- 12 Sep, 2024 18 commits
-
-
Parthiban Veerasooran authored
Implement register write operation according to the control communication specified in the OPEN Alliance 10BASE-T1x MACPHY Serial Interface document. Control write commands are used by the SPI host to write registers within the MAC-PHY. Each control write commands are composed of a 32 bits control command header followed by register write data. The MAC-PHY ignores the final 32 bits of data from the SPI host at the end of the control write command. The write command and data is also echoed from the MAC-PHY back to the SPI host to enable the SPI host to identify which register write failed in the case of any bus errors. Control write commands can write either a single register or multiple consecutive registers. When multiple consecutive registers are written, the address is automatically post-incremented by the MAC-PHY. Writing to any unimplemented or undefined registers shall be ignored and yield no effect. Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com> Link: https://patch.msgid.link/20240909082514.262942-3-Parthiban.Veerasooran@microchip.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Parthiban Veerasooran authored
The IEEE 802.3cg project defines two 10 Mbit/s PHYs operating over a single pair of conductors. The 10BASE-T1L (Clause 146) is a long reach PHY supporting full duplex point-to-point operation over 1 km of single balanced pair of conductors. The 10BASE-T1S (Clause 147) is a short reach PHY supporting full / half duplex point-to-point operation over 15 m of single balanced pair of conductors, or half duplex multidrop bus operation over 25 m of single balanced pair of conductors. Furthermore, the IEEE 802.3cg project defines the new Physical Layer Collision Avoidance (PLCA) Reconciliation Sublayer (Clause 148) meant to provide improved determinism to the CSMA/CD media access method. PLCA works in conjunction with the 10BASE-T1S PHY operating in multidrop mode. The aforementioned PHYs are intended to cover the low-speed / low-cost applications in industrial and automotive environment. The large number of pins (16) required by the MII interface, which is specified by the IEEE 802.3 in Clause 22, is one of the major cost factors that need to be addressed to fulfil this objective. The MAC-PHY solution integrates an IEEE Clause 4 MAC and a 10BASE-T1x PHY exposing a low pin count Serial Peripheral Interface (SPI) to the host microcontroller. This also enables the addition of Ethernet functionality to existing low-end microcontrollers which do not integrate a MAC controller. Reviewed-by:
-
Jakub Kicinski authored
Mina Almasry says: ==================== Device Memory TCP Device memory TCP (devmem TCP) is a proposal for transferring data to and/or from device memory efficiently, without bouncing the data to a host memory buffer. * Problem: A large amount of data transfers have device memory as the source and/or destination. Accelerators drastically increased the volume of such transfers. Some examples include: - ML accelerators transferring large amounts of training data from storage into GPU/TPU memory. In some cases ML training setup time can be as long as 50% of TPU compute time, improving data transfer throughput & efficiency can help improving GPU/TPU utilization. - Distributed training, where ML accelerators, such as GPUs on different hosts, exchange data among them. - Distributed raw block storage applications transfer large amounts of data with remote SSDs, much of this data does not require host processing. Today, the majority of the Device-to-Device data transfers the network are implemented as the following low level operations: Device-to-Host copy, Host-to-Host network transfer, and Host-to-Device copy. The implementation is suboptimal, especially for bulk data transfers, and can put significant strains on system resources, such as host memory bandwidth, PCIe bandwidth, etc. One important reason behind the current state is the kernel’s lack of semantics to express device to network transfers. * Proposal: In this patch series we attempt to optimize this use case by implementing socket APIs that enable the user to: 1. send device memory across the network directly, and 2. receive incoming network packets directly into device memory. Packet _payloads_ go directly from the NIC to device memory for receive and from device memory to NIC for transmit. Packet _headers_ go to/from host memory and are processed by the TCP/IP stack normally. The NIC _must_ support header split to achieve this. Advantages: - Alleviate host memory bandwidth pressure, compared to existing network-transfer + device-copy