Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp_rmem and tcp_wmem use 1 page as default value for the minimum
amount of memory to be used, same as udp_wmem_min and udp_rmem_min.
Pages are different size on different architectures - use the right
units when describing the defaults.
Reviewed-by: Shan Wei <shanwei@cn.fujitsu.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Max Matveev <makc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp does not use second and third ("default" and "max") values
of sctp_rmem tunable. The format is the same as tcp_rmem
but the meaning is different so make the documentation explicit to
avoid confusion.

sctp_wmem is not used at all.
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Max Matveev <makc@redhat.com>
Reviewed-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

b44_tx() is run from softirq handler, it can use dev_kfree_skb() instead
of dev_kfree_skb_irq()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

CCID-2's cwnd increases like TCP during slow-start, which has implications for
 * the local Sequence Window value (should be > cwnd),
 * the Ack Ratio value.
Hence an exponential growth, if it does not reflect the actual network
conditions, can quickly lead to instability.

This patch adds congestion-window validation (RFC2861) to CCID-2:
 * cwnd is constrained if the sender is application limited;
 * cwnd is reduced after a long idle period, as suggested in the '90 paper
   by Van Jacobson, in RFC 2581 (sec. 4.1);
 * cwnd is never reduced below the RFC 3390 initial window.

As marked in the comments, the code is actually almost a direct copy of the
TCP congestion-window-validation algorithms. By continuing this work, it may
in future be possible to use the TCP code (not possible at the moment).

The mechanism can be turned off using a module parameter. Sampling of the
currently-used window (moving-maximum) is however done constantly; this is
used to determine the expected window, which can be exploited to regulate
DCCP's Sequence Window value.

This patch also sets slow-start-after-idle (RFC 4341, 5.1), i.e. it behaves like
TCP when net.ipv4.tcp_slow_start_after_idle = 1.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>

This replaces a switch statement with a test, using the equivalent
function dccp_data_packet(skb).  It also doubles the range of the field
`rx_num_data_pkts' by changing the type from `int' to `u32', avoiding
signed/unsigned comparison with the u16 field `dccps_r_ack_ratio'.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>

This moves CCID-2's initial window function into the header file, since several
parts throughout the CCID-2 code need to call it (CCID-2 still uses RFC 3390).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Leandro Melo de Sales <leandro@ic.ufal.br>

Change the CCID (de)activation message to start with the
protocol name, as 'CCID' is already in there.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>

Realising the following call pattern,
 * first dccp_entail() is called to enqueue a new skb and
 * then skb_clone() is called to transmit a clone of that skb,
this patch integrates both into the same function.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>

This patch rearranges the order of statements of the slow-path input processing
(i.e. any other state than OPEN), to resolve the following issues.

 1. Dependencies: the order of statements now better matches RFC 4340, 8.5, i.e.
    step 7 is before step 9 (previously 9 was before 7), and parsing options in
    step 8 (which may consume resources) now comes after step 7.
 2. Sequence number checks are omitted if in state LISTEN/REQUEST, due to the
    note underneath the table in RFC 4340, 7.5.3.
    As a result, CCID processing is now indeed confined to OPEN/PARTOPEN states,
    i.e. congestion control is performed only on the flow of data packets. This
    avoids pathological cases of doing congestion control on those messages
    which set up and terminate the connection.
 3. Packets are now passed on to Ack Vector / CCID processing only after
    - step 7  (receive unexpected packets),
    - step 9  (receive Reset),
    - step 13 (receive CloseReq),
    - step 14 (receive Close)
    and only if the state is PARTOPEN. This simplifies CCID processing:
    - in LISTEN/CLOSED the CCIDs are non-existent;
    - in RESPOND/REQUEST the CCIDs have not yet been negotiated;
    - in CLOSEREQ and active-CLOSING the node has already closed this socket;
    - in passive-CLOSING the client is waiting for its Reset.
    In the last case, RFC 4340, 8.3 leaves it open to ignore further incoming
    data, which is the approach taken here.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>

It is a function of SuperH architecture. There is no good to use
the function on a driver generally. So, the driver uses
dma_map_single() instead of __flush_purge_region.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use pr_fmt() without KBUILD_MODNAME to allow AUN and econet prefixes.
Convert printks with KERN_DEBUG to pr_debug.
Hoist assigns from if.
80 column wrapping.
Move open braces to end of line.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Too trivial to live.

cc: WANG Cong <amwang@redhat.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Unused symbols waste space.

