commit fb7a9174 upstream.

A warning message during SRIOV multicast cleanup should have actually been
a debug level message. The condition generating the warning does no harm
and can fill the message log.

In some cases, during testing, some tests were so intense as to swamp the
message log with these warning messages, causing a stall in the console
message log output task. This stall caused an NMI to be sent to all CPUs
(so that they all dumped their stacks into the message log).
Aside from the message flood causing an NMI, the tests all passed.

Once the message flood which caused the NMI is removed (by reducing the
warning message to debug level), the NMI no longer occurs.

Sample message log (console log) output illustrating the flood and
resultant NMI (snippets with comments and modified with ... instead
of hex digits, to satisfy checkpatch.pl):

 <mlx4_ib> _mlx4_ib_mcg_port_cleanup: ... WARNING: group refcount 1!!!...
 *** About 4000 almost identical lines in less than one second ***
 <mlx4_ib> _mlx4_ib_mcg_port_cleanup: ... WARNING: group refcount 1!!!...
 INFO: rcu_sched detected stalls on CPUs/tasks: { 17} (...)
 *** { 17} above indicates that CPU 17 was the one that stalled ***
 sending NMI to all CPUs:
 ...
 NMI backtrace for cpu 17
 CPU: 17 PID: 45909 Comm: kworker/17:2
 Hardware name: HP ProLiant DL360p Gen8, BIOS P71 09/08/2013
 Workqueue: events fb_flashcursor
 task: ffff880478...... ti: ffff88064e...... task.ti: ffff88064e......
 RIP: 0010:[ffffffff81......]  [ffffffff81......] io_serial_in+0x15/0x20
 RSP: 0018:ffff88064e257cb0  EFLAGS: 00000002
 RAX: 0000000000...... RBX: ffffffff81...... RCX: 0000000000......
 RDX: 0000000000...... RSI: 0000000000...... RDI: ffffffff81......
 RBP: ffff88064e...... R08: ffffffff81...... R09: 0000000000......
 R10: 0000000000...... R11: ffff88064e...... R12: 0000000000......
 R13: 0000000000...... R14: ffffffff81...... R15: 0000000000......
 FS:  0000000000......(0000) GS:ffff8804af......(0000) knlGS:000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080......
 CR2: 00007f2a2f...... CR3: 0000000001...... CR4: 0000000000......
 DR0: 0000000000...... DR1: 0000000000...... DR2: 0000000000......
 DR3: 0000000000...... DR6: 00000000ff...... DR7: 0000000000......
 Stack:
 ffff88064e...... ffffffff81...... ffffffff81...... 0000000000......
 ffffffff81...... ffff88064e...... ffffffff81...... ffffffff81......
 ffffffff81...... ffff88064e...... ffffffff81...... 0000000000......
 Call Trace:
[<ffffffff813d099b>] wait_for_xmitr+0x3b/0xa0
[<ffffffff813d0b5c>] serial8250_console_putchar+0x1c/0x30
[<ffffffff813d0b40>] ? serial8250_console_write+0x140/0x140
[<ffffffff813cb5fa>] uart_console_write+0x3a/0x80
[<ffffffff813d0aae>] serial8250_console_write+0xae/0x140
[<ffffffff8107c4d1>] call_console_drivers.constprop.15+0x91/0xf0
[<ffffffff8107d6cf>] console_unlock+0x3bf/0x400
[<ffffffff813503cd>] fb_flashcursor+0x5d/0x140
[<ffffffff81355c30>] ? bit_clear+0x120/0x120
[<ffffffff8109d5fb>] process_one_work+0x17b/0x470
[<ffffffff8109e3cb>] worker_thread+0x11b/0x400
[<ffffffff8109e2b0>] ? rescuer_thread+0x400/0x400
[<ffffffff810a5aef>] kthread+0xcf/0xe0
[<ffffffff810a5a20>] ? kthread_create_on_node+0x140/0x140
[<ffffffff81645858>] ret_from_fork+0x58/0x90
[<ffffffff810a5a20>] ? kthread_create_on_node+0x140/0x140
Code: 48 89 e5 d3 e6 48 63 f6 48 03 77 10 8b 06 5d c3 66 0f 1f 44 00 00 66 66 66 6

As indicated in the stack trace above, the console output task got swamped.