semantics. - Alleviate PCIe BW pressure, by limiting data transfer to the lowest level of the PCIe tree, compared to traditional path which sends data through the root complex. * Patch overview: ** Part 1: netlink API Gives user ability to bind dma-buf to an RX queue. ** Part 2: scatterlist support Currently the standard for device memory sharing is DMABUF, which doesn't generate struct pages. On the other hand, networking stack (skbs, drivers, and page pool) operate on pages. We have 2 options: 1. Generate struct pages for dmabuf device memory, or, 2. Modify the networking stack to process scatterlist. Approach #1 was attempted in RFC v1. RFC v2 implements approach #2. ** part 3: page pool support We piggy back on page pool memory providers proposal: https://github.com/kuba-moo/linux/tree/pp-providers It allows the page pool to define a memory provider that provides the page allocation and freeing. It helps abstract most of the device memory TCP changes from the driver. ** part 4: support for unreadable skb frags Page pool iovs are not accessible by the host; we implement changes throughput the networking stack to correctly handle skbs with unreadable frags. ** Part 5: recvmsg() APIs We define user APIs for the user to send and receive device memory. Not included with this series is the GVE devmem TCP support, just to simplify the review. Code available here if desired: https://github.com/mina/linux/tree/tcpdevmem This series is built on top of net-next with Jakub's pp-providers changes cherry-picked. * NIC dependencies: 1. (strict) Devmem TCP require the NIC to support header split, i.e. the capability to split incoming packets into a header + payload and to put each into a separate buffer. Devmem TCP works by using device memory for the packet payload, and host memory for the packet headers. 2. (optional) Devmem TCP works better with flow steering support & RSS support, i.e. the NIC's ability to steer flows into certain rx queues. This allows the sysadmin to enable devmem TCP on a subset of the rx queues, and steer devmem TCP traffic onto these queues and non devmem TCP elsewhere. The NIC I have access to with these properties is the GVE with DQO support running in Google Cloud, but any NIC that supports these features would suffice. I may be able to help reviewers bring up devmem TCP on their NICs. * Testing: The series includes a udmabuf kselftest that show a simple use case of devmem TCP and validates the entire data path end to end without a dependency on a specific dmabuf provider. ** Test Setup Kernel: net-next with this series and memory provider API cherry-picked locally. Hardware: Google Cloud A3 VMs. NIC: GVE with header split & RSS & flow steering support. ==================== Link: https://patch.msgid.link/20240910171458.219195-1-almasrymina@google.comSigned-off-by:
-
Mina Almasry authored
Add dmabuf information to page_pool stats: $ ./cli.py --spec ../netlink/specs/netdev.yaml --dump page-pool-get ... {'dmabuf': 10, 'id': 456, 'ifindex': 3, 'inflight': 1023, 'inflight-mem': 4190208}, {'dmabuf': 10, 'id': 455, 'ifindex': 3, 'inflight': 1023, 'inflight-mem': 4190208}, {'dmabuf': 10, 'id': 454, 'ifindex': 3, 'inflight': 1023, 'inflight-mem': 4190208}, {'dmabuf': 10, 'id': 453, 'ifindex': 3, 'inflight': 1023, 'inflight-mem': 4190208}, {'dmabuf': 10, 'id': 452, 'ifindex': 3, 'inflight': 1023, 'inflight-mem': 4190208}, {'dmabuf': 10, 'id': 451, 'ifindex': 3, 'inflight': 1023, 'inflight-mem': 4190208}, {'dmabuf': 10, 'id': 450, 'ifindex': 3, 'inflight': 1023, 'inflight-mem': 4190208}, {'dmabuf': 10, 'id': 449, 'ifindex': 3, 'inflight': 1023, 'inflight-mem': 4190208}, And queue stats: $ ./cli.py --spec ../netlink/specs/netdev.yaml --dump queue-get ... {'dmabuf': 10, 'id': 8, 'ifindex': 3, 'type': 'rx'}, {'dmabuf': 10, 'id': 9, 'ifindex': 3, 'type': 'rx'}, {'dmabuf': 10, 'id': 10, 'ifindex': 3, 'type': 'rx'}, {'dmabuf': 10, 'id': 11, 'ifindex': 3, 'type': 'rx'}, {'dmabuf': 10, 'id': 12, 'ifindex': 3, 'type': 'rx'}, {'dmabuf': 10, 'id': 13, 'ifindex': 3, 'type': 'rx'}, {'dmabuf': 10, 'id': 14, 'ifindex': 3, 'type': 'rx'}, {'dmabuf': 10, 'id': 15, 'ifindex': 3, 'type': 'rx'}, Suggested-by:Mina Almasry <almasrymina@google.com> Reviewed-by:
-
Mina Almasry authored
ncdevmem is a devmem TCP netcat. It works similarly to netcat, but it sends and receives data using the devmem TCP APIs. It uses udmabuf as the dmabuf provider. It is compatible with a regular netcat running on a peer, or a ncdevmem running on a peer. In addition to normal netcat support, ncdevmem has a validation mode, where it sends a specific pattern and validates this pattern on the receiver side to ensure data integrity. Suggested-by:
Stanislav Fomichev <sdf@fomichev.me> Signed-off-by:
-
Mina Almasry authored
Add documentation outlining the usage and details of devmem TCP. Signed-off-by:
Bagas Sanjaya <bagasdotme@gmail.com> Reviewed-by:
Donald Hunter <donald.hunter@gmail.com> Link: https://patch.msgid.link/20240910171458.219195-12-almasrymina@google.comSigned-off-by:
-
Mina Almasry authored
Add an interface for the user to notify the kernel that it is done reading the devmem dmabuf frags returned as cmsg. The kernel will drop the reference on the frags to make them available for reuse. Signed-off-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
Kaiyuan Zhang <kaiyuanz@google.com> Signed-off-by:
Pavel Begunkov <asml.silence@gmail.com> Reviewed-by:
Eric Dumazet <edumazet@google.com> Link: https://patch.msgid.link/20240910171458.219195-11-almasrymina@google.comSigned-off-by:
-
Mina Almasry authored
In tcp_recvmsg_locked(), detect if the skb being received by the user is a devmem skb. In this case - if the user provided the MSG_SOCK_DEVMEM flag - pass it to tcp_recvmsg_devmem() for custom handling. tcp_recvmsg_devmem() copies any data in the skb header to the linear buffer, and returns a cmsg to the user indicating the number of bytes returned in the linear buffer. tcp_recvmsg_devmem() then loops over the unaccessible devmem skb frags, and returns to the user a cmsg_devmem indicating the location of the data in the dmabuf device memory. cmsg_devmem contains this information: 1. the offset into the dmabuf where the payload starts. 'frag_offset'. 2. the size of the frag. 'frag_size'. 3. an opaque token 'frag_token' to return to the kernel when the buffer is to be released. The pages awaiting freeing are stored in the newly added sk->sk_user_frags, and each page passed to userspace is get_page()'d. This reference is dropped once the userspace indicates that it is done reading this page. All pages are released when the socket is destroyed. Signed-off-by:
-
Mina Almasry authored
For device memory TCP, we expect the skb headers to be available in host memory for access, and we expect the skb frags to be in device memory and unaccessible to the host. We expect there to be no mixing and matching of device memory frags (unaccessible) with host memory frags (accessible) in the same skb. Add a skb->devmem flag which indicates whether the frags in this skb are device memory frags or not. __skb_fill_netmem_desc() now checks frags added to skbs for net_iov, and marks the skb as skb->devmem accordingly. Add checks through the network stack to avoid accessing the frags of devmem skbs and avoid coalescing devmem skbs with non devmem skbs. Signed-off-by:
-
Mina Almasry authored
Make skb_frag_page() fail in the case where the frag is not backed by a page, and fix its relevant callers to handle this case. Signed-off-by:
-
Mina Almasry authored
Implement a memory provider that allocates dmabuf devmem in the form of net_iov. The provider receives a reference to the struct netdev_dmabuf_binding via the pool->mp_priv pointer. The driver needs to set this pointer for the provider in the net_iov. The provider obtains a reference on the netdev_dmabuf_binding which guarantees the binding and the underlying mapping remains alive until the provider is destroyed. Usage of PP_FLAG_DMA_MAP is required for this memory provide such that the page_pool can provide the driver with the dma-addrs of the devmem. Support for PP_FLAG_DMA_SYNC_DEV is omitted for simplicity & p.order != 0. Signed-off-by:
-
Mina Almasry authored
Convert netmem to be a union of struct page and struct netmem. Overload the LSB of struct netmem* to indicate that it's a net_iov, otherwise it's a page. Currently these entries in struct page are rented by the page_pool and used exclusively by the net stack: struct { unsigned long pp_magic; struct page_pool *pp; unsigned long _pp_mapping_pad; unsigned long dma_addr; atomic_long_t pp_ref_count; }; Mirror these (and only these) entries into struct net_iov and implement netmem helpers that can access these common fields regardless of whether the underlying type is page or net_iov. Implement checks for net_iov in netmem helpers which delegate to mm APIs, to ensure net_iov are never passed to the mm stack. Signed-off-by: -
Mina Almasry authored
Implement netdev devmem allocator. The allocator takes a given struct netdev_dmabuf_binding as input and allocates net_iov from that binding. The allocation simply delegates to the binding's genpool for the allocation logic and wraps the returned memory region in a net_iov struct. Signed-off-by:
-
Mina Almasry authored
