Pull i2c updates from Wolfram Sang:
 "Features:

   - new drivers: Renesas EMEV2, register based MUX, NXP LPC2xxx
   - core: scans DT and assigns wakeup interrupts.  no driver changes needed.
   - core: some refcouting issues fixed and better API for that
   - core: new helper function for best effort block read emulation
   - slave framework: proper DT bindings and userspace instantiation
   - some bigger work for xiic, pxa, omap drivers

  .. and quite a number of smaller driver fixes, cleanups, improvements"

* 'i2c/for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (65 commits)
  i2c: mux: reg Change ioread endianness for readback
  i2c: mux: reg: fix compilation warnings
  i2c: mux: reg: simplify register size checking
  i2c: muxes: fix leaked i2c adapter device node references
  i2c: allow specifying separate wakeup interrupt in device tree
  of/irq: export of_get_irq_byname()
  i2c: xgene-slimpro: dma_mapping_error() doesn't return an error code
  i2c: Replace I2C_CROS_EC_TUNNEL dependency
  eeprom: at24: use i2c_smbus_read_i2c_block_data_or_emulated
  i2c: core: Add support for best effort block read emulation
  i2c: lpc2k: add driver
  i2c: mux: Add register-based mux i2c-mux-reg
  i2c: dt: describe generic bindings
  i2c: slave: print warning if slave flag not set
  i2c: support 10 bit and slave addresses in sysfs 'new_device'
  i2c: take address space into account when checking for used addresses
  i2c: apply DT flags when probing
  i2c: make address check indpendent from client struct
  i2c: rename address check functions
  i2c: apply address offset for slaves, too
  ...

Pull RTC updates from Alexandre Belloni:
 "Core:
   - use is_visible() to control sysfs attributes
   - switch wakealarm attribute to DEVICE_ATTR_RW
   - make rtc_does_wakealarm() return boolean
   - properly manage lifetime of dev and cdev in rtc device
   - remove unnecessary device_get() in rtc_device_unregister
   - fix double free in rtc_register_device() error path

  New drivers:
   - NXP LPC24xx
   - Xilinx Zynq MP
   - Dialog DA9062

  Subsystem wide cleanups:
   - fix drivers that consider 0 as a valid IRQ in client->irq
   - Drop (un)likely before IS_ERR(_OR_NULL)
   - drop the remaining owner assignment for i2c_driver and
     platform_driver
   - module autoload fixes

  Drivers:
   - 88pm80x: add device tree support
   - abx80x: fix RTC write bit
   - ab8500: Add a sentinel to ab85xx_rtc_ids[]
   - armada38x: Align RTC set time procedure with the official errata
   - as3722: correct month value
   - at91sam9: cleanups
   - at91rm9200: get and use slow clock and cleanups
   - bq32k: remove redundant check
   - cmos: century support, proper fix for the spurious wakeup
   - ds1307: cleanups and wakeup irq support
   - ds1374: Remove unused variable
   - ds1685: Use module_platform_driver
   - ds3232: fix WARNING trace in resume function
   - gemini: fix ptr_ret.cocci warnings
   - mt6397: implement suspend/resume
   - omap: support internal and external clock enabling
   - opal: Enable alarms only when opal supports tpo
   - pcf2127: use OFS flag to detect unreliable date and warn the user
   - pl031: fix typo for author email
   - rx8025: huge cleanup and fixes
   - sa1100/pxa: share common code
   - s5m: fix to update ctrl register
   - s3c: fix clocks and wakeup, cleanup
   - sirfsoc: use regmap
   - nvram_read()/nvram_write() functions for cmos, ds1305, ds1307,
     ds1343, ds1511, ds1553, ds1742, m48t59, rp5c01, stk17ta8, tx4939
   - use rtc_valid_tm() error code when reading date/time instead of 0
     for isl12022, pcf2123, pcf2127"

* tag 'rtc-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (90 commits)
  rtc: abx80x: fix RTC write bit
  rtc: ab8500: Add a sentinel to ab85xx_rtc_ids[]
  rtc: ds1374: Remove unused variable
  rtc: Fix module autoload for OF platform drivers
  rtc: Fix module autoload for rtc-{ab8500,max8997,s5m} drivers
  rtc: omap: Add external clock enabling support
  rtc: omap: Add internal clock enabling support
  ARM: dts: AM437x: Add the internal and external clock nodes for rtc
  rtc: s5m: fix to update ctrl register
  rtc: add xilinx zynqmp rtc driver
  devicetree: bindings: rtc: add bindings for xilinx zynqmp rtc
  rtc: as3722: correct month value
  ARM: config: Switch PXA27x platforms to use PXA RTC driver
  ARM: mmp: remove unused RTC register definitions
  ARM: sa1100: remove unused RTC register definitions
  rtc: sa1100/pxa: convert to run-time register mapping
  ARM: pxa: add memory resource to SA1100 RTC device
  rtc: pxa: convert to use shared sa1100 functions
  rtc: sa1100: prepare to share sa1100_rtc_ops
  rtc: ds3232: fix WARNING trace in resume function
  ...

Pull libnvdimm updates from Dan Williams:
 "This update has successfully completed a 0day-kbuild run and has
  appeared in a linux-next release.  The changes outside of the typical
  drivers/nvdimm/ and drivers/acpi/nfit.[ch] paths are related to the
  removal of IORESOURCE_CACHEABLE, the introduction of memremap(), and
  the introduction of ZONE_DEVICE + devm_memremap_pages().

  Summary:

   - Introduce ZONE_DEVICE and devm_memremap_pages() as a generic
     mechanism for adding device-driver-discovered memory regions to the
     kernel's direct map.

