- 03 Sep, 2014 40 commits
-
-
Andy Shevchenko authored
There is no need to use hex_dump_to_buffer() since we have a kernel helper to dump up to 64 bytes just via printk(). In our case the actual size is 15 bytes. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by:
Jani Nikula <jani.nikula@intel.com> [danvet: Add cast since %*ph expects and int for the size parameter.] Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch>
-
Ville Syrjälä authored
WaGsvRC0ResidenncyMethod is for vlv, it doesn't deal with chv appropriately (eg. doesn't limit rps values to even numbers). Fix a typo in the w/a name while at it. Cc: Deepak S <deepak.s@linux.intel.com> Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
Deepak S <deepak.s@linux.intel.com> Signed-off-by:
-
Ville Syrjälä authored
My Fujistsu-Siemens Lifebook S6010 doesn't like to resume from S3 unless VGACNTR has been restore to the original value. The BIOS value in this case was 0x0124008E. Setting the "VGA disable" bit doesn't interfere with the S3 resume fortunately. Signed-off-by:
Thomas Richter <richter@rus.uni-stuttgart.de> Signed-off-by:
-
Ville Syrjälä authored
830M has problems when some of the pipes are disabled. Namely if a plane, DVO port etc. is currently assigned to a disabled pipe, it can't moved to the other pipe until the current pipe is also enabled. To keep things simple just leave both pipes running all the time. Ideally I think should turn the pipes off if neither is active, and when either becomes active we enable both. But that would reuquire proper atomic modeset support, and probably a bit of extra care in the order things get enabled. v2: Reorder wrt. double wide handling changes Signed-off-by:
-
Ville Syrjälä authored
830 really does want the pipe A quirk. The planes and ports don't react to any register writes unless the pipe currently attached to them is running, so it's impossible to move them to the other pipe unless both pipes are running. Also it's documented that the DPLL must be enabled on both pipes whenever it's needed. This reverts commit ac6696d3236bd61503f89a1a99680fd7894d5d53. Signed-off-by:
-
Ville Syrjälä authored
The vbt on my Fujitsu-Siemens Lifebook S6010 provides two 800x600 modes, 60Hz and 56Hz. The magic register values we have correspond to the 60Hz mode, and as I don't know how one would trick the VGA BIOS to set up the 56Hz mode we can't get the magic values for the orther mode. So when checking whether a mode is valid also check the pixel clock so that we filter out the 56Hz variant. Signed-off-by:
-
Ville Syrjälä authored
In my earlier rewrite I missed a few important registers. Thomas Richter noticed that they're needed to make his machine resume correctly. Looks like IEGD does a one time init of these three registers. We don't have a good one time init place in the ns2501 driver, so let's just stick them into the .mode_set() hook and see if that helps things along. Signed-off-by:
-
Ville Syrjälä authored
Try to use the same programming sequence as used by the IEGD driver. Also shovel the magic register values into a big static const array. The register values are actually the based on what the BIOS programs on the Fujitsu-Siemens Lifebook S6010. IEGD seemed to have hardcoded register values (which also enabled the scaler for 1024x768 mode). However those didn't actually work so well on the S6010. Possibly the pipe timings that got used didn't match the ns2501 configuration. Signed-off-by:
-
Ville Syrjälä authored
Signed-off-by:
-
Ville Syrjälä authored
Calling the mode_set hook on DPMS changes doesn't seem to be necessary for ns2501. Just drop it. Signed-off-by:
-
Ville Syrjälä authored
To more closely match the IEGD ns2501 driver behaviour, call the mode_set hook while the DVO port is still disabled, then enable the DVO port, and finally call the dpms hook. Signed-off-by:
-
Ville Syrjälä authored
On Fujitsu-Siememens S6010 the ns2501 chip is hooked up to DVOB instead of DVOC. FIXME: Maybe need to dig out the correct DVO port from VBT Signed-off-by:
-
Ville Syrjälä authored