Fixes: b9c5d6a6 ("IB/mlx4: Add multicast group (MCG) paravirtualization for SR-IOV")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 99e68909 upstream.

In mlx4_ib_add, procedure mlx4_ib_alloc_eqs is called to allocate EQs.

However, in the mlx4_ib_add error flow, procedure mlx4_ib_free_eqs is not
called to free the allocated EQs.

Fixes: e605b743 ("IB/mlx4: Increase the number of vectors (EQs) available for ULPs")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 771a5258 upstream.

When udev renames the netdev devices, ipoib debugfs entries does not
get renamed. As a result, if subsequent probe of ipoib device reuse the
name then creating a debugfs entry for the new device would fail.

Also, moved ipoib_create_debug_files and ipoib_delete_debug_files as part
of ipoib event handling in order to avoid any race condition between these.

Fixes: 1732b0ef ([IPoIB] add path record information in debugfs)
Signed-off-by: Vijay Kumar <vijay.ac.kumar@oracle.com>
Signed-off-by: Shamir Rabinovitch <shamir.rabinovitch@oracle.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b312be3d upstream.

The kernel commit cited below restructured ib device management
so that the device kobject is initialized in ib_alloc_device.

As part of the restructuring, the kobject is now initialized in
procedure ib_alloc_device, and is later added to the device hierarchy
in the ib_register_device call stack, in procedure
ib_device_register_sysfs (which calls device_add).

However, in the ib_device_register_sysfs error flow, if an error
occurs following the call to device_add, the cleanup procedure
device_unregister is called. This call results in the device object
being deleted -- which results in various use-after-free crashes.

The correct cleanup call is device_del -- which undoes device_add
without deleting the device object.

The device object will then (correctly) be deleted in the
ib_register_device caller's error cleanup flow, when the caller invokes
ib_dealloc_device.

Fixes: 55aeed06 ("IB/core: Make ib_alloc_device init the kobject")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 0cfef2b7 upstream.

If the mmap_sem is contented then the vfio type1 IOMMU backend will
defer locked page accounting updates to a workqueue task.  This has a
few problems and depending on which side the user tries to play, they
might be over-penalized for unmaps that haven't yet been accounted or
race the workqueue to enter more mappings than they're allowed.  The
original intent of this workqueue mechanism seems to be focused on
reducing latency through the ioctl, but we cannot do so at the cost
of correctness.  Remove this workqueue mechanism and update the
callers to allow for failure.  We can also now recheck the limit under
write lock to make sure we don't exceed it.

vfio_pin_pages_remote() also now necessarily includes an unwind path
which we can jump to directly if the consecutive page pinning finds
that we're exceeding the user's memory limits.  This avoids the
current lazy approach which does accounting and mapping up to the
fault, only to return an error on the next iteration to unwind the
entire vfio_dma.

Cc: stable@vger.kernel.org
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Kirti Wankhede <kwankhede@nvidia.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 117aceb0 upstream.

When committing era metadata to disk, it doesn't always save the latest
spacemap metadata root in superblock. Due to this, metadata is getting
corrupted sometimes when reopening the device. The correct order of update
should be, pre-commit (shadows spacemap root), save the spacemap root
(newly shadowed block) to in-core superblock and then the final commit.
Signed-off-by: Somasundaram Krishnasamy <somasundaram.krishnasamy@oracle.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2a2a251f upstream.

Some cipher implementations will crash if you try to use them
without calling setkey first.  This patch adds a check so that
the accept(2) call will fail with -ENOKEY if setkey hasn't been
done on the socket yet.

Fixes: 400c40cf ("crypto: algif - add AEAD support")
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2859323e upstream.

When registering an integrity profile: if the template's interval_exp is
not 0 use it, otherwise use the ilog2() of logical block size of the
provided gendisk.

This fixes a long-standing DM linear target bug where it cannot pass
integrity data to the underlying device if its logical block size
conflicts with the underlying device's logical block size.
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6c7a5dce upstream.

