- 13 Nov, 2019 37 commits
-
-
Bhawanpreet Lakha authored
[Why] DCN21 is stable enough to be build by default. So drop the flags. [How] Remove them using the unifdef tool. The following commands were executed in sequence: $ find -name '*.c' -exec unifdef -m -DCONFIG_DRM_AMD_DC_DCN2_1 -UCONFIG_TRIM_DRM_AMD_DC_DCN2_1 '{}' ';' $ find -name '*.h' -exec unifdef -m -DCONFIG_DRM_AMD_DC_DCN2_1 -UCONFIG_TRIM_DRM_AMD_DC_DCN2_1 '{}' ';' In addition: * Remove from kconfig, and replace any dependencies with DCN1_0. * Remove from any makefiles. * Fix and cleanup Renoir definitions in dal_asic_id.h * Expand DCN1 ifdef to include DCN21 code in the following files: * clk_mgr/clk_mgr.c: dc_clk_mgr_create() * core/dc_resources.c: dc_create_resource_pool() * gpio/hw_factory.c: dal_hw_factory_init() * gpio/hw_translate.c: dal_hw_translate_init() Signed-off-by:Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Reviewed-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Bhawanpreet Lakha authored
[Why] DCN2 and DSC are stable enough to be build by default. So drop the flags. [How] Remove them using the unifdef tool. The following commands were executed in sequence: $ find -name '*.c' -exec unifdef -m -DCONFIG_DRM_AMD_DC_DSC_SUPPORT -DCONFIG_DRM_AMD_DC_DCN2_0 -UCONFIG_TRIM_DRM_AMD_DC_DCN2_0 '{}' ';' $ find -name '*.h' -exec unifdef -m -DCONFIG_DRM_AMD_DC_DSC_SUPPORT -DCONFIG_DRM_AMD_DC_DCN2_0 -UCONFIG_TRIM_DRM_AMD_DC_DCN2_0 '{}' ';' In addition: * Remove from kconfig, and replace any dependencies with DCN1_0. * Remove from any makefiles. * Fix and cleanup NV defninitions in dal_asic_id.h * Expand DCN1 ifdef to include DCN2 code in the following files: * clk_mgr/clk_mgr.c: dc_clk_mgr_create() * core/dc_resources.c: dc_create_resource_pool() * dce/dce_dmcu.c: dcn20_*lock_phy() * dce/dce_dmcu.c: dcn20_funcs * dce/dce_dmcu.c: dcn20_dmcu_create() * gpio/hw_factory.c: dal_hw_factory_init() * gpio/hw_translate.c: dal_hw_translate_init() Signed-off-by:Leo Li <sunpeng.li@amd.com> Signed-off-by:
-
Leo Li authored
[Why] On DCN hardware, the crtc_high_irq handler makes vupdate_high_irq handler redundant. All the vupdate handler does is handle vblank events, and update vrr for DCE hw (excluding VEGA, more on that later). As far as usermode is concerned. vstartup happens close enough to vupdate on DCN that it can be considered the "same". Handling vblank and updating vrr at vstartup effectively replaces vupdate on DCN. Vega is a bit special. Like DCN, the VRR registers on Vega are double-buffered, and swapped at vupdate. But Unlike DCN, it lacks a vstartup interrupt. This means we can't quite remove the vupdate handler for it, since delayed user events due to vrr are sent off there. [How] Remove registration of vupdate interrupt handler for DCN. Disable vupdate interrupt if asic family DCN, enable otherwise. Reviewed-by:
Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by:
-
Leo Li authored
[Why] For DCN hardware, the crtc_high_irq handler is assigned to the vstartup interrupt. This is different from DCE, which has it assigned to vblank start. We'd like to send vblank and user events at vstartup because: * It happens close enough to vupdate - the point of no return for HW. * It is programmed as lines relative to vblank end - i.e. it is not in the variable portion when VRR is enabled. We should signal user events here. * The pflip interrupt responsible for sending user events today only fires if the DCH HUBP component is not clock gated. In situations where planes are disabled - but the CRTC is enabled - user events won't be sent out, leading to flip done timeouts. Consequently, this makes vupdate on DCN hardware redundant. It will be removed in the next change. [How] Add a DCN-specific crtc_high_irq handler, and hook it to the VStartup signal. Inside the DCN handler, we send off user events if the pflip handler hasn't already done so. Reviewed-by:
-
abdoulaye berthe authored
1-Read lttpr caps in 5-bytes 2-Parse caps 3-Validate caps and set lttpr_mode 4-Use hw default timeout when lttpr is disabled. Signed-off-by:
abdoulaye berthe <abdoulaye.berthe@amd.com> Reviewed-by:
Wenjing Liu <Wenjing.Liu@amd.com> Signed-off-by:
-
abdoulaye berthe authored