     This facility is used by the pmem driver to enable pfn_to_page()
     operations on the page frames returned by DAX ('direct_access' in
     'struct block_device_operations').

     For now, the 'memmap' allocation for these "device" pages comes
     from "System RAM".  Support for allocating the memmap from device
     memory will arrive in a later kernel.

   - Introduce memremap() to replace usages of ioremap_cache() and
     ioremap_wt().  memremap() drops the __iomem annotation for these
     mappings to memory that do not have i/o side effects.  The
     replacement of ioremap_cache() with memremap() is limited to the
     pmem driver to ease merging the api change in v4.3.

     Completion of the conversion is targeted for v4.4.

   - Similar to the usage of memcpy_to_pmem() + wmb_pmem() in the pmem
     driver, update the VFS DAX implementation and PMEM api to provide
     persistence guarantees for kernel operations on a DAX mapping.

   - Convert the ACPI NFIT 'BLK' driver to map the block apertures as
     cacheable to improve performance.

   - Miscellaneous updates and fixes to libnvdimm including support for
     issuing "address range scrub" commands, clarifying the optimal
     'sector size' of pmem devices, a clarification of the usage of the
     ACPI '_STA' (status) property for DIMM devices, and other minor
     fixes"

* tag 'libnvdimm-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (34 commits)
  libnvdimm, pmem: direct map legacy pmem by default
  libnvdimm, pmem: 'struct page' for pmem
  libnvdimm, pfn: 'struct page' provider infrastructure
  x86, pmem: clarify that ARCH_HAS_PMEM_API implies PMEM mapped WB
  add devm_memremap_pages
  mm: ZONE_DEVICE for "device memory"
  mm: move __phys_to_pfn and __pfn_to_phys to asm/generic/memory_model.h
  dax: drop size parameter to ->direct_access()
  nd_blk: change aperture mapping from WC to WB
  nvdimm: change to use generic kvfree()
  pmem, dax: have direct_access use __pmem annotation
  dax: update I/O path to do proper PMEM flushing
  pmem: add copy_from_iter_pmem() and clear_pmem()
  pmem, x86: clean up conditional pmem includes
  pmem: remove layer when calling arch_has_wmb_pmem()
  pmem, x86: move x86 PMEM API to new pmem.h header
  libnvdimm, e820: make CONFIG_X86_PMEM_LEGACY a tristate option
  pmem: switch to devm_ allocations
  devres: add devm_memremap
  libnvdimm, btt: write and validate parent_uuid
  ...

Pull misc kbuild updates from Michal Marek:
 - deb-pkg:
     + module signing fix
     + dtb files are added to the package
     + do not require `hostname -f` to work during build
     + make deb-pkg generates a source package, bindeb-pkg has been
       added to only generate the binary package
 - rpm-pkg packages /lib/modules as well
 - new coccinelle patch and updates to existing ones
 - new stackusage & stackdelta script to collect and compare stack usage
   info (using gcc's -fstack-usage)
 - make tags understands trace_*_rcuidle() macros
 - .gitignore updates, misc cleanups

* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild: (27 commits)
  deb-pkg: add source package
  package/Makefile: move source tar creation to a function
  scripts: add stackdelta script
  kbuild: remove *.su files generated by -fstack-usage
  .gitignore: add *.su pattern
  scripts: add stackusage script
  kbuild: avoid listing /lib/modules in kernel spec file
  fallback to hostname in scripts/package/builddeb
  coccinelle: api: extend spatch for dropping unnecessary owner
  deb-pkg: simplify directory creation
  scripts/tags.sh: Include trace_*_rcuidle() in tags
  scripts/package/Makefile: rpmbuild is needed for rpm targets
  Kbuild: Add ID files to .gitignore
  gitignore: Add MIPS vmlinux.32 to the list
  coccinelle: simple_return: Add a blank line
  coccinelle: irqf_oneshot.cocci: Improve the generated commit log
  coccinelle: api: add vma_pages.cocci
  scripts/coccinelle/misc/irqf_oneshot.cocci: Fix grammar
  scripts/coccinelle/misc/semicolon.cocci: Use imperative mood
  coccinelle: simple_open: Use imperative mood
  ...

Pull kconfig updates from Michal Marek:
 - kconfig warns about junk characters in Kconfig files
 - merge_config.sh error handling
 - small cleanup

* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  merge_config.sh: exit on missing input files
  kconfig: Regenerate shipped zconf.{hash,lex}.c files
  kconfig: warn of unhandled characters in Kconfig commands
  kconfig: Delete unnecessary checks before the function call "sym_calc_value"

Pull core kbuild updates from Michal Marek:
 - modpost portability fix
 - linker script fix
 - genksyms segfault fix
 - fixdep cleanup
 - fix for clang detection

* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  kbuild: Fix clang detection
  kbuild: fixdep: drop meaningless hash table initialization
  kbuild: fixdep: optimize code slightly
  genksyms: Regenerate parser
  genksyms: Duplicate function pointer type definitions segfault
  kbuild: Fix .text.unlikely placement
  Avoid conflict with host definitions when cross-compiling

Pull tracing update from Steven Rostedt:
 "Mostly this is just clean ups and micro optimizations.