Fix potential races in kvm_psci_vcpu_on() by taking the kvm->lock
mutex.  In general, it's a bad idea to allow more than one PSCI_CPU_ON
to process the same target VCPU at the same time.  One such problem
that may arise is that one PSCI_CPU_ON could be resetting the target
vcpu, which fills the entire sys_regs array with a temporary value
including the MPIDR register, while another looks up the VCPU based
on the MPIDR value, resulting in no target VCPU found.  Resolves both
races found with the kvm-unit-tests/arm/psci unit test.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Reported-by: Levente Kurusa <lkurusa@redhat.com>
Suggested-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 28bf2888 upstream.

If we already entered/are about to enter SMM, don't allow switching to
INIT/SIPI_RECEIVED, otherwise the next call to kvm_apic_accept_events()
will report a warning.

Same applies if we are already in MP state INIT_RECEIVED and SMM is
requested to be turned on. Refuse to set the VCPU events in this case.

Fixes: cd7764fe ("KVM: x86: latch INITs while in system management mode")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 9abc74a2 upstream.

This is broken since ever but sadly nobody noticed.
Recent versions of GDB set DR_CONTROL unconditionally and
UML dies due to a heap corruption. It turns out that
the PTRACE_POKEUSER was copy&pasted from i386 and assumes
that addresses are 4 bytes long.

Fix that by using 8 as address size in the calculation.
Reported-by: jie cao <cj3054@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8376efd3 upstream.

Commit 11e63f6d added cache flushing for unaligned writes from an
iovec, covering the first and last cache line of a >= 8 byte write and
the first cache line of a < 8 byte write.  But an unaligned write of
2-7 bytes can still cover two cache lines, so make sure we flush both
in that case.

Fixes: 11e63f6d ("x86, pmem: fix broken __copy_user_nocache ...")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 65973dd3 upstream.

i386 glibc is buggy and calls the sigaction syscall incorrectly.

This is asymptomatic for normal programs, but it blows up on
programs that do evil things with segmentation.  The ldt_gdt
self-test is an example of such an evil program.

This doesn't appear to be a regression -- I think I just got lucky
with the uninitialized memory that glibc threw at the kernel when I
wrote the test.

This hackish fix manually issues sigaction(2) syscalls to undo the
damage.  Without the fix, ldt_gdt_32 segfaults; with the fix, it
passes for me.

See: https://sourceware.org/bugzilla/show_bug.cgi?id=21269Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Garnier <thgarnie@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/aaab0f9f93c9af25396f01232608c163a760a668.1490218061.git.luto@kernel.orgSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d594aa02 upstream.

The minimum size for a new stack (512 bytes) setup for arch/x86/boot components
when the bootloader does not setup/provide a stack for the early boot components
is not "enough".

The setup code executing as part of early kernel startup code, uses the stack
beyond 512 bytes and accidentally overwrites and corrupts part of the BSS
section. This is exposed mostly in the early video setup code, where
it was corrupting BSS variables like force_x, force_y, which in-turn affected
kernel parameters such as screen_info (screen_info.orig_video_cols) and
later caused an exception/panic in console_init().

Most recent boot loaders setup the stack for early boot components, so this
stack overwriting into BSS section issue has not been exposed.
Signed-off-by: Ashish Kalra <ashish@bluestacks.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170419152015.10011-1-ashishkalra@Ashishs-MacBook-Pro.localSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f5cccf49 upstream.

While running a bind/unbind stress test with the dwc3 usb driver on rk3399,
the following crash was observed.

Unable to handle kernel NULL pointer dereference at virtual address 00000218
pgd = ffffffc00165f000
[00000218] *pgd=000000000174f003, *pud=000000000174f003,
				*pmd=0000000001750003, *pte=00e8000001751713
Internal error: Oops: 96000005 [#1] PREEMPT SMP
Modules linked in: uinput uvcvideo videobuf2_vmalloc cmac
ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat rfcomm
xt_mark fuse bridge stp llc zram btusb btrtl btbcm btintel bluetooth
ip6table_filter mwifiex_pcie mwifiex cfg80211 cdc_ether usbnet r8152 mii joydev
snd_seq_midi snd_seq_midi_event snd_rawmidi snd_seq snd_seq_device ppp_async
ppp_generic slhc tun
CPU: 1 PID: 29814 Comm: kworker/1:1 Not tainted 4.4.52 #507
Hardware name: Google Kevin (DT)
Workqueue: pm pm_runtime_work
task: ffffffc0ac540000 ti: ffffffc0af4d4000 task.ti: ffffffc0af4d4000
PC is at autosuspend_check+0x74/0x174
LR is at autosuspend_check+0x70/0x174
...
Call trace:
[<ffffffc00080dcc0>] autosuspend_check+0x74/0x174
[<ffffffc000810500>] usb_runtime_idle+0x20/0x40
[<ffffffc000785ae0>] __rpm_callback+0x48/0x7c
[<ffffffc000786af0>] rpm_idle+0x1e8/0x498
[<ffffffc000787cdc>] pm_runtime_work+0x88/0xcc
[<ffffffc000249bb8>] process_one_work+0x390/0x6b8
[<ffffffc00024abcc>] worker_thread+0x480/0x610
[<ffffffc000251a80>] kthread+0x164/0x178
[<ffffffc0002045d0>] ret_from_fork+0x10/0x40