[Why] The aux timeout value is not default before reading link cap. Setting it to default when lttpr is not enabled causes some monitor not to light up. [How] Read the aux engine timeout value before setting it to extended. Set the aux engine timeout to its previous value if no lttpr. Signed-off-by:
Aric Cyr <Aric.Cyr@amd.com> Signed-off-by:
-
abdoulaye berthe authored
1-If at least one repeater is present in the link and we are in non transparent mode, perform clock recovery then channel equalization with all repeaters one by one before training DPRX. 2-Mark the end of LT with a repeater by setting training pattern 0 at the end of channel equalization with each repeater. Signed-off-by:
-
abdoulaye berthe authored
[Description] 1-Grant extended timeout request. Done once after detection 2-Configure lttpr mode based on lttpr support before LT 3-Account for lttpr cap when determining max link settings Signed-off-by:
-
abdoulaye berthe authored
[Why] LTTPR was introduced after DP1.2. Reading LTTPR registers 0xFXXXX on some DP 1.2 display is causing an unexpected behavior. [How] Make sure that we don't read any lttpr registers on 1.2 displays. Signed-off-by:
-
abdoulaye berthe authored
[Description] When reading link, update the procedure as follows: 1-Set aux timeout to extended: 3.2ms 2-Start with reading lttpr caps 3-Determine if lttpr support should be enabled. Reset aux timeout to 400us if no repeater is found. Signed-off-by:
-
Reza Amini authored
[why] We want to guarantee integer ratio scaling for all scaling modes. [how] Treat centered, fullscreen, preserve aspect ratio the same: scale the view as many times as possible, and fill in the rest with a black border. Signed-off-by:
Reza Amini <Reza.Amini@amd.com> Reviewed-by:
-
Jun Lei authored
[why] Need it for some OEM I2C devices in Nv10 [how] Link up code to parse OEM table and expose DC interface to access the pins Signed-off-by:
Jun Lei <Jun.Lei@amd.com> Reviewed-by:
-
Leo (Hanghong) Ma authored
[Why] For debug purpose, we need to check the following hardware status in DTN log debugfs: 1.dpp & hubp clock enable; 2.crtc blank enable; 3.link phy status; [How] Add the upper information in the amdgpu_dm_dtn_log debugfs. For CRTC blanked status, since DCN2 and greater reports it on the OPP instead of OTG, we patch it in after calling optc1_read_otg_states. Ideally, this should be done in the DCN version specific function hooks. It has been left as a TODO item. Signed-off-by:
Leo (Hanghong) Ma <hanghong.ma@amd.com> Reviewed-by:
Mikita Lipski <Mikita.Lipski@amd.com> Acked-by:
Harry Wentland <Harry.Wentland@amd.com> Signed-off-by:
-
Aric Cyr authored
Signed-off-by:
-
Yongqiang Sun authored
[Why] System is unable to enter S0i3 due to DISPLAY_OFF_MASK not asserted in SMU. [How] Optimized bandwidth should be called paired and to resolve unplug display underflow issue, optimize bandwidth after commit streams is moved to next page flip, in case of S0i3, there is a change for no flip coming causing display count is 1 in SMU side. Add optimize bandwidth after commit stream. Signed-off-by:
Yongqiang Sun <yongqiang.sun@amd.com> Reviewed-by:
Tony Cheng <Tony.Cheng@amd.com> Acked-by:
-
David Galiffi authored
[WHY] It has been a useful option in debugging GFXOFF and P.State Change issues. May be required as for platform specific workaround. [HOW] Create option in enum dc_debug_options, "disable_vactive_clock_change". When it is set, dm_dram_clock_change_vactive, will translate into p_state_change_support: false. Signed-off-by:
David Galiffi <David.Galiffi@amd.com> Reviewed-by:
-
Anthony Koo authored
[Why] It is confusing to sinks if we send VSC SDP only on some format. Today we signal colorimetry format using MSA while in formats like sRGB. But when we switch to BT2020 we set the bit to ignore MSA colorimetry and instead use the colorimetry information in the VSC SDP. But if sink supports signaling of colorimetry via VSC SDP we should always set the MSA MISC1 bit 6, instead of doing so selectively. [How] If sink supports signaling of colorimetry via VSC SDP, and we are sending the colorimetry info via VSC SDP with packet revision 05h, then always set MSA MISC1 bit 6. Signed-off-by:
Anthony Koo <Anthony.Koo@amd.com> Reviewed-by:
-
Nikola Cornij authored