Commit 0e34e931
"(netpoll: add generic support for bridge and bonding devices)"
added the symbol more than a year ago with the promise of "future use".

Because it is so far unused, remove it for now.
It can be easily readded if or when it actually needs to be used.

cc: WANG Cong <amwang@redhat.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Correct the syntax so that both array and pointer are const.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make the case labels the same indent as the switch.

git diff -w shows 80 column line reflowing.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make the case labels the same indent as the switch.

git diff -w shows 80 column line reflowing.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make the case labels the same indent as the switch.

git diff -w shows useless break;s removed after returns
and a comment added to an unnecessary default: break;
because of a dubious gcc warning.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make the case labels the same indent as the switch.

git diff -w shows code on same line as case moved
to separate lines and a "/* Fallthrough */" comment
added where appropriate.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make the case labels the same indent as the switch.

git diff -w shows 80 column reflowing.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make the case labels the same indent as the switch.

git diff -w shows 80 column reflowing,
removal of a useless break after return, and moving
open brace after case instead of separate line.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make the case labels the same indent as the switch.

git diff -w shows no difference.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make the case labels the same indent as the switch.

git diff -w shows miscellaneous 80 column wrapping,
comment reflowing and a comment for a useless gcc
warning for an otherwise unused default: case.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make the case labels the same indent as the switch.

git diff -w shows miscellaneous 80 column wrapping.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make the case labels the same indent as the switch.

Simplify a default case / return (unreached)
Remove unnecessary break after return.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make the case labels the same indent as the switch.

git diff -w shows differences for line wrapping.
(fit multiple lines to 80 columns, join where possible)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make the case labels the same indent as the switch.

(git diff -w net/appletalk shows no difference)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a change sequence counter to each net namespace
which is bumped whenever a netdevice is added or removed from
the list. If such a change occurred while a link dump took place,
the dump will have the NLM_F_DUMP_INTR flag set in the first
message which has been interrupted and in all subsequent messages
of the same dump.

Note that links may still be modified or renamed while a dump is
taking place but we can guarantee for userspace to receive a
complete list of links and not miss any.

Testing:
I have added 500 VLAN netdevices to make sure the dump is split
over multiple messages. Then while continuously dumping links in
one process I also continuously deleted and re-added a dummy
netdevice in another process. Multiple dumps per seconds have
had the NLM_F_DUMP_INTR flag set.

I guess we can wait for Johannes patch to hit net-next via the
wireless tree.  I just wanted to give this some testing right away.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to check for the address being a multicast address in
the netdev_for_each_mc_addr loop, so remove it.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

It may be set in the card while the driver is probed by kdump kernel after a
crash.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On some skews, the BE card sends pause frames (and not drop pkts) if there are
no more posted buffers available for packet reception.  This behaviour has a
side effect: When an interface is disabled, buffers are no longer posted on the
corresponding RX rings. All broadcast and multicast traffic being received on
the port will quickly fill up the PMEM and cause pause push back. As the PMEM
is shared by both the ports, all traffic being received on the other (enabled)
port also gets stalled.
The fix is to destroy RX rings when the interface is disabled. If there is no
RX ring match in the RXF lookup, the packets are discarded and so don't hog the
PMEM.
The RXQ creation cmd must now use MCC instead of MBOX as they are are called
post MCC queue creation.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some (older)versions of cards/fw may not recognize certain cmds and
return illegal/unsupported errors. As long as the driver can handle
this gracefully there is no need to log an error msg.
Also finetuned 2 existing error log messages.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Add external loopback test in self test:
  - Send set external loopback mode request to fw.
     To quiscent other storage functions.
  - Perform test
  - Send unset loopback mode request to fw.

o Rename ilb to lb.
o Update driver version 5.0.20.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

External loopback test can be performed by application without any driver
support on normal Ethernet cards.
But on CNA devices, where multiple functions share same physical port.
Here internal loopback test and external loopback test can be initiated by
multiple functions at same time. To co exist all functions, firmware need
to regulate what test can be run by which function. So before performing external
loopback test, command need to send to firmware, which will quiescent other functions.

User may not want to run external loopback test always. As special cable need to be
connected for this test.
So adding explicit flag in ethtool self test, which will specify interface
to perform external loopback test.
 ETH_TEST_FL_EXTERNAL_LB: Application set to request external loopback test
 ETH_TEST_FL_EXTERNAL_LB_DONE: Driver ack if test performed
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to check for the address being a multicast address in
the netdev_for_each_mc_addr loop, so remove it.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>