Merge tag 'for-v3.16-rc/omap-fixes-b' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.16/fixes

Some miscellaneous fixes for OMAP clock code, DRA7xx device data, and
PRCM code (when DSPBridge is used) for v3.16-rc.

Basic build, boot, and PM test logs are available here:

http://www.pwsan.com/omap/testlogs/prcm-a-v3.16-rc/20140706174258/

As this board use external clock for RMII interface we should specify 'rmii'
phy mode and 'rmii-clock-ext' to make ethernet working.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The use of FIFO in McASP can reduce the risk of audio under/overrun and
lowers the load on the memories since the DMA will operate in bursts.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The use of FIFO in McASP can reduce the risk of audio under/overrun and
lowers the load on the memories since the DMA will operate in bursts.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Currently, child nodes of the gpmc node are iterated and probed
regardless of their 'status' property. This means adding 'status =
"disabled";' has no effect.

This patch changes the iteration to only probe nodes marked as
available.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Tested-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The DSP platform device for TI DSP/Bridge is currently
created unconditionally whenever CONFIG_TIDSPBRIDGE is
enabled. This device should only be created on OMAP34xx/
OMAP36xx SoCs, and not for other OMAP3 derived SoCs or when
booting multi-arch images on other SoCs. So, add a check for
the SoC family both before creating the device and allocating
the carveout memory for the device.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

After clarification from the hardware team it was found that
this 1.8V PHY supply can't be switched OFF when SoC is Active.

Since the PHY IPs don't contain isolation logic built in the design to
allow the power rail to be switched off, there is a very high risk
of IP reliability and additional leakage paths which can result in
additional power consumption.

The only scenario where this rail can be switched off is part of Power on
reset sequencing, but it needs to be kept always-on during operation.

This patch is required for proper functionality of USB, SATA
and PCIe on DRA7-evm.

CC: Rajendra Nayak <rnayak@ti.com>
CC: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

omap44xx_restart is defined as a static void inline when DRA7/AM437X is
defined alone, which implies that the restart function is no longer
functional even though it is built in. So, fix the definition of the
same.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The divider value provided to the _dpll_test_fint can reach value of
256 with J type DPLLs (USB etc.), which causes an overflow with the u8
datatype. Fix this by changing the parameter to be an int instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[paul@pwsan.com: changed type of 'n' to unsigned int]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Add the sysconfig class bits for the Super Speed USB
controllers
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Get rid of optional clock as that is now managed by the
AHCI platform driver.

Correct .mpu_rt_idx to 1 as the module register space (SYSCONFIG..)
is passed as the second memory resource in the device tree.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

The commit 7be914f2 {ARM: OMAP3: PRM/CM: Cleanup unused header} removed
some of the macros used by the TI DSP/Bridge driver. This fixes the
following build errors when trying to build DSP/Bridge driver (disabled
at present), otherwise results in the following build errors:

drivers/staging/tidspbridge/core/tiomap3430.c:531:31: error: 'OMAP3430_AUTO_IVA2_DPLL_SHIFT' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap3430.c:531:31: note: each undeclared identifier is reported only once for each function it appears in
make[3]: *** [drivers/staging/tidspbridge/core/tiomap3430.o] Error 1
make[3]: *** Waiting for unfinished jobs....
drivers/staging/tidspbridge/core/tiomap_io.c: In function 'sm_interrupt_dsp':
drivers/staging/tidspbridge/core/tiomap_io.c:404:31: error: 'OMAP3430_AUTO_IVA2_DPLL_SHIFT' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap_io.c:404:31: note: each undeclared identifier is reported only once for each function it appears in
drivers/staging/tidspbridge/core/tiomap_io.c:414:12: error: 'OMAP3430_IVA2_DPLL_FREQSEL_SHIFT' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap_io.c:415:12: error: 'OMAP3430_EN_IVA2_DPLL_SHIFT' undeclared (first use in this function)
make[3]: *** [drivers/staging/tidspbridge/core/tiomap_io.o] Error 1
drivers/staging/tidspbridge/core/tiomap3430_pwr.c: In function 'dsp_clk_wakeup_event_ctrl':
drivers/staging/tidspbridge/core/tiomap3430_pwr.c:442:19: error: 'OMAP3430_GRPSEL_GPT5_MASK' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap3430_pwr.c:442:19: note: each undeclared identifier is reported only once for each function it appears in
drivers/staging/tidspbridge/core/tiomap3430_pwr.c:455:19: error: 'OMAP3430_GRPSEL_GPT6_MASK' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap3430_pwr.c:468:19: error: 'OMAP3430_GRPSEL_GPT7_MASK' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap3430_pwr.c:481:19: error: 'OMAP3430_GRPSEL_GPT8_MASK' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap3430_pwr.c:494:19: error: 'OMAP3430_GRPSEL_MCBSP1_MASK' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap3430_pwr.c:546:19: error: 'OMAP3430_GRPSEL_MCBSP5_MASK' undeclared (first use in this function)
make[3]: *** [drivers/staging/tidspbridge/core/tiomap3430_pwr.o] Error 1
make[2]: *** [drivers/staging/tidspbridge] Error 2