Disable double wide even if the pipe quirk compels us to leave the pipe running. Double wide has certain implications for the plane assignments so best keep it off. Also helps resuming from S3 on the Fujitsu-Siemens Lifebook S6010 when double wide was enabled prior to suspend. We do leave the pixel clock ticking at the original rate which would require double wide to be enabled. But since the planes are all disabled I'm hoping that the overly fast clock won't cause any problems. Seems to be fine so far. v2: Disable double wide also when turning the pipe off v3: Reorder wrt. force pipe B quirk Signed-off-by:
-
Ville Syrjälä authored
Just pass the intel_crtc around instead of dev_priv+pipe. Also make intel_wait_for_pipe_off() static since it's only used in intel_display.c. Signed-off-by:
-
Ville Syrjälä authored
gen2/3 platforms have a boatload of rings we're not using. On my 830 the BIOS/hw can leave some of those "active" after resume which will prevent c3 entry. The ring is apparently considered active whenever head != tail even if the ring is disabled. Disable and clear all such unused ringbuffers on init/resume. Signed-off-by:
-
Ville Syrjälä authored
My 830 is unhappy with trickle feed enabled. The symptom is that the image on the screen shifts a bit to right occasionally. The BIOS initially disables trickle feed, but it gets reset during suspend, so we need to re-disable it ourselves. Juse disable it always. Also disable it for all other gen2/3 platforms since we disable it for all more recent platforms as well (until HSW that is). At least my 855 doesn't seem to mind us doing this. I don't have gen3 hardware to test that. Signed-off-by:
-
Ville Syrjälä authored
The max watermark value for gen2 planes B and C is 0x1f, instead of the 0x3f that plane A uses. Also check against the max even if the pipe is disabled since the FIFO size exceeds the plane B and C max watermark value. Signed-off-by:
-
Jesse Barnes authored
This gets us out of our init code and out to userspace quite a bit faster, but does open us up to some bugs given the state of our init time locking. v2: switch to async_schedule (Chris) check with lockdep, seems happy (Jesse) move hotplug enable flag set to fbdev_initial_config (Jesse) Signed-off-by:Jesse Barnes <jbarnes@virtuousgeek.org> Reviewed-by:
Chris Wilson <chris@chris-wilson.co.uk> [danvet: Rebase on top of the dev_priv->enable_hotplug_processing removal.] Signed-off-by:
-
Ville Syrjälä authored
Follow the BDW example and apply the workarounds touching registers which are saved in the context image through LRIs in the new ring->init_context() hook. This makes Mesa much happier and eg. glxgears doesn't hang after the first frame. Cc: Arun Siluvery <arun.siluvery@linux.intel.com> Signed-off-by:
"Barbalho, Rafael" <rafael.barbalho@intel.com> Signed-off-by:
-
Gustavo Padovan authored
At this point of the code the obj var is already NULL, so we don't need to set it again to NULL. Signed-off-by:
Gustavo Padovan <gustavo.padovan@collabora.co.uk> Reviewed-by:
-
Ville Syrjälä authored
CHV wants even rps opcodes so print a warning of the min/max/rpe/rp1 values are odd, and warn if an odd value slips through to valleyview_set_rps() and truncate it to an even value. Also add a comment to chv_freq_opcode() to make sure no one changes the code without considering this requirement. Signed-off-by:
-
Daniel Vetter authored
Signed-off-by:Daniel Vetter <daniel.vetter@intel.com>
-
Oscar Mateo authored
The batchbuffer that sets the render context state is submitted in a different way, and from different places. We needed to make both the render state preparation and free functions outside accesible, and namespace accordingly. This mess is so that all LR, LRC and Execlists functionality can go together in intel_lrc.c: we can fix all of this later on, once the interfaces are clear. v2: Create a separate ctx->rcs_initialized for the Execlists case, as suggested by Chris Wilson. Signed-off-by:
Oscar Mateo <oscar.mateo@intel.com> v3: Setup ring status page in lr_context_deferred_create when the default context is being created. This means that the render state init for the default context is no longer a special case. Execute deferred creation of the default context at the end of logical_ring_init to allow the render state commands to be submitted. Fix style errors reported by checkpatch. Rebased. Signed-off-by:
Thomas Daniel <thomas.daniel@intel.com> Signed-off-by:
-
Daisy Sun authored