  The changes with more meat are:

   - Allowing the trace event filters to filter on CPU number and
     process ids

   - Two new markers for trace output latency were added (10 and 100
     msec latencies)

   - Have tracing_thresh filter function profiling time

  I also worked on modifying the ring buffer code for some future work,
  and moved the adding of the timestamp around.  One of my changes
  caused a regression, and since other changes were built on top of it
  and already tested, I had to operate a revert of that change.  Instead
  of rebasing, this change set has the code that caused a regression as
  well as the code to revert that change without touching the other
  changes that were made on top of it"

* tag 'trace-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  ring-buffer: Revert "ring-buffer: Get timestamp after event is allocated"
  tracing: Don't make assumptions about length of string on task rename
  tracing: Allow triggers to filter for CPU ids and process names
  ftrace: Format MCOUNT_ADDR address as type unsigned long
  tracing: Introduce two additional marks for delay
  ftrace: Fix function_graph duration spacing with 7-digits
  ftrace: add tracing_thresh to function profile
  tracing: Clean up stack tracing and fix fentry updates
  ring-buffer: Reorganize function locations
  ring-buffer: Make sure event has enough room for extend and padding
  ring-buffer: Get timestamp after event is allocated
  ring-buffer: Move the adding of the extended timestamp out of line
  ring-buffer: Add event descriptor to simplify passing data
  ftrace: correct the counter increment for trace_buffer data
  tracing: Fix for non-continuous cpu ids
  tracing: Prefer kcalloc over kzalloc with multiply

Pull audit update from Paul Moore:
 "This is one of the larger audit patchsets in recent history,
  consisting of eight patches and almost 400 lines of changes.

  The bulk of the patchset is the new "audit by executable"
  functionality which allows admins to set an audit watch based on the
  executable on disk.  Prior to this, admins could only track an
  application by PID, which has some obvious limitations.

  Beyond the new functionality we also have some refcnt fixes and a few
  minor cleanups"

* 'upstream' of git://git.infradead.org/users/pcmoore/audit:
  fixup: audit: implement audit by executable
  audit: implement audit by executable
  audit: clean simple fsnotify implementation
  audit: use macros for unset inode and device values
  audit: make audit_del_rule() more robust
  audit: fix uninitialized variable in audit_add_rule()
  audit: eliminate unnecessary extra layer of watch parent references
  audit: eliminate unnecessary extra layer of watch references

Pull security subsystem updates from James Morris:
 "Highlights:

   - PKCS#7 support added to support signed kexec, also utilized for
     module signing.  See comments in 3f1e1bea.

     ** NOTE: this requires linking against the OpenSSL library, which
        must be installed, e.g.  the openssl-devel on Fedora **

   - Smack
      - add IPv6 host labeling; ignore labels on kernel threads
      - support smack labeling mounts which use binary mount data

   - SELinux:
      - add ioctl whitelisting (see
        http://kernsec.org/files/lss2015/vanderstoep.pdf)
      - fix mprotect PROT_EXEC regression caused by mm change

   - Seccomp:
      - add ptrace options for suspend/resume"

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (57 commits)
  PKCS#7: Add OIDs for sha224, sha284 and sha512 hash algos and use them
  Documentation/Changes: Now need OpenSSL devel packages for module signing
  scripts: add extract-cert and sign-file to .gitignore
  modsign: Handle signing key in source tree
  modsign: Use if_changed rule for extracting cert from module signing key
  Move certificate handling to its own directory
  sign-file: Fix warning about BIO_reset() return value
  PKCS#7: Add MODULE_LICENSE() to test module
  Smack - Fix build error with bringup unconfigured
  sign-file: Document dependency on OpenSSL devel libraries
  PKCS#7: Appropriately restrict authenticated attributes and content type
  KEYS: Add a name for PKEY_ID_PKCS7
  PKCS#7: Improve and export the X.509 ASN.1 time object decoder
  modsign: Use extract-cert to process CONFIG_SYSTEM_TRUSTED_KEYS
  extract-cert: Cope with multiple X.509 certificates in a single file
  sign-file: Generate CMS message as signature instead of PKCS#7
  PKCS#7: Support CMS messages also [RFC5652]
  X.509: Change recorded SKID & AKID to not include Subject or Issuer
  PKCS#7: Check content type and versions
  MAINTAINERS: The keyrings mailing list has moved
  ...

Pull NMI backtrace update from Russell King:
 "These changes convert the x86 NMI handling to be a library
  implementation which other architectures can make use of.  Thomas
  Gleixner has reviewed and tested these changes, and wishes me to send
  these rather than taking them through the tip tree.

  The final patch in the set adds an initial implementation using this
  infrastructure to ARM, even though it doesn't send the IPI at "NMI"
  level.  Patches are in progress to add the ARM equivalent of NMI, but
  we still need the IRQ-level fallback for systems where the "NMI" isn't
  available due to secure firmware denying access to it"

* 'nmi' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: add basic support for on-demand backtrace of other CPUs
  nmi: x86: convert to generic nmi handler
  nmi: create generic NMI backtrace implementation

Pull xen updates from David Vrabel:
 "Xen features and fixes for 4.3:

   - Convert xen-blkfront to the multiqueue API
   - [arm] Support binding event channels to different VCPUs.
   - [x86] Support > 512 GiB in a PV guests (off by default as such a
     guest cannot be migrated with the current toolstack).
   - [x86] PMU support for PV dom0 (limited support for using perf with
     Xen and other guests)"

* tag 'for-linus-4.3-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (33 commits)
  xen: switch extra memory accounting to use pfns
  xen: limit memory to architectural maximum
  xen: avoid another early crash of memory limited dom0
  xen: avoid early crash of memory limited dom0
  arm/xen: Remove helpers which are PV specific
  xen/x86: Don't try to set PCE bit in CR4
  xen/PMU: PMU emulation code
  xen/PMU: Intercept PMU-related MSR and APIC accesses
  xen/PMU: Describe vendor-specific PMU registers
  xen/PMU: Initialization code for Xen PMU
  xen/PMU: Sysfs interface for setting Xen PMU mode
  xen: xensyms support
  xen: remove no longer needed p2m.h
  xen: allow more than 512 GB of RAM for 64 bit pv-domains
  xen: move p2m list if conflicting with e820 map
  xen: add explicit memblock_reserve() calls for special pages
  mm: provide early_memremap_ro to establish read-only mapping
  xen: check for initrd conflicting with e820 map
  xen: check pre-allocated page tables for conflict with memory map
  xen: check for kernel memory conflicting with memory layout
  ...

