commit a772d473 upstream.

When X11 is running and the user switches back to console, the card
modifies the content of registers M_MACCESS and M_PITCH in periodic
intervals.

This patch fixes it by restoring the content of these registers before
issuing any accelerator command.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit b6ccb980 upstream.

CPU_32v6 currently selects CPU_USE_DOMAINS if CPU_V6 and MMU. This is
because ARM 1136 r0pX CPUs lack the v6k extensions, and therefore do
not have hardware thread registers. The lack of these registers requires
the kernel to update the vectors page at each context switch in order to
write a new TLS pointer. This write must be done via the userspace
mapping, since aliasing caches can lead to expensive flushing when using
kmap. Finally, this requires the vectors page to be mapped r/w for
kernel and r/o for user, which has implications for things like put_user
which must trigger CoW appropriately when targetting user pages.

The upshot of all this is that a v6/v7 kernel makes use of domains to
segregate kernel and user memory accesses. This has the nasty
side-effect of making device mappings executable, which has been
observed to cause subtle bugs on recent cores (e.g. Cortex-A15
performing a speculative instruction fetch from the GIC and acking an
interrupt in the process).

This patch solves this problem by removing the remaining domain support
from ARMv6. A new memory type is added specifically for the vectors page
which allows that page (and only that page) to be mapped as user r/o,
kernel r/w. All other user r/o pages are mapped also as kernel r/o.
Patch co-developed with Russell King.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[bwh: Backported to 3.2:
 - Adjust filename, context
 - Drop condition on CONFIG_ARM_LPAE]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 26ffd0d4 upstream.

PROT_NONE mappings apply the page protection attributes defined by _P000
which translate to PAGE_NONE for ARM. These attributes specify an XN,
RDONLY pte that is inaccessible to userspace. However, on kernels
configured without support for domains, such a pte *is* accessible to
the kernel and can be read via get_user, allowing tasks to read
PROT_NONE pages via syscalls such as read/write over a pipe.

This patch introduces a new software pte flag, L_PTE_NONE, that is set
to identify faulting, present entries.
Signed-off-by: Will Deacon <will.deacon@arm.com>
[bwh: Backported to 3.2 as dependency of commit b6ccb980
 ('ARM: 7954/1: mm: remove remaining domain support from ARMv6'):
 - Drop 3-level changes
 - Adjust filename, context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 6b355b33 upstream.

Previous logic,
if (avail > 8) {
	store slave;
	return;
}
send data; clear;

The logic error is, if there isn't space send the buffer and clear,
but the slave wasn't added to the now empty buffer loosing that slave
id.  It also should have been "if (avail >= 8)" because when it is 8,
there is space.

Instead, if there isn't space send and clear the buffer, then there is
always space for the slave id.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 0f540c3a upstream.

Since
commit ee1452d7
Author: Jani Nikula <jani.nikula@intel.com>
Date:   Fri Sep 20 15:05:30 2013 +0300

    drm/i915: assume all GM45 Acer laptops use inverted backlight PWM

failed and was later reverted in
commit be505f64
Author: Alexander van Heukelum <heukelum@fastmail.fm>
Date:   Sat Dec 28 21:00:39 2013 +0100

    Revert "drm/i915: assume all GM45 Acer laptops use inverted backlight PWM"

fix the individual broken machine instead.

Note to backporters:

http://patchwork.freedesktop.org/patch/17837/

is the patch you want for 3.13 and older.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=54171
Reference: http://mid.gmane.org/DUB115-W7628C7C710EA51AA110CD4A5000@phx.gblSigned-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Patch mangling for 3.14 plus adding the link to the original
for 3.13.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit ac4199e0 upstream.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=53881
Cc: Jani Nikula <jani.nikula@intel.com>
Tested-by: Jani Monoses <jani@ubuntu.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit c88507fb upstream.

