Add DT for DH PicoITX unit, which is a bare-bones carrier board for
the DHCOM. The board has ethernet port, USB, CAN, LEDs and a custom
board-to-board expansion connector.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Document devicetree compatible strings of the DH SoMs and boards.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

The stm32mp1 TAMP peripheral has 32 backup registers that survive
a warm reset. This makes them suitable for storing a reboot
mode, which the vendor's kernel tree is already doing[0].

The actual syscon-reboot-mode child node can be added by a board.dts or
fixed up by the bootloader. For the child node to be probed, the
compatible needs to include simple-mfd. The binding now specifies this,
so have the SoC dtsi adhere to it.

[0]: https://github.com/STMicroelectronics/linux/commit/2e9bfc29ddSigned-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

The stm32mp1 TAMP (Tamper and backup registers) does tamper detection
and features 32 backup registers that, being in the RTC domain, may
survive even with Vdd switched off.

This makes it suitable for use to communicate a reboot mode from OS
to bootloader via the syscon-reboot-mode binding. Add a "simple-mfd"
to support probing such a child node. The actual reboot mode
node could then be defined in a board.dts or fixed up by the bootloader.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Two backup registers are used to store the Cortex-M4 state and the resource
table address.
Declare the tamp node and add associated properties in m4_rproc node
to allow Linux to attach to a firmware loaded by the first boot stages.

Associated driver implementation is available in commit 9276536f
("remoteproc: stm32: Parse syscon that will manage M4 synchronisation").
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Defaut use case on stm32mp151 USB OTG is ethernet gadget, using EP1 bulk
endpoint (MPS=512 bytes) and EP2 interrupt endpoint (MPS=16 bytes).
This patch optimizes USB OTG FIFO sizes accordingly.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Reg property length should cover all DMAMUX_CxCR registers.
DMAMUX_CxCR Address offset: 0x000 + 0x04 * x (x = 0 to 15), so latest
offset is at 0x3c, so length should be 0x40.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Reg property length should cover all DMAMUX_CxCR registers.
DMAMUX_CxCR Address offset: 0x000 + 0x04 * x (x = 0 to 15), so latest
offset is at 0x3c, so length should be 0x40.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Update mdma1 clients channel priority level following stm32-mdma bindings.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

This patch adds support for STUSB1600 USB Type-C port controller, used on
I2C4 on stm32mp15xx-dkx.
The default configuration on this board, on Type-C connector, is:
- Dual Power Role (DRP), so set power-role to "dual";
- Vbus limited to 500mA, so set typec-power-opmode to "default" (it means
  500mA in USB 2.0).
typec-power-opmode is used to reconfigure the STUSB1600 advertising of
current capability when its NVM is not in line with the board layout.
On stm32mp15xx-dkx, Vbus power source of STUSB1600 is 5V_VIN. So power
operation mode depends on the power supply used. To avoid any power
issues, it is better to limit Vbus to 500mA on this board.
ALERT# is the interrupt pin of STUSB1600. It needs an external pull-up, and
signal is active low.

USB OTG controller ID and Vbus signals are not connected on stm32mp15xx-dkx
boards, so disconnection are not detected.
Without DWC2 usb-role-switch:
- if you unplug the USB cable from the Type-C port, you have to manually
disconnect the USB gadget:
echo disconnect > /sys/devices/platform/soc/49000000.usb-otg/udc/49000000.usb-otg/soft_connect
- Then you can plug the USB cable again in the Type-C port, and manually
reconnect the USB gadget:
echo connect > /sys/devices/platform/soc/49000000.usb-otg/udc/49000000.usb-otg/soft_connect
With DWC2 usb-role-switch, USB gadget is dynamically disconnected or connected.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Add binding documentation for the STMicroelectronics STUSB160x Type-C port
controller.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Power operation mode may depends on hardware design, so, add the optional
property typec-power-opmode for usb-c connector to select the power
operation mode capability.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Move spi4 at the right alphabetical place within stm32mp15-pinctrl

Fixes: 4fe66389 ("ARM: dts: stm32: Fix spi4 pins in stm32mp15-pinctrl")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Explicitly set bus-type to parallel mode in DCMI endpoint (bus-type=5).
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Explicitly set bus-type to parallel mode in DCMI endpoint (bus-type=5).
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Enable CRYP1 device for cryp accelerated support on
stm32mp157C-EV1/DK2 STMicroelectronics platforms.
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Enable CRC1 device for CRC-32 accelerated support on
stm32mp15 STMicroelectronics platforms.
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Enable HASH1 device for HASH accelerated support on
stm32mp15 STMicroelectronics platforms.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

LP timer can be used to wakeup from stop mode on stm32mp151.
Add wakeup-source properties to all LP timer instances.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Add all LP timer irqs on stm32mp151.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Update the IP version to v2.0, which supports linked lists in internal DMA,
and is present in STM32MP1 SoCs.