Pull more irq updates from Thomas Gleixner:
 "The second part of irq related updates:

   - Provide EOImode for GIC[V3] irq chips, which is a prerequisite for
     direct interrupt handling in [KVM] guests"

* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/GIC: Fix EOImode setting for non-DT/ACPI systems
  irqchip/GIC: Don't deactivate interrupts forwarded to a guest
  irqchip/GIC: Convert to EOImode == 1
  irqchip/GICv3: Don't deactivate interrupts forwarded to a guest
  irqchip/GICv3: Convert to EOImode == 1

Pull m68k/colfire fixes from Greg Ungerer:
 "Only a couple of patches this time.  One migrating the clock driver
  code to the new set-state interface.  The other cleaning up to use the
  PFN_DOWN macro"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
  m68k/coldfire: use PFN_DOWN macro
  m68k/coldfire/pit: Migrate to new 'set-state' interface

Merge tag 'ecryptfs-4.3-rc1-stale-dcache' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs

Pull ecryptfs fixes from Tyler Hicks:
 "Invalidate stale eCryptfs dcache entries caused by unlinked lower
  inodes"

* tag 'ecryptfs-4.3-rc1-stale-dcache' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  eCryptfs: Delete a check before the function call "key_put"
  eCryptfs: Invalidate dcache entries when lower i_nlink is zero

Pull crypto fix from Herbert Xu:
 "This fixes a memory corruption bug in ghash-clmulni-intel due to
  insufficient memory allocation"

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: ghash-clmulni: specify context size for ghash async algorithm

It changed as result of other syscalls, and while the system call list
itself was correctly updated, the selftest program was not.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Instead of using physical addresses for accounting of extra memory
areas available for ballooning switch to pfns as this is much less
error prone regarding partial pages.
Reported-by: Roger Pau Monné <roger.pau@citrix.com>
Tested-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

When a pv-domain (including dom0) is started it tries to size it's
p2m list according to the maximum possible memory amount it ever can
achieve. Limit the initial maximum memory size to the architectural
limit of the hardware in order to avoid overflows during remapping
of memory.

This problem will occur when dom0 is started with an initial memory
size being a multiple of 1GB, but without specifying it's maximum
memory size. The kernel must be configured without
CONFIG_XEN_BALLOON_MEMORY_HOTPLUG for the problem to happen.
Reported-by: Roger Pau Monné <roger.pau@citrix.com>
Tested-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

Commit b1c9f169047b ("xen: split counting of extra memory pages...")
introduced an error when dom0 was started with limited memory occurring
only on some hardware.

The problem arises in case dom0 is started with initial memory and
maximum memory being the same. The kernel must be configured without
CONFIG_XEN_BALLOON_MEMORY_HOTPLUG for the problem to happen. If all
of this is true and the E820 map of the machine is sparse (some areas
are not covered) then the machine might crash early in the boot
process.

An example E820 map triggering the problem looks like this:

[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009d7ff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009d800-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000cf7fafff] usable
[    0.000000] BIOS-e820: [mem 0x00000000cf7fb000-0x00000000cf95ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000cf960000-0x00000000cfb62fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000cfb63000-0x00000000cfd14fff] usable
[    0.000000] BIOS-e820: [mem 0x00000000cfd15000-0x00000000cfd61fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000cfd62000-0x00000000cfd6cfff] ACPI data
[    0.000000] BIOS-e820: [mem 0x00000000cfd6d000-0x00000000cfd6ffff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000cfd70000-0x00000000cfd70fff] usable
[    0.000000] BIOS-e820: [mem 0x00000000cfd71000-0x00000000cfea8fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000cfea9000-0x00000000cfeb9fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000cfeba000-0x00000000cfecafff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000cfecb000-0x00000000cfecbfff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000cfecc000-0x00000000cfedbfff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000cfedc000-0x00000000cfedcfff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000cfedd000-0x00000000cfeddfff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000cfede000-0x00000000cfee3fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000cfee4000-0x00000000cfef6fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000cfef7000-0x00000000cfefffff] usable
[    0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec10000-0x00000000fec10fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed40000-0x00000000fed44fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed61000-0x00000000fed70fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed80000-0x00000000fed8ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100001000-0x000000020effffff] usable

In this case the area a0000-dffff isn't present in the map. This will
confuse the memory setup of the domain when remapping the memory from
such holes to populated areas.

To avoid the problem the accounting of to be remapped memory has to
count such holes in the E820 map as well.
Reported-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

Commit b1c9f169047b ("xen: split counting of extra memory pages...")
introduced an error when dom0 was started with limited memory.

