This patch adds the function for configuring the 100/10Mbps speed
selection for the ksz switches. KSZ8795 switch uses Global control 4
register 0x06 bit 4 for choosing 100/10Mpbs. Other switches uses xMII
control 1 0xN300 for it.
For KSZ8795, if the bit is set then 10Mbps is chosen and if bit is
clear then 100Mbps chosen. For all other switches it is other way
around, if the bit is set then 100Mbps is chosen.
So, this patch add the generic function for ksz switch to select the
100/10Mbps speed selection. While configuring, first it disables the
gigabit functionality and then configure the respective speed.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch add helper function for setting and getting the gigabit
enable for the ksz series switch. KSZ8795 switch has different register
address compared to all other ksz switches. KSZ8795 series uses the Port
5 Interface control 6 Bit 6 for configuring the 1Gbps or 100/10Mbps
speed selection. All other switches uses the xMII control 1 0xN301
register Bit6 for gigabit.
Further, for KSZ8795 & KSZ9893 switches if bit 1 then 1Gbps is chosen
and if bit 0 then 100/10Mbps is chosen. It is other way around for
other switches bit 0 is for 1Gbps. So, this patch implements the common
function for configuring the gigabit set and get capability.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace 'the the' with 'the' in the comment.
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Link: https://lore.kernel.org/r/20220725020124.5760-1-slark_xiao@163.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

One rcu_read_unlock() should have been removed in blamed commit.

Fixes: 9b1c21d8 ("ip6mr: do not acquire mrt_lock while calling ip6_mr_forward()")
Reported-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220725200554.2563581-1-eric.dumazet@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Jakub Kicinski says:

====================
tls: rx: decrypt from the TCP queue

This is the final part of my TLS Rx rework. It switches from
strparser to decrypting data from skbs queued in TCP. We don't
need the full strparser for TLS, its needs are very basic.
This set gives us a small but measurable (6%) performance
improvement (continuous stream).
====================

Link: https://lore.kernel.org/r/20220722235033.2594446-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

TLS is a relatively poor fit for strparser. We pause the input
every time a message is received, wait for a read which will
decrypt the message, start the parser, repeat. strparser is
built to delineate the messages, wrap them in individual skbs
and let them float off into the stack or a different socket.
TLS wants the data pages and nothing else. There's no need
for TLS to keep cloning (and occasionally skb_unclone()'ing)
the TCP rx queue.

This patch uses a pre-allocated skb and attaches the skbs
from the TCP rx queue to it as frags. TLS is careful never
to modify the input skb without CoW'ing / detaching it first.

Since we call TCP rx queue cleanup directly we also get back
the benefit of skb deferred free.

Overall this results in a 6% gain in my benchmarks.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Wrap the remaining skb_cow_data() into a helper, so it's easier
to replace down the lane. The new version will change the skb
so make sure relevant pointers get reloaded after the call.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Expose TCP rx queue accessor and cleanup, so that TLS can
decrypt directly from the TCP queue. The expectation
is that the caller can access the skb returned from
tcp_recv_skb() and up to inq bytes worth of data (some
of which may be in ->next skbs) and then call
tcp_read_done() when data has been consumed.
The socket lock must be held continuously across
those two operations.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The non-zero-copy path assumes a full skb with decrypted contents.
This means the device offload would have to CoW the data. Try
to keep the zero-copy status instead, copy the data to user space.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In the future we'll want to reuse the input skb in case of
zero-copy so we shouldn't always free darg.skb. Move the
freeing of darg.skb into the non-zc cases. All cases will
now free ctx->recv_pkt (inside let tls_rx_rec_done()).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

After recent changes the SW side of tls_rx_one_record() can
be nicely encapsulated in its own function. Move the pad handling
as well. This will be useful for ->zc handling in tls_decrypt_device().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

To allow for the logic to change later wrap accesses
which interrogate the input skb in helper functions.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Jiri Pirko says:

====================
Implement dev info and dev flash for line cards

This patchset implements two features:
1) "devlink dev info" is exposed for line card (patches 6-9)
2) "devlink dev flash" is implemented for line card gearbox
   flashing (patch 10)

For every line card, "a nested" auxiliary device is created which
allows to bind the features mentioned above (patch 4).

The relationship between line card and its auxiliary dev devlink
is carried over extra line card netlink attribute (patches 3 and 5).

The first patch removes devlink_mutex from devlink_register/unregister()
which eliminates possible deadlock during devlink reload command. The
second patchset follows up with putting net pointer check into new
helper.

