- 10 Apr, 2015 40 commits
-
-
James Smart authored
Signed-off-by:
Dick Kennedy <dick.kennedy@emulex.com> Signed-off-by:
James Smart <james.smart@emulex.com> Reviewed-by:
Hannes Reinecke <hare@suse.de> Signed-off-by:
James Bottomley <JBottomley@Odin.com>
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Currently, the driver plays off the fact that older sli4 adapters have a different rpi access pattern that allowed for the rpi reference to be released earlier in the teardown sequence, allowing the driver to recycle the rpi value sooner. Newer sli4 adapters have a different access pattern that requires us to wait for a later mailbox completion. This changes the put call location on the newer sli4 adapters. Symptoms of the error are "0110 ELS" and the "0372 iotag" errors. Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Fix host reset escalation killing all IOs. SLI-3 adapters will use a new host template. The template differs from SLI-4 adapters in that it does not have an eh_host_reset_handler. Lpfc has traditionally never had a host_reset. The host reset handler was added when we ran into a stuck hardware condition on a SLI-4 adapter. The host_reset will reset and reinit the pci function, clearing the hardware condition. Unfortunately, the host reset handler uses attach/detach code paths, which makes scsi_add_host() and scsi_remove_host() calls. Meaning, a host_reset will completely remove the scsi_host from the system. As a new call to scsi_add_host() is made, the shost# changes, which results in completely new scsi_devices and device names. All the older scsi devices on the old shost# are now orphaned and unrecoverable. We realize we need to re-implement the host_reset_handler so the scsi_host stays registered across the host_reset, but that will be a rather lengthy effort. In the short term, we had an immediate need to restore the SLI-3 devices to their working behavior, with the easiest path being to remove their host_reset handler. Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
This will detect and send an async event if overtemp is detected Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
Ewan D. Milne <emilne@redhat.com> Signed-off-by:
-
Ondrej Zary authored
The loop in aha1542_outb with double-check is no longer needed, remove it. Signed-off-by:
Ondrej Zary <linux@rainbow-software.org> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Ondrej Zary authored
Bus reset always fails because aha1542_reset waits for the controller to assert the INIT bit (Mailbox Initialization Required) which it never does. This bit is asserted only after host reset. Remove the requirement for INIT bit (we really need only the IDLE bit). Signed-off-by:
-
Ondrej Zary authored
Remove aha1542_lock and use host_lock instead. Remove interrupt and queuecommand function wrappers. Remove locking from lowlevel _out and _in functions, they now can onle be called (at runtime) with host_lock being held. Remove ssleep(4) in aha1542_reset as we can't sleep while holding a spinlock. It's useless anyway as wait_mask will wait until the controller is idle and kernel waits for 10 seconds (HOST_RESET_SETTLE_TIME) after that. Signed-off-by:
-
Ondrej Zary authored
Enabling DEBUG disables write commands and devices with ID > 1. Remove this "feature" to allow real debugging. Signed-off-by:
-
Ondrej Zary authored
Signed-off-by:
-
Ondrej Zary authored
Remove DEB macro and join ifdef DEBUG blocks Signed-off-by:
-
Ondrej Zary authored
Signed-off-by:
-
Ondrej Zary authored
Pass struct Scsi_Host *sh and dma parameters instead of index to aha1542_set_bus_times. This is required for printk conversion. Signed-off-by:
-
Ondrej Zary authored
Pass struct Scsi_Host * to functions instead of base address. This reduces the number of parameters and is also required for printk conversion. Signed-off-by:
-
Ondrej Zary authored
Signed-off-by:
-
Ondrej Zary authored
Signed-off-by:
-
Ondrej Zary authored
Fix include guard in header file and remove useless changelog Signed-off-by:
-
Ondrej Zary authored
Make Scsi_Host variable names consistent - use sh everywhere. Signed-off-by:
-
Ondrej Zary authored
Use struct scsi_cmnd instead of Scsi_Cmnd and also rename the variables to get rid of SC prefix Signed-off-by:
-
Ondrej Zary authored
Make sure that there's no variable named cmd Signed-off-by:
-
Ondrej Zary authored
Simplify aha1542_biosparam, use sector_div, remove unused BIOS_TRANSLATION_1632. Signed-off-by:
-
Ondrej Zary authored
Remove __setup and introduce separate io, bus_on, bus_off and dma_speed module parameters. Signed-off-by:
-
Ondrej Zary authored
Cleanup hw_init, use goto for error handling. Signed-off-by:
-
Ondrej Zary authored
aha1542_out call is always followed by wait_mask. Move the call into aha1542_out to simplify code. Signed-off-by:
-
Ondrej Zary authored
Split out bus times related block of aha1542_hw_init into separate function aha1542_set_bus_times. Signed-off-by:
-
Ondrej Zary authored
aha1542_host_reset and aha1542_bus_reset are almost same, merge them into aha1542_reset Signed-off-by:
-
Ondrej Zary authored
aha1542_restart does nothing (except useless printk), remove it Signed-off-by:
-
