The PCI IRQ map for the old Motorola PowerStackII (Utah) boards was
incorrect, but this breakage wasn't exposed until 2.5, and finally fixed
until recently by Sebastian Heutling <sheutlin@gmx.de>.
Signed-off-by: Christian Kujau <evil@g-house.de>
Signed-off-by: Tom Rini <trini@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This patches fixes the return code from cciss_ioctl.  Without this some
block layer (BLK*) ioctls do not work.

Thanks to Jens Axboe for pointing this out.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

We recently found a problem that was causing memory corruption during boot
on IBM POWER5 machines.  The problem was that the if you have a USB
keyboard and it is set to the input device for the firmware, it will still
be active when the kernel is started.  That means that the OHCI controller
has pointers to various memory areas that it polls for transfers to do. 
When we start using that same memory in the kernel, bad things can happen. 
(This isn't a problem on powermacs because the Apple OF implements a
"quiesce" call which turns off all the devices it is using.)

This patch fixes the problem by calling the Open Firmware "close" method
for the input device.  Stephen Rothwell and I have verified that doing this
fixes the problem on the POWER5 machine where we observed it.  I verified
that this patch doesn't cause any problems on powermacs.

I think this patch should go into 2.6.10 since it fixes a nasty memory
corruption bug that can cause rather subtle and hard-to-diagnose problems
during boot.  (The symptom on the POWER5 machine with the particular kernel
that we were using was that reading /proc/net/tcp would oops, due to one of
the pointers in tcp_ehash being corrupted.)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Fix eepro100 driver suspend/resume issue.

Signed-off-by: Li Shaohua<shaohua.li@intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Current cfq can cause hangs with non-fs requests, because the accounting
goes bad.  This fixes it.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

M68k: Update defconfigs for 2.6.10-rc3
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

The D-Link DGE-528T gigabit adapter is based on the 8169 chipset (reported
by Andreas Tauscher <ta@lonestar-bbs.de>, checked in the sources of a
driver for this adapter).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

The isolcpus option is broken in 2.6.10-rc2-bk2.  The domains are no longer
being properly initialized (which results in a panic at bootup).
Signed-off-by: Dimitri Sivanich <sivanich@sgi.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

The PowerMac specific sleep code in the OHCI USB driver used to call
disable/enable irq, which is no longer necessary and actually clashes with
the calls to free/request_irq that the common OHCI code now does, thus
causing WARN_ON's to trigger each time a PowerBook is woken up from sleep.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

If given no-hlt kernel option, ia32 idle loop turns out to be a spin loop. 
Add cpu_relax() in this spin loop because IA32 SDM recommends that a PAUSE
instruction be put in all spin loops.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

There's a chance that the receive buffers are being consumed at the same
rate as they are being replenished in ibmveth_replenish_task()... 
Meanwhile, the calls to schedule_replenishing() from ibmveth_poll() won't
schedule another replenishing cycle (because the not_replenishing flag is
zero), starving the buffers and making the adapter unable to receive
packets unless the module is reloaded...  Here's a small patch that will
fix it by scheduling another replenishing task after toggling the
not_replenishing flag.
Signed-Off-By: Santiago Leon <santil@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Fix the non-normalized wall_to_monotonic for i386 and m32r (The other archs
seem to get it right)
Signed-off-by: Herbert Poetzl <herbert@13thfloor.at>
Signed-off-by: George Anzinger <george@mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

into ppc970.osdl.org:/home/torvalds/v2.6/linux

Patch from David Vrabel

Fix a minor typo in the MODULE_AUTHOR string in ixp4xx_wdt.

Signed-off-by: David Vrabel
Signed-off-by: Russell King

Patch from Marc Singer

Add support for the LPD7a40x implementation of the SMC91x ethernet
controller. This patch exists to work around a mismatch between the
way the LH7a40x CPUs handle chip selects and what the ethernet
controller expects.

This patch has been revised to eliminate masking of interrupts.  The
concessions are that 

  a) the ISR must perform an IOBARRIER before the first access to the
     chip, just in case the interrupt occurred while the driver was
     writing to the chip
  b) other drivers that use the same chip select region as the SMC
     chip must perform a similar IOBARRIER at the top of their ISRs.

Signed-off-by: Marc Singer
Signed-off-by: Russell King

Patch from Marc Singer

A missing exten prevented the 2.6.10-rc2 kernel from building for the
LPD7A404.  This patch adds it.

Signed-off-by: Marc Singer
Signed-off-by: Russell King

Patch from Holger Hans Peter Freyther

As proposed in 2282 asm-arm/arch-sa1100/ide.h is not included anymore from asm-arm/ide.h. 
If arch-sa1100/ide.h is included we abort with #error.
If lart.c is compiled we kindly warn that ide needs fixing for this board.


Signed-off-by: Holger Hans Peter Freyther
Signed-off-by: Russell King

Patch from Marc Singer

Some typos prevent the 2.6.10-rc2 kernel from building for the
LPD7A400.  This patch fixes them.  It also removes CONFIG_FIQ which
shouldn't be necessary and doesn't compile.