Fixes: 7be914f2 (ARM: OMAP3: PRM/CM: Cleanup unused header)
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Pull devicetree bugfix from Grant Likely:
 "Important bug fix for parsing 64-bit addresses on 32-bit platforms.
  Without this patch the kernel will try to use memory ranges that
  cannot be reached"

* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux:
  of: Check for phys_addr_t overflows in early_init_dt_add_memory_arch

Pull SCSI fixes from James Bottomley:
 "This is a set of 13 fixes, a MAINTAINERS update and a sparse update.
  The fixes are mostly correct value initialisations, avoiding NULL
  derefs and some uninitialised pointer avoidance.

  All the patches have been incubated in -next for a few days.  The
  final patch (use the scsi data buffer length to extract transfer size)
  has been rebased to add a cc to stable, but only the commit message
  has changed"

* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  [SCSI] use the scsi data buffer length to extract transfer size
  virtio-scsi: fix various bad behavior on aborted requests
  virtio-scsi: avoid cancelling uninitialized work items
  ibmvscsi: Add memory barriers for send / receive
  ibmvscsi: Abort init sequence during error recovery
  qla2xxx: Fix sparse warning in qla_target.c.
  bnx2fc: Improve stats update mechanism
  bnx2fc: do not scan uninitialized lists in case of error.
  fc: ensure scan_work isn't active when freeing fc_rport
  pm8001: Fix potential null pointer dereference and memory leak.
  MAINTAINERS: Update LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI) maintainers Email IDs
  be2iscsi: remove potential junk pointer free
  be2iscsi: add an missing goto in error path
  scsi_error: set DID_TIME_OUT correctly
  scsi_error: fix invalid setting of host byte

Pull drm fixes from Dave Airlie:
 "i915, tda998x and vmwgfx fixes,

  The main one is i915 fix for missing VGA connectors, along with some
  fixes for the tda998x from Russell fixing some modesetting problems.

  (still on holidays, but got a spare moment to find these)"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/vmwgfx: Fix incorrect write to read-only register v2:
  drm/i915: Drop early VLV WA to fix Voltage not getting dropped to Vmin
  drm/i915: only apply crt_present check on VLV
  drm/i915: Wait for vblank after enabling the primary plane on BDW
  drm/i2c: tda998x: add some basic mode validation
  drm/i2c: tda998x: faster polling for edid
  drm/i2c: tda998x: move drm_i2c_encoder_destroy call

Pull ARM SoC fixes from Olof Johansson:
 "This week's arm-soc fixes:

   - A set of of OMAP patches that we had missed Tony's pull request of:
     * Reset fix for am43xx
     * Proper OPP table for omap5
     * Fix for SoC detection of one of the DRA7 SoCs
     * hwmod updates to get SATA and OCP to work on omap5 (drivers
       merged in 3.16)
     * ... plus a handful of smaller fixes
   - sunxi needed to re-add machine specific restart code that was
     removed in anticipation of a watchdog driver being merged for 3.16,
     and it didn't make it in.
   - Marvell fixes for PCIe on SMP and a big-endian fix.
   - A trivial defconfig update to make my capri test board boot with
     bcm_defconfig again.

  ... and a couple of MAINTAINERS updates, one to claim new Keystone
  drivers that have been merged, and one to merge MXS and i.MX (both
  Freescale platforms).