Examples:

$ devlink lc show pci/0000:01:00.0 lc 1
pci/0000:01:00.0:
  lc 1 state active type 16x100G nested_devlink auxiliary/mlxsw_core.lc.0
    supported_types:
       16x100G

$ devlink dev show auxiliary/mlxsw_core.lc.0
auxiliary/mlxsw_core.lc.0

$ devlink dev info auxiliary/mlxsw_core.lc.0
auxiliary/mlxsw_core.lc.0:
  versions:
      fixed:
        hw.revision 0
        fw.psid MT_0000000749
      running:
        ini.version 4
        fw 19.2010.1312

$ devlink dev flash auxiliary/mlxsw_core.lc.0 file mellanox/fw-AGB-rel-19_2010_1312-022-EVB.mfa2
====================

Link: https://lore.kernel.org/r/20220725082925.366455-1-jiri@resnulli.usSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Once line card is activated, check the FW version and PSID are exposed.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Once line card is provisioned, check if HW revision and INI version
are exposed on associated nested auxiliary device.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Implement flash_update() devlink op for the line card devlink instance
to allow user to update line card gearbox FW using MDDT register
and mlxfw.

Example:
$ devlink dev flash auxiliary/mlxsw_core.lc.0 file mellanox/fw-AGB-rel-19_2010_1312-022-EVB.mfa2
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Use tunneled MGIR to obtain PSID of line card device and extend
device_info_get() op to fill up the info with that.

Example:

$ devlink dev info auxiliary/mlxsw_core.lc.0
auxiliary/mlxsw_core.lc.0:
  versions:
      fixed:
        hw.revision 0
        fw.psid MT_0000000749
      running:
        ini.version 4
        fw 19.2010.1312
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The MDDT register allows to deliver query and request messages (PRM
registers, commands) to a DownStream device.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In case the line card is active, go over all possible existing
devices (gearboxes) on it and expose FW version of the flashable one.

Example:

$ devlink dev info auxiliary/mlxsw_core.lc.0
auxiliary/mlxsw_core.lc.0:
  versions:
      fixed:
        hw.revision 0
      running:
        ini.version 4
        fw 19.2010.1312
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Extend existing MDDQ register by possibility to query information about
devices residing on a line card.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Implement info_get() to expose HW revision of a linecard and loaded INI
version.

Example:

$ devlink dev info auxiliary/mlxsw_core.lc.0
auxiliary/mlxsw_core.lc.0:
  versions:
      fixed:
        hw.revision 0
      running:
        ini.version 4
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In order to be eventually able to expose line card gearbox version and
possibility to flash FW, model the line card as a separate device on
auxiliary bus.

Add the auxiliary device for provisioned line card in order to be able
to expose provisioned line card info over devlink dev info. When the
line card becomes active, there may be other additional info added to
the output.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

For the purpose of exposing device info and allow flash update which is
going to be implemented in follow-up patches, introduce a possibility
for a line card to expose relation to nested devlink entity. The nested
devlink entity represents the line card.

Example:

$ devlink lc show pci/0000:01:00.0 lc 1
pci/0000:01:00.0:
  lc 1 state active type 16x100G nested_devlink auxiliary/mlxsw_core.lc.0
    supported_types:
       16x100G
$ devlink dev show auxiliary/mlxsw_core.lc.0
auxiliary/mlxsw_core.lc.0
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Benefit from having devlinks iterator helper
devlinks_xa_for_each_registered_get() and move the net pointer
check inside.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Remove dependency on devlink_mutex during devlinks xarray iteration.

The reason is that devlink_register/unregister() functions taking
devlink_mutex would deadlock during devlink reload operation of devlink
instance which registers/unregisters nested devlink instances.

The devlinks xarray consistency is ensured internally by xarray.
There is a reference taken when working with devlink using
devlink_try_get(). But there is no guarantee that devlink pointer
picked during xarray iteration is not freed before devlink_try_get()
is called.

Make sure that devlink_try_get() works with valid pointer.
Achieve it by:
1) Splitting devlink_put() so the completion is sent only
   after grace period. Completion unblocks the devlink_unregister()
   routine, which is followed-up by devlink_free()
2) During devlinks xa_array iteration, get devlink pointer from xa_array
   holding RCU read lock and taking reference using devlink_try_get()
   before unlock.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Subbaraya Sundeep says:

====================
Octeontx2 minor tc fixes

This patch set fixes two problems found in tc code
wrt to ratelimiting and when installing UDP/TCP filters.

Patch 1: CN10K has different register format compared to
CN9xx hence fixes that.
Patch 2: Check flow mask also before installing a src/dst
port filter, otherwise installing for one port installs for other one too.
====================

Link: https://lore.kernel.org/r/1658650874-16459-1-git-send-email-sbhatta@marvell.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Check the mask for non-zero value before installing tc filters
for L4 source and destination ports. Otherwise installing a
filter for source port installs destination port too and
vice-versa.

Fixes: 1d4d9e42 ("octeontx2-pf: Add tc flower hardware offload on ingress traffic")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

NIX_AF_TLXX_PIR/CIR register format has changed from OcteonTx2
to CN10K. CN10K supports larger burst size. Fix burst exponent
and burst mantissa configuration for CN10K.

Also fixed 'maxrate' from u32 to u64 since 'police.rate_bytes_ps'
passed by stack is also u64.