[why] If acquire/release DSC resource sequence is affected by a regression, it can happen that the already-in-use DSC HW block is being wrongly re-used for a different pipe. The reverse is also possible, i.e. already-disabled DSC HW block could be disabled from other context. [how] Read back the enable state of DSC HW and report an error if duplicate enable or disable was attempted. Signed-off-by:
Nikola Cornij <nikola.cornij@amd.com> Reviewed-by:
Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Acked-by:
-
Sung Lee authored
[WHY] Currently made a change where disable_output is called using signal_type. Using actual signal_type when calilng disable_output in power_down_encoders would make DP to HDMI dongle not light up on boot. As it would have signal_type SIGNAL_TYPE_DISPLAY_PORT. [HOW] Set signal_type to SIGNAL_TYPE_NONE unless it is eDP. Signed-off-by:
Sung Lee <sung.lee@amd.com> Reviewed-by:
-
Eric Yang authored
[Why] For unknown reason, immediate flip with host VM translation on NV12 surface will underflow on last row of PTE. [How] Hack chroma viewport height to make fetch one more row of PTE. Note that this will cause hubp underflow on all video underlay cases, but the underflow is not user visible since it is in blank region. Signed-off-by:
Eric Yang <Eric.Yang2@amd.com> Reviewed-by:
-
David Galiffi authored
[WHY] V.Active dram clock change workaround need a small modification for DMLv2 to ensure that the dummy p-state check doesn't fail. Signed-off-by:
-
Aric Cyr authored
Signed-off-by:
-
Nicholas Kazlauskas authored
[Why] Support for DMUB only depends on support for DC. It doesn't use floating point so we don't need to guard it by any specific DCN revision. [How] Drop the guards and cleanup the newlines around each one. Signed-off-by:
Hersen Wu <hersenxs.wu@amd.com> Acked-by:
-
Nicholas Kazlauskas authored
[Why] DC can utilize the DMUB server to send commands to the DMUB but it's the DM responsibility to pass it the service to use. [How] Create the dc_dmub_srv after we finish initializing the dmub_srv. Cleanup the dc_dmub_srv before destroying the dmub_srv or dc. Signed-off-by:
-
Nicholas Kazlauskas authored
DC will use DMUB for command submission and flow control during initialization. Register offloading as well as submitting some BIOS commands are part of the DC internal interface but are guarded behind debug options. It won't be functional in amdgpu_dm yet since we don't pass the DMUB service to DC for use. Signed-off-by:
-
Nicholas Kazlauskas authored
The DMCUB firmware version can be read using the AMDGPU_INFO ioctl or the amdgpu_firmware_info debugfs entry. Signed-off-by:
-
Nicholas Kazlauskas authored
[Why] We need DMCUB on Renoir to support DMCU and PHY initialization. The DMUB service provides a mechanism to load the DMCUB. [How] Include the DMUB service in amdgpu_dm. Frontdoor loading of the DMCUB firmware needs to happen via PSP. To pass the firmware to PSP we need to hand it off to the firmware list in the base driver during software initialization. Most of the DMUB service can technically be initialized at this point in time, but we don't want to be allocating framebuffer memory for hardware that doesn't support the DMCUB and in order to check that we need to be able to read registers - something DM helpers aren't setup to do in software initialization. So everything but the service creation itself will get deferred to hardware initialization. Signed-off-by:
-
Yongqiang Sun authored
[Why] PSP version format is AB.CD.EF.GH, where CD and GH is the main version. current psp version check for dmcub loading dmcu check 0x00110029, in case of some psp version eg: 0x00110227 which main version should be 0x00110027, will result in unexpeceted dmcub loading dmcu FW. [How] Add psp version mask 0x00FF00FF for checking version. Signed-off-by:
-
Yongqiang Sun authored
[Why] DMCU isn't intiliazed properly by dmcub loading due to dmcub initialize sequence. [How] Change dmcu init sequece to meet dmcub initilize. Signed-off-by:
-
Nicholas Kazlauskas authored
The DMUB service is the interface to the DMCUB. It's required to support Renoir features so it will be enabled and compiled automatically when the Renoir display engine is enabled via CONFIG_DRM_AMD_DC_DCN2_1. DMUB code will initially be guarded by CONFIG_DRM_AMD_DC_DMUB and later switched to CONFIG_DRM_AMD_DC_DCN2_1 with the config option dropped. Signed-off-by:
-
Nicholas Kazlauskas authored
The interface to the DMCUB won't be through DC itself. DC will instead call into the DMUB interface introduced with a future change. The CONFIG_DRM_AMD_DC_DMUB defines will still be used for now but will be dropped at the end of the series. Since this define was never configurable in the first place this code wasn't used. Signed-off-by:
-
Nicholas Kazlauskas authored
DMCUB ucode requires secure loading through PSP. This is already supported in PSP as GFX_FW_TYPE_DMUB, it just needs to be mapped from AMDGPU_UCODE_ID_DMCUB to GFX_FW_TYPE_DMUB. DMUB is a shorthand name for DMCUB and can be used interchangeably. Signed-off-by:
-
Nicholas Kazlauskas authored
The DMCUB is a secondary DMCU (Display MicroController Unit) that has its own separate firmware. It's required for DMCU support on Renoir. Signed-off-by:
-
Colin Ian King authored
Currently pointer aconnector is being dereferenced by the call to to_dm_connector_state before it is being null checked, this could lead to a null pointer dereference. Fix this by checking that aconnector is null before dereferencing it. Addresses-Coverity: ("Dereference before null check") Reviewed-by:Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Mikita Lipski authored
- Adding encoder atomic check to find vcpi slots for a connector - Using DRM helper functions to calculate PBN - Adding connector atomic check to release vcpi slots if connector loses CRTC - Calculate PBN and VCPI slots only once during atomic check and store them on crtc_state to eliminate redundant calculation - Call drm_dp_mst_atomic_check to verify validity of MST topology during state atomic check v2: squashed previous 3 separate patches, removed DSC PBN calculation, and added PBN and VCPI slots properties to amdgpu connector v3: - moved vcpi_slots and pbn properties to dm_crtc_state and dc_stream_state - updates stream's vcpi_slots and pbn on commit - separated patch from the DSC MST series v4: - set vcpi_slots and pbn properties to dm_connector_state - copy porperties from connector state on to crtc state v5: - keep the pbn and vcpi values only on connnector state - added a void pointer to the stream state instead on two ints, because dc_stream_state is OS agnostic. Pointer points to the current dm_connector_state. v6: - Remove new param from stream v7: - Fix error with using max capable bpc v8: - squash in fix from Gustavo A. R. Silva Reviewed-by:
Lyude Paul <lyude@redhat.com> Reviewed-by:
-
Alex Deucher authored
flush/cancel delayed works before doing finalization to avoid concurrently requests. Reviewed-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
-
Kenneth Feng authored
sysfs interface to read pcie speed&width info on navi1x. v2: fix warning (trivial) Signed-off-by:
Kenneth Feng <kenneth.feng@amd.com> Reviewed-by:
Evan Quan <evan.quan@amd.com> Signed-off-by:
-
- 11 Nov, 2019 3 commits
-
-
Matt Coffin authored
[Why] On Navi10, and presumably arcterus, updating pp_table via sysfs would not re-scale the maximum possible power limit one can set. On navi10, the SMU code ignored the power percentage overdrive setting entirely, and would not allow you to exceed the default power limit at all. [How] Adding a function to the SMU interface to get the pptable version of the default power limit allows ASIC-specific code to provide the correct maximum-settable power limit for the current pptable. v3: fix spelling (Alex) Reviewed-by:
Matt Coffin <mcoffin13@gmail.com> Signed-off-by:
-
Matt Coffin authored
[Why] Before this patch, navi10 overdrive settings could not be printed via pp_od_clk_voltage [How] Implement printing for the overdrive settings for the following clocks in navi10's ppt print_clk_levels implementation: * SMU_OD_SCLK * SMU_OD_MCLK * SMU_OD_VDDC_CURVE Reviewed-by:
-
Matt Coffin authored
[Why] Before this patch, there was no way to set the gfxclk voltage curve in the overdrive settings for navi10 through pp_od_clk_voltage [How] Add the required implementation to navi10's ppt dpm table editing implementation, similar to the vega20 implementation and interface. Reviewed-by:
-