  The largest diffs come from the hwmod code for omap5 and the re-add of
  the restart code on sunxi.  The hwmod stuff is quite late at this
  point but it slipped through cracks repeatedly while coming up the
  maintainer chain and only affects the one SoC so risk is low"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  MAINTAINERS: Add few more Keystone drivers
  MAINTAINERS: merge MXS entry into IMX one
  ARM: sunxi: Reintroduce the restart code for A10/A20 SoCs
  ARM: mvebu: fix cpuidle implementation to work on big-endian systems
  ARM: mvebu: update L2/PCIe deadlock workaround after L2CC cleanup
  ARM: mvebu: move Armada 375 external abort logic as a quirk
  ARM: bcm: Fix bcm and multi_v7 defconfigs
  ARM: dts: dra7-evm: remove interrupt binding
  ARM: OMAP2+: Fix parser-bug in platform muxing code
  ARM: DTS: dra7/dra7xx-clocks: ATL related changes
  ARM: OMAP2+: drop unused function
  ARM: dts: am43x-epos-evm: Add Missing cpsw-phy-sel for am43x-epos-evm
  ARM: dts: omap5: Update CPU OPP table as per final production Manual
  ARM: DRA722: add detection of SoC information
  ARM: dts: Enable twl4030 off-idle configuration for selected omaps
  ARM: OMAP5: hwmod: Add ocp2scp3 and sata hwmods
  ARM: OMAP2+: hwmod: Change hardreset soc_ops for AM43XX

Pull irq fixes from Thomas Gleixner:
 "A few minor fixlets in ARM SoC irq drivers and a fix for a memory leak
  which I introduced in the last round of cleanups :("

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq: Fix memory leak when calling irq_free_hwirqs()
  irqchip: spear_shirq: Fix interrupt offset
  irqchip: brcmstb-l2: Level-2 interrupts are edge sensitive
  irqchip: armada-370-xp: Mask all interrupts during initialization.

Fixes for 3.16-rc3; most importantly Jesse brings back VGA he took away
on a bunch of machines. Also a vblank fix for BDW and a power workaround
fix for VLV.

* tag 'drm-intel-fixes-2014-07-03' of git://anongit.freedesktop.org/drm-intel:
  drm/i915: Drop early VLV WA to fix Voltage not getting dropped to Vmin
  drm/i915: only apply crt_present check on VLV
  drm/i915: Wait for vblank after enabling the primary plane on BDW

fix to a 3.15 commit.

* 'vmwgfx-fixes-3.16' of git://people.freedesktop.org/~thomash/linux:
  drm/vmwgfx: Fix incorrect write to read-only register v2:

mode fixes for tda998x.

* 'tda998x-fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-cubox:
  drm/i2c: tda998x: add some basic mode validation
  drm/i2c: tda998x: faster polling for edid
  drm/i2c: tda998x: move drm_i2c_encoder_destroy call

irq_free_hwirqs() always calls irq_free_descs() with a cnt == 0
which makes it a no-op since the interrupt count to free is
decremented in itself.

Fixes: 7b6ef126Signed-off-by: Keith Busch <keith.busch@intel.com>
Acked-by: David Rientjes <rientjes@google.com>
Link: http://lkml.kernel.org/r/1404167084-8070-1-git-send-email-keith.busch@intel.comSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

Pull ARM64 fixes from Catalin Marinas:
 - Exception level check at boot time (for completeness, not triggering
   any bug before)
 - I/D-cache synchronisation logic for huge pages
 - Config symbol typo

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: fix el2_setup check of CurrentEL
  arm64: mm: Make icache synchronisation logic huge page aware
  arm64: mm: Fix horrendous config typo

Update MAINTAINERS file for recently added reset controller, AEMIF
and clocksource driver for Keystone SOCs.

The EMIF memory controller driver is also added along with AEMIF.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

The mach-mxs platform is actually co-maintained by myself and
pengutronix folks.  Also it's hosted in the same kernel tree as IMX.
So let's merge the entry into IMX one.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Olof Johansson <olof@lixom.net>

mvebu fixes for v3.16 (round #2)

 - mvebu
    - Fix PCIe deadlock now that SMP is enabled
    - Fix cpuidle for big-endian systems

* tag 'mvebu-fixes-3.16-2' of git://git.infradead.org/linux-mvebu:
  ARM: mvebu: fix cpuidle implementation to work on big-endian systems
  ARM: mvebu: update L2/PCIe deadlock workaround after L2CC cleanup
  ARM: mvebu: move Armada 375 external abort logic as a quirk
Signed-off-by: Olof Johansson <olof@lixom.net>

This partly reverts commits 55360050 (ARM: sunxi: Remove reset code from
the platform) and 5e669ec5 (ARM: sunxi: Remove init_machine callback) for
the sun4i, sun5i and sun7i families.

