- 15 Oct, 2015 25 commits
-
-
Shannon Nelson authored
Save a little stack space and remove unnecessary strncpy() with a little string pointer. Change-ID: Id2719d34710bfc273d3bb445fec085cd04276e88 Signed-off-by:
Shannon Nelson <shannon.nelson@intel.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Anjali Singhai Jain authored
X722 will report Gen 1x1 in the PCI config space as it is on IOSF bus, so skip the PCI bus link/speed check. Change-ID: Icd5f5751dc7fb00dccf0d5dc5a0a644948e7062e Signed-off-by:
Anjali Singhai Jain <anjali.singhai@intel.com> Tested-by:
-
Kevin Scott authored
Store off reported PHY capabilities in link_info structure. Change-ID: Ife0f037c26983ca985dbf79abf33f8f8791369e8 Signed-off-by:
Kevin Scott <kevin.c.scott@intel.com> Tested-by:
-
Shannon Nelson authored
Remove a variable declaration inside an if block hiding an existing declaration at the start of the function. Also remove a forward function declaration that is no longer needed due to code re-organization. Change-ID: I12954668b722718074949c93d74cd20eaacd93e4 Signed-off-by:
-
Shannon Nelson authored
Since the flow-director-atr priv flag was added to our ethtool interface, we don't need the on/off control in debugfs. Change-ID: Ib3b599916434ab30ccd40074e71d7a81609b5bb5 Signed-off-by:
-
Shannon Nelson authored
Even though the device might be in MFP mode, if there's only one partition enabled, then we still have plenty of interrupts for managing the Flow Directory Sideband activity. This patch enables FD SB in this case. This patch also reverses the sense of the conditional in order to remove the negative logic. Change-ID: I9edf211a6219fc8d159b4be9964f9fd7f4e00bc0 Signed-off-by:
-
Mitch Williams authored
This version check only applies to very, very old firmware, that only ran on A0 hardware, which we never shipped and don't support in this driver anyway. Remove it, before somebody gets hurt. Change-ID: I3752d090ff488acf98ee76b075af961e9c968ee4 Signed-off-by:
Mitch Williams <mitch.a.williams@intel.com> Tested-by:
-
Anjali Singhai Jain authored
X722 has a way to work around the descriptor WB issue, this offload helps turn that feature on. Change-ID: I7ffa67622426bfca5a651417b63e3afcfeb60412 Signed-off-by:
-
Catherine Sullivan authored
Only the X722 device now supports 100M SGMII, and nothing supports 100M on 1000Base_T. Change-ID: I6f44dcd818944edd40041410e6de380f4a359a0c Signed-off-by:
Catherine Sullivan <catherine.sullivan@intel.com> Signed-off-by:
-
Neerav Parikh authored
There are several error messages that have been printing when there is no functional issue. These messages should be available at debug message level only. Change-ID: Id91e47bf942c483563995f30d8705fa53acd5aa3 Signed-off-by:
Neerav Parikh <neerav.parikh@intel.com> Signed-off-by:
-
Jesse Brandeburg authored
Some customers wish to be able to control our hardware specific feature called flow director, at runtime. This patch enables ethtool priv flags to control this driver/hardware specific feature. ethtool --set-priv-flags ethX flow-director-atr off NOTE: the ethtool ntuple interface controls the flow-director sideband rules. Change-ID: Iba156350b07fa2ce66f53ded51739f9a3781fe0e Signed-off-by:Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by:
-
Jesse Brandeburg authored
Add nlflags to the function comment for ndo_bridge_setlink. Change-ID: I34c704f307f2a3f7bac3ca4b44e2a094d3d082d6 Signed-off-by:
-
Mark Rustad authored
If the reset never completes, it is necessary to retake the semaphore before returning, because the caller will release the semaphore. Signed-off-by:
Mark Rustad <mark.d.rustad@intel.com> Tested-by:
Darin Miller <darin.j.miller@intel.com> Signed-off-by:
-
Emil Tantilov authored
This patch disables LRO by default in favor of GRO. LRO is incompatible with forwarding and is disabled when forwarding is turned on which makes the default offloads of the driver inconsistent. LRO can still be enabled via ethtool. Signed-off-by:
Emil Tantilov <emil.s.tantilov@intel.com> Tested-by:
-
David S. Miller authored