Signed-off-by: Marc Singer
Signed-off-by: Russell King

Some time ago, a patch was merged that removed pci_save_state() and
pci_restore_state() from various ALSA drivers. That patch also added
pci_restore_state() to sound/core/init.c but didn't add pci_save_state()
anywhere. This is needed since the core pci handling doesn't do this for
us anymore.

My laptop doesn't resume (gets what I assume is an ACPI timeout and
hangs solid) without this small obvious patch.
Signed-off-by: Martin Josefsson <gandalf@wlug.westbo.se>
Fixed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

into ppc970.osdl.org:/home/torvalds/v2.6/linux

Use milliseconds internally for these delays, and convert them
to centiseconds at the interface boundary to the ioctl
configuration controls.

into ppc970.osdl.org:/home/torvalds/v2.6/linux

We have to load the bigkernel second TLB entry on
secondary processors before we move over the use
the kernel trap table.  Otherwise we can take a
TLB miss somewhere in the post-4MB area and the
TLB handler is not prepared to service that.

The case that usually occurs is the prom_set_trap_table
call made by trampoline.S, since p1275buf usually sits
very near the end of the kernel image.  It worked by
luck most of the time as long as p1275buf sits within
a single page since earlier code running in trampoline.S
forced that TLB entry to be loaded by the OBP TLB miss
handler.

This was not fun to figure out.
Signed-off-by: David S. Miller <davem@davemloft.net>

into ppc970.osdl.org:/home/torvalds/v2.6/linux

Always pass values to get_user and put_user in an even numbered
register, and optionally the next odd numbered register.  This
ensures that we are compatible with compiler enhancements.

Patch from Ben Dooks

A simple divide is not enough for the s3c2410 default
timer code, due to most clocks not being a nice multiple
of usecs.

This update changes the calculation of the usec to use
multipliers and shifts to effect a fast divide by a non-integer
number.

Original patch by Dimitry Andric, updated by Ben Dooks

Signed-off-by: Dimitry Andric

Signed-off-by: Ben Dooks
Signed-off-by: Russell King

Ok, here we go (finally).  A patch to correct the cut-and-paste
copyright in arch/ia64/kernel/domain.c.  Both Silicon Graphics, Inc. 
and myself (yes personally) hold the copyright on this file.
Signed-off-by: Jesse Barnes <jbarnes@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

sysfs_dir_close did not free the "cursor" sysfs_dirent used for keeping
track of position in the list of sysfs_dirent nodes.  Consequently,
doing a "find /sys" would leak a sysfs_dirent for each of the 1140
directories in my /sys tree, or about 36kB each time.


From: "Adam J. Richter" <adam@yggdrasil.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

proc_pid_status dereferences pointers in the task structure even if the
task is already dead.  This is probably the reason for the oops described
in

http://bugme.osdl.org/show_bug.cgi?id=3812

The attached patch removes the pointer dereferences by using pid_alive()
for testing that the task structure contents is still valid before
dereferencing them.  The task structure itself is guaranteed to be valid -
we hold a reference count.
Signed-Off-By: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Prevent X86_VISWS config from building APM support.  APM isn't supported
and it won't build if attempted.  Also disable P4THERMAL for VISWS.
Signed-off-by: Randy Dunlap <rddunlap@osdl.org>
Acked-by: Andrey Panin <pazke@donpac.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Specify an initial value signal_struct's field stop_state whenever a
signal_struct variable is created.

Bug was discovered through the occasional failure of telnet(1) to connect.
Signed-off-by: Joe Korty <joe.korty@ccur.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Timothy Lee reports:

Hardware: CyberBlade/i1 on VIA Epia-800

Problem Description:  When the framebuffer is set to 16 bpp, console's text
colours are incorrect.  For example, white becomes yellow, black becomes blue, etc.

Steps to reproduce:
1. Load tridentfb
2. Use "setterm -n -depth 16" to request 16 bpp framebuffer

The problem arose from the fact that each psuedo palette entry should be
32-bit in size, even under 16-bit display mode.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This patch fixes annoying warnings in ibm_emac driver.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This change brings the semantics equivalent to 2.4 and also to what the man
page says; Also optimises by avoiding unneeded lookup in uid cache, when
who is same as the current->uid.

sys_set/getpriority is rewritten in 2.5/2.6, perhaps while transitioning to
the pid maps.  It has now semantical bug, when uid is zero.  Note that akpm
also fixed refcount leak and locking in the new functions in changeset
http://linus.bkbits.net:8080/linux-2.5/cset@1.1608.10.84

Signed-off-by: <pmeda@akamai.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This patch avoids a deadlock on rtnl_sem in smc_close() when bringing down
an smc91x interface.  The semaphore is already held by devinet_ioctl() and
the pending work queue contains linkwatch_event() (scheduled by
netif_carrier_off()) which also wants rtnl_sem hence it is unsafe to call
flush_scheduled_work().

The solution is to track whether we have any pending work of our own and
wait for that instead of flushing the entire queue.

I also fixed a typo 'ence' -> 'Hence' and renamed smc_detect_phy to
smc_phy_detect in order to follow the same pattern as the other smc_phy_*
functions.
Signed-off-by: Ian Campbell <icampbell@arcom.com>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

HP Lance Ethernet depends on DIO bus support
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>