When PF performs a function reset, the hardware will reset both PF
and all the VF belong to this PF. Hence, both PF's driver and VF's
driver need to perform corresponding reset operations.

Before PF driver asserting function reset to hardware, it firstly
set up VF's hardware reset status, and inform the VF driver with
HNAE3_VF_PF_FUNC_RESET, then VF driver sets this reset type to
reset_pending and shechule reset task to stop IO and waits for the
hardware reset status to clear. When PF driver has reinitialized the
hardware and is ready to process mailbox from VF, PF driver clears
VF's hardware reset status for VF to continue its reset process.

Also, this patch uses readl_poll_timeout to simplify the hardware reset
status waitting.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently when VF need to reset itself, it will send a cmd to PF,
after receiving the VF reset requset, PF sends a cmd to inform
VF to enter the reset process and send a cmd to firmware to do the
actual reset for the VF, it is possible that firmware has resetted
the VF, but VF has not entered the reset process, which may cause
IO not stopped problem when firmware is resetting VF.

This patch fixes it by adjusting the VF reset process, when VF
need to reset itself, it will enter the reset process first, and
it will tell the PF to send cmd to firmware to reset itself.

Add member reset_pending to struct hclgevf_dev, which indicates that
there is reset event need to be processed by the VF's reset task, and
the VF's reset task chooses the highest-level one and clears other
low-level one when it processes reset_pending.

hclge_inform_reset_assert_to_vf function is unused now, but it will
be used to support the PF reset with VF working, so declare it in
the header file.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When doing reset, the reset handling function only need to
reinitialize hardware, it makes sense to add a function to
do that job. Also the error handling of hclgevf_init_hdev is
different when it is used in reset process.

This patch adds reset_hdev to reinitialize hardware when resetting.
Also, this patch removes the hclgevf_dev_ongoing_full_reset because
it is unused now.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The locally maintained list for tracking hash mac table was
not freed during driver remove.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mac_hlist was initialized during adapter_up, which will be called
every time a vf device is first brought up, or every time when device
is brought up again after bringing all devices down. This means our
state of previous list is lost, causing a memleak if entries are
present in the list. To fix that, move list init to the condition
that performs initial one time adapter setup.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The locally maintained list for tracking hash mac table was
not freed during driver remove.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

if skb is NULL pointer, and the following access of skb's
skb_mstamp_ns will trigger panic, which is same as BUG_ON
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RING_PUSH_REQUESTS_AND_CHECK_NOTIFY is already able to make sure backend sees
requests before req_prod is updated.
Signed-off-by: Jacob Wen <jian.w.wen@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
nfp: abm: move code and improve parameter validation

This set starts by separating Qdisc handling code into a new file.
Next two patches allow early access to TLV-based capabilities during
probe, previously the capabilities were parsed just before netdevs
were registered, but its cleaner to do some basic validation earlier
and avoid cleanup work.

Next three patches improve RED's parameter validation.  First we provide
a more precise message about why offload failed (and move the parameter
validation to a helper).  Next we make sure we don't set the top bit
in the 32 bit max RED threshold value.  Because FW is treating the value
as signed it reportedly causes slow downs (unnecessary queuing and
marking) when top bit is set with recent firmwares.  Last (and perhaps
least importantly) we offload the harddrop parameter of the Qdisc.
We don't plan to offload harddrop RED, but it seems prudent to make
sure user didn't set that flag as device behaviour would have differed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

RED Qdisc will now inform the drivers about the state of the harddrop
flag.  Refuse to offload in case harddrop is set.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To mirror software behaviour on offload more precisely inform
the drivers about the state of the harddrop flag.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Turns out the threshold value is used in signed compares in the FW,
so we should avoid setting the top bit.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Improve log messages printed when RED can't be offloaded because
of Qdisc parameters.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In certain cases initialization logic which follows allocation of
the vNIC structure may want to validate the capabilities of that vNIC.
This is easy before vNIC is initialized for normal capabilities which
are at fixed offsets in control memory, easy to locate and read, but
poses a challenge if the capabilities are in form of TLVs.  Parse
the TLVs early on so other code can just access parsed info, instead
of having to do the parsing by itself.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move setting ctrl_bar pointer to the nfp_net_alloc function,
to make sure we can parse capabilities early in the following
patch.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Qdisc offload code is logically separate, and we will soon
do significant surgery on it to support more Qdiscs, so move
it to a separate file.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recently, in commit ab408b6d ("tcp: switch tcp and sch_fq to new
earliest departure time model"), the TCP BBR code switched to a new
approach of using an explicit bbr_pacing_margin_percent for shaving a
pacing rate "haircut", rather than the previous implict
approach. Update an old comment to reflect the new approach.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michał Mirosław says:

====================
net: Use __vlan_hwaccel_*() helpers

This series removes from networking core and driver code an assumption
about how VLAN tag presence is stored in an skb. This will allow to free
up overloading of VLAN.CFI bit to incidate tag's presence.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

This removes assumption than vlan_tci != 0 when tag is present.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

This removes assumptions about VLAN_TAG_PRESENT bit.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use __vlan_hwaccel_put_tag() to set vlan tag and proto fields.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

__skb_checksum_complete_head() and __skb_checksum_complete()
are both declared in skbuff.h, they fit better in skbuff.c
than datagram.c.

Cc: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ivan Khoronzhuk says:

====================
net: ethernet: ti: cpsw: fix vlan mcast

The cpsw holds separate mcast entires for vlan entries. At this moment
driver adds only not vlan mcast addresses, omitting vlan/mcast entries.
As result mcast for vlans doesn't work. It can be fixed by adding same
mcast entries for every created vlan, but this patchseries uses more
sophisticated way and allows to create mcast entries only for vlans
that really require it. Generic functions from this series can be
reused for fixing vlan and macvlan unicast.

Simple example of ALE table before and after this series, having same
mcast entries as for vlan 100 as for real device (reserved vlan 2),
and one mcast address only for vlan 100 - 01:1b:19:00:00:00.

<---- Before this patchset ---->
vlan , vid = 2, untag_force = 0x5, reg_mcast = 0x5, mem_list = 0x5
mcast, vid = 2, addr = ff:ff:ff:ff:ff:ff, port_mask = 0x1
ucast, vid = 2, addr = 74:da:ea:47:7d:9d, persistant, port_num = 0x0
vlan , vid = 0, untag_force = 0x7, reg_mcast = 0x0, mem_list = 0x7
mcast, vid = 2, addr = 33:33:00:00:00:01, port_mask = 0x1
mcast, vid = 2, addr = 01:00:5e:00:00:01, port_mask = 0x1
vlan , vid = 1, untag_force = 0x3, reg_mcast = 0x3, mem_list = 0x3
mcast, vid = 1, addr = ff:ff:ff:ff:ff:ff, port_mask = 0x1
ucast, vid = 1, addr = 74:da:ea:47:7d:9c, persistant, port_num = 0x0
mcast, vid = 1, addr = 33:33:00:00:00:01, port_mask = 0x1
mcast, vid = 1, addr = 01:00:5e:00:00:01, port_mask = 0x1
mcast, vid = 2, addr = 01:80:c2:00:00:00, port_mask = 0x1
mcast, vid = 2, addr = 01:80:c2:00:00:03, port_mask = 0x1
mcast, vid = 2, addr = 01:80:c2:00:00:0e, port_mask = 0x1
mcast, vid = 1, addr = 01:80:c2:00:00:00, port_mask = 0x1
mcast, vid = 1, addr = 01:80:c2:00:00:03, port_mask = 0x1
mcast, vid = 1, addr = 01:80:c2:00:00:0e, port_mask = 0x1
mcast, vid = 2, addr = 33:33:ff:47:7d:9d, port_mask = 0x1
mcast, vid = 2, addr = 33:33:00:00:00:fb, port_mask = 0x1
mcast, vid = 2, addr = 33:33:00:01:00:03, port_mask = 0x1
mcast, vid = 1, addr = 33:33:ff:47:7d:9c, port_mask = 0x1
mcast, vid = 1, addr = 33:33:00:00:00:fb, port_mask = 0x1
mcast, vid = 1, addr = 33:33:00:01:00:03, port_mask = 0x1
mcast, vid = 1, addr = 01:00:5e:00:00:fb, port_mask = 0x1
mcast, vid = 1, addr = 01:00:5e:00:00:fc, port_mask = 0x1
vlan , vid = 100, untag_force = 0x0, reg_mcast = 0x5, mem_list = 0x5
ucast, vid = 100, addr = 74:da:ea:47:7d:9d, persistant, port_num = 0x0
mcast, vid = 100, addr = ff:ff:ff:ff:ff:ff, port_mask = 0x1
mcast, vid = 2, addr = 01:1b:19:00:00:00, port_mask = 0x1
			 ^^^
 Here mcast entry (ptpl2), has to be added only for vlan 100
 but added for reserved vlan 2...that's not enough.