Fixes: e638a83f ("octeontx2-pf: TC_MATCHALL egress ratelimiting offload")
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Delete the redundant word 'in'.
Signed-off-by: wangjianli <wangjianli@cdjrlc.com>
Link: https://lore.kernel.org/r/20220724075207.21080-1-wangjianli@cdjrlc.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Delete the redundant word 'in'.
Signed-off-by: wangjianli <wangjianli@cdjrlc.com>
Link: https://lore.kernel.org/r/20220724074746.19550-1-wangjianli@cdjrlc.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Christian Marangi says:

====================
Add MTU change with stmmac interface running

This series is to permit MTU change while the interface is running.
Major rework are needed to permit to allocate a new dma conf based on
the new MTU before applying it. This is to make sure there is enough
space to allocate all the DMA queue before releasing the stmmac driver.

This was tested with a simple way to stress the network while the
interface is running.

2 ssh connection to the device:
- One generating simple traffic with while true; do free; done
- The other making the mtu change with a delay of 1 second

The connection is correctly stopped and recovered after the MTU is changed.

The first 2 patch of this series are minor fixup that fix problems
presented while testing this. One fix a problem when we renable a queue
while we are generating a new dma conf. The other is a corner case that
was notice while stressing the driver and turning down the interface while
there was some traffic.

(this is a follow-up of a simpler patch that wanted to add the same
feature. It was suggested to first try to check if it was possible to
apply the new configuration. Posting as RFC as it does major rework for
the new concept of DMA conf)
====================

Link: https://lore.kernel.org/r/20220723142933.16030-1-ansuelsmth@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Remove the limitation where the interface needs to be down to change
MTU by releasing and opening the stmmac driver to set the new MTU.
Also call the set_filter function to correctly init the port.
This permits to remove the EBUSY error while the ethernet port is
running permitting a correct MTU change if for example a DSA request
a MTU change for a switch CPU port.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Rework the driver to generate the stmmac dma_conf before stmmac_open.
This permits a function to first check if it's possible to allocate a
new dma_config and then pass it directly to __stmmac_open and "open" the
interface with the new configuration.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Move dma buf conf to dedicated struct. This in preparation for code
rework that will permit to allocate separate dma_conf without affecting
the priv struct.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Disable all queues and disconnect before tx_disable in stmmac_release to
prevent a corner case where packet may be still queued at the same time
tx_disable is called resulting in kernel panic if some packet still has
to be processed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Move queue reset to dedicated functions. This aside from a simple
cleanup is also required to allocate a dma conf without resetting the tx
queue while the device is temporarily detached as now the reset is not
part of the dma init function and can be done later in the code flow.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

delete extra space and tab in blank line, there is no functional change.
Reported-by: Hacash Robot <hacashRobot@santino.com>
Signed-off-by: William Dean <williamsukatube@gmail.com>
Link: https://lore.kernel.org/r/20220723073222.2961602-1-williamsukatube@163.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'wireless-next-2022-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next

Kalle Valo says:

====================
wireless-next patches for v5.20

Third set of patches for v5.20. MLO work continues and we have a lot
of stack changes due to that, including driver API changes. Not much
driver patches except on mt76.

Major changes:

cfg80211/mac80211
 - more prepartion for Wi-Fi 7 Multi-Link Operation (MLO) support,
   works with one link now
 - align with IEEE Draft P802.11be_D2.0
 - hardware timestamps for receive and transmit

mt76
 - preparation for new chipset support
 - ACPI SAR support

* tag 'wireless-next-2022-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (254 commits)
  wifi: mac80211: fix link data leak
  wifi: mac80211: mlme: fix disassoc with MLO
  wifi: mac80211: add macros to loop over active links
  wifi: mac80211: remove erroneous sband/link validation
  wifi: mac80211: mlme: transmit assoc frame with address translation
  wifi: mac80211: verify link addresses are different
  wifi: mac80211: rx: track link in RX data
  wifi: mac80211: optionally implement MLO multicast TX
  wifi: mac80211: expand ieee80211_mgmt_tx() for MLO
  wifi: nl80211: add MLO link ID to the NL80211_CMD_FRAME TX API
  wifi: mac80211: report link ID to cfg80211 on mgmt RX
  wifi: cfg80211: report link ID in NL80211_CMD_FRAME
  wifi: mac80211: add hardware timestamps for RX and TX
  wifi: cfg80211: add hardware timestamps to frame RX info
  wifi: cfg80211/nl80211: move rx management data into a struct
  wifi: cfg80211: add a function for reporting TX status with hardware timestamps
  wifi: nl80211: add RX and TX timestamp attributes
  wifi: ieee80211: add helper functions for detecting TM/FTM frames
  wifi: mac80211_hwsim: handle links for wmediumd/virtio
  wifi: mac80211: sta_info: fix link_sta insertion
  ...
====================

Link: https://lore.kernel.org/r/20220725174547.EA465C341C6@smtp.kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

These properties are inherited from ethernet-controller.yaml.
This fixes the dt_binding_check warning:
imx8mm-tqma8mqml-mba8mx.dt.yaml: ethernet@30be0000: 'nvmem-cell-names',
'nvmem-cells' do not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220720063924.1412799-1-alexander.stein@ew.tq-group.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

ath.git patches for v5.20. One fix and rest minor cleanup.