The problem arises in case dom0 is started with initial memory and
maximum memory being the same and exactly a multiple of 1 GB. The
kernel must be configured without CONFIG_XEN_BALLOON_MEMORY_HOTPLUG
for the problem to happen. In this case it will crash very early
during boot due to the virtual mapped p2m list not being large
enough to be able to remap any memory:

(XEN) Freed 304kB init memory.
mapping kernel into physical memory
about to get started...
(XEN) traps.c:459:d0v0 Unhandled invalid opcode fault/trap [#6] on VCPU 0 [ec=0000]
(XEN) domain_crash_sync called from entry.S: fault at ffff82d080229a93 create_bounce_frame+0x12b/0x13a
(XEN) Domain 0 (vcpu#0) crashed on cpu#0:
(XEN) ----[ Xen-4.5.2-pre  x86_64  debug=n Not tainted ]----
(XEN) CPU:    0
(XEN) RIP:    e033:[<ffffffff81d120cb>]
(XEN) RFLAGS: 0000000000000206   EM: 1 CONTEXT: pv guest (d0v0)
(XEN) rax: ffffffff81db2000   rbx: 000000004d000000   rcx: 0000000000000000
(XEN) rdx: 000000004d000000   rsi: 0000000000063000   rdi: 000000004d063000
(XEN) rbp: ffffffff81c03d78   rsp: ffffffff81c03d28   r8:  0000000000023000
(XEN) r9:  00000001040ff000   r10: 0000000000007ff0   r11: 0000000000000000
(XEN) r12: 0000000000063000   r13: 000000000004d000   r14: 0000000000000063
(XEN) r15: 0000000000000063   cr0: 0000000080050033   cr4: 00000000000006f0
(XEN) cr3: 0000000105c0f000   cr2: ffffc90000268000
(XEN) ds: 0000   es: 0000   fs: 0000   gs: 0000   ss: e02b   cs: e033
(XEN) Guest stack trace from rsp=ffffffff81c03d28:
(XEN)   0000000000000000 0000000000000000 ffffffff81d120cb 000000010000e030
(XEN)   0000000000010006 ffffffff81c03d68 000000000000e02b ffffffffffffffff
(XEN)   0000000000000063 000000000004d063 ffffffff81c03de8 ffffffff81d130a7
(XEN)   ffffffff81c03de8 000000000004d000 00000001040ff000 0000000000105db1
(XEN)   00000001040ff001 000000000004d062 ffff8800092d6ff8 0000000002027000
(XEN)   ffff8800094d8340 ffff8800092d6ff8 00003ffffffff000 ffff8800092d7ff8
(XEN)   ffffffff81c03e48 ffffffff81d13c43 ffff8800094d8000 ffff8800094d9000
(XEN)   0000000000000000 ffff8800092d6000 00000000092d6000 000000004cfbf000
(XEN)   00000000092d6000 00000000052d5442 0000000000000000 0000000000000000
(XEN)   ffffffff81c03ed8 ffffffff81d185c1 0000000000000000 0000000000000000
(XEN)   ffffffff81c03e78 ffffffff810f8ca4 ffffffff81c03ed8 ffffffff8171a15d
(XEN)   0000000000000010 ffffffff81c03ee8 0000000000000000 0000000000000000
(XEN)   ffffffff81f0e402 ffffffffffffffff ffffffff81dae900 0000000000000000
(XEN)   0000000000000000 0000000000000000 ffffffff81c03f28 ffffffff81d0cf0f
(XEN)   0000000000000000 0000000000000000 0000000000000000 ffffffff81db82e0
(XEN)   0000000000000000 0000000000000000 0000000000000000 0000000000000000
(XEN)   ffffffff81c03f38 ffffffff81d0c603 ffffffff81c03ff8 ffffffff81d11c86
(XEN)   0300000100000032 0000000000000005 0000000000000020 0000000000000000
(XEN)   0000000000000000 0000000000000000 0000000000000000 0000000000000000
(XEN)   0000000000000000 0000000000000000 0000000000000000 0000000000000000
(XEN) Domain 0 crashed: rebooting machine in 5 seconds.

This can be avoided by allocating aneough space for the p2m to cover
the maximum memory of dom0 plus the identity mapped holes required
for PCI space, BIOS etc.
Reported-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

Pull NFS client updates from Trond Myklebust:
 "Highlights include:

  Stable patches:
   - Fix atomicity of pNFS commit list updates
   - Fix NFSv4 handling of open(O_CREAT|O_EXCL|O_RDONLY)
   - nfs_set_pgio_error sometimes misses errors
   - Fix a thinko in xs_connect()
   - Fix borkage in _same_data_server_addrs_locked()
   - Fix a NULL pointer dereference of migration recovery ops for v4.2
     client
   - Don't let the ctime override attribute barriers.
   - Revert "NFSv4: Remove incorrect check in can_open_delegated()"
   - Ensure flexfiles pNFS driver updates the inode after write finishes
   - flexfiles must not pollute the attribute cache with attrbutes from
     the DS
   - Fix a protocol error in layoutreturn
   - Fix a protocol issue with NFSv4.1 CLOSE stateids

  Bugfixes + cleanups
   - pNFS blocks bugfixes from Christoph
   - Various cleanups from Anna
   - More fixes for delegation corner cases
   - Don't fsync twice for O_SYNC/IS_SYNC files
   - Fix pNFS and flexfiles layoutstats bugs
   - pnfs/flexfiles: avoid duplicate tracking of mirror data
   - pnfs: Fix layoutget/layoutreturn/return-on-close serialisation
     issues
   - pnfs/flexfiles: error handling retries a layoutget before fallback
     to MDS

  Features:
   - Full support for the OPEN NFS4_CREATE_EXCLUSIVE4_1 mode from
     Kinglong
   - More RDMA client transport improvements from Chuck
   - Removal of the deprecated ib_reg_phys_mr() and ib_rereg_phys_mr()
     verbs from the SUNRPC, Lustre and core infiniband tree.
   - Optimise away the close-to-open getattr if there is no cached data"