DST_NOCOUNT should only be used if an authorized user adds routes
locally. In case of routes which are added on behalf of router
advertisments this flag must not get used as it allows an unlimited
number of routes getting added remotely.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust context]
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit 1535bd8a ]

When checking a system call return code for an error,
linux_sparc_syscall was sign-extending the lower 32-bit value and
comparing it to -ERESTART_RESTARTBLOCK. lseek can return valid return
codes whose lower 32-bits alone would indicate a failure (such as 4G-1).
Use the whole 64-bit value to check for errors. Only the 32-bit path
should sign extend the lower 32-bit value.
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Acked-by: Bob Picco <bob.picco@oracle.com>
Acked-by: Allen Pais <allen.pais@oracle.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit 4f6500ff ]

In arch/sparc/Kernel/Makefile, we see:

   obj-$(CONFIG_SPARC64)   += jump_label.o

However, the Kconfig selects HAVE_ARCH_JUMP_LABEL unconditionally
for all SPARC.  This in turn leads to the following failure when
doing allmodconfig coverage builds:

kernel/built-in.o: In function `__jump_label_update':
jump_label.c:(.text+0x8560c): undefined reference to `arch_jump_label_transform'
kernel/built-in.o: In function `arch_jump_label_transform_static':
(.text+0x85cf4): undefined reference to `arch_jump_label_transform'
make: *** [vmlinux] Error 1

Change HAVE_ARCH_JUMP_LABEL to be conditional on SPARC64 so that it
matches the Makefile.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit 16932237 ]

This reverts commit 145e1c00.

This commit broke the behavior of __copy_from_user_inatomic when
it is only partially successful. Instead of returning the number
of bytes not copied, it now returns 1. This translates to the
wrong value being returned by iov_iter_copy_from_user_atomic.

xfstests generic/246 and LTP writev01 both fail on btrfs and nfs
because of this.
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit 557fc587 ]

The SIMBA APB Bridges lacks the 'ranges' of-property describing the
PCI I/O and memory areas located beneath the bridge. Faking this
information has been performed by reading range registers in the
APB bridge, and calculating the corresponding areas.

In commit 01f94c4a
("Fix sabre pci controllers with new probing scheme.") a bug was
introduced into this calculation, causing the PCI memory areas
to be calculated incorrectly: The shift size was set to be
identical for I/O and MEM ranges, which is incorrect.

This patch set the shift size of the MEM range back to the
value used before 01f94c4a.
Signed-off-by: Kjetil Oftedal <oftedal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit bf39b424 ]

Binding might result in a NULL device which is later dereferenced
without checking.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit 7563487c ]

There are three buffer overflows addressed in this patch.

1) In isdnloop_fake_err() we add an 'E' to a 60 character string and
then copy it into a 60 character buffer.  I have made the destination
buffer 64 characters and I'm changed the sprintf() to a snprintf().

2) In isdnloop_parse_cmd(), p points to a 6 characters into a 60
character buffer so we have 54 characters.  The ->eazlist[] is 11
characters long.  I have modified the code to return if the source
buffer is too long.

3) In isdnloop_command() the cbuf[] array was 60 characters long but the
max length of the string then can be up to 79 characters.  I made the
cbuf array 80 characters long and changed the sprintf() to snprintf().
I also removed the temporary "dial" buffer and changed it to use "p"
directly.

Unfortunately, we pass the "cbuf" string from isdnloop_command() to
isdnloop_writecmd() which truncates anything over 60 characters to make
it fit in card->omsg[].  (It can accept values up to 255 characters so
long as there is a '\n' character every 60 characters).  For now I have
just fixed the memory corruption bug and left the other problems in this
driver alone.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit 77bc6bed ]

Return -EINVAL unless all of user-given strings are correctly
NUL-terminated.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit 8b7b9324 ]

nla_strcmp compares the string length plus one, so it's implicitly
including the nul-termination in the comparison.

 int nla_strcmp(const struct nlattr *nla, const char *str)
 {
        int len = strlen(str) + 1;
        ...
                d = memcmp(nla_data(nla), str, len);

However, if NLA_STRING is used, userspace can send us a string without
the nul-termination. This is a problem since the string
comparison will not match as the last byte may be not the
nul-termination.

