- 01 Apr, 2007 30 commits
-
-
Brian King authored
Bump driver version. Signed-off-by:
Brian King <brking@linux.vnet.ibm.com> Signed-off-by:
James Bottomley <James.Bottomley@SteelEye.com>
-
Brian King authored
Improve overall command performance by embedding the scatterlist in the command block used by the adapter. This decreases the overall number of DMAs required for a single command. Signed-off-by:
-
Brian King authored
If qc_issue fails for some reason, return a better error to libata. Signed-off-by:
-
Brian King authored
Add entry in ipr error translation table for an error received when a device is forced into the failed state by the user. Signed-off-by:
-
Brian King authored
Add the ability to control how much error data gets logged on a per error basis. Signed-off-by:
-
Brian King authored
Fix to make sure user config accesses get re-enabled if the PCI config write to start BIST fails. Signed-off-by:
-
Brian King authored
This patch fixes a problem discovered on a system with some bad SATA devices attached. If a command to a SATAPI device times out and the device gets reset as part of error recovery, its possible that ipr will set err_mask to indicate a device error has occurred. If this happens, a request sense will get issued by libata. Since scsi core thinks this scsi command is now completed, because the device reset handler completed successfully, scsi core will free the associated scsi command, which may cause an oops when that request sense is completed later by ipr. This patch ensures that any commands that get aborted as a result of a device reset set err_mask appropriately so that the request sense does not get sent. Signed-off-by:
-
Brian King authored
For ipr SAS adapters that support dual pathing, this patch modifies ipr to log an error when a path fails. Signed-off-by:
-
Brian King authored
The ipr driver has a sysfs attribute which can be used to adjust the logging level of the driver for error events. The error response data for commands can be dumped by increasing the logging level of the ipr driver. This currently only works for JBOD passthrough devices. This patch enables this function for all devices, including RAID devices, to aid in debugging problems. Signed-off-by:
-
Brian King authored
Adds support for some new PCI-E ipr adapters. Signed-off-by:
-
Brian King authored
Remove the auto RAID 0 array creation module parameter, since support for this function has been removed from the firmware. Signed-off-by:
-
Brian King authored
Some ipr adapters may take longer than others to come operational. This patch makes this timeout different for different adapters, while still preserving the module parameter which can be used to globally override the default. Signed-off-by:
-
Robert Jennings authored
Fixed the kernel-doc comment for ibmvscsi_slave_configure. Thanks to Randy Dunlap for pointing this out. Adding a slave_configure function for the driver. Now the disks can be restarted by the scsi mid-layer when the are disconnected and reconnected. Signed-off-by:
"Robert Jennings" <rcj@linux.vnet.ibm.com> Signed-off-by:
"Santiago Leon" <santil@us.ibm.com> Signed-off-by:
-
Robert Jennings authored
The request limit calculations used previously on the client failed to mirror the state of the server. Additionally, when a value < 3 was provided there could be problems setting can_queue and handling abort and reset commands. Signed-off-by:
-
Salyzyn, Mark authored
The Adapter build date that is to be printed on instantiation was not displayed as a result of the supplemental adapter information structure not being in sync with the Firmware; the driver took an early test cycle version that had a miss-sized padded region at the head and the structure was not re-checked at the end of qualification. The Build Date was not a priority and is merely a cosmetic enhancement, and the wrong location for the start of the structure member would not induce any side-effect problems. We updated the structure to match the actual format, and added the TSID (Tech Support Identification) value print, should it be present, to the adapter instantiation announcements during driver load. This later enhancement should improve the relationship between Service folk & Tech Support if the printed value of the TSID found it's way into the circular file labeled G... Neither of these values show in sysfs (yet). Signed-off-by:
Mark Salyzyn <aacraid@adaptec.com> Signed-off-by:
-
Salyzyn, Mark authored
Just sweeping the floor clean in one spot. Some of these constants have never been used in the driver or in the firmware (and thus are meaningless). Triggered this patch because I discovered one of the unused constants was actually incorrect and figured it was better to clean them out than correct and update. There are no side effects at all regarding this patch, it is purely cosmetic. Signed-off-by:
-
Christof Schmitt authored
Correctly initialize the timer for FSF requests with jiffies + timeout. Cc: Swen Schillig <swen@vnet.ibm.com> Acked-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by:
Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by:
-
Bernhard Walle authored
On the path qla2x00_probe_one() -> probe_failed -> qla2x00_free_device(), pci_disable_device() is executed twice, once in qla2x00_free_device() and once in qla2x00_probe_one(). This patch removes the unnecessary call. Signed-off-by:
Bernhard Walle <bwalle@suse.de> Acked-by:
Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by:
-
Salyzyn, Mark authored
Unsigned long is not always the same size as a pointer, namely on 32 bit systems with 64 bit address space. Ptrdiff_t is the same size as a pointer in all configurations. By using ptrdiff_t we can mitigate the warning messages on these configurations. There should be no side effects of this patch. Signed-off-by:
-
Salyzyn, Mark authored
Add SMC and SUN products to aacraid documentation Signed-off-by:
-
Adrian Bunk authored
Signed-off-by:
Adrian Bunk <bunk@stusta.de> Acked-by:
Hannes Reinecke <hare@suse.de> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Adrian Bunk authored
- proper prototypes for global code in aacraid.h - aac_rx_start_adapter() can now become static Signed-off-by:
"Salyzyn, Mark" <mark_salyzyn@adaptec.com> Signed-off-by:
-
Adrian Bunk authored
The Coverity checker spotted this dead code introduced by commit a07f3537. Signed-off-by:
-
Adrian Bunk authored
Signed-off-by:
Eric Moore <Eric.Moore@lsi.com> Signed-off-by:
-
Robert P. J. Day authored
Remove the unused SCSI-related kernel config variables SCSI_NCR53C8XX_PROFILE_SUPPORT SCSI_NCR53C8XX_PROFILE 53C700_IO_MAPPED AIC79XX_ENABLE_RD_STRM AIC7XXX_PROBE_EISA_VL Signed-off-by:
Robert P. J. Day <rpjday@mindspring.com> Signed-off-by:
-
Henne authored
Remove some trailing whitespaces and some replace whitespaces with tabs. Signed-off-by:
Henrik Kretzschmar <henne@nachtwindheim.de> Signed-off-by:
-
Robert P. J. Day authored
Remove the Kconfig requirement that the PCMCIA SCSI drivers be built only as modules, and allow them to be built into the kernel. Signed-off-by:
Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by:
-
Salyzyn, Mark authored
Add some likely() and unlikely() compiler hints in some of the aacraid hardware interface layers. There should be no operational side effects resulting from this patch and the changes should be mostly benign on x86 platforms. Signed-off-by:
-
Richard Lary authored
This patch fixes byte swap issue in qla2xxx driver to fix corrupted fabric_name passed to /sys/class/fc_host/host*/fabric_name. Signed-off-by:
Richard Lary <rlary@us.ibm.com> Acked-by:
Seokmann Ju <seokmann.ju@qlogic.com> Signed-off-by:
-
Anton Blanchard authored
We have seen two cases where VPD on an emulex card has been incorrect and we end up walking off the end of memory. It looks like someone made an update (increased the length of a string) without increasing the Length field. Then we do: Length -= (3+i); And since Length is unsigned it becomes very large and we loop forever in the encapsulating: while (Length > 0) { If we make Length signed then we fall out of the loop and proceed on. Its important to note we have only seen this in the lab and it may be the only two cases of this in existence, but since the rest of the code has been written to be resilient against bad VPD we may as well fix this too. Signed-off-by:Anton Blanchard <anton@samba.org> Acked-by:
James Smart <James.Smart@Emulex.Com> Signed-off-by:
-
- 21 Mar, 2007 3 commits
-
-
Salyzyn, Mark authored
There is some residual cleanup of the last series of patches and the need to bump the revision number to draw the line in the sand. The cmd->SCp.phase is set in the aac_valid_context routine, then set again to the same value following it's return. The cmd->scsi_done is set twice in the aac_queuecommand routine. Free up the scsidev FILO in aac_probe_container as it is not needed further down the function in any case. Improve the efficiency of the abort handler kernel print parameters. Bump revision number of driver to approximate the equivalent in the Adaptec supplied version. Signed-off-by:
-
Salyzyn, Mark authored
Captured a panic on an older kernel where an application issuing commands via sg was sending requests that lacked a request_buffer, thus the buffer pointer used in aac_internal_transer was NULL. The application was fixed closing the issue, but felt it was advised to immunize the driver against the eventuality. Signed-off-by:
-
James Bottomley authored
The #ifdef MODULE around the export of scsi_complete_async_scans() which is the API the scsi_wait_scan module uses is incorrect and causes the symbol to be undefined in certain circumstances leading to a build failure. Remove the defines. Signed-off-by:
-
- 20 Mar, 2007 7 commits
-
-
James Bottomley authored
Signed-off-by: -
Tejun Heo authored
Implement SBC START/STOP management. sdev->mange_start_stop is added. When it's set to one, sd STOPs the device on suspend and shutdown and STARTs it on resume. sdev->manage_start_stop defaults is in sdev instead of scsi_disk cdev to allow ->slave_config() override the default configuration but is exported under scsi_disk sysfs node as sdev->allow_restart is. When manage_start_stop is zero (the default value), this patch doesn't introduce any behavior change. Signed-off-by:
Tejun Heo <htejun@gmail.com> Rejections fixed and Signed-off-by:
-
Tejun Heo authored
sd_sync_cache() should return -errno on error, fix it. Signed-off-by:
-
Eric Moore authored
This address the issue of VMWare guest OS being remounted as read-only becuase the underlying device was held busy too long and at the same time address Engenio MPP driver concerns over infinite retries. This patch removes the code that snoops the SAM STATUS on busy, which would be returning DID_BUS_BUSY, instead we return the status as is. Retry hanlding seems to be properly handled in scsi_softirq_done, where a busy sam status would only occurr for the time specified by (cmd->allowed +1) * cmd->timeout_per_command. Signed-off-by:
-
Horms authored
Honour the return value of pci_enable_device(), which seems to be a desirable thing to do: 2.6.20-rc4 gcc (GCC) 4.1.2 20061115 (prerelease) (Debian 4.1.1-21) CC [M] drivers/message/fusion/mptbase.o drivers/message/fusion/mptbase.c: In function `mpt_resume': drivers/message/fusion/mptbase.c:1541: warning: ignoring return value of `pci_enable_device', declared with attribute warn_unused_result It also in turn has mptscsih_resume() honour the return value of mpt_resume() I'm not sure about the handling of the other potential error cases in mpt_resume(), of which there appear to be many. But this does seem to be a good start. Signed-off-by:Simon Horman <horms@verge.net.au> Acked-by:
-
Horms authored
It seems that most of the code in mptscsih_resume() doesn't do anything. This patch removes that code. Signed-off-by:
-
Richard Knutsson authored
eata_generic.h is only included by eata_pio.c and it only uses FALSE/TRUE in comments. Signed-off-by:
Richard Knutsson <ricknu-0@student.ltu.se> Signed-off-by:
-