Source:

(gdb) l *0xffffffc00080dcc0
0xffffffc00080dcc0 is in autosuspend_check
(drivers/usb/core/driver.c:1778).
1773		/* We don't need to check interfaces that are
1774		 * disabled for runtime PM.  Either they are unbound
1775		 * or else their drivers don't support autosuspend
1776		 * and so they are permanently active.
1777		 */
1778		if (intf->dev.power.disable_depth)
1779			continue;
1780		if (atomic_read(&intf->dev.power.usage_count) > 0)
1781			return -EBUSY;
1782		w |= intf->needs_remote_wakeup;

Code analysis shows that intf is set to NULL in usb_disable_device() prior
to setting actconfig to NULL. At the same time, usb_runtime_idle() does not
lock the usb device, and neither does any of the functions in the
traceback. This means that there is no protection against a race condition
where usb_disable_device() is removing dev->actconfig->interface[] pointers
while those are being accessed from autosuspend_check().

To solve the problem, synchronize and validate device state between
autosuspend_check() and usb_disconnect().
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 245b2eec upstream.

While stress testing a usb controller using a bind/unbind looop, the
following error loop was observed.

usb 7-1.2: new low-speed USB device number 3 using xhci-hcd
usb 7-1.2: hub failed to enable device, error -108
usb 7-1-port2: cannot disable (err = -22)
usb 7-1-port2: couldn't allocate usb_device
usb 7-1-port2: cannot disable (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: activate --> -22
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
hub 7-1:1.0: hub_ext_port_status failed (err = -22)
** 57 printk messages dropped ** hub 7-1:1.0: activate --> -22
** 82 printk messages dropped ** hub 7-1:1.0: hub_ext_port_status failed (err = -22)

This continues forever. After adding tracebacks into the code,
the call sequence leading to this is found to be as follows.

[<ffffffc0007fc8e0>] hub_activate+0x368/0x7b8
[<ffffffc0007fceb4>] hub_resume+0x2c/0x3c
[<ffffffc00080b3b8>] usb_resume_interface.isra.6+0x128/0x158
[<ffffffc00080b5d0>] usb_suspend_both+0x1e8/0x288
[<ffffffc00080c9c4>] usb_runtime_suspend+0x3c/0x98
[<ffffffc0007820a0>] __rpm_callback+0x48/0x7c
[<ffffffc00078217c>] rpm_callback+0xa8/0xd4
[<ffffffc000786234>] rpm_suspend+0x84/0x758
[<ffffffc000786ca4>] rpm_idle+0x2c8/0x498
[<ffffffc000786ed4>] __pm_runtime_idle+0x60/0xac
[<ffffffc00080eba8>] usb_autopm_put_interface+0x6c/0x7c
[<ffffffc000803798>] hub_event+0x10ac/0x12ac
[<ffffffc000249bb8>] process_one_work+0x390/0x6b8
[<ffffffc00024abcc>] worker_thread+0x480/0x610
[<ffffffc000251a80>] kthread+0x164/0x178
[<ffffffc0002045d0>] ret_from_fork+0x10/0x40

kick_hub_wq() is called from hub_activate() even after failures to
communicate with the hub. This results in an endless sequence of
hub event -> hub activate -> wq trigger -> hub event -> ...

Provide two solutions for the problem.

- Only trigger the hub event queue if communication with the hub
  is successful.
- After a suspend failure, only resume already suspended interfaces
  if the communication with the device is still possible.