The mmci driver supports the v2.0 periph id since 7a2a98be ("mmc: mmci:
Add support for sdmmc variant revision 2.0"), so it's now Ok to add it into
the SoC device tree to benefit from the improved DMA support.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

In accordance with the Generic EHCI/OHCI bindings the corresponding node
name is suppose to comply with the Generic USB HCD DT schema, which
requires the USB nodes to have the name acceptable by the regexp:
"^usb(@.*)?" . Make sure the "generic-ehci" and "generic-ohci"-compatible
nodes are correctly named.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Amelie Delaunay <amelie.delaunay@st.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Add bindings for the KS8851 ethernet present on the STM32MP1 DHCOM SoM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Add another mux option for FMC EBI bus, this is used on DHCOM SoM
for the second ethernet and on the PDK2 devkit for SRAM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

On the production DHCOM STM32MP15xx SoM, the PHY IRQ line is connected
to the PI11 pin. Describe it in the DT as well, so the PHY IRQ can be
used e.g. to detect cable insertion and removal.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Enable FIFO mode with half-full threshold.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

The VDDA LDO1 PMIC output supplies the analog VDDA input of the
STM32MP1 on DHCOM, keep it always on, otherwise there could be
leakage through the SoC.

Fixes: 34e0c784 ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Enable STM32 Digital Thermal Sensor driver for stm32mp15xx-dhcor SoMs.

Fixes: 94cafe1b ("ARM: dts: stm32: Add Avenger96 devicetree support based on STM32MP157A")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

The VIO regulator is supplied by PMIC Buck3, describe this in the DT.

Fixes: 34e0c784 ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

On the prototype DHCOM, the LED5 was connected to pin PG2 of the
STM32MP15xx, however on the production SoM this was changed to pin
PC6. Update the connection in the DT.

Fixes: 81d5fc71 ("ARM: dts: stm32: Add GPIO LEDs for STM32MP1 DHCOM PDK2")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

On the prototype DHCOM, the TA3-GPIO-C button was connected to pin PI11 of
the STM32MP15xx, however on the production SoM this was changed to pin PG0
to free up the IRQ line 11 for LAN8710i PHY IRQ. Update the connection in
the DT. Since the IRQ line 0 is used for PMIC as well and cannot be shared
with the button, make the button polled.

Fixes: 87cabf94 ("ARM: dts: stm32: Add GPIO keys for STM32MP1 DHCOM PDK2")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Add description for Vin power supply and for peripherals that
are supplied by Vin.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Add description for Vin power supply and for peripherals that
are supplied by Vin.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.

Remove the quote operator # from compiler_attributes.h __section macro.

Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.

Conversion done using the script at:

    https://lore.kernel.org/lkml/75393e5ddc272dc7403de74d645e6c6e0f4e70eb.camel@perches.com/2-convert_section.plSigned-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@gooogle.com>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

tid_addr is not a "pointer to (pointer to int in userspace)"; it is in
fact a "pointer to (pointer to int in userspace) in userspace".  So
sparse rightfully complains about passing a kernel pointer to
put_user().
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 453431a5 ("mm, treewide: rename kzfree() to
kfree_sensitive()") renamed kzfree() to kfree_sensitive(),
but it left a compatibility definition of kzfree() to avoid
being too disruptive.

Since then a few more instances of kzfree() have slipped in.

Just get rid of them and remove the compatibility definition
once and for all.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If set, use the environment variable GIT_DIR to change the default .git
location of the kernel git tree.

If GIT_DIR is unset, keep using the current ".git" default.

Link: https://lkml.kernel.org/r/c5e23b45562373d632fccb8bc04e563abba4dd1d.camel@perches.comSigned-off-by: Joe Perches <joe@perches.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull timer fixes from Thomas Gleixner:
 "A time namespace fix and a matching selftest. The futex absolute
  timeouts which are based on CLOCK_MONOTONIC require time namespace
  corrected. This was missed in the original time namesapce support"

* tag 'timers-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  selftests/timens: Add a test for futex()
  futex: Adjust absolute futex timeouts with per time namespace offset

Pull scheduler fixes from Thomas Gleixner:
 "Two scheduler fixes:

   - A trivial build fix for sched_feat() to compile correctly with
     CONFIG_JUMP_LABEL=n

   - Replace a zero lenght array with a flexible array"

* tag 'sched-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/features: Fix !CONFIG_JUMP_LABEL case
  sched: Replace zero-length array with flexible-array