Fix this by skipping the comparison of the nul-termination if the
attribute data is nul-terminated. Suggested by Thomas Graf.

Cc: Florian Westphal <fw@strlen.de>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit 43a43b60 ]

After commit c15b1cca ("ipv6: move DAD and addrconf_verify
processing to workqueue") some counters are now updated in process context
and thus need to disable bh before doing so, otherwise deadlocks can
happen on 32-bit archs. Fabio Estevam noticed this while while mounting
a NFS volume on an ARM board.

As a compensation for missing this I looked after the other *_STATS_BH
and found three other calls which need updating:

1) icmp6_send: ip6_fragment -> icmpv6_send -> icmp6_send (error handling)
2) ip6_push_pending_frames: rawv6_sendmsg -> rawv6_push_pending_frames -> ...
   (only in case of icmp protocol with raw sockets in error handling)
3) ping6_v6_sendmsg (error handling)

Fixes: c15b1cca ("ipv6: move DAD and addrconf_verify processing to workqueue")
Reported-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit 0576eddf ]

This patch removes a test in start_new_rx_buffer() that checks whether
a copy operation is less than MAX_BUFFER_OFFSET in length, since
MAX_BUFFER_OFFSET is defined to be PAGE_SIZE and the only caller of
start_new_rx_buffer() already limits copy operations to PAGE_SIZE or less.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Reported-By: Sander Eikelenboom <linux@eikelenboom.it>
Tested-By: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit a39ee449 ]

vhost fails to validate negative error code
from vhost_get_vq_desc causing
a crash: we are using -EFAULT which is 0xfffffff2
as vector size, which exceeds the allocated size.

The code in question was introduced in commit
8dd014ad
    vhost-net: mergeable buffers support

CVE-2014-0055
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit d8316f39 ]

When mergeable buffers are disabled, and the
incoming packet is too large for the rx buffer,
get_rx_bufs returns success.

This was intentional in order for make recvmsg
truncate the packet and then handle_rx would
detect err != sock_len and drop it.

Unfortunately we pass the original sock_len to
recvmsg - which means we use parts of iov not fully
validated.

Fix this up by detecting this overrun and doing packet drop
immediately.

CVE-2014-0077
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit e367c2d0 ]

In ip6_append_data_mtu(), when the xfrm mode is not tunnel(such as
transport),the ipsec header need to be added in the first fragment, so the mtu
will decrease to reserve space for it, then the second fragment come, the mtu
should be turn back, as the commit 0c183379
said.  however, in the commit a493e60ac4bbe2e977e7129d6d8cbb0dd236be, it use
*mtu = min(*mtu, ...) to change the mtu, which lead to the new mtu is alway
equal with the first fragment's. and cannot turn back.

when I test through  ping6 -c1 -s5000 $ip (mtu=1280):
...frag (0|1232) ESP(spi=0x00002000,seq=0xb), length 1232
...frag (1232|1216)
...frag (2448|1216)
...frag (3664|1216)
...frag (4880|164)

which should be:
...frag (0|1232) ESP(spi=0x00001000,seq=0x1), length 1232
...frag (1232|1232)
...frag (2464|1232)
...frag (3696|1232)
...frag (4928|116)

so delete the min() when change back the mtu.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Fixes: 75a493e6 ("ipv6: ip6_append_data_mtu did not care about pmtudisc and frag_size")
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit ecab6701 ]

tmp_prefered_lft is an offset to ifp->tstamp, not now. Therefore
age needs to be added to the condition.

