This patch adds dummy handlers for all known IEEE 802.15.4 dispatch
values which prints a warning that we don't support these dispatches
right now. Also we add a warning to the RX_CONTINUE case inside of
lowpan_rx_handlers_result which should now never happend.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch introduce an earlier check if a 6LoWPAN frame can be valid.
This contains at first for checking if the header contains a dispatch
byte and isn't the nalp dispatch value, which means it isn't a 6LoWPAN
packet. Also we add a check if we can derference the dispatch value by
checking if skb->len is unequal zero.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch complete reworks the evaluation of 6lowpan dispatch value by
introducing a receive handler mechanism for each dispatch value.

A list of changes:

 - Doing uncompression on-the-fly when FRAG1 is received, this require
   some special handling for 802.15.4 lltype in generic 6lowpan branch
   for setting the payload length correct.
 - Fix dispatch mask for fragmentation.
 - Add IPv6 dispatch evaluation for FRAG1.
 - Add skb_unshare for dispatch which might manipulate the skb data
   buffer.

Cc: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

We should change the skb->dev pointer earlier to the lowpan interface
Sometimes we call iphc_decompress which also use some netdev printout
functionality. This patch will change that the correct interface will be
displayed in this case, which should be the lowpan interface.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch moves some trivial checks at first before calling
skb_share_check which could do some memcpy if the buffer is shared.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch cleanups the pull of the iphc bytes. We don't need to check
if the skb->len contains two bytes, this will be checked by
lowpan_fetch_skb_u8.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

We don't need to check if the wpan interface is running because the
lowpan_rcv is the packet layer receive handler for the wpan interface.

Instead doing a check if wpan interface is running we should check if
the lowpan interface is running before starting 6lowpan adaptation layer.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This function is used internally inside of ieee802154 6lowpan module
only and not outside of any other module. We don't need to export this
function then.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Internal mechanism by calling netdev_alloc which use kzalloc already
sets these variables to zero. This patch cleanup the setup of net_device.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch removes one check on null which should be already done by
checking before for ARPHRD_IEEE802154. All ARPHRD_IEEE802154 and
ARPHRD_IEEE802154_MONITOR should have wdev->ieee802154_ptr, where
ARPHRD_IEEE802154 is currently a node interface only.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch moves the open count handling while doing open of a lowpan
interface. We need the packet handler register at first when one lowpan
interface is up. There exists a small case when all lowpan interfaces
are down and the 802154 packet layer is still registered. To reduce some
overhead we will register the packet layer when the first lowpan
interface comes up and unregister when the last interface will become down.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Inside the IEEE 802.15.4 6LoWPAN subsystem we use two interfaces which
are wpan and lowpan interfaces. Instead of using always the variable
name "dev" for both we rename the "dev" variable to wdev which means the
wpan net_device and ldev which means a lowpan net_device. This avoids
confusing and always looking back to see which net_device is meant by
the variable name "dev".
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

if btmrvl_tx_pkt() is called, and the branch
  if (skb_headroom(skb) < BTM_HEADER_LEN)
evaluates positive, a new skb is allocated via skb_realloc_headroom.

The original skb is stored in a tmp variable, before being free'd.
However on success, the new skb, is not free'd, nor is it
returned to the caller which will then double-free the original skb.

This issue exists from the original driver submission in
 commit: #132ff4e5

If this code path had been alive, it would have been noted from the
double-free causing a panic.

All skb's here should be allocated through bt_skb_alloc which
adds 8 bytes as headroom, which is plenty against the 4 bytes
pushed on by this driver.

This code path is dead, and buggy at the same time, so the cleanest
approach is to remove the affected branch.

Reported by coverity (CID 113422)
Signed-off-by: Kieran Bingham <kieranbingham@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

With 9380f9ea the order of unsetting
the HCI_USER_CHANNEL flag of the HCI device was reverted to ensure
the device is first closed before making it available again.

Due to hci_dev_close checking for HCI_USER_CHANNEL being set on the
device it was never really closed and was kept opened. We're now
calling hci_dev_do_close directly to make sure the device is correctly
closed and we keep the correct order to unset the flag on our device
object.
Signed-off-by: Simon Fels <simon.fels@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Don't hide this packet size error.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Implement runtime PM suspend/resume callbacks.
If LPM supported, controller is put into supsend after a delay of
inactivity (1s). Inactivity is based on LPM idle notification and
host TX traffic.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Add PM suspend/resume callbacks which call lpm_suspend/resume.
Add LPM ack in threaded IRQ handler to notify the controller that
resume is complete.
Protect hci_uart against concurrent removing during suspend/resume.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Add LPM PM suspend/resume/host_wake LPM functions.
A LPM transaction is composed with a LPM request and ack/response.
Host can send a LPM suspend/resume request to the controller which
should respond with a LPM ack.
If resume is requested by the controller (irq), host has to send a LPM
ack once resumed.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Replace BT_ logging calls by the new bt_dev ones.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Replace spinlock by mutex to be able to use bcm_device_lock in
sleepable context like devm_request_threaded_irq or upcomming PM support.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Replace the device_intel list spinlock with a mutex.
devm_request_threaded_irq is not atomic and upcomming PM support should
be simpler.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Replace BT_ logging calls by the new bt_dev ones.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Enable controller Low-Power-Mode if we have a pdev to manage host
wake-up. Once LPM is enabled, controller notifies its TX status via
a vendor specific packet (tx_idle/tx_active).
tx_active means that there is more data upcoming from controller.
tx_idle means that controller can be put in suspended state.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