Each of the changes fixes the observed problem. Use both to improve
robustness.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3d615964 upstream.

DWC3 driver uses of_usb_get_phy_mode() which is
implemented in drivers/usb/phy/of.c and in bare minimal
configuration it might not be pulled in kernel binary.

In case of ARC or ARM this could be easily reproduced with
"allnodefconfig" +CONFIG_USB=m +CONFIG_USB_DWC3=m.

On building all ends-up with:
---------------------->8------------------
  Kernel: arch/arm/boot/Image is ready
  Kernel: arch/arm/boot/zImage is ready
  Building modules, stage 2.
  MODPOST 5 modules
ERROR: "of_usb_get_phy_mode" [drivers/usb/dwc3/dwc3.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
---------------------->8------------------
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: linux-snps-arc@lists.infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2c930e3d upstream.

Add missing continue in switch.

Addresses-Coverity-ID: 1248733
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8ec04a49 upstream.

The timer expiry routine `jr3_pci_poll_dev()` checks for expiry by
checking whether the absolute value of `jiffies` (stored in local
variable `now`) is greater than the expected expiry time in jiffy units.
This will fail when `jiffies` wraps around.  Also, it seems to make
sense to handle the expiry one jiffy earlier than the current test.  Use
`time_after_eq()` to check for expiry.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 45292be0 upstream.

For some reason, the driver does not consider allocation of the
subdevice private data to be a fatal error when attaching the COMEDI
device.  It tests the subdevice private data pointer for validity at
certain points, but omits some crucial tests.  In particular,
`jr3_pci_auto_attach()` calls `jr3_pci_alloc_spriv()` to allocate and
initialize the subdevice private data, but the same function
subsequently dereferences the pointer to access the `next_time_min` and
`next_time_max` members without checking it first.  The other missing
test is in the timer expiry routine `jr3_pci_poll_dev()`, but it will
crash before it gets that far.

Fix the bug by returning `-ENOMEM` from `jr3_pci_auto_attach()` as soon
as one of the calls to `jr3_pci_alloc_spriv()` returns `NULL`.  The
COMEDI core will subsequently call `jr3_pci_detach()` to clean up.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b58f45c8 upstream.

Make sure to deregister the USB driver before releasing the tty driver
to avoid use-after-free in the USB disconnect callback where the tty
devices are deregistered.

Fixes: 61e12104 ("staging: gdm7240: adding LTE USB driver")
Cc: Won Kang <wkang77@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 12ecd24e upstream.

Since 4.9 mandated USB buffers be heap allocated this causes the driver
to fail.

Since there is a wide range of buffer sizes use kmemdup to create
allocated buffer.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 05c0cf88 upstream.

Since 4.9 mandated USB buffers to be heap allocated. This causes
the driver to fail.

Create buffer for USB transfers.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: Proper handling of Race Condition when two USB class drivers try to call init_usb_class simultaneously

commit 2f86a96b upstream.

There is race condition when two USB class drivers try to call
init_usb_class at the same time and leads to crash.
code path: probe->usb_register_dev->init_usb_class

To solve this, mutex locking has been added in init_usb_class() and
destroy_usb_class().

As pointed by Alan, removed "if (usb_class)" test from destroy_usb_class()
because usb_class can never be NULL there.
Signed-off-by: Ajay Kaher <ajay.kaher@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 31c5d192 upstream.

This development kit has an FT4232 on it with a custom USB VID/PID.
The FT4232 provides four UARTs, but only two are used. The UART 0
is used by the FlashPro5 programmer and UART 2 is connected to the
SmartFusion2 CortexM3 SoC UART port.

Note that the USB VID is registered to Actel according to Linux USB
VID database, but that was acquired by Microsemi.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6fc091fb upstream.

Print correct command ring address using 'val_64'.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 197b806a upstream.

While testing modification of per se_node_acl queue_depth forcing
session reinstatement via lio_target_nacl_cmdsn_depth_store() ->
core_tpg_set_initiator_node_queue_depth(), a hung task bug triggered
when changing cmdsn_depth invoked session reinstatement while an iscsi
login was already waiting for session reinstatement to complete.

This can happen when an outstanding se_cmd descriptor is taking a
long time to complete, and session reinstatement from iscsi login
or cmdsn_depth change occurs concurrently.