Age calculation in ipv6_create_tempaddr is different from the one
in addrconf_verify and doesn't consider ADDRCONF_TIMER_FUZZ_MINUS.
This can cause age in ipv6_create_tempaddr to be less than the one
in addrconf_verify and therefore unnecessary temporary address to
be generated.
Use age calculation as in addrconf_modify to avoid this.
Signed-off-by: Heiner Kallweit <heiner.kallweit@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit dbb490b9 ]

When copying in a struct msghdr from the user, if the user has set the
msg_namelen parameter to a negative value it gets clamped to a valid
size due to a comparison between signed and unsigned values.

Ensure the syscall errors when the user passes in a negative value.
Signed-off-by: Matthew Leach <matthew.leach@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit dd38743b ]

With TX VLAN offload enabled the source MAC address for frames sent using the
VLAN interface is currently set to the address of the real interface. This is
wrong since the VLAN interface may be configured with a different address.

The bug was introduced in commit 2205369a
("vlan: Fix header ops passthru when doing TX VLAN offload.").

This patch sets the source address before calling the create function of the
real interface.
Signed-off-by: Peter Boström <peter.bostrom@netrounds.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit de144391 ]

Some applications didn't expect recvmsg() on a non blocking socket
could return -EINTR. This possibility was added as a side effect
of commit b3ca9b02 ("net: fix multithreaded signal handling in
unix recv routines").

To hit this bug, you need to be a bit unlucky, as the u->readlock
mutex is usually held for very small periods.

Fixes: b3ca9b02 ("net: fix multithreaded signal handling in unix recv routines")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Rainer Weikusat <rweikusat@mobileactivedefense.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit 6565b9ee ]

MLD queries are supposed to have an IPv6 link-local source address
according to RFC2710, section 4 and RFC3810, section 5.1.14. This patch
adds a sanity check to ignore such broken MLD queries.

Without this check, such malformed MLD queries can result in a
denial of service: The queries are ignored by any MLD listener
therefore they will not respond with an MLD report. However,
without this patch these malformed MLD queries would enable the
snooping part in the bridge code, potentially shutting down the
according ports towards these hosts for multicast traffic as the
bridge did not learn about these listeners.
Reported-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit c485658b ]

While working on ec0223ec ("net: sctp: fix sctp_sf_do_5_1D_ce to
verify if we/peer is AUTH capable"), we noticed that there's a skb
memory leakage in the error path.

Running the same reproducer as in ec0223ec and by unconditionally
jumping to the error label (to simulate an error condition) in
sctp_sf_do_5_1D_ce() receive path lets kmemleak detector bark about
the unfreed chunk->auth_chunk skb clone:

Unreferenced object 0xffff8800b8f3a000 (size 256):
  comm "softirq", pid 0, jiffies 4294769856 (age 110.757s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    89 ab 75 5e d4 01 58 13 00 00 00 00 00 00 00 00  ..u^..X.........
  backtrace:
    [<ffffffff816660be>] kmemleak_alloc+0x4e/0xb0
    [<ffffffff8119f328>] kmem_cache_alloc+0xc8/0x210
    [<ffffffff81566929>] skb_clone+0x49/0xb0
    [<ffffffffa0467459>] sctp_endpoint_bh_rcv+0x1d9/0x230 [sctp]
    [<ffffffffa046fdbc>] sctp_inq_push+0x4c/0x70 [sctp]
    [<ffffffffa047e8de>] sctp_rcv+0x82e/0x9a0 [sctp]
    [<ffffffff815abd38>] ip_local_deliver_finish+0xa8/0x210
    [<ffffffff815a64af>] nf_reinject+0xbf/0x180
    [<ffffffffa04b4762>] nfqnl_recv_verdict+0x1d2/0x2b0 [nfnetlink_queue]
    [<ffffffffa04aa40b>] nfnetlink_rcv_msg+0x14b/0x250 [nfnetlink]
    [<ffffffff815a3269>] netlink_rcv_skb+0xa9/0xc0
    [<ffffffffa04aa7cf>] nfnetlink_rcv+0x23f/0x408 [nfnetlink]
    [<ffffffff815a2bd8>] netlink_unicast+0x168/0x250
    [<ffffffff815a2fa1>] netlink_sendmsg+0x2e1/0x3f0
    [<ffffffff8155cc6b>] sock_sendmsg+0x8b/0xc0
    [<ffffffff8155d449>] ___sys_sendmsg+0x369/0x380