Add a netdev_dmabuf_binding struct which represents the dma-buf-to-netdevice binding. The netlink API will bind the dma-buf to rx queues on the netdevice. On the binding, the dma_buf_attach & dma_buf_map_attachment will occur. The entries in the sg_table from mapping will be inserted into a genpool to make it ready for allocation. The chunks in the genpool are owned by a dmabuf_chunk_owner struct which holds the dma-buf offset of the base of the chunk and the dma_addr of the chunk. Both are needed to use allocations that come from this chunk. We create a new type that represents an allocation from the genpool: net_iov. We setup the net_iov allocation size in the genpool to PAGE_SIZE for simplicity: to match the PAGE_SIZE normally allocated by the page pool and given to the drivers. The user can unbind the dmabuf from the netdevice by closing the netlink socket that established the binding. We do this so that the binding is automatically unbound even if the userspace process crashes. The binding and unbinding leaves an indicator in struct netdev_rx_queue that the given queue is bound, and the binding is actuated by resetting the rx queue using the queue API. The netdev_dmabuf_binding struct is refcounted, and releases its resources only when all the refs are released. Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by:
-
Mina Almasry authored
API takes the dma-buf fd as input, and binds it to the netdevice. The user can specify the rx queues to bind the dma-buf to. Suggested-by:
-
Mina Almasry authored
Add netdev_rx_queue_restart(), which resets an rx queue using the queue API recently merged[1]. The queue API was merged to enable the core net stack to reset individual rx queues to actuate changes in the rx queue's configuration. In later patches in this series, we will use netdev_rx_queue_restart() to reset rx queues after binding or unbinding dmabuf configuration, which will cause reallocation of the page_pool to repopulate its memory using the new configuration. [1] https://lore.kernel.org/netdev/20240430231420.699177-1-shailend@google.com/T/Signed-off-by:
David Wei <dw@davidwei.uk> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queueJakub Kicinski authored
Tony Nguyen says: ==================== idpf: XDP chapter II: convert Tx completion to libeth Alexander Lobakin says: XDP for idpf is currently 5 chapters: * convert Rx to libeth; * convert Tx completion to libeth (this); * generic XDP and XSk code changes; * actual XDP for idpf via libeth_xdp; * XSk for idpf (^). Part II does the following: * adds generic libeth Tx completion routines; * converts idpf to use generic libeth Tx comp routines; * fixes Tx queue timeouts and robustifies Tx completion in general; * fixes Tx event/descriptor flushes (writebacks). Most idpf patches again remove more lines than adds. Generic Tx completion helpers and structs are needed as libeth_xdp (Ch. III) makes use of them. WB_ON_ITR is needed since XDPSQs don't want to work without it at all. Tx queue timeouts fixes are needed since without them, it's way easier to catch a Tx timeout event when WB_ON_ITR is enabled. * '200GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue: idpf: enable WB_ON_ITR idpf: fix netdev Tx queue stop/wake idpf: refactor Tx completion routines netdevice: add netdev_tx_reset_subqueue() shorthand idpf: convert to libeth Tx buffer completion libeth: add Tx buffer completion helpers ==================== Link: https://patch.msgid.link/20240909205323.3110312-1-anthony.l.nguyen@intel.comSigned-off-by:
-
Divya Koppera authored
Add support for cable diagnostics in lan887x PHY. Using this we can diagnose connected/open/short wires and also length where cable fault is occurred. Signed-off-by:
Divya Koppera <divya.koppera@microchip.com> Reviewed-by:
-
- 11 Sep, 2024 22 commits
-
-
Maxime Chevallier authored
When processing the netlink GET requests to get PHY info, the req_info.pdn pointer is NULL when no PHY matches the requested parameters, such as when the phy_index is invalid, or there's simply no PHY attached to the interface. Therefore, check the req_info.pdn pointer for NULL instead of dereferencing it. Suggested-by:
Maxime Chevallier <maxime.chevallier@bootlin.com> Reviewed-by:
-
Rosen Penev authored
If nvmem loads after the ethernet driver, mac address assignments will not take effect. of_get_ethdev_address returns EPROBE_DEFER in such a case so we need to handle that to avoid eth_hw_addr_random. Signed-off-by:
Rosen Penev <rosenp@gmail.com> Reviewed-by:
Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20240910220913.14101-1-rosenp@gmail.comSigned-off-by:
-
Jonathan Cooper authored