* tag 'nfs-for-4.3-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (108 commits)
  NFSv4: Respect the server imposed limit on how many changes we may cache
  NFSv4: Express delegation limit in units of pages
  Revert "NFS: Make close(2) asynchronous when closing NFS O_DIRECT files"
  NFS: Optimise away the close-to-open getattr if there is no cached data
  NFSv4.1/flexfiles: Clean up ff_layout_write_done_cb/ff_layout_commit_done_cb
  NFSv4.1/flexfiles: Mark the layout for return in ff_layout_io_track_ds_error()
  nfs: Remove unneeded checking of the return value from scnprintf
  nfs: Fix truncated client owner id without proto type
  NFSv4.1/flexfiles: Mark layout for return if the mirrors are invalid
  NFSv4.1/flexfiles: RW layouts are valid only if all mirrors are valid
  NFSv4.1/flexfiles: Fix incorrect usage of pnfs_generic_mark_devid_invalid()
  NFSv4.1/flexfiles: Fix freeing of mirrors
  NFSv4.1/pNFS: Don't request a minimal read layout beyond the end of file
  NFSv4.1/pnfs: Handle LAYOUTGET return values correctly
  NFSv4.1/pnfs: Don't ask for a read layout for an empty file.
  NFSv4.1: Fix a protocol issue with CLOSE stateids
  NFSv4.1/flexfiles: Don't mark the entire deviceid as bad for file errors
  SUNRPC: Prevent SYN+SYNACK+RST storms
  SUNRPC: xs_reset_transport must mark the connection as disconnected
  NFSv4.1/pnfs: Ensure layoutreturn reserves space for the opaque payload
  ...

Pull xfs updates from Dave Chinner:
 "There isn't a whole lot to this update - it's mostly bug fixes and
  they are spread pretty much all over XFS.  There are some corruption
  fixes, some fixes for log recovery, some fixes that prevent unount
  from hanging, a lockdep annotation rework for inode locking to prevent
  false positives and the usual random bunch of cleanups and minor
  improvements.

  Deatils:

   - large rework of EFI/EFD lifecycle handling to fix log recovery
     corruption issues, crashes and unmount hangs

   - separate metadata UUID on disk to enable changing boot label UUID
     for v5 filesystems

   - fixes for gcc miscompilation on certain platforms and optimisation
     levels

   - remote attribute allocation and recovery corruption fixes

   - inode lockdep annotation rework to fix bugs with too many
     subclasses

   - directory inode locking changes to prevent lockdep false positives

   - a handful of minor corruption fixes

   - various other small cleanups and bug fixes"

* tag 'xfs-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs: (42 commits)
  xfs: fix error gotos in xfs_setattr_nonsize
  xfs: add mssing inode cache attempts counter increment
  xfs: return errors from partial I/O failures to files
  libxfs: bad magic number should set da block buffer error
  xfs: fix non-debug build warnings
  xfs: collapse allocsize and biosize mount option handling
  xfs: Fix file type directory corruption for btree directories
  xfs: lockdep annotations throw warnings on non-debug builds
  xfs: Fix uninitialized return value in xfs_alloc_fix_freelist()
  xfs: inode lockdep annotations broke non-lockdep build
  xfs: flush entire file on dio read/write to cached file
  xfs: Fix xfs_attr_leafblock definition
  libxfs: readahead of dir3 data blocks should use the read verifier
  xfs: stop holding ILOCK over filldir callbacks
  xfs: clean up inode lockdep annotations
  xfs: swap leaf buffer into path struct atomically during path shift
  xfs: relocate sparse inode mount warning
  xfs: dquots should be stamped with sb_meta_uuid
  xfs: log recovery needs to validate against sb_meta_uuid
  xfs: growfs not aware of sb_meta_uuid
  ...

The NFSv4 delegation spec allows the server to tell a client to limit how
much data it cache after the file is closed. In return, the server
guarantees enough free space to avoid ENOSPC situations, etc.
Prior to this patch, we assumed we could always cache aggressively after
close. Unfortunately, this causes problems with servers that set the
limit to 0 and therefore do not offer any ENOSPC guarantees.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>

Since we're tracking modifications to the page cache on a per-page
basis, it makes sense to express the limit to how much we may cache
in units of pages.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>

Pull vfs updates from Al Viro:
 "In this one:

   - d_move fixes (Eric Biederman)

   - UFS fixes (me; locking is mostly sane now, a bunch of bugs in error
     handling ought to be fixed)

   - switch of sb_writers to percpu rwsem (Oleg Nesterov)

   - superblock scalability (Josef Bacik and Dave Chinner)

   - swapon(2) race fix (Hugh Dickins)"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (65 commits)
  vfs: Test for and handle paths that are unreachable from their mnt_root
  dcache: Reduce the scope of i_lock in d_splice_alias
  dcache: Handle escaped paths in prepend_path
  mm: fix potential data race in SyS_swapon
  inode: don't softlockup when evicting inodes
  inode: rename i_wb_list to i_io_list
  sync: serialise per-superblock sync operations
  inode: convert inode_sb_list_lock to per-sb
  inode: add hlist_fake to avoid the inode hash lock in evict
  writeback: plug writeback at a high level
  change sb_writers to use percpu_rw_semaphore
  shift percpu_counter_destroy() into destroy_super_work()
  percpu-rwsem: kill CONFIG_PERCPU_RWSEM
  percpu-rwsem: introduce percpu_rwsem_release() and percpu_rwsem_acquire()
  percpu-rwsem: introduce percpu_down_read_trylock()
  document rwsem_release() in sb_wait_write()
  fix the broken lockdep logic in __sb_start_write()
  introduce __sb_writers_{acquired,release}() helpers
  ufs_inode_get{frag,block}(): get rid of 'phys' argument
  ufs_getfrag_block(): tidy up a bit
  ...

Merge tag 'for-linus-4.3-merge-window-part-1' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs

Pull 9p updates from Eric Van Hensbergen:
 "Just a few cleanups for 4.3 merge window for the 9p file system.  I've
  gotten several more over the past week, but this group has been in
  for-next for at least a couple of weeks so I figured I'd push them
  first while I test the rest.