What happens is that commit bbd0d598 clones the skb containing
the AUTH chunk in sctp_endpoint_bh_rcv() when having the edge case
that an endpoint requires COOKIE-ECHO chunks to be authenticated:

  ---------- INIT[RANDOM; CHUNKS; HMAC-ALGO] ---------->
  <------- INIT-ACK[RANDOM; CHUNKS; HMAC-ALGO] ---------
  ------------------ AUTH; COOKIE-ECHO ---------------->
  <-------------------- COOKIE-ACK ---------------------

When we enter sctp_sf_do_5_1D_ce() and before we actually get to
the point where we process (and subsequently free) a non-NULL
chunk->auth_chunk, we could hit the "goto nomem_init" path from
an error condition and thus leave the cloned skb around w/o
freeing it.

The fix is to centrally free such clones in sctp_chunk_destroy()
handler that is invoked from sctp_chunk_free() after all refs have
dropped; and also move both kfree_skb(chunk->auth_chunk) there,
so that chunk->auth_chunk is either NULL (since sctp_chunkify()
allocs new chunks through kmem_cache_zalloc()) or non-NULL with
a valid skb pointer. chunk->skb and chunk->auth_chunk are the
only skbs in the sctp_chunk structure that need to be handeled.

While at it, we should use consume_skb() for both. It is the same
as dev_kfree_skb() but more appropriately named as we are not
a device but a protocol. Also, this effectively replaces the
kfree_skb() from both invocations into consume_skb(). Functions
are the same only that kfree_skb() assumes that the frame was
being dropped after a failure (e.g. for tools like drop monitor),
usage of consume_skb() seems more appropriate in function
sctp_chunk_destroy() though.

Fixes: bbd0d598 ("[SCTP]: Implement the receive and verification of AUTH chunk")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Vlad Yasevich <yasevich@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 8d7f6690 upstream.

The kernel currently crashes with a low-address-protection exception
if a user space process executes an instruction that tries to use the
linkage stack. Set the base-ASTE origin and the subspace-ASTE origin
of the dispatchable-unit-control-table to point to a dummy ASTE.
Set up control register 15 to point to an empty linkage stack with no
room left.

A user space process with a linkage stack instruction will still crash
but with a different exception which is correctly translated to a
segmentation fault instead of a kernel oops.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 5d81de8e upstream.

It's possible for userland to pass down an iovec via writev() that has a
bogus user pointer in it. If that happens and we're doing an uncached
write, then we can end up getting less bytes than we expect from the
call to iov_iter_copy_from_user. This is CVE-2014-0069

cifs_iovec_write isn't set up to handle that situation however. It'll
blindly keep chugging through the page array and not filling those pages
with anything useful. Worse yet, we'll later end up with a negative
number in wdata->tailsz, which will confuse the sending routines and
cause an oops at the very least.

Fix this by having the copy phase of cifs_iovec_write stop copying data
in this situation and send the last write as a short one. At the same
time, we want to avoid sending a zero-length write to the server, so
break out of the loop and set rc to -EFAULT if that happens. This also
allows us to handle the case where no address in the iovec is valid.

[Note: Marking this for stable on v3.4+ kernels, but kernels as old as
       v2.6.38 may have a similar problem and may need similar fix]
Reviewed-by: Pavel Shilovsky <piastry@etersoft.ru>
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
[bwh: Backported to 3.2:
 - Adjust context
 - s/nr_pages/npages/
 - s/wdata->pages/pages/
 - In case of an error with no data copied, we must kunmap() page 0,
   but in neither case should we free anything else]
 Thanks to Raphael Geissert for an independent backport that showed some
 bugs in my first version.]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 26a865f4 upstream.