Add X4 series. Most functionality is the same as previous EF10 nics but enough is different to warrant a new nic type struct and revision; for example legacy interrupts and SRIOV are not supported. Most removed features will be re-added later as new implementations. Signed-off-by:
Jonathan Cooper <jonathan.s.cooper@amd.com> Acked-by:
Edward Cree <ecree.xilinx@gmail.com> Acked-by:
Martin Habets <habetsm.xilinx@gmail.com> Link: https://patch.msgid.link/20240910153014.12803-1-jonathan.s.cooper@amd.comSigned-off-by:
-
Colin Ian King authored
Don't populate the const read-only array key on the stack at run time, instead make it static. Signed-off-by:
Colin Ian King <colin.i.king@gmail.com> Reviewed-by:
-
Jakub Kicinski authored
Matthieu Baerts says: ==================== mptcp: fallback to TCP after 3 MPC drop + cache The SYN + MPTCP_CAPABLE packets could be explicitly dropped by firewalls somewhere in the network, e.g. if they decide to drop packets based on the TCP options, instead of stripping them off. The idea of this series is to fallback to TCP after 3 SYN+MPC drop (patch 2). If the connection succeeds after the fallback, it very likely means a blackhole has been detected. In this case (patch 3), MPTCP can be disabled for a certain period of time, 1h by default. If after this period, MPTCP is still blocked, the period is doubled. This technique is inspired by the one used by TCP FastOpen. This should help applications which want to use MPTCP by default on the client side if available. ==================== Link: https://patch.msgid.link/20240909-net-next-mptcp-fallback-x-mpc-v1-0-da7ebb4cd2a3@kernel.orgSigned-off-by:
-
Matthieu Baerts (NGI0) authored
An MPTCP firewall blackhole can be detected if the following SYN retransmission after a fallback to "plain" TCP is accepted. In case of blackhole, a similar technique to the one in place with TFO is now used: MPTCP can be disabled for a certain period of time, 1h by default. This time period will grow exponentially when more blackhole issues get detected right after MPTCP is re-enabled and will reset to the initial value when the blackhole issue goes away. The blackhole period can be modified thanks to a new sysctl knob: blackhole_timeout. Two new MIB counters help understanding what's happening: - 'Blackhole', incremented when a blackhole is detected. - 'MPCapableSYNTXDisabled', incremented when an MPTCP connection directly falls back to TCP during the blackhole period. Because the technique is inspired by the one used by TFO, an important part of the new code is similar to what can find in tcp_fastopen.c, with some adaptations to the MPTCP case. Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/57Signed-off-by:
Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://patch.msgid.link/20240909-net-next-mptcp-fallback-x-mpc-v1-3-da7ebb4cd2a3@kernel.orgSigned-off-by:
-
Matthieu Baerts (NGI0) authored
Some middleboxes might be nasty with MPTCP, and decide to drop packets with MPTCP options, instead of just dropping the MPTCP options (or letting them pass...). In this case, it sounds better to fallback to "plain" TCP after 2 retransmissions, and try again. Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/477Signed-off-by:
-
Matthieu Baerts (NGI0) authored
This helper will be used outside protocol.h in the following commit. While at it, also add a 'pr_fallback()' debug print, to help identifying fallbacks. Signed-off-by:
-
Jakub Kicinski authored
Sebastian Andrzej Siewior says: ==================== net: hsr: Use the seqnr lock for frames received via interlink port. This is follow-up to the thread at https://lore.kernel.org/all/20240904133725.1073963-1-edumazet@google.com/ ==================== Link: https://patch.msgid.link/20240906132816.657485-1-bigeasy@linutronix.deSigned-off-by:
-
Eric Dumazet authored
Remove interlink_sequence_nr which is unused. [ bigeasy: split out from Eric's patch ]. Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Link: https://patch.msgid.link/20240906132816.657485-3-bigeasy@linutronix.deSigned-off-by:
-
Sebastian Andrzej Siewior authored
syzbot reported that the seqnr_lock is not acquire for frames received over the interlink port. In the interlink case a new seqnr is generated and assigned to the frame. Frames, which are received over the slave port have already a sequence number assigned so the lock is not required. Acquire the hsr_priv::seqnr_lock during in the invocation of hsr_forward_skb() if a packet has been received from the interlink port. Reported-by: syzbot+3d602af7549af539274e@syzkaller.appspotmail.com Closes: https://groups.google.com/g/syzkaller-bugs/c/KppVvGviGg4/m/EItSdCZdBAAJ Fixes: 5055cccf ("net: hsr: Provide RedBox support (HSR-SAN)") Signed-off-by:
Lukasz Majewski <lukma@denx.de> Tested-by:
-
Jakub Kicinski authored
Merge tag 'wireless-next-2024-09-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next Kalle Valo says: ==================== wireless-next patches for v6.12 The last -next "new features" pull request for v6.12. The stack now supports DFS on MLO but otherwise nothing really standing out. Major changes: cfg80211/mac80211 * EHT rate support in AQL airtime * DFS support for MLO rtw89 * complete BT-coexistence code for RTL8852BT * RTL8922A WoWLAN net-detect support * tag 'wireless-next-2024-09-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (105 commits) wifi: brcmfmac: cfg80211: Convert comma to semicolon wifi: rsi: Remove an unused field in struct rsi_debugfs wifi: libertas: Cleanup unused declarations wifi: wilc1000: Convert using devm_clk_get_optional_enabled() in wilc_bus_probe() wifi: wilc1000: Convert using devm_clk_get_optional_enabled() in wilc_sdio_probe() wifi: wilc1000: fix potential RCU dereference issue in wilc_parse_join_bss_param wifi: mwifiex: Fix memcpy() field-spanning write warning in mwifiex_cmd_802_11_scan_ext() wifi: mac80211: use two-phase skb reclamation in ieee80211_do_stop() wifi: cfg80211: fix two more possible UBSAN-detected off-by-one errors wifi: cfg80211: fix kernel-doc for per-link data wifi: mt76: mt7925: replace chan config with extend txpower config for clc wifi: mt76: mt7925: fix a potential array-index-out-of-bounds issue for clc wifi: mt76: mt7615: check devm_kasprintf() returned value wifi: mt76: mt7925: convert comma to semicolon wifi: mt76: mt7925: fix a potential association failure upon resuming wifi: mt76: Avoid multiple -Wflex-array-member-not-at-end warnings wifi: mt76: mt7921: Check devm_kasprintf() returned value wifi: mt76: mt7915: check devm_kasprintf() returned value wifi: mt76: mt7915: avoid long MCU command timeouts during SER wifi: mt76: mt7996: fix uninitialized TLV data ... ==================== Link: https://patch.msgid.link/20240911084147.A205DC4AF0F@smtp.kernel.orgSigned-off-by:
-
David S. Miller authored
Raju Lakkaraju says: ==================== Add support to PHYLINK for LAN743x/PCI11x1x chips This is the follow-up patch series of https://lkml.iu.edu/hypermail/linux/kernel/2310.2/02078.html Divide the PHYLINK adaptation and SFP modifications into two separate patch series. The current patch series focuses on transitioning the LAN743x driver's PHY support from phylib to phylink. Tested on PCI11010 Rev-1 Evaluation board Change List: ============ V5 -> V6: - Remove the lan743x_find_max_speed( ) function. Not require - Add EEE enable check before calling lan743x_mac_eee_enable( ) function V4 -> V5: - Remove the fixed_phy_unregister( ) function. Not require - Remove the "phydev->eee_enabled" check to update the MAC EEE enable/disable - Call lan743x_mac_eee_enable() with true after update tx_lpi_timer. - Add phy_support_eee() to initialize the EEE flags V3 -> V4: - Add fixed-link patch along with this series. Note: Note: This code was developed by Mr.Russell King Ref: https://lore.kernel.org/netdev/LV8PR11MB8700C786F5F1C274C73036CC9F8E2@LV8PR11MB8700.namprd11.prod.outlook.com/T/#me943adf54f1ea082edf294aba448fa003a116815 - Change phylink fixed-link function header's string from "Returns" to "Returns:" - Remove the EEE private variable from LAN743x adapter strcture and fix the EEE's set/get functions - set the individual caps (i.e. _RGMII, _RGMII_ID, _RGMII_RXID and __RGMII_TXID) replace with phy_interface_set_rgmii( ) function - Change lan743x_set_eee( ) to lan743x_mac_eee_enable( ) V2 -> V3: - Remove the unwanted parens in each of these if() sub-blocks - Replace "to_net_dev(config->dev)" with "netdev". - Add GMII_ID/RGMII_TXID/RGMII_RXID in supported_interfaces - Fix the lan743x_phy_handle_exists( ) return type V1 -> V2: - Fix the Russell King's comments i.e. remove the speed, duplex update in lan743x_phylink_mac_config( ) - pre-March 2020 legacy support has been removed V0 -> V1: - Integrate with Synopsys DesignWare XPCS drivers - Based on external review comments, - Changes made to SGMII interface support only 1G/100M/10M bps speed - Changes made to 2500Base-X interface support only 2.5Gbps speed - Add check for not is_sgmii_en with is_sfp_support_en support - Change the "pci11x1x_strap_get_status" function return type from void to int - Add ethtool phylink wol, eee, pause get/set functions ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Raju Lakkaraju authored
Add support to ethtool phylink functions: - get/set settings like speed, duplex etc - get/set the wake-on-lan (WOL) - get/set the energy-efficient ethernet (EEE) - get/set the pause Reviewed-by:
Raju Lakkaraju <Raju.Lakkaraju@microchip.com> Signed-off-by:
-
Raju Lakkaraju authored
Migrate phy support from phylib to phylink. Reviewed-by:
-
Raju Lakkaraju authored
Create separate Link Speed Duplex (LSD) update state function from lan743x_sgmii_config () to use as subroutine. Reviewed-by:
-
Raju Lakkaraju authored
Create separate PCS power reset function from lan743x_sgmii_config () to use as subroutine. Reviewed-by:
-
Russell King authored
The function allows for the configuration of a fixed link state for a given phylink instance. This addition is particularly useful for network devices that operate with a fixed link configuration, where the link parameters do not change dynamically. By using `phylink_set_fixed_link()`, drivers can easily set up the fixed link state during initialization or configuration changes. Reviewed-by:
Russell King <linux@armlinux.org.uk> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queueJakub Kicinski authored
Tony Nguyen says: ==================== ice: support devlink subfunction Michal Swiatkowski says: Currently ice driver does not allow creating more than one networking device per physical function. The only way to have more hardware backed netdev is to use SR-IOV. Following patchset adds support for devlink port API. For each new pcisf type port, driver allocates new VSI, configures all resources needed, including dynamically MSIX vectors, program rules and registers new netdev. This series supports only one Tx/Rx queue pair per subfunction. Example commands: devlink port add pci/0000:31:00.1 flavour pcisf pfnum 1 sfnum 1000 devlink port function set pci/0000:31:00.1/1 hw_addr 00:00:00:00:03:14 devlink port function set pci/0000:31:00.1/1 state active devlink port function del pci/0000:31:00.1/1 Make the port representor and eswitch code generic to support subfunction representor type. VSI configuration is slightly different between VF and SF. It needs to be reflected in the code. * '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue: ice: subfunction activation and base devlink ops ice: basic support for VLAN in subfunctions ice: support subfunction devlink Tx topology ice: implement netdevice ops for SF representor ice: check if SF is ready in ethtool ops ice: don't set target VSI for subfunction ice: create port representor for SF ice: make representor code generic ice: implement netdev for subfunction ice: base subfunction aux driver ice: allocate devlink for subfunction ice: treat subfunction VSI the same as PF VSI ice: add basic devlink subfunctions support ice: export ice ndo_ops functions ice: add new VSI type for subfunctions ==================== Link: https://patch.msgid.link/20240906223010.2194591-1-anthony.l.nguyen@intel.comSigned-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linuxJakub Kicinski authored
Saeed Mahameed says: ==================== mlx5-updates-2024-08-29 HW-Managed Flow Steering in mlx5 driver Yevgeny Kliteynik says: ======================= 1. Overview ----------- ConnectX devices support packet matching, modification, and redirection. This functionality is referred as Flow Steering. To configure a steering rule, the rule is written to the device-owned memory. This memory is accessed and cached by the device when processing a packet. The first implementation of Flow Steering was done in FW, and it is referred in the mlx5 driver as Device-Managed Flow Steering (DMFS). Later we introduced SW-managed Flow Steering (SWS or SMFS), where the driver is writing directly to the device's configuration memory (ICM) through RC QP using RDMA operations (RDMA-read and RDAM-write), thus achieving higher rates of rule insertion/deletion. Now we introduce a new flow steering implementation: HW-Managed Flow Steering (HWS or HMFS). In this new approach, the driver is configuring steering rules directly to the HW using the WQs with a special new type of WQE. This way we can reach higher rule insertion/deletion rate with much lower CPU utilization compared to SWS. The key benefits of HWS as opposed to SWS: + HW manages the steering decision tree - HW calculates CRC for each entry - HW handles tree hash collisions - HW & FW manage objects refcount + HW keeps cache coherency: - HW provides tree access locking and synchronization - HW provides notification on completion + Insertion rate isn’t affected by background traffic - Dedicated HW components that handle insertion 2. Performance -------------- Measuring Connection Tracking with simple IPv4 flows w/o NAT, we are able to get ~5 times more flows offloaded per second using HWS. 3. Configuration ---------------- The enablement of HWS mode in eswitch