To address this bug, explicitly set session_fall_back_to_erl0 = 1
when forcing session reinstatement, so session reinstatement is
not attempted if an active session is already being shutdown.

This patch has been tested with two scenarios.  The first when
iscsi login is blocked waiting for iscsi session reinstatement
to complete followed by queue_depth change via configfs, and
second when queue_depth change via configfs us blocked followed
by a iscsi login driven session reinstatement.

Note this patch depends on commit d36ad77f to handle multiple
sessions per se_node_acl when changing cmdsn_depth, and for
pre v4.5 kernels will need to be included for stable as well.
Reported-by: Gary Guo <ghg@datera.io>
Tested-by: Gary Guo <ghg@datera.io>
Cc: Gary Guo <ghg@datera.io>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d36ad77f upstream.

This patch converts core_tpg_set_initiator_node_queue_depth()
to use struct se_node_acl->acl_sess_list when performing
explicit se_tpg_tfo->shutdown_session() for active sessions,
in order for new se_node_acl->queue_depth to take effect.

This follows how core_tpg_del_initiator_node_acl() currently
works when invoking se_tpg_tfo->shutdown-session(), and ahead
of the next patch to take se_node_acl->acl_kref during lookup,
the extra get_initiator_node_acl() can go away. In order to
achieve this, go ahead and change target_get_session() to use
kref_get_unless_zero() and propigate up the return value
to know when a session is already being released.

This is because se_node_acl->acl_group is already protecting
se_node_acl->acl_group reference via configfs, and shutdown
within core_tpg_del_initiator_node_acl() won't occur until
sys_write() to core_tpg_set_initiator_node_queue_depth()
attribute returns back to user-space.

Also, drop the left-over iscsi-target hack, and obtain
se_portal_group->session_lock in lio_tpg_shutdown_session()
internally. Remove iscsi-target wrapper and unused se_tpg +
force parameters and associated code.
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 59ac9c07 upstream.

This patch fixes zero-length READ and WRITE handling in target/FILEIO,
which was broken a long time back by:

Since:

  commit d81cb447
  Author: Paolo Bonzini <pbonzini@redhat.com>
  Date:   Mon Sep 17 16:36:11 2012 -0700

      target: go through normal processing for all zero-length commands

which moved zero-length READ and WRITE completion out of target-core,
to doing submission into backend driver code.

To address this, go ahead and invoke target_complete_cmd() for any
non negative return value in fd_do_rw().
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: David Disseldorp <ddiss@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a71a5dc7 upstream.

Following the bugfix for handling non SAM_STAT_GOOD COMPARE_AND_WRITE
status during COMMIT phase in commit 9b2792c3, the same bug exists
for the READ phase as well.

This would manifest first as a lost SCSI response, and eventual
hung task during fabric driver logout or re-login, as existing
shutdown logic waited for the COMPARE_AND_WRITE se_cmd->cmd_kref
to reach zero.

To address this bug, compare_and_write_callback() has been changed
to set post_ret = 1 and return TCM_LOGICAL_UNIT_COMMUNICATION_FAILURE
as necessary to signal failure status.
Reported-by: Bill Borsari <wgb@datera.io>
Cc: Bill Borsari <wgb@datera.io>
Tested-by: Gary Guo <ghg@datera.io>
Cc: Gary Guo <ghg@datera.io>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 69861e0a upstream.

When booted as pv-guest the p2m list presented by the Xen is already
mapped to virtual addresses. In dom0 case the hypervisor might make use
of 2M- or 1G-pages for this mapping. Unfortunately while being properly
aligned in virtual and machine address space, those pages might not be
aligned properly in guest physical address space.

So when trying to obtain the guest physical address of such a page
pud_pfn() and pmd_pfn() must be avoided as those will mask away guest
physical address bits not being zero in this special case.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 19b7ccf8 upstream.