After free_loaded_vmcs executes, the "loaded_vmcs" structure
is kfreed, and now vmx->loaded_vmcs points to a kfreed area.
Subsequent free_loaded_vmcs then attempts to manipulate
vmx->loaded_vmcs.

Switch the order to avoid the problem.

https://bugzilla.redhat.com/show_bug.cgi?id=1047892Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 989c6b34 upstream.

It is possible for __direct_map to be called on invalid root_hpa
(-1), two examples:

1) try_async_pf -> can_do_async_pf
    -> vmx_interrupt_allowed -> nested_vmx_vmexit
2) vmx_handle_exit -> vmx_interrupt_allowed -> nested_vmx_vmexit

Then to load_vmcs12_host_state and kvm_mmu_reset_context.

Check for this possibility, let fault exception be regenerated.

BZ: https://bugzilla.redhat.com/show_bug.cgi?id=924916Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit d43ff4cd upstream.

The struct driver_info ax88178_info is assigned the function
asix_rx_fixup_common as it's rx_fixup callback. This means that
FLAG_MULTI_PACKET must be set as this function is cloning the
data and calling usbnet_skb_return. Not setting this flag leads
to usbnet_skb_return beeing called a second time from within
the rx_process function in the usbnet module.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 8b5b6f54 upstream.

ASIX AX88772B started to pack data even more tightly. Packets and the ASIX packet
header may now cross URB boundaries. To handle this we have to introduce
some state between individual calls to asix_rx_fixup().
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ Emil: backported to 3.2:
 - dropped changes to drivers/net/usb/ax88172a.c 
 - Introduced some static function declarations as the functions
   are not used outside of asix.c (sparse is complaining about it) ]
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit a9e0aca4 upstream.

asix_rx_fixup() is complex, and does some unnecessary memory copies (at
least on x86 where NET_IP_ALIGN is 0)

Also, it tends to provide skbs with a big truesize (4096+256 with
MTU=1500) to upper stack, so incoming trafic consume a lot of memory and
I noticed early packet drops because we hit socket rcvbuf too fast.

Switch to a different strategy, using copybreak so that we provide nice
skbs to upper stack (including the NET_SKB_PAD to avoid future head
reallocations in some paths)

With this patch, I no longer see packets drops or tcp collapses on
various tcp workload with a AX88772 adapter.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Aurelien Jacobs <aurel@gnuage.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Trond Wuellner <trond@chromium.org>
Cc: Grant Grundler <grundler@chromium.org>
Cc: Paul Stewart <pstew@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ Emil: Backported to 3.2: fixed small conflict ]
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit f8ce239d upstream.

builddeb generates a control file that says the linux-headers package
can only be built for the build system primary architecture.  This
breaks cross-building configurations.  We should use $debarch for this
instead.

Since $debarch is not yet set when generating the control file, set
Architecture: any and use control file variables to fill in the
description.

Fixes: cd8d60a2 ('kbuild: create linux-headers package in deb-pkg')
Reported-and-tested-by: "Niew, Sh." <shniew@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Michal Marek <mmarek@suse.cz>

commit c5e318f6 upstream.

These commands will mysteriously fail:

$ make ARCH=arm versatile_defconfig
[...]
$ make ARCH=arm deb-pkg
[...]
make[1]: *** [deb-pkg] Error 1
make: *** [deb-pkg] Error 2

The Debian architecture selection for these kernel architectures does
'grep FOO=y $KCONFIG_CONFIG && echo bar', and after 'set -e' this
aborts the script if grep does not find the given config symbol.

Fixes: 10f26fa6 ('build, deb-pkg: select userland architecture based on UTS_MACHINE')
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Michal Marek <mmarek@suse.cz>

commit d2091767 upstream.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Michal Marek <mmarek@suse.cz>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit fe6cc55f upstream.