BDW supports GT C0 residency reporting in constant time unit. Driver calculates GT utilization based on C0 residency and adjusts RP frequency up/down accordingly. For offscreen workload specificly, set frequency to RP0. Offscreen task is not restricted by frame rate, it can be executed as soon as possible. Transcoding and serilized workload between CPU and GPU both need high GT performance, RP0 is a good option in this case. RC6 will kick in to compensate power consumption when GT is not active. v2: Rebase on recent drm-intel-nightly v3: Add flip timerout monitor, when no flip is deteced within 100ms, set frequency to RP0. Signed-off-by:
Daisy Sun <daisy.sun@intel.com> [torourke: rebased on latest and resolved conflict] Signed-off-by:
Tom O'Rourke <Tom.O'Rourke@intel.com> Acked-by:
-
Ville Syrjälä authored
init_clock_gating() is too late to read out the mem_freq. We already want to print out the GPU MHz numbers before it's called. Move the mem_freq setup to init_gt_powersave(). v2: Also kill the CHV_CZ_CLOCK_FREQ_MODE_* defines Signed-off-by:
-
Ville Syrjälä authored
Use the pixel_size we got from drm_format_plane_cpp() instead of fb->bits_per_pixel/8 when computing the primary plane page/linear offsets. Avoids a few divs and makes the code more future proof against funky pixel formats where bits_per_pixel isn't well defined. This is what we already did in the sprite code. Note that the relevant sprite patch was commit ca320ac4 Author: Chris Wilson <chris@chris-wilson.co.uk> Date: Wed Dec 19 12:14:22 2012 +0000 drm/i915: Use pixel size for computing linear offsets into a sprite This change was required on sprites because they support yuv formats which have fb->bits_per_pixel undefined. Signed-off-by:
-
Ville Syrjälä authored
During driver init we may not have a valid framebuffer for the primary plane even though the plane is enabled due to failed BIOS fb takeover. This means we have to avoid dereferencing the fb in .update_primary_plane() when disabling the plane. The introduction of the primary plane rotation in commit d91a2cb8e5104233c02bbde539bd4ee455ec12ac Author: Sonika Jindal <sonika.jindal@intel.com> Date: Fri Aug 22 14:06:04 2014 +0530 drm/i915: Add 180 degree primary plane rotation support caused a regression by trying to look up the pixel format before we can be sure there's a valid fb available. This isn't entirely unsurprising since the rotation patches originally predate the change to the primary plane code that calls .update_primary_plane() also when disabling the plane: commit fdd508a6 Author: Ville Syrjälä <ville.syrjala@linux.intel.com> Date: Fri Aug 8 21:51:11 2014 +0300 drm/i915: Call .update_primary_plane in intel_{enable, disable}_primary_hw_plane() v2: Warn but don't blow up when trying to enable a plane w/o an fb (Chris) Cc: Sonika Jindal <sonika.jindal@intel.com> Signed-off-by: -
Arun Siluvery authored
The workarounds that are applied are exported to a debugfs file; this is used to verify their state after the test case (reset or suspend/resume etc). This patch is only required to support i-g-t. Signed-off-by:
Arun Siluvery <arun.siluvery@linux.intel.com> Signed-off-by:
-
Arun Siluvery authored
For BDW workarounds are currently initialized in init_clock_gating() but they are lost during reset, suspend/resume etc; this patch moves the WAs that are part of register state context to render ring init fn otherwise default context ends up with incorrect values as they don't get initialized until init_clock_gating fn. v2: Add workarounds to golden render state This method has its own issues, first of all this is different for each gen and it is generated using a tool so adding new workaround and mainitaining them across gens is not a straightforward process. v3: Use LRIs to emit these workarounds (Ville) Instead of modifying the golden render state the same LRIs are emitted from within the driver. v4: Use abstract name when exporting gen specific routines (Chris) For: VIZ-4092 Signed-off-by:
-
Rodrigo Vivi authored
According to spec FBC on BDW and HSW are identical without any gaps. So let's copy the nuke and let FBC really start compressing stuff. Without this patch we can verify with false color that nothing is being compressed. With the nuke in place and false color it is possible to see false color debugs. Unfortunatelly on some rings like BCS on BDW we have to avoid Bits 22:18 on LRIs due to a high risk of hung. So, when using Blt ring for frontbuffer rend cache would never been cleaned and FBC would stop compressing buffer. One alternative is to cache clean on software frontbuffer tracking. v2: Fix rebase conflict. v3: Do not clean cache on BCS ring. Instead use sw frontbuffer tracking. Signed-off-by:
Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by:
-
Jani Nikula authored
Try to avoid confusion with ARRAY_SIZE()/2 and hdmi_level*2. Signed-off-by:
-
Sonika Jindal authored
Renaming the HSW-specific macros for ddi buffer translation slot to denote the slot and not the vswing/pre-emph values as they are platform-dependent. This patch is based on top of the patch series for renaming the DP training vswing/pre-emph defines: http://lists.freedesktop.org/archives/intel-gfx/2014-August/050407.html v2: Creating single macro with argument for slot number (Damien) v3: Adding macro for num of translation entries (Damien) Signed-off-by:
Sonika Jindal <sonika.jindal@intel.com> Reviewed-by:
Damien Lespiau <damien.lespiau@intel.com> Signed-off-by:
-
Jani Nikula authored
Signed-off-by:
-
Damien Lespiau authored
Previously, it was possible for the GPU memory accesses to be swizzled to try to optimize the fetches for tiled buffers. This swizzling was on top of what the memory controller in the uncore already does. With broadwell, we drop that GPU side swizzling, and the corresponding initialization in 3 units (GAM, GT, DE). All those bits are reserved, as specs put it: Before Gen8, there was a historical configuration control field to swizzle address bit[6] for in X/Y tiling modes. This was set in three different places: TILECTL[1:0], ARB_MODE[5:4], and DISP_ARB_CTL[14:13]" For Gen8 the swizzle fields are all reserved, and the CPU's memory controller performs all address swizzling modifications. This also means that user space doesn't have to manually swizzle when accessing tiled buffers from the CPU, and so we always return I915_BIT_6_SWIZZLE_NONE from i915_gem_detect_bit_6_swizzle(), which short-circuits the initialization of the registers mentionned above in i915_gem_init_swizzling(). v2: Refine the explanation a bit more (Daniel) v3: Make it BDW+ specific (Steve) Cc: Steve Aarnio <steve.j.aarnio@linux.intel.com> Signed-off-by:
-
Damien Lespiau authored
Signed-off-by:
-
Damien Lespiau authored
Instead of going through hoops, just put the driver author directly as DRM_AUTHOR() argument. This will also make it consistent when we add Intel to the list. Signed-off-by:
-
Jani Nikula authored
Fix assert_panel_unlocked for vlv/chv, and improve it a bit for non-LVDS. Also don't pretend it works for DDI. There's still work to do to get this right for eDP on PCH platforms, but this is a start. v2: WARN_ON(HAS_DDI) Reviewed-by:
-
Vedang Patel authored
The patch introduces fixes for the debugfs attributes emitted by the i915 driver for GEN8. Currently, it is not emitting the correct attributes which include the status of RC6 states. Change-Id: Ib2068a0cac9a5wq3f228e547fa1a097ad369d242df Signed-off-by:
Vedang Patel <vedang.patel@intel.com> Signed-off-by:
-
Chris Wilson authored
Rather than describing an object as either "snooped or LLC", we can do better as we should know what machine we are running on! Signed-off-by:
-
Paulo Zanoni authored
On BDW we're seeing a problem that after we runtime resume, the outputs connected to DDI C are not detected: they don't appear in the SDEISR register and GMBUS transactions don't work. They stop working at the moment we call intel_opregion_notify_adapter() during runtime suspend, but they don't go back to work when we call the same function during runtime resume. They only work after we do a modeset and call intel_opregion_notify_encoder(), but this point is already too late. While debugging, I tried to pass PCI_D3hot which is the value that matches the spec, and it seems to have solved the problem. I couldn't find any explanation of why this solves the problem, but there's also no documented explanation - besides our code and git log - of why Haswell should use PCI_D1, so keep this for now in order to keep BDW runtime PM working. Also add a comment to point the fact that there's no spec documenting all the weirdness involved here. Cc: kristen.c.accardi@intel.com Testcase: igt/pm_rpm/drm-resources-equal Testcase: igt/pm_rpm/i2c Signed-off-by:
Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by:
-