<---- After this patchset ---->
vlan , vid = 2, untag_force = 0x5, reg_mcast = 0x5, mem_list = 0x5
mcast, vid = 2, addr = ff:ff:ff:ff:ff:ff, port_mask = 0x1
ucast, vid = 2, addr = 74:da:ea:47:7d:9d, persistant, port_num = 0x0
vlan , vid = 0, untag_force = 0x7, reg_mcast = 0x0, mem_list = 0x7
mcast, vid = 2, addr = 33:33:00:00:00:01, port_mask = 0x1
mcast, vid = 2, addr = 01:00:5e:00:00:01, port_mask = 0x1
vlan , vid = 1, untag_force = 0x3, reg_mcast = 0x3, mem_list = 0x3
mcast, vid = 1, addr = ff:ff:ff:ff:ff:ff, port_mask = 0x1
ucast, vid = 1, addr = 74:da:ea:47:7d:9c, persistant, port_num = 0x0
mcast, vid = 1, addr = 33:33:00:00:00:01, port_mask = 0x1
mcast, vid = 1, addr = 01:00:5e:00:00:01, port_mask = 0x1
mcast, vid = 2, addr = 01:80:c2:00:00:00, port_mask = 0x1
mcast, vid = 2, addr = 01:80:c2:00:00:03, port_mask = 0x1
mcast, vid = 2, addr = 01:80:c2:00:00:0e, port_mask = 0x1
mcast, vid = 1, addr = 01:80:c2:00:00:00, port_mask = 0x1
mcast, vid = 1, addr = 01:80:c2:00:00:03, port_mask = 0x1
mcast, vid = 1, addr = 01:80:c2:00:00:0e, port_mask = 0x1
mcast, vid = 2, addr = 33:33:ff:47:7d:9d, port_mask = 0x1
mcast, vid = 1, addr = 33:33:ff:47:7d:9c, port_mask = 0x1
mcast, vid = 2, addr = 33:33:00:00:00:fb, port_mask = 0x1
mcast, vid = 2, addr = 33:33:00:01:00:03, port_mask = 0x1
mcast, vid = 1, addr = 33:33:00:00:00:fb, port_mask = 0x1
mcast, vid = 1, addr = 33:33:00:01:00:03, port_mask = 0x1
vlan , vid = 100, untag_force = 0x0, reg_mcast = 0x5, mem_list = 0x5
ucast, vid = 100, addr = 74:da:ea:47:7d:9d, persistant, port_num = 0x0
mcast, vid = 100, addr = ff:ff:ff:ff:ff:ff, port_mask = 0x1
mcast, vid = 100, addr = 33:33:00:00:00:01, port_mask = 0x1
mcast, vid = 100, addr = 01:00:5e:00:00:01, port_mask = 0x1
mcast, vid = 100, addr = 33:33:ff:47:7d:9d, port_mask = 0x1
mcast, vid = 100, addr = 01:80:c2:00:00:00, port_mask = 0x1
mcast, vid = 100, addr = 01:80:c2:00:00:03, port_mask = 0x1
mcast, vid = 100, addr = 01:80:c2:00:00:0e, port_mask = 0x1
mcast, vid = 100, addr = 33:33:00:00:00:fb, port_mask = 0x1
mcast, vid = 100, addr = 33:33:00:01:00:03, port_mask = 0x1
mcast, vid = 100, addr = 01:1b:19:00:00:00, port_mask = 0x1
			 ^^^
    Here mcast entry (ptpl2), is added only for vlan 100
    as it should be.