This is needed because the watchdog counterpart of these commits was dropped,
and didn't make it into 3.16. In order to still be able to reboot the board, we
need to reintroduce that code. Of course, the long term view is still to get
rid of that code in mach-sunxi.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v3.16/fixes-against-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Merge OMAP fixes from Tony Lindgren:

Fixes for omaps for issues discovered during the merge window and
enabling of a few features that had to wait for the driver
dependencies to clear.

The fixes included are:

- Fix am43xx hard reset flags
- Fix SoC detection for DRA722
- Fix CPU OPP table for omap5
- Fix legacy mux parser bug if requested muxname is a prefix of
  multiple mux entries
- Fix qspi interrupt binding that relies on the irq crossbar
  that has not yet been enabled
- Add missing phy_sel for am43x-epos-evm
- Drop unused gic_init_irq() that is no longer needed

And the enabling of features that had driver dependencies are:

- Change dra7 to use Audio Tracking Logic clock instead of a fixed
  clock now that the clock driver for it has been merged

- Enable off idle configuration for selected omaps as all the kernel
  dependencies for device tree based booting are finally merged as
  this is needed to get the automated PM tests working finally with
  device tree based booting

- Add hwmod entry for ocp2scp3 for omap5 to get sata working as
  all the driver dependencies are now in the kernel and this patch
  fell through the cracks during the merge window

* tag 'omap-for-v3.16/fixes-against-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: dra7-evm: remove interrupt binding
  ARM: OMAP2+: Fix parser-bug in platform muxing code
  ARM: DTS: dra7/dra7xx-clocks: ATL related changes
  ARM: OMAP2+: drop unused function
  ARM: dts: am43x-epos-evm: Add Missing cpsw-phy-sel for am43x-epos-evm
  ARM: dts: omap5: Update CPU OPP table as per final production Manual
  ARM: DRA722: add detection of SoC information
  ARM: dts: Enable twl4030 off-idle configuration for selected omaps
  ARM: OMAP5: hwmod: Add ocp2scp3 and sata hwmods
  ARM: OMAP2+: hwmod: Change hardreset soc_ops for AM43XX

Pull md bugfixes from Neil Brown:
 "Two minor bugfixes for md in 3.16"

* tag 'md/3.16-fixes' of git://neil.brown.name/md:
  md: flush writes before starting a recovery.
  md: make sure GET_ARRAY_INFO ioctl reports correct "clean" status

Pull sound fixes from Takashi Iwai:
 "This contains a few fixes for HD-audio: yet another Dell headset pin
  quirk, a fixup for Thinkpad T540P, and an improved fix for
  Haswell/Broadwell HDMI clock setup"

* tag 'sound-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - restore BCLK M/N value as per CDCLK for HSW/BDW display HDA controller
  drm/i915: provide interface for audio driver to query cdclk
  ALSA: hda - Add a fixup for Thinkpad T540p
  ALSA: hda - Add another headset pin quirk for some Dell machines

Pull btrfs fixes from Chris Mason:
 "We've queued up a few fixes in my for-linus branch"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: fix crash when starting transaction
  Btrfs: fix btrfs_print_leaf for skinny metadata
  Btrfs: fix race of using total_bytes_pinned
  btrfs: use E2BIG instead of EIO if compression does not help
  btrfs: remove stale comment from btrfs_flush_all_pending_stuffs
  Btrfs: fix use-after-free when cloning a trailing file hole
  btrfs: fix null pointer dereference in btrfs_show_devname when name is null
  btrfs: fix null pointer dereference in clone_fs_devices when name is null
  btrfs: fix nossd and ssd_spread mount option regression
  Btrfs: fix race between balance recovery and root deletion
  Btrfs: atomically set inode->i_flags in btrfs_update_iflags
  btrfs: only unlock block in verify_parent_transid if we locked it
  Btrfs: assert send doesn't attempt to start transactions
  btrfs compression: reuse recently used workspace
  Btrfs: fix crash when mounting raid5 btrfs with missing disks
  btrfs: create sprout should rename fsid on the sysfs as well
  btrfs: dev replace should replace the sysfs entry
  btrfs: dev add should add its sysfs entry
  btrfs: dev delete should remove sysfs entry
  btrfs: rename add_device_membership to btrfs_kobj_add_device

The CurrentEL system register reports the Current Exception Level
of the CPU. It doesn't say anything about the stack handling, and
yet we compare it to PSR_MODE_EL2t and PSR_MODE_EL2h.