manager is done using the same devlink param that is already used for switching between FW-managed steering and SW-managed steering modes: # devlink dev param set pci/<PCI_ID> name flow_steering_mode cmod runtime value hmfs 4. Upstream Submission ---------------------- HWS support consists of 3 main components: + Steering: - The lower layer that exposes HWS API to upper layers and implements all the management of flow steering building blocks + FS-Core - Implementation of fs_hws layer to enable fs_core to use HWS instead of FW or SW steering - Create HW steering action pools to utilize the ability of HWS to share steering actions among different rules - Add support for configuring HWS mode through devlink command, similar to configuring SWS mode + Connection Tracking - Implementation of CT support for HW steering - Hooks up the CT ops for the new steering mode and uses the HWS API to implement connection tracking. Because of the large number of patches, we need to perform the submission in several separate patch series. This series is the first submission that lays the ground work for the next submissions, where an actual user of HWS will be added. 5. Patches in this series ------------------------- This patch series contains implementation of the first bullet from above. ======================= * tag 'mlx5-updates-2024-09-02' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux: net/mlx5: HWS, added API and enabled HWS support net/mlx5: HWS, added send engine and context handling net/mlx5: HWS, added debug dump and internal headers net/mlx5: HWS, added backward-compatible API handling net/mlx5: HWS, added memory management handling net/mlx5: HWS, added vport handling net/mlx5: HWS, added modify header pattern and args handling net/mlx5: HWS, added FW commands handling net/mlx5: HWS, added matchers functionality net/mlx5: HWS, added definers handling net/mlx5: HWS, added rules handling net/mlx5: HWS, added tables handling net/mlx5: HWS, added actions handling net/mlx5: Added missing definitions in preparation for HW Steering net/mlx5: Added missing mlx5_ifc definition for HW Steering ==================== Link: https://patch.msgid.link/20240909181250.41596-1-saeed@kernel.orgSigned-off-by: -
Jakub Kicinski authored
Merge tag 'ipsec-next-2024-09-10' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next Steffen Klassert says: ==================== pull request (net-next): ipsec-next 2024-09-10 1) Remove an unneeded WARN_ON on packet offload. From Patrisious Haddad. 2) Add a copy from skb_seq_state to buffer function. This is needed for the upcomming IPTFS patchset. From Christian Hopps. 3) Spelling fix in xfrm.h. From Simon Horman. 4) Speed up xfrm policy insertions. From Florian Westphal. 5) Add and revert a patch to support xfrm interfaces for packet offload. This patch was just half cooked. 6) Extend usage of the new xfrm_policy_is_dead_or_sk helper. From Florian Westphal. 7) Update comments on sdb and xfrm_policy. From Florian Westphal. 8) Fix a null pointer dereference in the new policy insertion code From Florian Westphal. 9) Fix an uninitialized variable in the new policy insertion code. From Nathan Chancellor. * tag 'ipsec-next-2024-09-10' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next: xfrm: policy: Restore dir assignments in xfrm_hash_rebuild() xfrm: policy: fix null dereference Revert "xfrm: add SA information to the offloaded packet" xfrm: minor update to sdb and xfrm_policy comments xfrm: policy: use recently added helper in more places xfrm: add SA information to the offloaded packet xfrm: policy: remove remaining use of inexact list xfrm: switch migrate to xfrm_policy_lookup_bytype xfrm: policy: don't iterate inexact policies twice at insert time selftests: add xfrm policy insertion speed test script xfrm: Correct spelling in xfrm.h net: add copy from skb_seq_state to buffer function xfrm: Remove documentation WARN_ON to limit return values for offloaded SA ==================== Link: https://patch.msgid.link/20240910065507.2436394-1-steffen.klassert@secunet.comSigned-off-by:
-
Jakub Kicinski authored
Michael Chan says: ==================== bnxt_en: MSIX improvements This patchset makes some improvements related to MSIX. The first patch adjusts the default MSIX vectors assigned for RoCE. On the PF, the number of MSIX is increased to 64 from the current 9. The second patch allocates additional MSIX vectors ahead of time when changing ethtool channels if dynamic MSIX is supported. The 3rd patch makes sure that the IRQ name is not truncated. ==================== Link: https://patch.msgid.link/20240909202737.93852-1-michael.chan@broadcom.comSigned-off-by:
-
