni Shoua.

 7) netrom does not refcount sockets properly wrt. timers, fix that by
    using the sock timer API. From Cong Wang.

 8) Fix locking of inexact inserts of xfrm policies, from Florian
    Westphal.

 9) Missing xfrm hash generation bump, also from Florian.

10) Missing of_node_put() in hns driver, from Yonglong Liu.

11) Fix DN_IFREQ_SIZE, from Johannes Berg.

12) ip6mr notifier is invoked during traversal of wrong table, from Nir
    Dotan.

13) TX promisc settings not performed correctly in qed, from Manish
    Chopra.

14) Fix OOB access in vhost, from Jason Wang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
  MAINTAINERS: Add entry for XDP (eXpress Data Path)
  net: set default network namespace in init_dummy_netdev()
  net: b44: replace dev_kfree_skb_xxx by dev_consume_skb_xxx for drop profiles
  net: caif: call dev_consume_skb_any when skb xmit done
  net: 8139cp: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
  net: macb: Apply RXUBR workaround only to versions with errata
  net: ti: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
  net: apple: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
  net: amd8111e: replace dev_kfree_skb_irq by dev_consume_skb_irq
  net: alteon: replace dev_kfree_skb_irq by dev_consume_skb_irq
  net: tls: Fix deadlock in free_resources tx
  net: tls: Save iv in tls_rec for async crypto requests
  vhost: fix OOB in get_rx_bufs()
  qed: Fix stack out of bounds bug
  qed: Fix system crash in ll2 xmit
  qed: Fix VF probe failure while FLR
  qed: Fix LACP pdu drops for VFs
  qed: Fix bug in tx promiscuous mode settings
  net: i825xx: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
  netfilter: ipt_CLUSTERIP: fix warning unused variable cn
  ...

Ensure that we return the fatal error value that caused us to exit
nfs_page_async_flush().

Fixes: c373fff7 ("NFSv4: Don't special case "launder"")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: stable@vger.kernel.org # v4.12+
Reviewed-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>

The vma->vm_mm can become impossible to get before rdma_umap_close() is
called, in this case we must not try to get an mm that is already
undergoing process exit. In this case there is no need to wait for
anything as the VMA will be destroyed by another thread soon and is
already effectively 'unreachable' by userspace.

 BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
 PGD 800000012bc50067 P4D 800000012bc50067 PUD 129db5067 PMD 0
 Oops: 0000 [#1] SMP PTI
 CPU: 1 PID: 2050 Comm: bash Tainted: G        W  OE 4.20.0-rc6+ #3
 Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
 RIP: 0010:__rb_erase_color+0xb9/0x280
 Code: 84 17 01 00 00 48 3b 68 10 0f 84 15 01 00 00 48 89
               58 08 48 89 de 48 89 ef 4c 89 e3 e8 90 84 22 00 e9 60 ff ff ff 48 8b 5d
               10 <f6> 03 01 0f 84 9c 00 00 00 48 8b 43 10 48 85 c0 74 09 f6 00 01 0f
 RSP: 0018:ffffbecfc090bab8 EFLAGS: 00010246
 RAX: ffff97616346cf30 RBX: 0000000000000000 RCX: 0000000000000101
 RDX: 0000000000000000 RSI: ffff97623b6ca828 RDI: ffff97621ef10828
 RBP: ffff97621ef10828 R08: ffff97621ef10828 R09: 0000000000000000
 R10: 0000000000000000 R11: 0000000000000000 R12: ffff97623b6ca838
 R13: ffffffffbb3fef50 R14: ffff97623b6ca828 R15: 0000000000000000
 FS:  00007f7a5c31d740(0000) GS:ffff97623bb00000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 0000000000000000 CR3: 000000011255a000 CR4: 00000000000006e0
 Call Trace:
  unlink_file_vma+0x3b/0x50
  free_pgtables+0xa1/0x110
  exit_mmap+0xca/0x1a0
  ? mlx5_ib_dealloc_pd+0x28/0x30 [mlx5_ib]
  mmput+0x54/0x140
  uverbs_user_mmap_disassociate+0xcc/0x160 [ib_uverbs]
  uverbs_destroy_ufile_hw+0xf7/0x120 [ib_uverbs]
  ib_uverbs_remove_one+0xea/0x240 [ib_uverbs]
  ib_unregister_device+0xfb/0x200 [ib_core]
  mlx5_ib_remove+0x51/0xe0 [mlx5_ib]
  mlx5_remove_device+0xc1/0xd0 [mlx5_core]
  mlx5_unregister_device+0x3d/0xb0 [mlx5_core]
  remove_one+0x2a/0x90 [mlx5_core]
  pci_device_remove+0x3b/0xc0
  device_release_driver_internal+0x16d/0x240
  unbind_store+0xb2/0x100
  kernfs_fop_write+0x102/0x180
  __vfs_write+0x36/0x1a0
  ? __alloc_fd+0xa9/0x170
  ? set_close_on_exec+0x49/0x70
  vfs_write+0xad/0x1a0
  ksys_write+0x52/0xc0
  do_syscall_64+0x5b/0x180
  entry_SYSCALL_64_after_hwframe+0x44/0xa9

Cc: <stable@vger.kernel.org> # 4.19
Fixes: 5f9794dc ("RDMA/ucontext: Add a core API for mmaping driver IO memory")
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>

Add multiple people as maintainers for XDP, sorted alphabetically.

XDP is also tied to driver level support and code, but we cannot add all
drivers to the list. Instead K: and N: match on 'xdp' in hope to catch some
of those changes in drivers.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Assign a default net namespace to netdevs created by init_dummy_netdev().
Fixes a NULL pointer dereference caused by busy-polling a socket bound to
an iwlwifi wireless device, which bumps the per-net BUSYPOLLRXPACKETS stat
if napi_poll() received packets:

  BUG: unable to handle kernel NULL pointer dereference at 0000000000000190
  IP: napi_busy_loop+0xd6/0x200
  Call Trace:
    sock_poll+0x5e/0x80
    do_sys_poll+0x324/0x5a0
    SyS_poll+0x6c/0xf0
    do_syscall_64+0x6b/0x1f0
    entry_SYSCALL_64_after_hwframe+0x3d/0xa2

Fixes: 7db6b048 ("net: Commonize busy polling code to focus on napi_id instead of socket")
Signed-off-by: Josh Elsasser <jelsasser@appneta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The skb should be freed by dev_consume_skb_any() in b44_start_xmit()
when bounce_skb is used. The skb is be replaced by bounce_skb, so the
original skb should be consumed(not drop).

dev_consume_skb_irq() should be called in b44_tx() when skb xmit
done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

The skb shouled be consumed when xmit done, it makes drop profiles
(dropwatch, perf) more friendly.
dev_kfree_skb_irq()/kfree_skb() shouled be replaced by
dev_consume_skb_any(), it makes code cleaner.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>