Commit 25520d55 ("block: Inline blk_integrity in struct gendisk")
introduced blk_integrity_revalidate(), which seems to assume ownership
of the stable pages flag and unilaterally clears it if no blk_integrity
profile is registered:

    if (bi->profile)
            disk->queue->backing_dev_info->capabilities |=
                    BDI_CAP_STABLE_WRITES;
    else
            disk->queue->backing_dev_info->capabilities &=
                    ~BDI_CAP_STABLE_WRITES;

It's called from revalidate_disk() and rescan_partitions(), making it
impossible to enable stable pages for drivers that support partitions
and don't use blk_integrity: while the call in revalidate_disk() can be
trivially worked around (see zram, which doesn't support partitions and
hence gets away with zram_revalidate_disk()), rescan_partitions() can
be triggered from userspace at any time.  This breaks rbd, where the
ceph messenger is responsible for generating/verifying CRCs.

Since blk_integrity_{un,}register() "must" be used for (un)registering
the integrity profile with the block layer, move BDI_CAP_STABLE_WRITES
setting there.  This way drivers that call blk_integrity_register() and
use integrity infrastructure won't interfere with drivers that don't
but still want stable pages.

Fixes: 25520d55 ("block: Inline blk_integrity in struct gendisk")
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Mike Snitzer <snitzer@redhat.com>
Tested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
[idryomov@gmail.com: backport to < 4.11: bdi is embedded in queue]
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3089c1df upstream.

The vm fault handler relies on the fact that the VMA owns a reference
to the BO. However, once mmap_sem is released, other tasks are free to
destroy the VMA, which can lead to the BO being freed. Fix two code
paths where that can happen, both related to vm fault retries.

Found via a lock debugging warning which flagged &bo->wu_mutex as
locked while being destroyed.

Fixes: cbe12e74 ("drm/ttm: Allow vm fault retries")
Signed-off-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b9dd4618 upstream.

F2FS uses 4 bytes to represent block address. As a result, supported
size of disk is 16 TB and it equals to 16 * 1024 * 1024 / 2 segments.
Signed-off-by: Jin Qian <jinqian@google.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit ac45bd93 ]

We have the number of longs, but we need to calculate the number of
bytes required.

Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 242d3a49 ]

For each netns (except init_net), we initialize its null entry
in 3 places:

1) The template itself, as we use kmemdup()
2) Code around dst_init_metrics() in ip6_route_net_init()
3) ip6_route_dev_notify(), which is supposed to initialize it after
   loopback registers

Unfortunately the last one still happens in a wrong order because
we expect to initialize net->ipv6.ip6_null_entry->rt6i_idev to
net->loopback_dev's idev, thus we have to do that after we add
idev to loopback. However, this notifier has priority == 0 same as
ipv6_dev_notf, and ipv6_dev_notf is registered after
ip6_route_dev_notifier so it is called actually after
ip6_route_dev_notifier. This is similar to commit 2f460933
("ipv6: initialize route null entry in addrconf_init()") which
fixes init_net.

Fix it by picking a smaller priority for ip6_route_dev_notifier.
Also, we have to release the refcnt accordingly when unregistering
loopback_dev because device exit functions are called before subsys
exit functions.
Acked-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 2f460933 ]

Andrey reported a crash on init_net.ipv6.ip6_null_entry->rt6i_idev
since it is always NULL.

This is clearly wrong, we have code to initialize it to loopback_dev,
unfortunately the order is still not correct.

loopback_dev is registered very early during boot, we lose a chance
to re-initialize it in notifier. addrconf_init() is called after
ip6_route_init(), which means we have no chance to correct it.

Fix it by moving this initialization explicitly after
ipv6_add_dev(init_net.loopback_dev) in addrconf_init().
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 77ef033b ]

IFLA_PHYS_PORT_NAME is a string attribute, so terminate it with \0.
Otherwise libnl3 fails to validate netlink messages with this attribute.
"ip -detail a" assumes too that the attribute is NUL-terminated when
printing it. It often was, due to padding.

I noticed this as libvirtd failing to start on a system with sfc driver
after upgrading it to Linux 4.11, i.e. when sfc added support for
phys_port_name.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 86f4c90a ]

raw_send_hdrinc() and rawv6_send_hdrinc() expect that the buffer copied
from the userspace contains the IPv4/IPv6 header, so if too few bytes are
copied, parts of the header may remain uninitialized.

This bug has been detected with KMSAN.