  Most of the ones not in this set are bug-fixes anyways so I could hold
  them for rc1"

* tag 'for-linus-4.3-merge-window-part-1' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
  9p: fix return code of read() when count is 0
  9p: remove unused option Opt_trans

Pull media updates from Mauro Carvalho Chehab:
 - new DVB frontend drivers: ascot2e, cxd2841er, horus3a, lnbh25
 - new HDMI capture driver: tc358743
 - new driver for NetUP DVB new boards (netup_unidvb)
 - IR support for DVBSky cards (smipcie-ir)
 - Coda driver has gain macroblock tiling support
 - Renesas R-Car gains JPEG codec driver
 - new DVB platform driver for STi boards: c8sectpfe
 - added documentation for the media core kABI to device-drivers DocBook
 - lots of driver fixups, cleanups and improvements

* tag 'media/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (297 commits)
  [media] c8sectpfe: Remove select on undefined LIBELF_32
  [media] i2c: fix platform_no_drv_owner.cocci warnings
  [media] cx231xx: Use wake_up_interruptible() instead of wake_up_interruptible_nr()
  [media] tc358743: only queue subdev notifications if devnode is set
  [media] tc358743: add missing Kconfig dependency/select
  [media] c8sectpfe: Use %pad to print 'dma_addr_t'
  [media] DocBook media: Fix typo "the the" in xml files
  [media] tc358743: make reset gpio optional
  [media] tc358743: set direction of reset gpio using devm_gpiod_get
  [media] dvbdev: document most of the functions/data structs
  [media] dvb_frontend.h: document the struct dvb_frontend
  [media] dvb-frontend.h: document struct dtv_frontend_properties
  [media] dvb-frontend.h: document struct dvb_frontend_ops
  [media] dvb: Use DVBFE_ALGO_HW where applicable
  [media] dvb_frontend.h: document struct analog_demod_ops
  [media] dvb_frontend.h: Document struct dvb_tuner_ops
  [media] Docbook: Document struct analog_parameters
  [media] dvb_frontend.h: get rid of dvbfe_modcod
  [media] add documentation for struct dvb_tuner_info
  [media] dvb_frontend: document dvb_frontend_tune_settings
  ...

Pull mailbox updates from Jassi Brar:
 "Mainly we move from jiffy based timer to HRTIMER for finer control
  over polling.  Then a controller reduces its polling period from 10 to
  1ms"

* 'mailbox-for-next' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
  mailbox: arm_mhu: reduce txpoll_period from 10ms to 1 ms
  mailbox: switch to hrtimer for tx_complete polling
  mailbox: Drop owner assignment from platform_driver

Pull md updates from Neil Brown:

 - an assortment of little fixes, several for minor races only likely to
   be hit during testing

 - further cluster-md-raid1 development, not ready for real use yet.

 - new RAID6 syndrome code for ARM NEON

 - fix a race where a write can return before failure of one device is
   properly recorded in metadata, so an immediate crash might result in
   that write being lost.

* tag 'md/4.3' of git://neil.brown.name/md: (33 commits)
  md/raid5: ensure device failure recorded before write request returns.
  md/raid5: use bio_list for the list of bios to return.
  md/raid10: ensure device failure recorded before write request returns.
  md/raid1: ensure device failure recorded before write request returns.
  md-cluster: remove inappropriate try_module_get from join()
  md: extend spinlock protection in register_md_cluster_operations
  md-cluster: Read the disk bitmap sb and check if it needs recovery
  md-cluster: only call complete(&cinfo->completion) when node join cluster
  md-cluster: add missed lockres_free
  md-cluster: remove the unused sb_lock
  md-cluster: init suspend_list and suspend_lock early in join
  md-cluster: add the error check if failed to get dlm lock
  md-cluster: init completion within lockres_init
  md-cluster: fix deadlock issue on message lock
  md-cluster: transfer the resync ownership to another node
  md-cluster: split recover_slot for future code reuse
  md-cluster: use %pU to print UUIDs
  md: setup safemode_timer before it's being used
  md/raid5: handle possible race as reshape completes.
  md: sync sync_completed has correct value as recovery finishes.
  ...

Pull nfsd updates from Bruce Fields:
 "Nothing major, but:

   - Add Jeff Layton as an nfsd co-maintainer: no change to existing
     practice, just an acknowledgement of the status quo.

   - Two patches ("nfsd: ensure that...") for a race overlooked by the
     state locking rewrite, causing a crash noticed by multiple users.

   - Lots of smaller bugfixes all over from Kinglong Mee.

   - From Jeff, some cleanup of server rpc code in preparation for
     possible shift of nfsd threads to workqueues"

* tag 'nfsd-4.3' of git://linux-nfs.org/~bfields/linux: (52 commits)
  nfsd: deal with DELEGRETURN racing with CB_RECALL
  nfsd: return CLID_INUSE for unexpected SETCLIENTID_CONFIRM case
  nfsd: ensure that delegation stateid hash references are only put once
  nfsd: ensure that the ol stateid hash reference is only put once
  net: sunrpc: fix tracepoint Warning: unknown op '->'
  nfsd: allow more than one laundry job to run at a time
  nfsd: don't WARN/backtrace for invalid container deployment.
  fs: fix fs/locks.c kernel-doc warning
  nfsd: Add Jeff Layton as co-maintainer
  NFSD: Return word2 bitmask if setting security label in OPEN/CREATE
  NFSD: Set the attributes used to store the verifier for EXCLUSIVE4_1
  nfsd: SUPPATTR_EXCLCREAT must be encoded before SECURITY_LABEL.
  nfsd: Fix an FS_LAYOUT_TYPES/LAYOUT_TYPES encode bug
  NFSD: Store parent's stat in a separate value
  nfsd: Fix two typos in comments
  lockd: NLM grace period shouldn't block NFSv4 opens
  nfsd: include linux/nfs4.h in export.h
  sunrpc: Switch to using hash list instead single list
  sunrpc/nfsd: Remove redundant code by exports seq_operations functions
  sunrpc: Store cache_detail in seq_file's private directly
  ...