It works by chance because PSR_MODE_EL2t happens to match the right
bits, but that's otherwise a very bad idea. Just check for the EL
value instead.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[catalin.marinas@arm.com: fixed arch/arm64/kernel/efi-entry.S]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

The __sync_icache_dcache routine will only flush the dcache for the
first page of a compound page, potentially leading to stale icache
data residing further on in a hugetlb page.

This patch addresses this issue by taking into consideration the
order of the page when flushing the dcache.
Reported-by: Mark Brown <broonie@linaro.org>
Tested-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org> # v3.11+

The define ARM64_64K_PAGES is tested for rather than
CONFIG_ARM64_64K_PAGES. Correct that typo here.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

For HSW/BDW display HD-A controller, hda_set_bclk() is defined to set BCLK
by programming the M/N values as per the core display clock (CDCLK) queried from
i915 display driver.

And the audio driver will also set BCLK in azx_first_init() since the display
driver can turn off the shared power in boot phase if only eDP is connected
and M/N values will be lost and must be reprogrammed.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

For Haswell and Broadwell, if the display power well has been disabled,
the display audio controller divider values EM4 M VALUE and EM5 N VALUE
will have been lost. The CDCLK frequency is required for reprogramming them
to generate 24MHz HD-A link BCLK. So provide a private interface for the
audio driver to query CDCLK.

This is a stopgap solution until a more generic interface between audio
and display drivers has been implemented.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Pull USB bugfixes from Greg KH:
 "Here's a round of USB bugfixes, quirk additions, and new device ids
  for 3.16-rc4.  Nothing major in here at all, just a bunch of tiny
  changes.  All have been in linux-next with no reported issues"

* tag 'usb-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
  usb: chipidea: udc: delete td from req's td list at ep_dequeue
  usb: Kconfig: make EHCI_MSM selectable for QCOM SOCs
  usb-storage/SCSI: Add broken_fua blacklist flag
  usb: musb: dsps: fix the base address for accessing the mode register
  tools: ffs-test: fix header values endianess
  usb: phy: msm: Do not do runtime pm if the phy is not idle
  usb: musb: Ensure that cppi41 timer gets armed on premature DMA TX irq
  usb: gadget: gr_udc: Fix check for invalid number of microframes
  usb: musb: Fix panic upon musb_am335x module removal
  usb: gadget: f_fs: resurect usb_functionfs_descs_head structure
  Revert "tools: ffs-test: convert to new descriptor format fixing compilation error"
  xhci: Fix runtime suspended xhci from blocking system suspend.
  xhci: clear root port wake on bits if controller isn't wake-up capable
  xhci: correct burst count field for isoc transfers on 1.0 xhci hosts
  xhci: Use correct SLOT ID when handling a reset device command
  MAINTAINERS: update e-mail address
  usb: option: add/modify Olivetti Olicard modems
  USB: ftdi_sio: fix null deref at port probe
  MAINTAINERS: drop two usb-serial subdriver entries
  USB: option: add device ID for SpeedUp SU9800 usb 3g modem
  ...

Pull staging driver bugfixes from Greg KH:
 "Nothing major here, just 4 small bugfixes that resolve some issues
  reported for the IIO (staging and non-staging) and the tidspbridge
  driver"

* tag 'staging-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: tidspbridge: fix an erroneous removal of parentheses
  iio: of_iio_channel_get_by_name() returns non-null pointers for error legs
  staging: iio/ad7291: fix error code in ad7291_probe()
  iio:adc:ad799x: Fix reading and writing of event values, apply shift

Merge tag 'driver-core-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core fixes from Greg KH:
 "Well, one drivercore fix for kernfs to resolve a reported issue with
  sysfs files being updated from atomic contexts, and another lz4 bugfix
  for testing potential buffer overflows"

* tag 'driver-core-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  lz4: add overrun checks to lz4_uncompress_unknownoutputsize()
  kernfs: kernfs_notify() must be useable from non-sleepable contexts