Based on net-next/master

v2..v1:
  net: ethernet: ti: cpsw: fix vlan mcast
	- removed limit for legacy switch cpsw mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The vlan configuration is not restored after interface donw/up sequence
(if dual-emac - both interfaces). Tested on am572x EVM.

Steps to check:
~# ip link add link eth1 name eth1.100 type vlan id 100
~# ifconfig eth0 down
~# ifconfig eth1 down

Try to remove vid and observe warning:
~# ip link del eth1.100
[  739.526757] net eth1: removing vlanid 100 from vlan filter
[  739.533322] failed to kill vid 0081/100 for device eth1

This patch fixes it, restoring only vlan ALE entries and all other
unicast/multicast entries are restored by system calling rx_mode ndo.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

At this moment, mcast addresses are added for real device only
(reserved vlans for dual-emac mode), even if a mcast address was added
for some vlan only, thus ALE doesn't have corresponding vlan mcast
entries after vlan socket joined multicast group. So ALE drops vlan
frames with mcast addresses intended for vlans and potentially can
receive mcast frames for base ndev. That's not correct. So, fix it by
creating only vlan/mcast entries as requested. Patch doesn't use any
additional lists and is based on device mc address list and cpsw ALE
table entries.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

It's redundancy for the drivers to hold the list of vlans when
absolutely the same list exists in vlan core. In most cases it's
needed only to traverse the vlan devices, their vids and sync some
settings with h/w, so add API to simplify this.

At least some of these drivers also can benefit:
grep "for_each.*vid" -r drivers/net/ethernet/

drivers/net/ethernet/hisilicon/hns3/hns3_enet.c:
drivers/net/ethernet/synopsys/dwc-xlgmac-hw.c:
drivers/net/ethernet/qlogic/qlge/qlge_main.c:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c:
drivers/net/ethernet/via/via-rhine.c:
drivers/net/ethernet/via/via-velocity.c:
drivers/net/ethernet/intel/igb/igb_main.c:
drivers/net/ethernet/intel/ice/ice_main.c:
drivers/net/ethernet/intel/e1000/e1000_main.c:
drivers/net/ethernet/intel/i40e/i40e_main.c:
drivers/net/ethernet/intel/e1000e/netdev.c:
drivers/net/ethernet/intel/igbvf/netdev.c:
drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c:
drivers/net/ethernet/intel/ixgb/ixgb_main.c:
drivers/net/ethernet/intel/ixgbe/ixgbe_main.c:
drivers/net/ethernet/amd/xgbe/xgbe-dev.c:
drivers/net/ethernet/emulex/benet/be_main.c:
drivers/net/ethernet/neterion/vxge/vxge-main.c:
drivers/net/ethernet/adaptec/starfire.c:
drivers/net/ethernet/brocade/bna/bnad.c:
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to avoid all table update, and only remove or add new
address, the auxiliary function exists, named __hw_addr_sync_dev().
It allows end driver do nothing when nothing changed and add/rm when
concrete address is firstly added or lastly removed. But it doesn't
include cases when an address of real device or vlan was reused by
other vlans or vlan/macval devices.

For handaling events when address was reused/unreused the patch adds
new auxiliary routine - __hw_addr_ref_sync_dev(). It allows to do
nothing when nothing was changed and do updates only for an address
being added/reused/deleted/unreused. Thus, clone address changes for
vlans can be mirrored in the table. The function is exclusive with
__hw_addr_sync_dev(). It's responsibility of the end driver to
identify address vlan device, if it needs so.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

As added in 3e59020a ("net: bql: add __netdev_tx_sent_queue()"), which
 see for performance rationale.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michał Mirosław says:

====================
net: Remove VLAN_TAG_PRESENT from drivers

This series removes VLAN_TAG_PRESENT use from network drivers in
preparation to removing its special meaning.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a minimal change to allow removing of VLAN_TAG_PRESENT.
It leaves OVS unable to use CFI bit, as fixing this would need
a deeper surgery involving userspace interface.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

This just removes VLAN_TAG_PRESENT use.  VLAN TCI=0 special meaning is
deeply embedded in the driver code and so is left as is.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

return -ENOMEM directly instead of assigning it in a variable
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>