Or Gerlitz says: ==================== Mellanox driver update, Oct 14 2015 This series contains two more patches from Eli, patch from Majd to support PCI error handlers and a fix from Jack to mlx4 VFs when probed without a provisioned mac address. The patch set applied on top of net-next commit bbb300eb "Merge branch 'bridge-vlan'" changes from V0: - made the health flag int --> bool to address comment from Dave on patch #1 - fixed sparse warning noted by the 0-day build tests in patch #2 ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jack Morgenstein authored
By design, when no default MAC addresses are set in the Hypervisor for VFs, the VFs are passed zero-macs. When such a MAC is received by the VF, it generates a random MAC address and registers that MAC address with the Hypervisor. This random mac generation is currently done in the mlx4_en module. There is a problem, though, if the mlx4_ib module is loaded by a VF before the mlx4_en module. In this case, for RoCE, mlx4_ib will see the un-replaced zero-mac and register that zero-mac as part of QP1 initialization. Having a zero-mac in the port's MAC table creates problems for a Baseboard Management Console. The BMC occasionally sends packets with a zero-mac destination MAC. If there is a zero-mac present in the port's MAC table, the FW will send such BMC packets to the host driver rather than to the wire, and BMC will stop working. To address this problem, we move the replacement of zero-mac addresses with random-mac addresses to procedure mlx4_slave_cap(), which is part of the driver startup for VFs, and is before activation of mlx4_ib and mlx4_en. As a result, zero-mac addresses will never be registered in the port MAC table by the driver. In addition, when mlx4_en does initialize the net device, it needs to set the NET_ADDR_RANDOM flag in the netdev structure if the address was randomly generated. This is done so that udev on the VM does not create a new device name after each VF probe (VM boot and such). To accomplish this, we add a per-port flag in mlx4_dev which gets set whenever mlx4_core replaces a zero-mac with a randomly-generated mac. This flag is examined when mlx4_en initializes the net-device. Fix was suggested by Matan Barak <matanb@mellanox.com> Signed-off-by:
Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
-
Eli Cohen authored
On device initialization, wait till firmware indicates that that it is done with initialization before proceeding to initialize the device. Also update initialization segment layout to match driver/firmware interface definitions. Signed-off-by:
Eli Cohen <eli@mellanox.com> Signed-off-by:
-
Majd Dibbiny authored
This patch implement the pci_error_handlers for mlx5_core which allow the driver to recover from PCI error. Once an error is detected in the PCI, the mlx5_pci_err_detected is called and it: 1) Marks the device to be in 'Internal Error' state. 2) Dispatches an event to the mlx5_ib to flush all the outstanding cqes with error. 3) Returns all the on going commands with error. 4) Unloads the driver. Afterwards, the FW is reset and mlx5_pci_slot_reset is called and it enables the device and restore it's pci state. If the later succeeds, mlx5_pci_resume is called, and it loads the SW stack. Signed-off-by:
Majd Dibbiny <majd@mellanox.com> Signed-off-by:
-
Eli Cohen authored
The detection of a fatal condition has been updated to take into account the state reported by the device or by detecting an all ones read of the firmware version which indicates that the device is not accessible. Signed-off-by:
-
Eric Dumazet authored
At listen() time, there is a small window where listener is visible with a zero backlog, triggering a spurious "Possible SYN flooding on port" message. Nothing prevents us from setting the correct backlog. Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Eric Dumazet authored
As we no longer hold listener lock in fast path, it is possible that a child is created right after listener freed its bound port, if a close() is done while incoming packets are processed. __inet_inherit_port() must detect this and return an error, so that caller can free the child earlier. Fixes: e994b2f0 ("tcp: do not lock listener to process SYN packets") Fixes: 079096f1 ("tcp/dccp: install syn_recv requests into ehash table") Signed-off-by:
-
Axel Lin authored
Use module_phy_driver macro to simplify the code a bit. Signed-off-by:
Axel Lin <axel.lin@ingics.com> Signed-off-by:
-
lipeng authored
this patch fixes a bug in hns driver. the link led is on at the beginning, but at this time the ethernet port is on down status. it needs to reset the led status on init sequence. Signed-off-by:
lipeng <lipeng321@huawei.com> Signed-off-by:
yankejian <yankejian@huawei.com> Signed-off-by:
-
Karen Xie authored
This helps improving the latency of small packets. Signed-off-by:
Rakesh Ranjan <rakesh@chelsio.com> Signed-off-by:
Karen Xie <kxie@chelsio.com> Signed-off-by:
-
David S. Miller authored
Merge tag 'linux-can-next-for-4.4-20151013' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next Marc Kleine-Budde says: ==================== pull-request: can-next 2015-09-17 this is a pull request of 4 patches for net-next/master. Two patches are by Gerhard Bertelsmann, fixing some problems in the sun4i driver. The patch by Arnd Bergmann stops using timeval for the CAN broadcast manager. The last patch by Alexandre Belloni removes the otherwise unused struct at91_can_data from the driver. ==================== Signed-off-by:
-
- 14 Oct, 2015 15 commits
-
-
yankejian authored
this patch adds support to set promisc mode. it configs the queue on init seq when it is on promisc mode.and being enabled or disabled promisc mode by upper level user. Signed-off-by:
Yisen Zhuang <yisen.zhuang@huawei.com> Signed-off-by:
-
Paolo Abeni authored
Revert the commit e2ca690b ("ipv4/icmp: redirect messages can use the ingress daddr as source"), which tried to introduce a more suitable behaviour for ICMP redirect messages generated by VRRP routers. However RFC 5798 section 8.1.1 states: The IPv4 source address of an ICMP redirect should be the address that the end-host used when making its next-hop routing decision. while said commit used the generating packet destination address, which do not match the above and in most cases leads to no redirect packets to be generated. Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller authored
Jeff Kirsher says: ==================== Intel Wired LAN Driver Updates 2015-10-13 This series contains updates to i40e, i40evf, ixgbe and fm10k. Carolyn cleans up ndo_bridge_getlink() by flagging a parameter as __always_unused, since it is never used. Adds a member to the nvm_info struct to store OEM version info to be output either by OID or ethtool. Neerav cleans up a remaining bit shift to use BIT() macro. Mitch fixes the i40evf driver to properly handle calls to its ndo_set_mac_address() method. It did not properly check to see if the override would be allowed by the PF driver, and it never removed the old address from its filter list. Cleaned up the use of i40e_enable_vf_mappings() in i40e_alloc_vfs(), since it is just redundant since we already call it by i40e_reset_vf(). Fixed a possible panic in some circumstances where the firmware may fail to allocate a VSI for a VF by checking the return value from i40e_alloc_vf_res() and don't try to configure the device further if it failed. Greg fixes the parsing of CEE App TLVs so the caller does not have to consider whether the App came from a CEE or IEEE DCBx negotiation. Shannon moves the device ids into a standalone file due to the desire to write user-land drivers (and other requests) without needing the rest of the include files. Catherine adds the ability to save the module information from get_phy_capabilities() to be used to determine which speeds the module supports. Also cleaned up the PHY structure by removing unused members and add the ability to store the PHY capabilities reported by the firmware. Emil modifies ixgbe to ensure that flow control packets initiated by the VF are dropped and reported as spoofed. Jacob cleans up the fm10k driver to avoid buffer overflow by using sprintf(), so convert to using snprintf(). Also fixed the use of an enum as a boolean, so check for the actual value of NETREG_UNINITIALIZED in case it ever changes from the current value of zero. v2: Dropped patch 11 of the original series, which added functions that were never used. ==================== Signed-off-by: -
Jacob Keller authored
Check for actual value NETREG_UNINITIALIZED in case it ever changes from the current value of zero. Signed-off-by:
Jacob Keller <jacob.e.keller@intel.com> Signed-off-by:
Bruce Allan <bruce.w.allan@intel.com> Tested-by:
Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by:
-
Jacob Keller authored
Signed-off-by:
-
Emil Tantilov authored
This patch makes sure that flow control packets initiated by the VF are dropped and reported as spoofed. Flow control packets can be used to limit the throughput or as DOS attack when generated from a VF. Flow control is not supported per VF hence any pause frames generated from a VF are considered malicious. Also cleaned up indentation and some redundant comments. Signed-off-by:
-
Catherine Sullivan authored
Bump. Change-ID: If3cd42f6c1b9546beed60faf9c79faab35216f58 Signed-off-by:
-
Catherine Sullivan authored
Remove unused members in the PHY structure and add a new member to store all the capabilities the PHY has as reported by the FW. This information will help us determine what speeds the device is capable of when link is down. Also add an enum to decode the PHY types the NVM is capable of. Use the phy_types variable to determine what phy types are possible when link is down instead of device id as it will be more accurate. When on a backplane device, we do not support changing any settings, however we should display all the phy_types we are capable of so if we see a backplane dev ID set supported and advertised purely based on the phy_types variable. Change-ID: Ia75d560f1fcd30c54cbfb7458690c5867559a930 Signed-off-by:
-
Catherine Sullivan authored
Add a module_types variable to the link_info struct to save the module information from get_phy_capabilities. This information can be used to determine which speeds the module supports. Also add a new function update_link_info which updates the module_types parameter and then calls get_link_info. This function should be called in place of get_link_info so that the module_types variable stays up-to-date with the rest of the link information. The EAS table does not reflect the values that are actually returned, so instead, basing these values on the Ethernet compliance codes specified in table 33 of SFF-8436 as these have been accurate. Use the new variable in ethtool to differentiate between a 10G/1G dual speed fiber module and a 10G only module. Change-ID: Ib7585cce321319c10ce15180054c41a6cbd41389 Signed-off-by:
-
Shannon Nelson authored
Due to desires to write userland drivers, and other requests, without needing the rest of the include files, the device ids are pulled out into a standalone file. Change-ID: Ic0b047dbf9d4b0891892309c1f2079f56d9b60e8 Signed-off-by:
-
Carolyn Wyborny authored
This patch moves the internal fw version and fw api version info to be output in probe. The nvm version, etrack and oem version info are now configured for output via ethtool -i. Change-ID: I05d490093a7137dbefcdef263d014d1e5c9e83d0 Signed-off-by:
Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by:
-
Mitch Williams authored
In some circumstances, the firmware may fail to allocate a VSI for a VF. When this happens, the driver does not react well to the bad news and has a panic attack. To fix this problem, check the return value from i40e_alloc_vf_res and don't try to configure the device further if it failed. Additionally, explicitly clear the INIT bit when we free VF resources, so that this bit will be in the proper state in the failure case, and won't blow up elsewhere. Change-ID: I6a20ce2b59c3458fd832032e88fa28cd42500189 Signed-off-by:
-
Mitch Williams authored
This function call isn't needed here; the same function is already called by i40e_reset_vf. Change-ID: I96ccbf91b752965c9e28fe895d4c7d4c46e3ba44 Signed-off-by:
-
Greg Bowers authored
Changes the parsing of CEE App TLVs to fill in the App selector in struct i40e_dcbx_config with the IEEE App selector so the caller doesn't have to consider whether the App came from a CEE or IEEE DCBX negotiation. Change-ID: Ia7d9d664cde04d2ebcc9822fd22e4929c6edab3a Signed-off-by:
Greg Bowers <gregory.j.bowers@intel.com> Tested-by:
-
Carolyn Wyborny authored
This patch adds a member to the nvm_info struct for oem_ver info to be output either by OID or ethtool. Change-ID: I1e5d513ae67622e2af17042924fdb4b5d6d85366 Signed-off-by:
-