[ use zero netdev_feature mask to avoid backport of
  netif_skb_dev_features function ]

Marcelo Ricardo Leitner reported problems when the forwarding link path
has a lower mtu than the incoming one if the inbound interface supports GRO.

Given:
Host <mtu1500> R1 <mtu1200> R2

Host sends tcp stream which is routed via R1 and R2.  R1 performs GRO.

In this case, the kernel will fail to send ICMP fragmentation needed
messages (or pkt too big for ipv6), as GSO packets currently bypass dstmtu
checks in forward path. Instead, Linux tries to send out packets exceeding
the mtu.

When locking route MTU on Host (i.e., no ipv4 DF bit set), R1 does
not fragment the packets when forwarding, and again tries to send out
packets exceeding R1-R2 link mtu.

This alters the forwarding dstmtu checks to take the individual gso
segment lengths into account.

For ipv6, we send out pkt too big error for gso if the individual
segments are too big.

For ipv4, we either send icmp fragmentation needed, or, if the DF bit
is not set, perform software segmentation and let the output path
create fragments when the packet is leaving the machine.
It is not 100% correct as the error message will contain the headers of
the GRO skb instead of the original/segmented one, but it seems to
work fine in my (limited) tests.

Eric Dumazet suggested to simply shrink mss via ->gso_size to avoid
sofware segmentation.

However it turns out that skb_segment() assumes skb nr_frags is related
to mss size so we would BUG there.  I don't want to mess with it considering
Herbert and Eric disagree on what the correct behavior should be.

Hannes Frederic Sowa notes that when we would shrink gso_size
skb_segment would then also need to deal with the case where
SKB_MAX_FRAGS would be exceeded.

This uses sofware segmentation in the forward path when we hit ipv4
non-DF packets and the outgoing link mtu is too small.  Its not perfect,
but given the lack of bug reports wrt. GRO fwd being broken this is a
rare case anyway.  Also its not like this could not be improved later
once the dust settles.
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Reported-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit de960aa9 upstream.

[ no skb_gso_seglen helper in 3.4, leave tbf alone ]

This moves part of Eric Dumazets skb_gso_seglen helper from tbf sched to
skbuff core so it may be reused by upcoming ip forwarding path patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

In older kernels (before v3.10) ipc_rcu_hdr->refcount was non-atomic int.
There was possuble double-free bug: do_msgsnd() calls ipc_rcu_putref() under
msq->q_perm->lock and RCU, while freequeue() calls it while it holds only
'rw_mutex', so there is no sinchronization between them. Two function
decrements '2' non-atomically, they both can get '0' as result.

do_msgsnd()					freequeue()

msq = msg_lock_check(ns, msqid);
...
ipc_rcu_getref(msq);
msg_unlock(msq);
schedule();
						(caller locks spinlock)
						expunge_all(msq, -EIDRM);
						ss_wakeup(&msq->q_senders, 1);
						msg_rmid(ns, msq);
						msg_unlock(msq);
ipc_lock_by_ptr(&msq->q_perm);
ipc_rcu_putref(msq);				ipc_rcu_putref(msq);
< both may get get --(...)->refcount == 0 >

This patch locks ipc_lock and RCU around ipc_rcu_putref in freequeue.
( RCU protects memory for spin_unlock() )

Similar bugs might be in other users of ipc_rcu_putref().

In the mainline this has been fixed in v3.10 indirectly in commmit
6062a8dc
("ipc,sem: fine grained locking for semtimedop") by Rik van Riel.
That commit optimized locking and converted refcount into atomic.

I'm not sure that anybody should care about this bug: it's very-very unlikely
and no longer exists in actual mainline. I've found this just by looking into
the code, probably this never happens in real life.
Signed-off-by: Konstantin Khlebnikov <k.khlebnikov@samsung.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>