For the record, the KMSAN report:

==================================================================
BUG: KMSAN: use of unitialized memory in nf_ct_frag6_gather+0xf5a/0x44a0
inter: 0
CPU: 0 PID: 1036 Comm: probe Not tainted 4.11.0-rc5+ #2455
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:16
 dump_stack+0x143/0x1b0 lib/dump_stack.c:52
 kmsan_report+0x16b/0x1e0 mm/kmsan/kmsan.c:1078
 __kmsan_warning_32+0x5c/0xa0 mm/kmsan/kmsan_instr.c:510
 nf_ct_frag6_gather+0xf5a/0x44a0 net/ipv6/netfilter/nf_conntrack_reasm.c:577
 ipv6_defrag+0x1d9/0x280 net/ipv6/netfilter/nf_defrag_ipv6_hooks.c:68
 nf_hook_entry_hookfn ./include/linux/netfilter.h:102
 nf_hook_slow+0x13f/0x3c0 net/netfilter/core.c:310
 nf_hook ./include/linux/netfilter.h:212
 NF_HOOK ./include/linux/netfilter.h:255
 rawv6_send_hdrinc net/ipv6/raw.c:673
 rawv6_sendmsg+0x2fcb/0x41a0 net/ipv6/raw.c:919
 inet_sendmsg+0x3f8/0x6d0 net/ipv4/af_inet.c:762
 sock_sendmsg_nosec net/socket.c:633
 sock_sendmsg net/socket.c:643
 SYSC_sendto+0x6a5/0x7c0 net/socket.c:1696
 SyS_sendto+0xbc/0xe0 net/socket.c:1664
 do_syscall_64+0x72/0xa0 arch/x86/entry/common.c:285
 entry_SYSCALL64_slow_path+0x25/0x25 arch/x86/entry/entry_64.S:246
RIP: 0033:0x436e03
RSP: 002b:00007ffce48baf38 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 00000000004002b0 RCX: 0000000000436e03
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000003
RBP: 00007ffce48baf90 R08: 00007ffce48baf50 R09: 000000000000001c
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 0000000000401790 R14: 0000000000401820 R15: 0000000000000000
origin: 00000000d9400053
 save_stack_trace+0x16/0x20 arch/x86/kernel/stacktrace.c:59
 kmsan_save_stack_with_flags mm/kmsan/kmsan.c:362
 kmsan_internal_poison_shadow+0xb1/0x1a0 mm/kmsan/kmsan.c:257
 kmsan_poison_shadow+0x6d/0xc0 mm/kmsan/kmsan.c:270
 slab_alloc_node mm/slub.c:2735
 __kmalloc_node_track_caller+0x1f4/0x390 mm/slub.c:4341
 __kmalloc_reserve net/core/skbuff.c:138
 __alloc_skb+0x2cd/0x740 net/core/skbuff.c:231
 alloc_skb ./include/linux/skbuff.h:933
 alloc_skb_with_frags+0x209/0xbc0 net/core/skbuff.c:4678
 sock_alloc_send_pskb+0x9ff/0xe00 net/core/sock.c:1903
 sock_alloc_send_skb+0xe4/0x100 net/core/sock.c:1920
 rawv6_send_hdrinc net/ipv6/raw.c:638
 rawv6_sendmsg+0x2918/0x41a0 net/ipv6/raw.c:919
 inet_sendmsg+0x3f8/0x6d0 net/ipv4/af_inet.c:762
 sock_sendmsg_nosec net/socket.c:633
 sock_sendmsg net/socket.c:643
 SYSC_sendto+0x6a5/0x7c0 net/socket.c:1696
 SyS_sendto+0xbc/0xe0 net/socket.c:1664
 do_syscall_64+0x72/0xa0 arch/x86/entry/common.c:285
 return_from_SYSCALL_64+0x0/0x6a arch/x86/entry/entry_64.S:246
==================================================================

, triggered by the following syscalls:
  socket(PF_INET6, SOCK_RAW, IPPROTO_RAW) = 3
  sendto(3, NULL, 0, 0, {sa_family=AF_INET6, sin6_port=htons(0), inet_pton(AF_INET6, "ff00::", &sin6_addr), sin6_flowinfo=0, sin6_scope_id=0}, 28) = -1 EPERM

A similar report is triggered in net/ipv4/raw.c if we use a PF_INET socket
instead of a PF_INET6 one.
Signed-off-by: Alexander Potapenko <glider@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>