An IRQ can be retrieved from the pdev resources. This irq will be used
in case of LPM suspend mode to wake-up the host and resume the link.
This resource can be declared as a GPIO-Interrupt which requires to be
converted into IRQ.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Add specific bluetooth device logging macros since hci device name is
repeatedly referred in bluetooth subsystem logs.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Controllers claiming to be CSR with LMP subversion 0x0c5c don't
actually seem to be authentic CSR controllers. They also don't have
their USB bcdDevice value matching the LMP subversion like all other
CSR controllers:

HCI:

> HCI Event: Command Complete (0x0e) plen 12
      Read Local Version Information (0x04|0x0001) ncmd 1
        Status: Success (0x00)
        HCI version: Bluetooth 2.0 (0x03) - Revision 3164 (0x0c5c)
        LMP version: Bluetooth 2.0 (0x03) - Subversion 3164 (0x0c5c)
        Manufacturer: Cambridge Silicon Radio (10)

USB:

T: Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=16 #Cfgs= 1
P: Vendor=0a12 ProdID=0001 Rev= 1.34
C:* #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms

These controllers also have the HCI_Read_Stored_Link_Key command
broken so it's important the right quirk is set for them.
Reported-and-tested-by: Rhobison Alves Pereira <rhobison@hotmail.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Some counterfeit CSR controllers also have broken behavior with the
HCI_Read_Stored_Link_Key command:

< HCI Command: Read Stored Link Key (0x03|0x000d) plen 7
        Address: 00:00:00:00:00:00 (OUI 00-00-00)
        Read all: 0x01
> HCI Event: Command Complete (0x0e) plen 8
      Read Stored Link Key (0x03|0x000d) ncmd 1
        Status: Unsupported Feature or Parameter Value (0x11)
        Max num keys: 0
        Num keys: 0

Extend the existing HCI_QUIRK_BROKEN_STORED_LINK_KEY to be also used
for this HCI command.
Reported-and-tested-by: Rhobison Alves Pereira <rhobison@hotmail.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Fix build error caused by missing Kconfig dependency:

ERROR: "cdc_parse_cdc_header" [drivers/net/usb/cdc-phonet.ko] undefined!
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Many commonly used functions like getifaddrs() invoke RTM_GETLINK
to dump the interface information, and do not need the
the AF_INET6 statististics that are always returned by default
from rtnl_fill_ifinfo().

Computing the statistics can be an expensive operation that impacts
scaling, so it is desirable to avoid this if the information is
not needed.

This patch adds a the RTEXT_FILTER_SKIP_STATS extended info flag that
can be passed with netlink_request() to avoid statistics computation
for the ifinfo path.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

   In file included from drivers/usb/gadget/function/u_serial.h:16:0,
                    from drivers/usb/gadget/function/f_acm.c:23:
>> include/linux/usb/cdc.h:47:5: warning: 'struct usb_interface' declared inside parameter list
        int buflen);
        ^
>> include/linux/usb/cdc.h:47:5: warning: its scope is only this definition or declaration, which is probably not what you want
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The code around the allocation and loops are a bit obfuscated.

Neaten it by using:

o kcalloc with decimal count and sizeof(u32)
o Decimal loop indexing and i++ not i += 4
o A promiscuous block using a similar style
  to the multicast block
o Remove unnecessary variables
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Iyappan Subramanian says:

====================
driver: net: xgene: Enable 2nd 10GbE port on APM X-Gene SoC

This patch adds support for 2nd 10GbE on APM X-Gene SoC
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Adding the second 10GbE dt node for APM X-Gene SoC device tree
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adding support for the second 10GbE port on APM X-Gene SoC
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This moves cdc-phonet to the common parser for CDC users
to reduce code duplication.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This moves qmi-wwan to the common parser for CDC user
to reduce code duplication.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch uses the common parser to parse extra CDC
headers in order to reduce code duplication.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This moves cdc-ncm to the common parser for CDC user
to reduce code duplication.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>