Pull btrfs updates from Chris Mason:
 "This has Jeff Mahoney's long standing trim patch that fixes corners
  where trims were missing.  Omar has some raid5/6 fixes, especially for
  using scrub and device replace when devices are missing.

  Zhao Lie continues cleaning and fixing things, this series fixes some
  really hard to hit corners in xfstests.  I had to pull it last merge
  window due to some deadlocks, but those are now resolved.

  I added support for Tejun's new blkio controllers.  It seems to work
  well for single devices, we'll expand to multi-device as well"

* 'for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (47 commits)
  btrfs: fix compile when block cgroups are not enabled
  Btrfs: fix file read corruption after extent cloning and fsync
  Btrfs: check if previous transaction aborted to avoid fs corruption
  btrfs: use __GFP_NOFAIL in alloc_btrfs_bio
  btrfs: Prevent from early transaction abort
  btrfs: Remove unused arguments in tree-log.c
  btrfs: Remove useless condition in start_log_trans()
  Btrfs: add support for blkio controllers
  Btrfs: remove unused mutex from struct 'btrfs_fs_info'
  Btrfs: fix parity scrub of RAID 5/6 with missing device
  Btrfs: fix device replace of a missing RAID 5/6 device
  Btrfs: add RAID 5/6 BTRFS_RBIO_REBUILD_MISSING operation
  Btrfs: count devices correctly in readahead during RAID 5/6 replace
  Btrfs: remove misleading handling of missing device scrub
  btrfs: fix clone / extent-same deadlocks
  Btrfs: fix defrag to merge tail file extent
  Btrfs: fix warning in backref walking
  btrfs: Add WARN_ON() for double lock in btrfs_tree_lock()
  btrfs: Remove root argument in extent_data_ref_count()
  btrfs: Fix wrong comment of btrfs_alloc_tree_block()
  ...

Merge patch-bomb from Andrew Morton:

 - a few misc things

 - Andy's "ambient capabilities"

 - fs/nofity updates

 - the ocfs2 queue

 - kernel/watchdog.c updates and feature work.

 - some of MM.  Includes Andrea's userfaultfd feature.

[ Hadn't noticed that userfaultfd was 'default y' when applying the
  patches, so that got fixed in this merge instead.  We do _not_ mark
  new features that nobody uses yet 'default y'   - Linus ]

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (118 commits)
  mm/hugetlb.c: make vma_has_reserves() return bool
  mm/madvise.c: make madvise_behaviour_valid() return bool
  mm/memory.c: make tlb_next_batch() return bool
  mm/dmapool.c: change is_page_busy() return from int to bool
  mm: remove struct node_active_region
  mremap: simplify the "overlap" check in mremap_to()
  mremap: don't do uneccesary checks if new_len == old_len
  mremap: don't do mm_populate(new_addr) on failure
  mm: move ->mremap() from file_operations to vm_operations_struct
  mremap: don't leak new_vma if f_op->mremap() fails
  mm/hugetlb.c: make vma_shareable() return bool
  mm: make GUP handle pfn mapping unless FOLL_GET is requested
  mm: fix status code which move_pages() returns for zero page
  mm: memcontrol: bring back the VM_BUG_ON() in mem_cgroup_swapout()
  genalloc: add support of multiple gen_pools per device
  genalloc: add name arg to gen_pool_get() and devm_gen_pool_create()
  mm/memblock: WARN_ON when nid differs from overlap region
  Documentation/features/vm: add feature description and arch support status for batched TLB flush after unmap
  mm: defer flush of writable TLB entries
  mm: send one IPI per CPU to TLB flush all entries after unmapping pages
  ...

In commit f341861f ("task_work: add a scheduling point in
task_work_run()") I fixed a latency problem adding a cond_resched()
call.

Later, commit ac3d0da8 added yet another loop to reverse a list,
bringing back the latency spike :

I've seen in some cases this loop taking 275 ms, if for example a
process with 2,000,000 files is killed.

We could add yet another cond_resched() in the reverse loop, or we
can simply remove the reversal, as I do not think anything
would depend on order of task_work_add() submitted works.

Fixes: ac3d0da8 ("task_work: Make task_work_add() lockless")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Maciej Żenczykowski <maze@google.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix RTC write bit as per application manual

Cc: stable@vger.kernel.org # 4.1+
Signed-off-by: Mitja Spes <mitja@lxnav.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Add a sentinel to ab85xx_rtc_ids[] in order to fix the following error:

drivers/rtc/rtc-ab8500: struct platform_device_id is 24 bytes.  The last of 2 is:
0x61 0x62 0x38 0x35 0x34 0x30 0x2d 0x72 0x74 0x63 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x8c
FATAL: drivers/rtc/rtc-ab8500: struct platform_device_id is not terminated with a NULL entry!
Reported-by: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Reported-by: Olof's autobuilder <build@lixom.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Remove unused variable 'res' and fix the following build warning:

drivers/rtc/rtc-ds1374.c:667:6: warning: unused variable 'res' [-Wunused-variable]
Reported-by: Olof's autobuilder <build@lixom.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

These platform drivers have a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

These platform drivers have a platform device ID table but the module
alias information is not created so module autoloading will not work.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Configure the clock source to external clock if available.
External clock is preferred as it can be ticking during suspend.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

The rtc can be clocked by an internal 32K clock. Adding the support
to enable the same.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>